Search Documents

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite, with length-to-diameter (LID) ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite), were broken in axial compression to determine to what extent an increase in end constraint increased compressive strength. Radial end constraints of 13 to 23% of the average axial stress in the pillar, produced by solid steel rings bonded with epoxy to the ends of dogbone-shaped specimens, increased compressive strength somewhat above that of cylindrical pillars without ring constraint. However, when the results were compared with those obtained by other investigators for straight specimens of several rock types taken collectively, with LID ratios greater than 0.5, the resulting strengths were not significantly different. Thus, the amount of end constraint produced by the solid steel rings was about the same as that produced by the friction from the steel end plates. In other tests, a radial prestress of 3000 or 5000 psi was applied prior to axial loading by adjustable hardened steel rings to increase the constraint above that obtained for the solid rings. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 3000 psi prestress, was 54.3% for limestone, 40.3% for marble, 44.7% for sandstone, and 23.4% for granite. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 5000 psi prestress, was 74.2% for limestone, 51.2% for marble, 61.6% for sandstone, and 29.7% for granite. These constraints increased the compressive strength significantly above the strength of straight specimens and solid-ring constrained specimens. These results suggest that large horizontal stresses in orebodies mined by the room-and-pillar method should increase the strength of the pillars and allow an increase in ore recovery by a reduction of pillar size when major structural defects are absent. One important objective of the U.S. Bureau of Mines (USBM) mining research program is the rational design of mining systems. In the design of room-and-pillar mining operations, pillar strength is a fundamental variable. It is customary to estimate this strength from uniaxial compression tests of rock samples and to correct this value for the length-to-diameter (LID) ratio of the in-situ pillar. This method of estimating pillar strength corrects for pillar shape but does not consider the effect of a large horizontal in-situ stress field that sometimes exists in underground formations. The purpose of the work covered in this report was to determine to what extent the compressive strengths of model pillars of relatively brittle rock loaded in axial compression were affected by lateral end constraint. In previous work, Obert l used solid steel rings bonded to the ends of dogbone-shaped specimens to study the creep behavior of three quasi-plastic rocks -salt, trona, and potash ore - during a test period of 1000 hr. These rings provided radial constraint during the loading cycle of 20 to 50% of the axial stress for specimens with LID ratios of 2, 0.5, and 0.25. He concluded that (1) "for a quasi-plastic material the end constraint strongly affects the specimen strength, and (2) as D/L increases (length-to-diameter decreases), the specimens lose their brittle characteristics and tend to flow rather than fracture." He also concluded that model pillars constrained by rings were better for use in predicting the strength of mine pillars than either cylindrical or prismatic specimens. This conclusion appears to be valid where mine pillars, roof, and floor are a single structural element. In the present study, 460 specimens of four relatively brittle rocks — limestone, marble, sandstone, and granite - were tested to failure. The study consisted of two parts: (1) the effect on the compressive strength of end constraint produced during the axial loading cycle by solid steel rings bonded with epoxy to the ends of the specimens, and (2) the effect on the compressive strength of increased end constraint produced in part by a prestress applied prior to axial loading and in part by lateral expansion of the specimen during the loading cycle. The first part of this study was reported in some detail earlier.2 EXPERIMENTAL PROCEDURE AND EQUIPMENT Model rock pillars of the sizes and shapes shown in Fig. 1 were broken in axial compression when the ends were constrained as shown in Fig. 2. he straight specimens were broken without ring constraint. The specimens of dogbone shape were broken with (1) solid

Jan 1, 1970

By Klaus Schwerdtfeger

The rate of formation of silicon monoxide from silica spheres has been measured at 1500°C in H2, H2-H2O, H2-He, H2-Ar, and CO-CO2 gas mixtures. Indications are that in the hydrogen-containing gases the reaction rate is mainly determined by convective diffz~sion. In the CO-CO2 mixtures the rate approches a constant value which is independent of sphere diometer (and gas velocity). This suggests that a surface reaction becomes rate controlling in CO-CO2 gas. WHENEVER silica is exposed at elevated temperature to a strongly reducing atmosphere there occurs, inevitably, a volatilization of silica by the formation of gaseous silicon monoxide. Because of the importance of this reaction in metallurgical processes and laboratory experiments, its kinetics were studied in the present work. EXPERIMENTAL The spheres made of vitreous silica were suspended by a molybdenum wire in the hot zone of a gas-tight high-purity recrystallized alumina furnace tube of 3.1 cm internal diam and 100 cm length. Molybdenum wire resistance heating was used. A purified H2, H2-H2O, H2-He, H2-Ar, or CO-CO2 gas mixture was passed through the tube, from top to bottom. The amount of silicon monoxide formed was determined by weighing the silica balls before and after the experiments. The silica balls were made from commercially available translucent fused quartz glass. In experiments with hydrogen-containing gases the silica stayed vitreous during the experiment, whereas in experiments with CO-CO2 mixtures, which were performed over longer times, the balls were always crystallized to cristobalite (as determined by X-ray examination) at the surface. Constant-pressure head capillary flowmeters were used to control the composition of H2-He, H2-Ar, and CO-CO2 gas mixtures. The oxygen and water vapor were removed from the gases containing hydrogen by passage through columns containing platinized asbestos (450°C) and an-hydrone. The CO was purified from O2 and CO2 by passing it through activated copper (200°C) and through ascarite. The H2-H2O gas mixtures were prepared by passing purified Hz through a mixture of oxalic acid dihydrate and anhydrous oxalic acid held at a constant temperature in a water bath. The equilibrium water vapor pressures of oxalic acid dihydrate-anhydrous oxalic acid mixtures were taken from the available data.1 The furnace system was checked for sufficient gas tightness at regular intervals. As an additional check, the H2O and CO2 contents were measured in the exit gas and were found to agree closely with the metered contents when H2-H2O or CO-CO2 mixtures were used. When purified H2 was used, H2O pressures found in the exit gas were always below 0.1 mm Hg. These contents originate either from an incomplete reoxidation of silicon monoxide in the cold part of the furnace or from small leaks which cannot be avoided. If the latter is the case, such small uncontrolled H2O contents decrease the partial pressure of SiO in equilibrium with SiO2 by less than about 7 pct, which is considered small in comparison to other experimental uncertainties. The temperature of the furnace was controlled automatically in the usual manner. The reported temperature was measured with a Pl-Pt/l0pct Rh thermocouple and was accurate to ± 5°C. TRANSPORT-CONTROL LED RATE OF REDUCTION The gaseous convective diffusion from the surface of a sphere can be predicted from the semiempirical relationship obtained by Ranz and Marshall2 in a study of the evaporation of water and benzene drops in air. The following equation applies:

Jan 1, 1967

By Donald W. Scott, Adam Wesner

This paper describes the study of 23 nonmagnetic iron-formation samples from the Mesabi Range and shows the significance of their chemical, mineral, and physical properties in terms of their concentration. Data presented here resulted from a research project carried out from 1942 to 1952 by 10 major producers of iron ore, working in conjunction with Battelle Memorial Institute. THE inevitable depletion of Mesabi direct-shipping iron ores, hastened by recent wars, has increased the importance of developing methods to concentrate iron-formation materials. Many mining companies, independent research organizations, chemical companies, and equipment manufacturers are devoting attention to this important work. It is only natural that magnetic iron-formation materials have received major emphasis, since magnetic recovery methods apply and reserves of Mesabi magnetic taconites are large. However, the nonmagnetic* iron-formation materials are likewise believed to represent a large reserve and their study has not been neglected. tions over the years have shown that in addition to the unenriched taconite, which is dense and hard, and the direct-shipping ore, there are transition taconites grading into the friable wash, or intermediate ores. The transition taconites are less massive than the unaltered taconites and usually coarser-grained. This variation, coupled with the fact that there were no extensive drillings in the unaltered taconite, posed a most difficult problem of obtaining samples that would be representative of large tonnages of the fresh rock. The problem was increased by the tremendous extension of the nonmagnetic formation materials on the Mesabi and by the question of their accessibility to mining. A drilling program was evolved that would surmount these difficulties. Selection of samples was made by a committee representing producers in the area. The samples were procured from 1—taconite walls near bodies of stripping burden or wash ore and 2—from shafts in the process of being sunk through taconite for drainage or mining operations. Most of the samples were obtained from the cherty horizons because it became obvious early in the program that the slaty horizons represented an exceedingly difficult concentration problem, owing to the character of the gangue minerals and the fine grind required for liberation of the valuable minerals. More samples were procured from the lower cherty horizon than from the upper cherty because it was more accessible to mining. It is not known how well the samples selected represent the nonmagnetic iron-formation material. However, they were chosen by people Well acquainted with the geology of the Mesabi range and the mining problems involved. It is believed that they represent a fair cross-section of the types of materials that will be encountered. Table I gives data on the origin of the 23 samples and the horizon footages from which they were obtained. Samples 1 through 10, and 15 and 16

Jan 1, 1955

By Frederick Bradley Henderson

This study was initiated to investigate the occurrence of cinnabar in the oxidation zones of some mercury sulfide deposits. Seven mines or mine districts were visited and samples were taken from both the oxidation and primary zones of these deposits in order to compare their mineralogies and assess Vie chemical changes that took place during oxidation. As a result of the study of these specimens, several limiting factors are suggested for the chemical environments and processes active in both the deposition and oxidation of mercury sulfide deposits. The Mt. Jackson mine, near Guerneville, California (location map, fig. 1), was studied in some detail and forms the basis of this paper. The mine has not heretofore been described in detail in the literature. The Mt. Jackson mine is considered typical of mercury sulfide deposits occurring at the faulted boundaries of serpentinite bodies and enclosing sediments. Such mines are common in the California and Oregon Coast Ranges? Specimens collected by the author from the New Idria and New Almaden districts, the Mt. Diablo, the Culver Bear, and the Buena Vista mines in California, and the Opalite district (Cordero and Bretz, mines) on the Oregon-Nevada border were studied for comparison with the Mt. Jackson samples. The mine description, maps and sketches were composed from field maps kindly provided by Francis Fredericks, consulting geologist to the Sonoma Quick-silver Mine Inc. during the author's visit in 1962. Additional information was obtained from the company maps and minor corrections and interpretations were added by the author.

Jan 1, 1965

By J. B. Bassett, E. S. Rowland

The experimental work reported herein firas inspired by the publication of a paper by Grange and stewart, in which it was suggested that at low chromium contents the effect of this element on the Ma point was greater than at higher chromium contents, It was argued that, if a small increase of chromium in solution in austenite caused a sharp lowering of the M, point, it might lead to an explanation of occasional unsolved stress cracking of SAE 52100 during heat treatment. Commercial hardening is carried out at temperatures of incomplete solution, leaving carbides available to enrich the austenite during any inadvertent increase in temperature, such enrichment of the austenite in chromium content would lower the M, point nearer room temperature where cracking is more likely to occur. According, it was decided to investigate the effect of chromium, in quantities between o and 2 pet, on the M, point of commercial steels. Fig I summarizes the data available on chromium steels. For purposes of comparison, the M, temperature values were corrected by means of the Grange and Stewart formulas to (I) Hypoeutectoid compositions: 0.50 pct carbon and 0.80 pct manganese (z) Hsereutectoid compos-sition': 1." pet carbon and O.35 pct manganese. Only the steels having compositions reasonably close to these corrected values were included, because large adjustments inevitably introduce increased error such as are experienced in using the formula. The straight lines of Fig I were drawn by the authors. These data obviously do not settle the question Of the effect Of chromium On the Md Oint, particularly at low chromium contents. While it is fairly well established that chromium causes the M, to be lowered when present in quantities of I pet Or more, Grange and Stewart1 have suggested that in small amounts (less than 1 pet) it is more effective in lowering the Ma point, while Klier and Troiano2 have suggested that in small amounts it is less effective in lowering the Ma point. Payson and Savage3 concur with Klier and Troiano and further suggest that the effect is not linear at these concentrations. Rose and Fischer4 report that small amounts of chromium actually raise the Ma point of a 0.20 carbon steel. Material Two series of 35 Ib induction heats were melted for this work, the analyses of which are given in Table I. One series was aimed at 0.50 pct carbon and 0.80 pct manganese with chromium additions in 0,25 pet increments from o to 1.5 pct with a single heat at 2.0 pct Cr. This series was considered necessary because the commercial heat treatment of SAE 52100 does not generally introduce more than about 0.60 pct carbon in solution in the austenite. The high

Jan 1, 1949

By John Henry Harden

WITH imperfect instruments it is impossible to make accurate surveys; the results are inaccurate maps, with their attendant consequences. The design of the writer is to describe an improved form of tripod head, and certain defects in an English transit and a miners' dial, with the method taken to remedy the defects of the transit. When the present transit superseded the surveyor's compass, there was one special objection brought against it, and with some show of reason ; namely, that the tripod of the compass with its ball and socket motion, allowed a quicker levelling-up (and, consequently, more work) than was possible with the transit. To this objection it was replied, that the ball and socket would not allow the instrument to be levelled with the same degree of precision that could be attained with the levelling screws, and that if time was sacrificed greater accuracy was attained. Nevertheless, it is a well-known fact that in this country, and especially in England, the compass or miners' dial holds its ground solely from its rapid adjustment. Ever since the introduction of the transit, efforts have been made to give to this instrument the same facility of levelling possessed by the compass or dial, and the same means have been tried, i. e., a . ball and socket motion, since a modification of this in some form was the only method that would answer. The upper part of a transit is, however, much heavier than the corresponding parts of a compass, and, therefore, requires more binding power, which cannot be ob¬tained with an ordinary ball and socket joint. It has been a study with instrument-makers to combine the facility of these two tripods -the quickness of the ball and socket with the steadiness and accuracy of the screws; but in all attempts in this direction the ball and socket of the compass has been literally followed, the entire stability of the instrument depending upon the friction of the ball in its socket. There is great need for a tripod that can be more easily manipulated than the present form, for it rarely happens that an engineer has a level surface on which to set his instrument, and very often

Jan 1, 1879

By N. S. Dalal, Xianglin Shi

"INTRODUCTIONEpidemiologic studies of workers in chromate-ore related industries, 1-3 and stainless steel welding and related occupations4 have shown that they have about 20-40 times higher risk of throat or respiratory track cancer than controls. Although the actual carcinogenic substances were not identified in these statistical studies, Cr(VI) compounds (for example, calcium chromate, zinc chromate, and lead chromate) were implicated as the causative agents, whereas Cr(III) compounds were not suspected as carcinogens. s These suggestions were supporte4 by laboratory studies wherein many Cr(VI) compounds produced sarcomas at the implant or injection sites.1,5 Squamous cell carcinomas and adenocarcinomas closely resembling human lung cancer were induced by intrabronchial implants of calcium chromate in rats, 6·7 whereas Cr(DI) oxide and Cr(lll) sulfate did not induce any tumor formation.6,7While the mechanism of the chromate-induced carcinogenicity is not fully understood, it is generally thought8 that it involves some damage to DNA. Specifically, it has been reported that: a) the chromate ion, henceforth referred to as chromate, can pass through the cell membrane and enter the cell while CR(DI) does not, 9 b) chromate does not interact with either native or denatured DNA 10 while Cr(III) does, 11 and c) the final Cr-DNA complex isolated from cellular reactions of chromate is Cr(III)-DNA, with Cr(III) binding to the phosphate groups.12,13 Thus the important question is: since Cr(DI) cannot pass through the membranes, how does Cr(III)-DNA complex form? For this to happen, Cr(VI) must be reduced to its lower oxidation states, 14 ultimately to Cr(III), by some reductants in the cellular environment. Unless this reduction occurs, the DNA would not be damaged and therefore no chromate carcinogenicity would ensue. Thus the reduction of chromate to its lower oxidation states seems to be a key step in the chromate carcinogenicity .1s One of the major reductants in cellular environments is thought to be glutathione (GSH), both outside and inside the cells.16-lB Some evidence for the role of GSH in the chromate toxicity was provided by recent studies showing that exposure of hamster cells to non-toxic levels of added selemite increases the levels of GSH as well as the Cr(VI)-induced DNA strand breaks,19 and that such DNA strand breaks in hepatocytes also change in direct proportion to the GSH content. 20,21 These observations were interpreted as implying that the reduction of chromate by GSH to some reactive intennediate is an important step in the chromate carcinogenicity. 20.21 In · the present undenaking22 we have used electron spin resonance (ESR) and spin-trap methodology to investigate the reduction of chromate by GSH and find evidence for the involvement of the glutathionyl radical (GS ·) as well as Cr(V)-intermediates."

Jan 1, 1990

Continued discussion of the paper of R. W. Raymond, presented at the Cleveland meeting, October, 1912, and printed in Bulletin. No. 70, October, 1912, pp. 1111 to 1122. See also discussion printed in Bulletin No. 74, February, 1913, pp. 319 to 329. R. B. BRINSMADE, Puebla, Puebla., Mexico (communication to the Secretary *) :-Though I heartily approve of several minor points emphasized by Dr. Raymond (such as the general desirability of local administration, rather than Federal, and the evils inseparable from the Federal Apex Law), I feel obliged to dissent from his four final propositions. As Dr. G. 0. Smith has already discussed these propositions from the standpoint of the experience of other countries, I shall base my criticism upon certain general economic principles, which will be grouped under the following five topics: 1. The dual theory of property. 2. The essential factors in fixing prices. 3. The relation of land ownership to the distribution of wealth. 4. The relation of land ownership to speculation and development. 5. The relation of land ownership to the political power. I shall give here only a brief outline of these topics, as they are fully treated in the standard treatises on political economy.1

Jan 5, 1913

By W. Ferreira

Steel is produced in a basic oxygen furnace from hot metal obtained from a blast furnace. A sintered iron ore with good hightemperature properties (strength and permeability) should be used as feed to the blast furnace. The quality of this sintered ore depends on the reactivity of the iron ore used as feed to the sinter plant during the lime assimilation step in the sintering process. The penetration test is the standard method for evaluating the reactivity of iron ore with lime. It is, however, difficult to determine the exact depth of penetration from the standard test. A new test method is proposed that allows automatic evaluation of iron ores in terms of lime assimilation with increasing temperature. A comparison of the coefficients of variation for the new and standard methods for each ore type demonstrates that the results of the new test are more reproducible and more precise than those of the standard method. The test is also less time-consuming and easier to implement.

Jan 1, 2014

By Leslie Taylor, Kevin Genson

This paper reports on an experimental study of the effect that bottom shaping might have on the impulse delivered to a light armored vehicle due to a buried mine detonating beneath the center of it. The study was restricted to explosives buried in saturated sand and three parameters were varied within the study: bottom angle (0 degrees to 21 degrees), depth of burial of the explosive (1.02 mm to 12.7 mm), and stand off distance (0 mm to 38.1 mm). Six hundred and thirty six milligrams of explosive was used as the explosive load. It has been shown in previously published work [1,2] that Hopkinson scaling works well for the determination of impulse loading on a semi-rigid target plates. Therefore in terms of a full scale test using 4.54 Kilograms of explosive the parameters investigated would cover a DOB of from 19.56 mm to 243.84 mm and a Stand off distance from 0 to 734.06 millimeters. These values nicely cover those of interest to the Marines with regard to the AAV (amphibious assault vehicle). Four angles were investigated at all DOB’s and Stand off distances – 0 degrees, 7 degrees, 13 degrees, and 20 degrees. The results show that reduction in impulse delivered to the target is achieved with an angled bottom on the target plate with a major reduction occurring before the 13 degree angle is reached. Hence vehicles with quite modest bottom angles could help greatly in load reduction with very little loss in utility.

Jan 1, 2008

Polyacrylamide flocculating agent has been used in the Leaching Division of the Risdon Works of the Electrolytic Zinc Co. of Australasia Ltd since October, 1960. Since the introduction, the.: number of thickeners in use in the continu-ous thickening stage has been reduced from eight to three; there has been an increase of 25% in throughput and a reduc-tion of solids in.:thickener overflow from 3-4 gòpòl . solids to 0.5 g.p.l. solids. Reagent addition has been at the rate of 0.25. lb SEPARAN, NP10 per ton solids.Additionally there has been a gain of 3% in current efficiency as the direct result of the addition of SEPARAN NP10 to purified cadmium sulphate solution prior to electrolysis for cadmium metal. A smoother deposit has resulted and it has been possible to increase deposition time between strip-pings from 47 to 71 hours. However, there has been a slight increase the lead content of the cadmium-metal produced.

Jan 1, 1963

By R. W. Smith

IN the manufacture of portland cement, the basic and fundamental essential is a limestone uniformly rich in calcium carbonate and carrying less than 3 per cent magnesium carbonate. In searching for such a deposit, also having in mind quantity of rock, accessibility and quarrying facilities, the Pacific Coast Cement Co. discovered and developed its present quarry at View Cove on the east coast of Dall Island, Alaska. Dall Island is about 100 miles west of Ketchikan and 650 miles north from Seattle. It is 70 miles in length and 5 to 10 miles in width. The climatic conditions are much more favorable than would be expected. The temperature ranges from zero to 70 degrees. The precipitation is considerably more than at Seattle, although there was less snow during the last season than at Seattle. The island is rugged and mountainous; the vegetation is moss and grass and a large portion is timbered with spruce, hemlock and cedar. Some of this timber has market value. The limestone quarry is about 30 miles north of the extreme southern end of the island. The company acquired 240 acres which contain limestone of remarkable uniformity, the percentage of calcium carbonate being about 95. It is estimated that there is ample recover- able rock on the holdings to supply the cement plant at its maximum capacity for well over 100 years.

Jan 1, 1929

By Artur Fernando de Vito Júnior

Caracterizar propriedades de resistência à propagação de trinca em aços é um elemento central em métodos de avaliação de integridade estrutural. Tal caracterização, normalmente se dá por meio da obtenção de curvas de resistência à propagação estável de defeitos (curvas J-R) do material. Sendo assim, para tornar este estudo mais amplo, serão obtidas curvas J-R de um aço estrutural com o objetivo de elaborar um roteiro metodológico para obtenção de curvas J-R. O ensaio de tenacidade à fratura para obtenção da curva J-R foi conduzido utilizando a técnica do corpo de prova único (single specimen) empregando o método da flexibilidade no descarregamento (unloading compliance), segundo a norma de ensaios ASTM E1820. Para este estudo, foram utilizados corpos de prova compactos C(T) de espessura B=10,0 mm, largura W=2B e uma relação aproximada entre o tamanho de trinca (a) e a largura, a/W=0,5.

Aug 8, 2018

By Blaycock. S. C.

WE should indeed feel proud and satisfied with the accomplishments of our great mining and metallurgical. industries during the past quarter of a century, for they have vastly exceeded those of any previous period of like duration. 1 feel that Canadians, and particularly those in the mining industry, should know more concerning the important role our industry will be called upon to play in the present war. Our Empire metals will be an outstanding factor in this conflict. Every man connected with the industry, from the lowest paid labourer to the highest official, can feel proud that his every effort results in more and more production of those metals which will help to give the Empire supremacy. He can feel assured that, by sticking to his job and by putting his whole heart into his work, he is making a contribution towards winning the terrible struggle in which our Empire and our gallant French allies are engaged. These two great peoples will have ro bear the brunt of the task of ridding the world of the menace of those who would set up force. and might in the place of right and justice in the settlement of international affairs. As the present European crisis developed, it became evident that they, alone, would have to accept the challenge and fight the enemies of Democracy to ensure the survival of the small nations of Europe and, indeed, of the great democratic powers themselves. The acquisitive eye of the German leaders had looked far ahead and they had realized that the eastern European states, already reeming with population, were no solution to Germany's space problem; but they thought that these states could be gobbled up one by one, each in turn strengthening Germany's might until it could successfully challenge France and England. No glimmer of doubt dimmed their vision. The two great democracies once subdued, they could proceed to seize Canada and the United States. This clone, they would have an abundance of room to expand, as well as those resources-grain, timber, cotton, nickel, iron, lead, zinc, copper, gold, silver, sulphur, oil-which German statesmen have always coveted. Von Ribbentrop, von Alvensleben, Bernstorff, and many others have made exhaustive studies of our resources. German rulers had been told that the French would not fight and that the British could not. They knew of the rust on the British war machine. There was no cloud in the sky; their fond dream was at last robe fulfilled.

Jan 1, 1940

By M. Sakamoto, S. Karaswa, Y. Yoneoka, Y. Ohmizo

"The Annaka Refinery has been processing leach residue by Waelz process for 17 years. Recently, the quantity of the leach residue has increased due to a decline in the quality ~f zinc concentrate. Meanwhile, negative factors (e.g. deterioration of water balance due to improved electrolytic power consumption rate) have increased· in the processing of the leach residue.We have implemented various measures in responses to this situation, while striving to increase ·processing capacity and achieve stable operation. AS we have largely completed our assessment of the efficacy of these measures, we report on our recent process improvements.IntroductionWe have been treating leach residue by the Waelz kiln process since 1981. At that time, treatment of only 50,000 tons of leach residue per year was anticipated. However, subsequent process improvements have revised this figure up to 75,000 to 80,000 tons per year.However, today's increased Fe zinc concentrate grade has resulted in increased amounts of leach residue. In addition, improvements have reduced electrolytic power consumption rate of zinc electrolysis, limiting the amount of water that can be used in ·the zinc refining processes and for deaning leach residue. Consequently, we encounter an increasing number of problems and factors adversely affecting leach residue treatment, including increases in water-soluble Zn (WsZn) and. S (S04) in leach residue.To solve these problems, we have taken several measures to ensure long-term continuous operation and treatment of this increased · amount of leach residue. This paper discusses these measures."

Jan 1, 2000

STANFORD UNIVERSITY, CALIFORNIA Our activities for the year 1918-19 have closed with the coming of summer. It has been a most successful year in many respects, especially in the reorganization necessary after the war conditions had passed. An INITIATION SCENE AT STANFORD UNIVERSITY. "old-days" initiation was held on the Stanford campus by the Society a few weeks ago. The accompanying picture explains some of what took place when the following men were taken into the membership: W. P. Winham, Salinas, Calif. ; T. L. Wark, Long Beach, Calif.; P. L. Henderson, Greeley, Colo.; T. E. Bassett, Palo Alto, Calif.; and R. G. Wheelton, Long Beach, Calif. CHAS. A. DOBBEL, Secretary.

Jan 8, 1919

By D. Sharma, A. K. Singh, R. Singh, P. K. Mandal, M. Sarkar

"This paper deals with the stability investigations carried out at the XIVth seam of Jitpur colliery. The study was conducted to investigate the possible causes of roof cavity formation and face spalling at the middle slice face of block-3 longwall panel and to suggest remedial measures. The instrumentation and monitoring work was carried out in the panel over a period of nine months. On the basis of observations, it was found that if the maximum face span was reduced from the existing 4.8 m to 3.6 m, and if the face time schedule cycle was reduced from a maximum of 37 days to about 18 days, this problem could be eliminated. The recommendations of CMRI have been implemented in the middle slice face of block-4 panel with success. IntroductionModerate to steeply dipping, undisturbed seams of uniform thickness are worked by way of inclined slicing parallel to walls. In this method, the seams are treated as a combination of several moderately thick seams dipping parallel to roof and floor. Numerous variations of multislice mining have been used worldwide to get high coal recovery under local conditions of geology, subsidence control, proness to spontaneous combustion, statutes and economics. Multislice mining can proceed either downward descending from the roof or upward ascending from the floor. Ascending methods require backfill behind the working face to provide a base for the next slice. It is also adopted for surface protection against subsidence or mining under a massive roof. This paper presents a scientific study conducted in Jitpur colliery, IISCO where a 9 m thick seam is mined in three slices in ascending order with stowing."

Jan 1, 2002

By W. Zhang

"The adsorption of collector on bornite has been studied in situ in aqueous solutions by applying an atomic force microscopy (AFM). The AFM images show that xanthate, such as potassium ethyl xanthate (KEX) and potassium amyl xanthate (PAX), adsorbs strongly on bornite mainly in the form of insoluble metal xanthate, which binds strongly with the mineral surface without being removed by flushing with ethanol alcohol. This adsorption mechanism is very similar to the one obtained with chalcocite/xanthate system. However, the result also clearly shows that the adsorption of xanthate on bornite is totally different from its adsorption on chalcopyrite, during which oily dixanthogen is the main adsorption product on chalcopyrite surface. The obtained AFM images also showed that the adsorption increases with increasing the collector’s concentration. When Cytec Aerofloat 238, a dialkyl dithiophosphate collector, is used, it adsorb on bornite mainly in the form of an oily substance, which can be rinsed off mineral surface by flushing with ethanol alcohol. AFM images also show that the adsorption of Cytec Aerofloat 238 increases with increasing the adsorption time. INTRODUCTION The adsorption of collector on mineral surface is vital for a successful flotation process to achieve a satisfying recovery. Historically, many works have been carried out to clarify the adsorption mechanism of collectors on sulfides. (Gaudin and Schuhmann, 1936, Poling and Leja, 1963; Allison et al., 1972, Fuerstenau, 1982; Leja, 1982; Woods, 1984) Compared to other copper minerals such as chalcopyrite and chalcocite, much less work has been done to study the adsorption collector on bornite. Allison et al. (1972) studied the reaction products of various sulfide minerals with xanthate solutions and reported that the measured rest potential of bornite in 6.25×10-4 M KEX solution at pH 7 was +60 mV and the reaction product of PAX on bornite was cuprous alkyl xanthate. Mielczarski and Suoninen (1984a, 1984b) applied the XPS and studied the adsorption of potassium ethyl xanthate on cuprous sulfide. It was reported that there was a relatively rapid formation of a well-oriented monolayer of xanthate ions followed by a slow growth of disordered cuprous xanthate molecules on top of this layer. Buckley et al. (1984) investigated the surface oxidation of bornite by linear potential sweep voltammetry and X-ray Photoelectron Spectroscopy and proposed the adsorption products on bornite depended on the solution potential. Zachwieja et al. (1987) studied the electrochemical flotation of the bornite-ethylxanthate system and reported that KEX reacted with bornite through an electrochemical oxidation reaction forming cuprous xanthate between -0.4 and -0.2v (SCE). Hangone et al. (2005) studied the flotation of a bornite-rich copper sulfide ore using thio collectors and their mixtures and reported that the highest copper recoveries were obtained with the diethyl dithiophosphate (di C2-DTP)."

Jan 1, 2016

By W. E. Lamont

The Bureau of Mines studied the potential for recovering marketable barite concentrates that meet oil well drilling-mud specifications from barite waste pond materials. The study was conducted as part of the Bureau's research program to conserve domestic mineral resources by advancing mineral recycling technology. The samples, which were obtained from Georgia, Nevada, Missouri, and Illinois, varied widely in character, particle size, and barite content. The samples were treated with sodium silicate and sodium cetyl-stearyl sulfate and then floated. The flotation flow sheet was modified to reject barren coarse and/or slime fractions from some of the samples, and one feed sample had to be scrubbed prior to flotation to remove residual flotation reagents. The cleaned concentrates had BaS04 contents ranging from 95.0 to 96.9 percent, while recovering 81.2 to 95.9 percent of the barite in the feed. The specific gravity of each concentrate exceeded the specification of 4.2. The removal of the flotation reagents from the flotation concentrate was not investigated.

Jan 1, 1982

By Kurt Oakes, John Williams

Placer Dome, US operates the Bald Mountain Mine. The Bald Mountain Mine is a surface operation located in remote northwestern White Pine County in east-central Nevada, approximately midway between Elko and Ely. The mine is in the Newark Valley along the southwestern flank of Bald Mountain a part of the Ruby Mountain range, at an approximate elevation of 7,500 ft (2,286 m). The geology at the Bald Mountain Mine is highly altered, both mineralogically, and structurally. Highwall stability and control have long been an issue at the operation, due largely to the varying geologic conditions. In some blasts as many as seven distinct geologic unconformities exist. These unconformities affect both final high wall integrities, as well as blast fragmentation characteristics. A 60 million ton (54.5 million tonnes) layback expansion of the existing “Top Pit” as well as development of a new satellite pit, “Sage Flats”, is being undertaken. Design final highwall pit slopes have been steepened from the traditional 47º to 55º in order to reduce overall ore-to-waste ratios, thereby improving economic viability for the expansion over the 4.5 year life of the project. With the increased usage of electronic detonators throughout the mining industry, mine operations staff, as well as representatives from the mines explosive supplier felt that an evaluation program incorporating electronic detonators would be warranted. The areas of focus for this evaluation would be resultant highwall pre-split integrities, peak particle velocity measurements (both near field and far field), frequency measurements, loader productivity, and visual interpretation of the results. The mine incorporates 25 ft (7.6 m) benches and uses separate trim blasts in conjunction with production blasts in order to reduce blast effects along final highwalls. Hole diameters in production blasts are 7? ” (200 mm). Typical production blast patterns are 18 ft x 18 ft (5.5 m x 5.5 m), drilled in a square pattern configuration. Shot sizes vary greatly, ranging from 200 holes to as many as 800. Bulk low percentage ANFO/emulsion blends are utilized as the redominant blasting agent. Non-electric dual delay detonators (25 ms/500 ms), with non-electric surface delays are the initiation system utilized in production blasts. Typical production blast design

Jan 1, 2004