Search Documents

By E. J. Dulis, G. V. Smith

AS reported several years ago,' nitrogen may be taken up from the atmosphere by austenitic Cr-Ni steels during creep or creep-rupture tests. This was indicated by chemical analysis and by the appearance of a new microstructural phase, or phases, tentatively identified as chromium nitride (S), at the surface or at the intergranular cracks associated with fracture. The nitrogen pickup was observed to be dependent on time, temperature, and deformation. In a more recent investigation, a sample was obtained in which there was sufficient of the precipitate to suggest that it could be readily identified by X-ray diffraction. This sample had been taken from a 1/4 in. diam creep-rupture specimen of annealed, type 304L stainless steel of the following initial composition: C, 0.03 pct; Mn, 0.65; P, 0.010; S, 0.019; Si, 0.54; Cr, 19.50; Ni, 12.02; N, 0.031; and Al, 0.005. The specimen had ruptured after 10,470 hr at 1500°F (2000 psi). In this case nitrides were distributed across the whole section of the sample, Fig. 1. The precipitate occurred both at the grain boundaries and within the grains; the latter precipitate had in some cases the appearance of pearl-ite, and in others was distinctly Widmanstatten. Chemical analysis of the sample after test showed 0.64 pct "soluble" nitrogen (soluble in 1:1 hydrochloric acid: water) and 0.18 pct "insoluble7' nitrogen (insoluble in the hydrochloric acid solution but dissolved by fuming sulphuric acid). For identification of the precipitate by X-ray diffraction, the matrix in the surface layer of the specimen was dissolved by prolonged attack in an alcoholic solution of picric and hydrochloric acids. The appearance of the specimen surface after such etching is shown in Fig. 1c. The diffraction pattern of the surface-concentrated precipitate was obtained with a recording spectrometer in both the forward and back-reflection regions (the latter by adapting a special fixture to the conventional X-ray unit). The observed X-ray diffraction lines, Table I, show the presence of Cr,N and CrN; the agreement with interplanar spacings calculated from reported data2,3 is quite good. Since it has been suggested' that CrN dissolves only in concentrated sulphuric acid, whereas Cr2N dissolves in dilute hydrochloric or sulphuric acids, an effort was made to distinguish between the two nitrides. This proved possible, inasmuch as etching in a dilute solution of hydrochloric acid gave a sample in which microscopic examination showed that much of the Widmanstatten-pearlitic precipitate within the grains had been eaten out, leaving the grain boundary precipitate in relief, and which, when examined by X-ray diffrac-

Jan 1, 1953

THE area of the State of New South Wales is not great, nevertheless it has very large and important Mineral Resources. This is the more noticeable when the values of the annual mineral production from the individual States of the Commonwealth arecompared with the value of the New South Wales production. The principal minerals mined now are not gold, copper, and tin, as they were in the early years following the gold rush of 1851, the centre of gravity of commercial mineral activity having moved to coal and "oil-shale," water, limestone (with cement), silver-lead-zinc cadmium, sulphur, slate and other building and ornamental stone, road materials, and clays.From small areas totalling only 650 sq. miles, coal to the extent of 311,000,000 tons, valued at £151,000,000, has been won.The estimate of actual and probable reserves by the Mines Department within an area of less than 1000 sq. miles is about 14,000,000,000 tons, while the potential reserves within the remaining 15,500 sq. miles of concealed coal fields must be enormous. Even taking into account only the actual and pI:obable reserves in the 1000 sq. miles known, and assuming a depletion at the rate of 350,000,000 tons a year, or somewhat greater than that of the British Isles at present, and assuming an average value of £1 a ton, with money at 5% compound interest, then the present value of this coal (40 years of depletion) would be £5,575,000,000 approximately: truly an enormous present value for a business of 40 years, dealing only with 1000 sq. miles of country. The location of the main coal basin in New South Wales is one of great strategic importance. It lies almig and near a seaboard, with excellent facilities for anchorage; the coal is of very high quality, and is readily accessible; the climate is admirable. Were this same coal at Port Darwin, its commercial importance would not be be pronounced.

Jan 1, 1926

Good blasting practices based on the careful application of explosive energy lead to significantly safer mining operations. Case studies demonstrate how the selection of the correct charge mass, explosive type and round design are vital for extracting the exact amount of rock required and preventing spurious damage to the remaining rock mass. In other cases the explosives are applied to precondition the rock mass, design rockburst resistant support, prevent damage to important excavations and reduce the exposure of miners to unsafe conditions. The Hybrid Stress Blasting Model is used to understand the explosive rock interaction and to illustrate and contrast good and bad blasting practices. In all cases, good supervision is required to continue safe mining according to the design. Keywords Blasting, safety, production, preconditioning, explosives, numerical modelling, drop raising, vibrations, and presplitting.

Jan 1, 2011

By Ivette E. Torres

World investment 10 all mineral and mining industry sectors is not available. However, partial information available provides some information useful for analysis. Information available in this section covers limited geographic information on investment in the steel industry, limited information for petroleum industry capital spending, and total U.S. foreign investment in comparison to the mineral-related sectors (tables 13, 14, and 15). Annual steel industry investment is available for the European Community, almost all countries within the European Free Trade Association (EFTA), Latin America, and other countries with significant mineral industries, such as Canada, Japan, and the United States. Although information was not available for 1992, data for 1991 indicate that for those countries aforementioned, total investment increased by 8 %. However, investment patterns were very different within the different groups of countries. While the European Community had a net increase of 12 %, dominated by an almost °40 % increase in Germany, EFTA member countries had a 26 % decrease in investment for the same period. Investment in EC countries was almost seven times that of EFT A countries. Japan's investment in the iron and steel industry, by far the largest of those available, almost twice that of the EC and almost four times that of the United States, increased by more than 20 %. In North America, investment in Canada and the United States decreased. Almost all of Latin America decreased investment in the sector. The notable exception was Mexico, with a 60 % increase. Changes in Mexico's investment policies of the recent past, its economic growth, and privatization of its iron and steel industry are some of the reasons for such an increase. The other country covered individually in Latin America, where investment in the iron and steel industry increased, although slightly, was Argentina. This limited information does not allow a comprehensive analysis of global industry trend, which in turn impacts many other mineral commodities, and with the transition in many countries within Europe and Central Eurasia that are now effecting the steel industries of the countries that were members of the U.S.S.R. and its CMEA partners, it is most regrettable that comprehensive and comparable data, both current and historic, on investment in this area are not available.

Jan 1, 1994

By Bhawani Singh, Mahendra Singh, N. K. C Samadhiya

"Inherently anisotropic rocks occur in abundance at many rock engineering project sites in Himalayan region. These rocks pose difficulty in analysis and design due to their direction dependent strength behaviour. Moreover the strength varies in a non-linear manner with confining pressure. Mohr- Coulomb strength criterion is widely used by geotechnical engineers for defining strength of rocks subjected to given confining pressure. However, the conventional Mohr-Coulomb (MC) criterion suffers from the limitation that the strength is treated to be linearly dependent on confining pressure. In the present article, the MC criterion has been modified by incorporating non-linear term while retaining the original parameters c and ?. The non-linearity with confining stress level has been imbibed through critical state concept (Barton, 1976). The criterion has been applied to a triaxial test data base comprising of more than 1140 triaxial tests conducted world-wide on anisotropic rocks. Statistical evaluation of the goodness of fit of the proposed criterion to the data-base has been carried out. Further the predictive capabilities have been evaluated by determining the error in estimation of triaxial strength if only few triaxial test data are available for determining the criterion parameters. The data base has also been back-analysed to assess the critical confining pressure for anisotropic rocks. Statistically the critical confining pressure, for the present criterion, may be taken nearly equal to 1.25?cmax, where ?cmax is the maximum value of the UCS out of all orientations of planes of anisotropy. It is concluded that reasonably good estimates of the anisotropic strength are possible through the proposed criterion.INTRODUCTIONMany rocks encountered in Himalayan region like shale, slate, schist and phyllite are inherently anisotropic and exhibit direction dependency in their strength behaviour. In addition, the strength of the rock also depends on the confining pressure and, the strength response is non-linear especially when the confining pressure may vary over large range. Conventionally, Mohr-Coulomb criterion is the most widely used criterion for rocks. However, the limitation of this criterion in its present form is that the strength is treated to be linearly dependent on the confining pressure. The present study attempts to address the following two main objectives: i) Include nonlinear response in the Mohr-Coulomb criterion while retaining parameters c and In their original form; and ii) consider anisotropic response of the rock for a given confining pressure. A nonlinear strength criterion, which uses shear strength parameters c and as per Mohr-Coulomb criterion, has been suggested based on critical state concept for rocks."

Jan 1, 2015

By M. Abdellatif

"SynopsisCalcined basic nickel carbonate (BNC) concentrate was smelted in a pilotscale DC arc furnace to produce a nickel metal. The furnace was continuously operated for 12 days (24 hour/day), during which twelve different smelting conditions were investigated, with the major variables being reductant type and feed rate, flux composition and addition, and BNC feed rate.The 200 kW DC arc furnace was operated at power levels between 110 and 165 kW and at a total feed rate of 78 to 96 kg/h, resulting in an average slag and metal tapping temperature of about 1650°C. A total of 7.2 t of BNC were smelted, producing about 5.44 t of nickel metal and 2.94 t of slag. Nickel recoveries of 96.4% and higher were achieved, and the slag nickel content was as low as 0.1%. The major impurities in the metal were iron (mostly from oxygen lancing) and carbon. The calculated feed carry-over was less than 0.85% and the graphite electrode consumption was between 2.8–3.3 kg/MWh.IntroductionOne of the most distinctive advantages of DC open-arc smelting is the ability to process fine raw materials without any major issues with regard to the operability of the furnace, metal recovery, and metal quality. This has been demonstrated in Mintek’s DC arc pilot plant facilities over a period of about three decades (Curr et al., 1983). The materials that have been processed include laterite (Kotze, 2002), chromite fines (Curr et al., 1983), manganese fines (Lagendijk et al., 2010), PGM concentrates (Shaw et al., 2013), electric arc furnace (EAF) dust (Denton et al., 2005; Abdellatif, 2002a) and stainless steel (SS) dust (Denton et al., 2005; Abdellatif, 2002a; Goff and Denton, 2004), and petroleum fly ash (Abdellatif, 2002b). The top particle size of such materials can vary from a few millimetres (e.g. laterite) to micrometres (EAF and SS dust). Dusting, whether due to physical carryover of feed or to the arc side reactions, has been proven to be a non-issue. As such, the applications of DC open-arc furnaces have the potential to be extended to other raw materials such as particulate nickel oxide, which has a particle size much less than 100 µm.Nickel oxide is typically produced from laterite ore by sulphuric acid leaching, purification, and precipitation as basic nickel carbonate (BNC) (Rhamdhani, Jak, and Hayes, 2008) or as mixed hydroxide precipitate (MHP) (Mackenzie, Virnig, and Feather, 2006), and finally calcining at moderate temperatures (800–1200°C). The NiO product is very fine, with an average particle size in the range of 10–20 µm and a NiO content of more than 99%."

Jan 1, 2015

The industrial practice of separating finely' around valuable minerals from associ- ated gangue materials by froth flotation is well known. Despite the obvious importance of this industrial process, the predictive tools for plant engineering evaluation of flotation process variable changes are still in a developmental stage. Consider, for example, the situation where an operating engineer is faced with evaluating a change in an existing chemical reagent scheme, possibly based on batch laboratory data. When all is said and done, the engineer must still perform detailed physical testing of the proposed reagent change on the actual equipment in plant use to be confident even of the direc- tion of change of plant results, let alone the economic viability of the change. The theory behind chemical reagent behaviour in froth flotation has been studied extensively, e.g., (Aplan {1980}, Fuerstenau {1976}, Fuerstenau {1962}, and Somasundaran {1980}), and, certainly, important progress has been made. Unfortunately, the nature of the flotation process, with its complicated heterogeneous surface chemisty activity operating on highly variable and difficut to characterize ore surfaces, coupled with com- plex mass and momentum transfer phenomena, :;l riously compromises the plant scale predictive capability of theoretically based models.

Jan 1, 1978

By Barrie C. Butt

The opportunity for an exploration geologist to follow a successful exploration project through the feasibility, financing, construction, development and exploitation phase is rare. In addition, it is not often that the exploration geologist can be present during the mining of a deposit to explain why certain actions were taken or interpretations made and to find out how these interpretations turned out in actuality. At the Woodsreef chrysotile asbestos mine in New South Wales, Australia, mining has been in progress for six years and the writer has been intimately associated with the project during the five years of exploration and the six years of exploitation. The industry is possibly aware of the fact that the Woodsreef Mine has had major production problems, the majority of which have stemmed from the unique characteristics of the ore body and of the fibre. Because of these unique features, a large volume of research has been undertaken by Woodsreef and by other scientific organisations in Australia, England and Canada on the Woodsreef fibre. The answers to some of the problems have negated some semi-sacred concepts of asbestos ore milling and led to the development of new techniques, such as the adoption of microscopic fibre counts as a routine procedure; the modification of accepted evaluation procedures; the development of new machines for dedusting fibres, and to the recognition of a fibre with a unique milling behaviour pattern and, possibly, properties. The problems experienced can be divided broadly into those associated with the geology and those associated with the physical properties of the fibre. It is possible that the same features may manifest themselves in other deposits around the world, and if they can be recognised during the exploration stages a feasibility evaluation may be just that little closer to the actual.

Jan 1, 1978

By W. A. Straw

IN the manufacture of telephone apparatus a number of nonferrous sheet metals are blanked and formed to produce a wide variety of parts, which are generally small in size because of space and weight requirements. Many are given sharp bends in forming, so that they may be assembled into compact units. This study covered sheet metal of the alloys of brass, phosphor bronze and nickel silver that are most extensively used by our company. In general, the sheets range from 0.005 to 0.100 in. in thickness and from 1/4 hard to extra spring temper in hardness. As many parts function as flat springs, and others require the maximum stiffness for structural reasons, a large percentage of the metal is used in the hard and spring tempers. So, because of the necessity for the minimum radius of bend consistent with the maximum in hardness, there has been a need for information as to the forming characteristics of these sheet metals in the various alloys, tempers and thicknesses. The literature yields relatively little regarding such forming characteristics, so that designers of apparatus and tools have been largely dependent upon past experience or tool tryouts for guidance. In presenting tabular data intended as a basis for selecting the temper of the metal and radius of the bend, we recognize the influence of many other factors which are not covered in this study. For example, the angle of the bend and conditions of the metal, such as grain size and presence of impurities, as well as conditions of the fabricating process, such as rate of forming and adjustment of the tools, may all affect the result. In addition, a bumping operation subsequent to forming, which is frequently used to set the bend, increases the strain on the metal. We wish to emphasize the fact that this is not considered a scientific investigation of the formability of materials or an attempt to correlate forming, characteristics with various other properties of the metals, except in so far as such properties are controlled by commercial limits on composition and temper.

Jan 1, 1931

By J. P. Hirth, C. S. Hartley

A simple graphical technique is presented for rapidly determining the ratio of resolved shear stress on slip systems in single crystals to the applied stress (Schmid factor) for various simple states of stress. Master plots are presented which, when used in conjunction with an appropriate stereo-graphic projection, allow one to determine the Schmid factor for all slip systems in a crystal of given orientation. It is shown that one such plot suffices for simple tension or compression, flex-ural bending, and biaxial compression, while a combination of two different plots must be used for torsion and simple shear. STUDIES of the deformation behavior of single crystals are most valuable when the applied stresses are resolved onto the various slip systems of the crystal. A careful study of the available slip systems and proper selection of the state of stress used and the specimen orientation can then yield quantitative information about the probability of specific dislocation reactions, the strength of barriers to plastic flow, and the mechanisms of yielding and flow in general. It is the purpose of this work to analyze some common states of stress used in deformation studies and to present a simplified way of determining for these cases the ratio of the resolved shear stress on the slip systems to the applied stress (Schmid factor). I) CALCULATIONS We first define two orthogonal coordinate systems: one based on the specimen geometry (a right circular cylinder of radius, R, is considered here) and one based on the particular slip system of interest. The unit vectors and angles specifying the two coordinate systems and the relationship between them are listed in Table I. The relationships among the various angles and unit vectors are shown on a stereographic projection in Fig. 1. The transformation matrix between the (XI X2 X3) and (x'1 x'2 x'3) system is x1 x2 x3 X'1 a11 al2 a13 x'2 a21 a22 a23 x'9 a31 a32 a33 where in this case the direction cosines aij are given by a11 a12 a13 aij = a21 a22 a23 a31 a32 a33 sin 0 cos F cos 0 sin F cos 9 = -cos 0 cos F sin 0 sin F sin 6 [1] 0 -sin F cos (p In terms of Eq. [I.], the stresses sij, referred to the slip system, are determined from oij, referred to the specimen axes, by1,2

Jan 1, 1965

Grade control aims to deliver quality tonnes to the mill via accurate definition of ore and waste. It comprises data collection and interpretation; local reserve estimation; supervision of development and mining; and stockpile management. The foundation of all grade control programs should be that of high quality sampling supported by geology. The requirement for quality grade control samples has long been recognised, where they should be representative, unbiased, safe and operationally timely. Underground sampling methods include chip and channel samples; grab samples; and drill-based samples. To achieve quality samples, collection techniques employed should minimise delimitation, extraction and preparation errors. Grade control staff should be well-trained and motivated, and mining staff should understand the need for grade control. This paper reviews grade control sampling methods and presents recommendations for best practice and minimisation of sampling errors.

Mar 1, 2010

By H. R. Pierce

A gas well has a certain definite capacity to deliver gas from the gas sand through the producing string of pipe. This capacity depends upon the pressures in the sand; that is, a well will deliver gas at a rate of flow which is determined by the formation or "shut-inn pressure in the sand and the back pressure at the face of the sand in the well. The three factors, rate of flow, formation or "shut-in" pressure, and the back pressure, for a given well, can be written into a fundamental relation which is strictly applicable only to that well. This relation can be used to determine the capacity of the well to deliver gas from any formation pressure against any back pressure held at the f ace of the sand in the well. Studies have been made of the deliveries of 400 gas wells operating under different conditions of pressure, Most of the wells which have been studied are in Osage County, Okla.; however, several representative studies have been made on wells in southern Louisiana, southern Texas, the Texas Panhandle, and West Virginia.

Jan 1, 1929

By B. P. Atkin, D. W. Brown

The handleability monitor has been specifically designed to provide a simple, rapid and on-site assessment of the whole or part consignment of a coal blend in its ‘as-received’ condition. Evaluation has been carried out at a number of coal-handling plants, on both metallurgical and power station coals from a variety of sources world-wide. The results which are used to predict which coals could routinely pass through a handling plant at line capacity, without causing blockage or delay, have also been correlated with moisture, ash and size analyses of the coal to develop a predictive model of handleability.

Jan 1, 2000

By Joseph A. Olmstead

Literature concerned with management and supervisory training was reviewed and analyzed from the perspective of relative effectiveness of various training methods for improving knowledge and awareness, changing attitudes, improving problem solving skills, improving interpersonal skills, and improving on-the-job performance. Conclusions were drawn relative to each method and the current state of the field of management and leadership training. A 168 item annotated bibliography is presented.

Jan 1, 1980

By H. I. Aaronson

The nucleation of pearlite at proeutectoid ferrite is inhibited, to an increasing extent, at the following locations: At twin boundary-nucleated ferrite, between closely spaced ferrite sideplates, and at intragranular plates. These effects are discussed in terms of the influence of transformation strain energies and of the interfacial free energy of austen-ite:ferrite boundaries on the rate of pearlite nucleation. The growth of pearlite into the interiors of austenite grains from the region of the grain boundaries is markedly restricted when low reaction temperatures and large austenite grain sizes permit the development of interlocking networks of intragranular ferrite plates. PREVIOUS investigators have made extensive studies of the interactions which occur between the proeutectoid ferrite and the pearlite reactions from the viewpoint of the mechanisms through which pearlite interferes with the nucleation and growth of proeutectoid ferrite.1-3 In the present investigation, the processes through which proeutectoid ferrite (hereafter termed simply "ferrite") can reduce the rate of formation of pearlite have been explored in some detail. A steel with a relatively low carbon content, in which the ferrite reaction can compete successfully with the pearlite reaction over a wide range of reaction temperature, and exceptionally coarse-grained specimens, which further emphasize the role of the ferrite reaction, have been employed for most of this work. A brief examination also has been made, however, of the effects of smaller austenite grain sizes upon these processes. Experimental Procedure The steel employed had the following composition: 0.29 pet C, 0.76 pet Mn, 0.25 pet si, 0,007 pet S, and 0.005 pct P. This alloy was homogenized for 48 hr at 1250°C. The investigation was performed

Jan 1, 1959

By Leslie S. Halasz

This paper describes the techniques implemented at Randfontein Estates to develop twin-haulages at 'high speed'. An operation which culminated in the world record advance for twin-end multiblast cyclic development in hard abrasive quartzites. A major expansion project was planned for the mine, with the sinking of a third twin-shaft system (to be known as Cooke No. 3), to raise the level of ore production from 3 500 000 to 5 000 000 tonnes per alumm. Subsequent redesign of the proposed shaft system as a single 9 m brattice wall shaft took place, reducing the planned shaft sinking period by 12 months and saving an estimated R 250 000 (U.S. $ 330 000) in sinking costs. The advancement of the Cooke No. 3 Shaft sinking and development programme necessitated a rapid excavation schedule for two interconnecting twin-haulages from the existing Cooke No. 2 twin shaft complex to provide a second means of egress. An early holing between the two shafts would provide significant financial and technical benefits. Pre-development and equipping of shaft pillar excavations would enable a rapid shaft production build up and blocking out of at least one year's ore-reserves.

Jan 1, 1983

By L. E. Schultze

Experiments were conducted by the U.S. Bureau of Mines to verify enhancements due to chloride and surfactant additions in the leaching system of chalcopyrite with ferric sulfate and sulfuric acid. A statistical experimental design was used and equipment was designed to eliminate contributions from changes in solution electrochemical potential during the course of the measurements. Results confirmed that chloride additions increased chalcopyrite leaching by as much as 94 pct over the electrochemical potential versus hydrogen electrode range of 630 to 750 mV at pH 1.7 and 50°C. Total iron concentration had no effect over the range of 1 to 5 g/L. The effect of surfactant addition was less well defined. While additions of LA 790 (a polyoxyethylene lauryl ether) resulted in increased copper leaching in several of the tests, the differences were too small to be statistically significant. No interaction effect could be verified.

Jan 1, 2010

By Shazad Hosein, William J. Birch, Robert Farnfield, David Jameson, Catherine E. Johnson

The current and consented quarry workings at a slate quarry in North Wales {UK} intersect old long abandoned underground slate mine workings. The old underground slate mine contains the remains of World War II buildings used to house artworks to protect them from war damage. Over the past 20 years, there have been a number of roof falls in the old underground slate mine, which have damaged the buildings and make general access unsafe. From observation of the timing of these falls, they occurred in the mid 2000’s. The purpose of the exercise was to determine the possible relationship between blast vibrations experienced on the surface and those experienced on the roof of the abandoned mine caverns. Thus preventing the need to regularly monitor in the old mine workings. In order to achieve this, a rigorous geotechnical assessment of the stability of the caverns was undertaken by a fully qualified Geotechnical Engineer. Once it had been determined that it was safe to do so, 3 “MEMs based” blasting seismographs were attached to the roof, in accordance with the instruction of the geotechnical engineer. In addition, 8 “MEMs based” blasting seismographs were deployed at various locations on the surface. The trial blast comprised of 51 blastholes, with charges varying between 46kg [101lbs] and 124kg [273lbs] of bulk emulsion explosive. The blastholes were in 4 rows of holes. The blast was connected using shock tube 25ms, 33ms and 65ms delay period relay detonators. The minimum distances from the blast to the surface and underground monitoring points were 78.1m [256 ft] and 114 m [374 ft] respectively. The results from the three underground monitoring locations in terms of resultant peak particle velocity was 4.42 mm/s [0.174in/s], 3.47 mm/s [0.137in/s], and 4.69 mm/s [0.185in/s]. In line with previous research, it was determined that the underground results [when compared on a “like for like” basis in terms of scaled distance] were lower in amplitude than the surface results. In this case by a factor between 0.47 and 0.87, averaging 0.68.

Jan 21, 2025

By Russell Franks, W. O. Binder

In recent years a considerable tonnage of the 18 per cent chromium and 8 per cent nickel steels has been used in lightweight high-strength structures that must be resistant to deterioration under atmospheric conditions. These steels are austenitic in character and their strength can best be increased by cold-working. Although a marked increase in tensile strength is obtained, claims have been made that the cold-worked steels do not possess fully satisfactory elastic propertics. Under certain conditions, however, this has caused no great concern, because, as explained by Ragsdale,1,2 he cold-rolled steels have been widely applied for construction of lightweight, high-strength trains using spot welding for joining purposes. Ffield3 agrees that the ease with which thin sections of the cold-rolled 18-8 steels can be joined by spot welding is greatly in their favor, but that they would be more satisfactory if higher elastic properties and a higher modulus of elasticity could be obtained. He states that, as far as the mechanical properties are concerned, the straight chromium stainless steel is superior to the cold-worked 18-8 steel, and in order to illustrate, he prcsented the data of Fig. 1, which also give a stress-strain curve for a low-carbon 13 per cent Cr steel. Ffield† proposed that columbium-bearing or titanium-bearing cold-rolled 18-8 steels be given a heat-treatment (preferably for 1 hr.) in the range 400" to 600°C. to precipitate carbides in order to obtain better mechanical properties. Discussions by Sutton,4,5 de Ganahl,6,7,8 Krivobok and Lincoln,' Knerr,l0 and Thaden11 have given further information on the properties of the cold-rolled 18-8 steels compared with other materials used in lightweight, high-strength structures. These investigators and others point out that the ultimate tensile strength of the cold-rolled 18-8 steel can be increased to 200,000 lb. per sq. in. or higher; Krivobok et al. indicate that

Jan 1, 1940

By Russell Franks, W. O. Binder

In recent years a considerable tonnage of the 18 per cent chromium and 8 per cent nickel steels has been used in lightweight high-strength structures that must be resistant to deterioration under atmospheric conditions. These steels are austenitic in character and their strength can best be increased by cold-working. Although a marked increase in tensile strength is obtained, claims have been made that the cold-worked steels do not possess fully satisfactory elastic propertics. Under certain conditions, however, this has caused no great concern, because, as explained by Ragsdale,1,2 he cold-rolled steels have been widely applied for construction of lightweight, high-strength trains using spot welding for joining purposes. Ffield3 agrees that the ease with which thin sections of the cold-rolled 18-8 steels can be joined by spot welding is greatly in their favor, but that they would be more satisfactory if higher elastic properties and a higher modulus of elasticity could be obtained. He states that, as far as the mechanical properties are concerned, the straight chromium stainless steel is superior to the cold-worked 18-8 steel, and in order to illustrate, he prcsented the data of Fig. 1, which also give a stress-strain curve for a low-carbon 13 per cent Cr steel. Ffield† proposed that columbium-bearing or titanium-bearing cold-rolled 18-8 steels be given a heat-treatment (preferably for 1 hr.) in the range 400" to 600°C. to precipitate carbides in order to obtain better mechanical properties. Discussions by Sutton,4,5 de Ganahl,6,7,8 Krivobok and Lincoln,' Knerr,l0 and Thaden11 have given further information on the properties of the cold-rolled 18-8 steels compared with other materials used in lightweight, high-strength structures. These investigators and others point out that the ultimate tensile strength of the cold-rolled 18-8 steel can be increased to 200,000 lb. per sq. in. or higher; Krivobok et al. indicate that

Jan 1, 1940