Search Documents

By John J. Gilman

F many years it has been suspected that a correlation existed between pits produced by etching and the density of dislocations in crystals. In 1953, the interest in this correlation was greatly stimulated when Vogel et al' demonstrated a 1:l correlation between etch pits and dislocations in low angle grain boundaries of germanium. About two years ago, the author began attempts to produce etch pits at dislocation sites in zinc mono-crystals. These attempts met with success a year or so ago,' and since that time a survey has been made of the etch pit patterns that are associated with various modes of deformation in zinc monocrystals. Unfortunately, the etching technique that will be described is too delicate for use as an accurate quantitative tool. Nevertheless, it has been of considerable assistance in clarifying the structure of plastically deformed crystals. Technique Many attempts were made to produce etch pits in high purity zinc crystals. It was found that several techniques would produce surface grooves at grain boundaries that had misorientation angles greater than about l°, but no technique was successful for boundaries with smaller angles. Among the things that were tried were: electrolytic CrO, (both etching and polishing concentrations), HNO, in various water and alcohol solutions, dilute HC1, many 0-0,-Na,SO, solutions, Cr0,-HC1 solutions, picral, electrolytic Na,S,O,, and electrolytic NaOH and KOH. A few attempts to use cathodic sputtering and thermal etching were also made.

Jan 1, 1957

By J. H. Kempton, D. Atkins, W. Locke

The scrutiny given to model predictions of pit-lake water quality has focused attention on the uncertainty associated with long-term predictions. Although comparison of probabilistic predictive modeling of water quality in existing pit lakes suggest that short-term predictions can bracket most parameters, un¬certainties in wall-rock reactions and the stability of groundwater composition and climate remain unquantified This overview of the uncertainties associated with longer-term predictions is presented as support for those considering policy decisions that must be made in the absence of reliable estimates of future conditions.

Jan 1, 2000

By Paul Billingsley, Augustus Locke

Certain adequately developed mining districts give complete three-dimensional patterns of ore bodies as clusters rising from roots in basement rocks with details controlled by structure of cover rocks. Examples are Goodsprings, Tintic, Bisbee, Leadville, Hedley, Eureka, Ely and Goldfield. In these and others the controlling structures in both basement and cover rock are elements of the neighboring regional structure and have been produced by rock movements in harmony with continental adjustments, which are usually steep tear faults in basement and thrust crumples in cover. Invariably the structures and movements in the districts have long geologic history and result from intersecting or superimposed deformations of different ages. Salt Lake districts show intersecting Uinta and Cordilleran elements; Colorado districts show intersecting pre-Cambrian and Tertiary elements, and Bisbee shows Tertiary superimposed on fina1 Paleozoic folding. Thus the position of districts has been determined by the patterns of North American orogenic belts, which make crossroads in Rocky Mountains and blocks of superimposed deformation in Sierra Nevada, northwest Coastand Canadian Coast Ranges. Essential function of repeated deformation is to strengthen rock, as from shale to slate to schist to gneiss, and thus make it competent to carry channels to depth with or without addition of intrusives. The essence of a mining district is the presence of such competent rocks with long-lived, deep, penetrating breaks reopened to permit passage of heat and associated products from depths to surface. It is suggested that melts such as magmas; metamorphism up to and including granitization; alteration, such as orthoclase-quartz or quartz-sericite or garnet, and also mineralization, may all be by-products of such heat escape along channels made by tectonic forces at specific foci. Magnitudes of Districts (Fig. 1) Any synthesis of ore deposits must deal with comparable units. Ore deposits are innumerable, but great ore deposits, commercially important for a generation or more, are few. The bulk of metals has come from districts of the first and second magnitudes (over $1,000,000,000 and over $250,000,000, respectively), and of these the United States and adjacent provinces of Canada and Mexico contain only 28, of which 9 are first magnitude: Butte, Coeur d'Alene, Bingham, Bisbee, Sierra Gold, in the West; Tri-State, Southeast Missouri, Michigan copper, Sud-bury, in the East. Another 28 or 30 districts are of third magnitude (over $50,000,000).

Jan 1, 1941

By Augustus Locke, Paul Billingsley

Certain adequately developed mining districts give complete three-dimensional patterns of ore bodies as clusters rising from roots in basement rocks with details controlled by structure of cover rocks. Examples are Goodsprings, Tintic, Bisbee, Leadville, Hedley, Eureka, Ely and Goldfield. In these and others the controlling structures in both basement and cover rock are elements of the neighboring regional structure and have been produced by rock movements in harmony with continental adjustments, which are usually steep tear faults in basement and thrust crumples in cover. Invariably the structures and movements in the districts have long geologic history and result from intersecting or superimposed deformations of different ages. Salt Lake districts show intersecting Uinta and Cordilleran elements; Colorado districts show intersecting pre-Cambrian and Tertiary elements, and Bisbee shows Tertiary superimposed on fina1 Paleozoic folding. Thus the position of districts has been determined by the patterns of North American orogenic belts, which make crossroads in Rocky Mountains and blocks of superimposed deformation in Sierra Nevada, northwest Coastand Canadian Coast Ranges. Essential function of repeated deformation is to strengthen rock, as from shale to slate to schist to gneiss, and thus make it competent to carry channels to depth with or without addition of intrusives. The essence of a mining district is the presence of such competent rocks with long-lived, deep, penetrating breaks reopened to permit passage of heat and associated products from depths to surface. It is suggested that melts such as magmas; metamorphism up to and including granitization; alteration, such as orthoclase-quartz or quartz-sericite or garnet, and also mineralization, may all be by-products of such heat escape along channels made by tectonic forces at specific foci. Magnitudes of Districts (Fig. 1) Any synthesis of ore deposits must deal with comparable units. Ore deposits are innumerable, but great ore deposits, commercially important for a generation or more, are few. The bulk of metals has come from districts of the first and second magnitudes (over $1,000,000,000 and over $250,000,000, respectively), and of these the United States and adjacent provinces of Canada and Mexico contain only 28, of which 9 are first magnitude: Butte, Coeur d'Alene, Bingham, Bisbee, Sierra Gold, in the West; Tri-State, Southeast Missouri, Michigan copper, Sud-bury, in the East. Another 28 or 30 districts are of third magnitude (over $50,000,000).

Jan 1, 1941

By H. B. Hunter, F. G. Stone, F. J. Dunkerley

Introduction and Literature Survey This is the second in a series of papers coming from this laboratory on the correlation of the low temperature tensile properties of tin-binary alloys with microstructure. These engineering data and those of the previous paper1 were obtained as the initial part of a long-range program to determine the changes in the fundamental mechanical properties accompanying the beta to alpha phase change in tin and its binary alloys below 13.2°C. Since it appears now that the more fundamental studies will be delayed,* and since no summary of the low temperature properties of these tin-base white bearing alloys was found in the literature, it was decided to publish all the engineering data thus far obtained. Accordingly, the tensile properties of thirteen binary alloys containing from 0.1 to 60 pet cadmium and 0.1 to 10.43 pet antimony measured at six temperatures from —196 to +23°C are presented here and their variations rationalized in terms of microstructure. A literature search showed that these systems had not been investigated at low temperatures, although both the tin-cadmium and tin-antimony2,3,4,5 and the tin-rich corner of the ternary system67 have been studied at room temperature. Hanson and Pell-Wal-pole5 and Homer and Plummer4 determined the tensile properties of alloys containing from 0 to 10 pet cadmium. The same authors3 determined the tensile strength and elongation in the tin-antimony system from 2 to 18 pet antimony at room temperature while Pell-Walpole et al.6,7 studied the properties of high tin and tin-antimony-cadmium alloys. Since there were many variables besides composition in these tests, it was difficult to make a valid comparison with the room temperature data of the present study, but in general the tensile strength and ductility values are in reasonable agreement. Pell-Walpole2 also determined the effect of grain size on the tensile strength of pure tin and 1 pet alloys of both antimony and cadmium. The true maximum stress was found to decrease exponentially as the number of grains in the cross-section increased. This effect of grain size was strikingly revealed in the present work, as indicated in a later section. Hanson and Pell-Walpole8 placed the solid solubility limit of antimony in tin at 3.5 pet at 20°C, increasing to 4 pet at 190°C, and then sharply increasing to 10.3 pet at 246°C (the latter being a peritectic point). Their results are in disagreement with those of previous investigators,9 and the discrepancy seems to lie in the micro-graphic observation of the second phase

Jan 1, 1950

By H. N. Thomson

GENERAL. THE Tooele plant of the International Smelting & Refining Co. is situated at the mouth of Pine canyon, Tooele county, Utah. It is connected with the main line of the San Pedro, Los Angeles & Salt Lake railroad by the Tooele Valley railway, and is about 7 miles from Tooele Junction. Fig. 1 is a general view of the plant. FIG. 1.-TOOELE PLANT OF THE INTERNATIONAL SMELTING & REFINING Co. The copper plant has been in operation since July, 1910, and the first blast furnace at the lead plant was blown in on Feb. 29, 1912. The location of the plant was selected on sloping ground with the idea of using gravity to the fullest extent and thus keeping labor at a minimum. Practically the entire plant is constructed of steel, reinforced concrete, and brick. Bingham ores, both lead and copper, are received over the Utah Consolidated Aerial Tramway. The tram buckets, each containing

Jan 7, 1913

By M. J. H. Ruscoe

"The circulation wear rates of pure nickel, cupronickel and nickel-plated-steel coins were measured and found to be in the ratio 1:3:1 . The relative wear rates of nickel and cupronickel coins were similar to those reported in earlier studies, and the circulation wear data for nickel were used as a reference in laboratory wear tests. A correlation between circulation wear rates and laboratory wear rates formed the basis for a prediction of service life using relief legibility as an 'end of life' criterion. This criterion was determined to be an average surface thickness loss of 12 um. The surf aces of nickel and Nickel-Banded-Steel (N-B-STM) coins were observed to harden both in circulation and in the laboratory tests at a rate of approximately I VHN/year of actual or simulated service life. It was also observed that the laboratory wear rate of N-B -S coins increased as nickel cladding thickness increased and this effect was attributed to differences in surface hardness.Wear test results are also reported for the new Canadian dollar coin material which shows a better wear resistance than pure nickel. IntroductionThe subject of coinage wear has a long history, and a number of studies have been published, concerned both with the measurement of circulation wear rates and with accelerated laboratory tests to simulate the behaviour of coinage materials in service. As early as 1803, wear tests were conducted by Hatchett on gold coinage using various types of vibratory and tumbling machines». These tests were commissioned by King George III of England who was concerned about the wear of gold coins in circulation.Early in this century, Adrian performed laboratory tests that showed that the wear rates of cupronickel 75/25 and nickel coins were in the ratio 3:1 and this ratio was later confirmed in laboratory tests reported by Daeppen and Zurrerw, The latter authors also weighed cupronickel and nickel coins that had been in circulation for various times and observed the same 3: I ratio. There was further support from Tylczak and Blickensderfer who reported significantly higher abrasive wear rates for cupronickel compared to nickel, when rubbed against sand paper."

Jan 1, 1988

By Robert L. Llewellyn

Preparation of coal begins at the face in underground mines or in the pit with surface mines. Impurities in raw coal can be in the seam itself or in extraneous material taken in mining from the roof or bottom. Raw coal is prepared only to the extent that is necessary to make the product salable. Over 60% of all coal production is processed to some extent in cleaning plants. For underground mines the proportion cleaned is 72% as compared to 42% from surface and 15% from auger mines. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only as necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent and only incidently with mines shipping raw run-of-mine coal crushed to a top size of, usually, 2 to 4 in., with little, if any, other treatment. ECONOMICS OF COAL PREPARATION During the past decade, major changes have occurred affecting the market, profit, and long-rang planning of the coal industry. Mining companies have become "partners" with consumers at many new and some old mines, both for steam and metallurgical coals. Coal properties have become "assigned" tonnages at mutually agreed upon conditions and prices. Lower unit-train tariffs have been instrumental in helping coal markets to compete against oil and atomic energy. Cod prices for power plants are still on a Btu (British thermal unit) basis but with more emphasis on sulfur content. For metallurgical coal, the lower and medium volatile coals are in demand and the price rises, generally, as the volatile percentage is lower. Moisture affects the Btu value of coal almost the same as ash content, but dusty conditions during loading and unloading are no longer accept-

Jan 1, 1973

By D. Bienstock

The use of alkalized alumina in removing sulfur dioxide from a coal-combustion flue gas at 625° F was investigated on a pilot plant scale. The absorber was 26 feet long and 1.6 inches ED. Counter-current gas-solids flow at gas velocities of 8 to 15 ft/sec in the presence and absence of baffles, as well as solids entrainment at gas velocities of 20 to 23 ft/sec with solids recycle, were employed. The spent absorbent as regenerated as fixed bed with the reducing gases--reformed natural .7.7d hydrogen. Of absorption-regeneration were successful completed using the alkalized alumina rolled into spherical granules 10 to 16 mesh. There was no loss in activity of absorbent toward SO2 with a modest attrition equivalent to 0.l percent of the solids feed. Supporting studies were conducted on the effect of the sodium content in the absorbent, the composition of the reducing gas, thermal treatment to increase absorbent hardness, and removal of absorbed chlorine from the absorbent. A mathematical model was formulated to describe the removal of SO2 by alkalized aluminum from fixed and falling beds.

Jan 1, 1967

By Donald S. Colby

CARBON-BLACK shipments, which had declined in the latter art of 1953, remained low in 1954 until after settlement of the labor strike that occurred in the rubber industry in July and August. The production of new model automobiles in the last quarter of the year spurred the demand for rubber tires and consequently the demand for carbon black. Total shipments of 1,498 million pounds for the year were 4 percent below 1953.

Jan 1, 1958

By Richard J. Mainiero, Marcia L. Harris

The New York State Department of Transportation recently commenced highway widening and drainage improvement projects in Clarence and Amherst, NY. Drainage improvements including the installation of storm sewer lines required excavation to a depth of 2.5 m (8.2 ft). In September 2002, NYSDOT stopped further blasting when 800 ppm CO was detected in the basement of a house near the blasting site. At the insistence of NYSDOT, the general contractor developed a new blast plan with the assistance of an environmental consultant. The plan provided for the installation of multi-gas monitors in buildings of special concern and/or with basements and residential type CO monitors in all other buildings within 100m (330 ft) of the blast. The multi-gas monitors would be remotely monitored. The plan provided action levels which would ensure public safety. The blast design was also modified to allow for better venting of CO. Blasts were limited to 20 ft lengths. The overburden was to be removed from the rock and blasting mats put in place to prevent flyrock. Approximately twenty feet of trench adjacent to the blast was left open to allow ground movement and gas release. The use of CO monitors was effective to alert occupants of a building to the presence of CO. The most effective appeared to be the residential type CO alarms with digital readouts. They were simple and easy to use and allowed the public to participate in the process. False alarms were repeatedly received with the more sophisticated instrumentation. Residential type CO monitors are preferable to warn people near blast sites. More sophisticated instrumentation should be avoided unless personnel are experienced in its use. A general overview of the blasting and monitoring is presented and discussed. The use and effectiveness of residential type CO monitors and multi-gas monitors are discussed.

By K. K. Kershner

This report describes an investigation by the Bureau of Mines designed to provide background data for extending and improving the applications of chlorine metallurgy in extracting metals from ores. Optimum conditions are given tor chloridizing galena, sphalerite, and chalcocite by contact with chlorine gas. Petrographic and chemical analyses of the sulfides used in the experiments are listed. Graphs are furnished showing the extent of chloridization of each metal sulfide over the temperature range of the observations. In each case, the first tests were made with the reaction chamber at room temperature. This temperature was increased by regular increments in succeeding tests until the temperature was reached at which quantitative conversion of the sulfide to chloride was observed. The data are also plotted for screen-size fractions of the sulfide minerals investigated. Data show that the extent of metal chloride formation was affected by chloridization time, particle size of the sample, and usually, the temperature of the reaction chamber. At 300° to 400° C. an anomaly was noted for both galena and sphalerite. The temperature at which this anomaly was observed varied according to the particle size of the mineral. Comparisons are made between the chloridizing characteristics of the mineral sulfides and their chemically prepared counterparts.

Jan 1, 1961

By J. Bender

The objective of this research was to (1) Further develop cyanobacteria mats' for metal-tolerance and cold-tolerance, (2) test them for durability in the field environment and (3) assess them for metal sequestering potential with actual and simulated field samples. Results show that mats performed well In the field and effectively sequestered metals from actual and simulated field samples. Metal uptake from Iron Mountain Hine samples was for Ins 87%, Cu and Cd 99%, Initial concentrations (mg/L) were Zn = 3,250, Cu , 279, Cd = 28. In solutions simulating the Gulf Tunnel drainage, Zn and Mn were effectively removed by mats immobilized on glass wool. Effluent water, after treatment, generally had a Ph of 7 .5-8.5. Al though the final metal concentrations in the mats 'harvested from the decontaminated water were only 1% or less, the actual mechanism of metal deposit was probably a mat-mediated alteration of the environmental conditions causing the metals to deposit outside the mat as oxides or carbonates. Bioflocculents, released by the mats, were likely involved in the metal-removal process.

Jan 1, 1996

The continued exploration of the major brown coal deposits of the Latrobe Valley has resulted not only in the discovery of huge additional reserves, but also in new concepts of the stratigraphy and structure of the coal seams in that area. The author sets out his interpretation of the new information which has become available over the last six years.A section of the paper is devoted to the quality of the coal. As the chemical composition of these brown coals has been discussed in some detail by previous authors, only the major constituents and the heat value of the coal are dealt with in this paper. Some of the variations in quality are related to the geological structure.The occurrence of underground water and its relation to open cuts is dealt with briefly.INTRODUCTIONThe Latrobe Valley Tertiary Basin is almost entirely covered by a layer of Post Tertiary sediments which mask the underlying rocks and their structures. As a result, the geological understanding of this area has had to await the comprehensive drilling campaign in search of brown coal, initiated by the Victorian Mines Department in 1917, and subsequently carried on by the State Electricity Commission of Victoria. The first detailed geology was published by Herman (1922), and this was followed some 25 years later by papers by Edwards, and later Thomas and Baragwanath, to which reference will be made later in this paper. Herman included a section on the geology of the Latrobe Valley in his book Brown Coal, which was published in 1952.Since that time a considerable amount of new information has become available from the continued drilling carried out by the Commission. In addition, geophysical work carried out by the Commonwealth Bureau of Mineral Resources has assisted in the defining of geological structures in the area.

Jan 1, 1960

By G. E. McClelland

During the 1970?s, the Bureau of Mines investigated a particle agglomeration technique for improving the flow of leaching solution through heaps of clayey or crushed, low-grade gold-silver ores, wastes, and tailings. This technology has been adopted on a broad scale by the precious-metals-processing industry. This report presents information on five commercial operations that have benefited from agglomeration technology and that represent a cross section of current heap leaching practice. The technology is cost effective because of decreased leach times and improved precious metal recoveries.

Jan 1, 1983

By W. Jolley

Decarburized iron and Fe-3.28 pct Ni alloys were impact and tension tested in the temperature range of ambient to 4°K. It was found that alloying with nickel improves the fracture properties of the ferrite matrix. The improvement in toughness of iron alloyed with nickel is attributed to the effect of the nickel addition on the temperature and strain rate dependence of the yield stress as well as on slip behavior. The Fe-Ni alloy exhibits wavy slip when strained at temperatures down to at least 50°K. This behavior contrasts with that of the unalloyed iron where a change It is a generally accepted fact that of the common alloying elements of steel only nickel and manganese improve both the room-temperature yield strength and the notch impact properties. It has been argued for a number of years that manganese refines the ferrite grain size, the pearlite spacing, and the grain boundary carbides in medium- and low-carbon steels and thereby increases resistance to brittle fracture.''' This hypothesis recently was confirmed for a 0.04 pct C iron containing manganese, but at the same time from wavy to planar slip occurs at about 120°K. The observed lower temperature and strain rate dependence of the lower yield stress in the Fe-Ni alloy as compared to the unalloyed iron may be attributed to this difference in slip behavior. In contrast to suggestions published previously, transmission electron microscopy showed that the uniform dislocation distributions and the lack of dislocation tangles which are produced by low-temperature straining of bcc materials cannot be attributed to the absence of cross slip at these temperatures. no increase in notch toughness was observed in a decarburized Fe-Mn alloy.3 It thus appears that manganese only increases the toughness of Fe-Mn-C alloys by refining grain boundary carbides and has no toughening effect in carbon-free iron. On the other hand, the mechanism whereby nickel improves toughness has not been established. Hodge et a1.4 have clearly shown that a 3.28 pct Ni addition lowers the impact transition temperature of 0.02 pct C steel approximately 35°C when the grain size is maintained constant. Recently, Wullaert and Tetelman6 stated that nickel refined the grain boundary carbides of an Fe-C alloy and consequently increased the toughness. They also observed the previously reporteda-'

Jan 1, 1969

By Charles L. Kimbell

For a study such as this, which summarizes and amalgamates much information collected, compiled, and utilized by the numerous U.S. Bureau of Mines country specialists and branch chiefs for inclusion in the country and regional reports that comprise the five other sections of 1991 Minerals Yearbook-International Review, it is clearly impossible to cite all sources of information used in its presentation, but some recognition is due. Generally speaking, this study and its related detailed studies on countries and areas would be much more difficult, if not impossible, without the efforts of the personnel of national mining and geological agencies throughout the world. Information that they collect, compile, and then publish, either in their own volumes or those of central statistical agencies in their countries, are the foundations on which this work rests. Thus, appreciation is expressed to the multitude of persons employed by these agencies.

Jan 1, 1993

By N Herault

PT Freeport Indonesia recently completed preproduction development and construction of the Big Gossan underground copper and gold mine, located in the Ertsberg mining district of Papua, Indonesia. Production has commenced with an expected ramp-up to full production of 7000 tonnes per day in 2012. The Big Gossan utilises an open stoping mine method with paste backfill.In order to deliver ore to the mill, which sits in a valley above the ore deposit, an underground production shaft and hoisting facility was designed and constructed as the key component of ore haulage. The design and construction of the Big Gossan shaft posed many challenges to the project team. Available shaft design and construction expertise were limited as this was the first shaft of its kind in Indonesia and the project was undertaken during a time of high industry demand for new shaft systems. Construction resources were also limited due to the remote location and competition with existing, producing mines for these resources and skills. The project also taxed the ability of Freeport to provide services and resources to this as well as their other projects.Completion of the Big Gossan shaft was a milestone in PT Freeport Indonesia’s plan to fully transition ore production to the underground environment in this decade.This paper deals with the various challenges faced by PT Freeport Indonesia and shaft contractor, PT Redpath Indonesia, during the construction of the Big Gossan shaft and offers suggestions to improve future shaft projects of a similar nature.

Mar 21, 2011

By JO. E. SHERID

THE Dawson coal-mines are owned and operated by the Stag Canon Fuel Co., of which Dr. James Douglas is President and E. L. Carpenter general manager. The property is situated in Colfax county, N. M., and the openings now in operation are in townships 28 and 29 N. R. 20 E., and township 28 N. R. 21 E., shown in Fig. 1. The mines are part of the southern end of the Raton coal-field, which extends north into Colorado and embraces many coal-camps of the Trinidad section. II. GEOLOGY. Geologically, the coal-measures, commonly known as the Laranmie series of the Cretaceous system, have a thickness of about 800 ft. in the vicinity of Dawson. The coal makes an excellent coke, and, according to some authorities, its coking properties are clue to the action of intruded sheets and sills of igneous rock, the sheets occasionally thickening into masses resembling laccoliths, at such places making nearer approach to the coal and sometimes producing small areas of natural coke. There are but few dikes through¬out the entire southern portion of the field and little or no faulting along the dikes. In some parts of this great coal-field the intrusive sheets are far removed in the green shales below the coal-measures, and are so much altered as to be difficult of identification. There is but little disturbance of the strata through¬out the Raton coal-field in as far as it extends into New Mexico. There are two workable seams in the coal-measures, and two or three smaller coal-seams, ranging from 1 to 2.5 ft. in thick-

Jun 1, 1909

By W. L. Fink, R. S. Archer

This paper describes results obtained on aluminum-beryllium alloys and aluminum-beryllium-copper alloys in the preparation of which aluminum of 99.95 per cent. purity was used. The constitution and structure of the high purity binary alloys are given. The aluminum-beryllium eutectic occurs at 0.87 per cent. beryllium and 645° C. The solid solubility of beryllium in aluminum at 631° C. is 0.05 per cent, beryllium, and at room temperature is less than 0.013 per cent. beryllium. The densities of the alloys are substantially the same as the values calculated on the assumption that the densities of the elements are not changed by alloying. All of the alloys age-harden at room temperature after a solution heat treatment, and the chill cast aluminum-beryllium-copper alloys age-harden at room temperature without a prior solution heat treatment. Hardness and tensile properties are given. Salt spray corrosion tests on sheet specimens are described. It is shown that beryllium docs not lower the corrosion resistance of aluminum to salt spray provided the alloy has received a solution heat treatment. Commercial Possibilities of Beryllium Alloys Beryllium has certain properties such as low density, high hardness, good corrosion resistance, low thermal expansion and fairly good electrical conductivity, which would indicate that it is worthy of consideration as an ingredient of light alloys. It was not until recently, however, that beryllium could be produced with sufficient ease to encourage research along this line. The production of beryllium by electrolysis from a fluoride bath has now developed to the stage where it could be used commercially if there were sufficient demand for the element. Claims made in certain newspapers and technical articles in regard to thc strength and corrosion resistance of thc aluminum-beryllium alloys are not justified by experimental results. Moreover, beryllium is an expensive metal ($200 a pound at the time this work was done) and, on account of the nature of its ore and the consequent difficulty of its extraction, it will in all probability continue to be a relatively expensive metal, although the cost would undoubtedly be a great deal less than $200 a