Search Documents

By Bjørn Nilsen, Brian J. Ballou

The Tellnes open pit mine in Southwestern Norway has been operating since 1960. The maximum height of pit walls is currently about 150 meters with the current mine plan extending this distance to 400 meters with slope stability being a major controlling factor. As a result of unfavorable combinations of directions of major joints and faults, local stability problems have occurred several places in the pits walls. Stability problems have affected the reliability of main transport roads on several occasions. Most of such incidents have occurred during heavy rainstorms and during periods of repeated freezing/thawing. This paper reviews some of the stability problems and the measures taken to deal with such stability problems.

Jan 1, 2006

By P. A. Riveros, J. Binvignat, V. M. McNamara, D. Koren

The recovery of cyanide from a gold mill solution containing high levels of copper (400 mg/L to 900 mg/L) using the AVR process was evaluated. It was determined that acidification to pH 2 to 3 provides a suitable balance between HCN generation, copper precipitation and acid consumption. A short pilot plant campaign showed that ~75% of the feed WAD cyanide was recovered while the remainder precipitated along with copper upon acidification. The acid consumption averaged 3.5 g H2SO4 per litre of solution. The copper precipitate, consisting mostly of CuCN and CuSCN, was readily separated from the solution by gravity. The volatilization of HCN in countercurrent packed columns averaged 98.7% efficiency. Reabsorption of HCN was practically 100% in NaOH solutions and slightly lower in a lime slurry. Basic volatilizer design parameters applicable to a large-scale operation were determined, including the Henry’s Law constant and the mass transfer coefficient of HCN gas.

Jan 1, 1998

By T. Grounds, K. Singh, W. R. Reed, R. Cross, G. Ross, S. Klima, M. Shahan

"A 2nd generation roof bolter canopy air curtain (CAC) design was tested by National Institute for Occupational Safety and Health (NIOSH) at a Midwestern underground coal mine. During the study, the roof bolter never operated downwind of the continuous miner. Using a combination of personal Data Rams (pDR) and gravimetric samplers, the dust control efficiency of the roof bolter CAC was ascertained. Performance evaluation was determined using three methods: (1) comparing roof bolter operator concentrations underneath the CAC to roof bolter concentrations outside the CAC, (2) comparing roof bolter operator concentrations underneath the CAC to the concentrations at the rear of the bolter, and finally, (3) using the gravimetric data directly underneath the CAC to correct roof bolter operator concentrations underneath the CAC and comparing them to the concentrations at the rear of the bolter. Method 1 dust control efficiencies ranged from -53.9% to 60.4%. Method 2 efficiencies ranged from -150.5% to 52.2%, and Method 3 efficiencies ranged from 40.7% to 91%. Reasons for negative and low dust control efficiencies are provided in this paper and include: incorrect sampling locations, large distance between CAC and operator, and contamination of intake air from line curtain. Low dust concentrations encountered during the testing made it difficult to discern whether differences in concentrations were due to the CAC or due to variances inherent in experimental dust measurement. However, the analyses, especially the Method 3 analysis, show that the CAC can be an effective dust control device. INTRODUCTION Canopy air curtains (CAC) have been shown to be an effective respirable coal mine dust control for roof bolters in a laboratory setting with dust control efficiencies ranging from 14% up to 75% [Goodman and Organiscak 2001, Listak and Beck 2012, Reed et al. 2017]. Unfortunately, there is limited information on their effectiveness for controlling respirable coal mine dust in the field. On continuous miners, CAC dust control efficiencies ranged from 23% to 69% [Krisko 1975]. Two underground tests of the CAC on roof bolters demonstrated dust control efficiencies of 35% and 53% [Listak and Beck 2012] before problems occurred with operation of the CAC. Since the implementation of the new respirable coal mine dust limit from 2.0 mg/m3 to 1.5 mg/m3 (Code of Federal Regulations, 30 CFR 70.100, 2015), roof bolter CACs are becoming more commonplace in underground coal mines as a dust control tool to prevent roof bolter operator overexposure to respirable coal mine dust. J.H. Fletcher & Co. has been instrumental in delivering an effective design which incorporates the filter, blower, and canopy plenum seamlessly into the design of the roof bolter, resulting in a successful operational roof bolter CAC."

Jan 1, 2018

By Garfield Schnee

MACHINERY has not taken the place of manual labor in steep pitch coal in the anthracite field and there is a shortage of miners experienced in this type of work. To overcome these difficulties several coal companies have resorted to different types of mining such as the diamond or zig-zag method, the slant method, long hole drilling, and several other variations. For the past 5 years the diamond shape method has been used extensively in the heavy pitching beds of both the Knickerbocker and Yatesville basins at Knickerbocker colliery of the Philadelphia & Reading Coal & Iron Co.

Jan 10, 1950

By AIME AIME

BEGINNING Thursday, July 16, the National Broadcasting Co. is broadcasting from 6:30 to 6:45 p.m., over its nationwide network and possibly also by short wave a series of eleven radio programs dealing with the contributions of engineers to the prosecution of the war. The series is being arranged and sponsored by a committee of representatives of the national engineering societies, R. L. Sackett, chairman. The committee began its deliberations before Pearl Harbor and had scripts under way on blackouts, bombs, and damage to structures. The declaration of war emphasized the importance of the proposed radio program. The National Broadcasting Co. and the Office of Civilian Defense enthusiastically endorsed the committee's proposal and have been generous in their help and approval of scripts so far submitted. Controversial matters are included in the broadcasts and changes will be made when requested by O.C.D. up to the minute that a program goes on the air. In this way the latest and authoritative information will be given.

Jan 1, 1942

By E Giles

Pike River Coal Limited (PRCL) is opening a new underground coal mine in the Paparoa Ranges north-east of Greymouth. To access the coal reserves, PRCL have had to build a 13 km access road through regrowth and virgin forest, and appointed McConnell Dowell Constructors Limited, with URS New Zealand Limited as their consulting engineers, to construct the final access link: a 2.3 km long, 5.5 m wide and 4.5 m high incline tunnel. This paper discusses the logistical issues of construction in an isolated pristine forest in mountain land and how they were addressed. It provides an overview of the 90 per cent complete tunnel and how challenging rock conditions have been mastered. It outlines briefly the remaining work which is construction of pit bottom workings where the mine infrastructure will be housed and construction of a 110 m deep, 4.0 m diameter, vertical ventilation shaft.

Jan 1, 2008

Coal Division Industrial Minerals Division Minerals Beneficiation Division Mining, Geology and Geophysics Division Council Will Mitchell, Jr, Chairman (MBD), Kenneth L Cook, Vice-Chairman (MGGD). Edward L Clark (MGGD), Raymond B Ladoo (Ind Min Div), Sandford S Cole (Ind Mm Div), Norman L Weiss (MBD), C T Hayden (Coal), H F Yancey (Coal), Clayton G Ball (MED), P De Bruyn (MIED), Arnold Buzzalini, Secretary, AIME, 29 West 39th Street, New York 18, N Y Mining Branch Advisory Committee Will Mitchell, Jr, Chairman, Grover J Holt, J B Morrow, J L Gillson, Edward G Fox, S S Cole, Roger V Pierce, Norman L Weiss. H C Weed. J R Van Pelt

Jan 1, 1956

By H. William Zeller

The Bureau of Mines performed laboratory research into the effects of a barium-based fuel additive (the "postflame" type) on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of types certifiable for use in underground mines. Test parameters consisted of additive concentration and engine loads, speed, and air intake restriction. DPM emissions, including condensed volatiles, were measured gravimetrically. Also measured were gaseous emissions including carbon monoxide, nitrogen oxides, and hydrocarbons. The fuel additive was effective, reducing DPM up to 75 pct, when used at a concentration of 0.09 wt pct (one-fourth of the concentration recommended by the manufacturer). The additive was most effective at the highest fuel-air ratios, reducing DPM from 400 mg/m3 for untreated fuel to 120 mg/m3. At light loads, 25 pct of full rated, no DPM reductions were measured. Based on these results, the additive is recommended for use in diesel fuel, at a concentration of 0.09 wt pct, to power underground mining equipment as long as certain conditions are met: that a beneficial DPM reduction is verified, that the minimum required quantity of additive is used, and that potential adverse effects such as increased nitrogen oxides are checked.

Jan 1, 1990

By Kang-In Rhee

Nonferrous metal recycling not only provides energy saving and environmental benefits but also is a significant factor in the supply of various types of metals used in our society. Recycling plays an important role in establishing the sustainability of materials. The total amount of recycled nonferrous metals by weight accounts for less than 5% but their value is larger than 50% compared to ferrous metal recycling which consists of about half of the total metal recycling in weight. This paper describes trends and typical achievements in nonferrous metal recycling and overviews the present and future of nonferrous metal recycling technology and business in Korea.

Jan 1, 2006

By J. H. Fowler

Canada's gypsum industry began over two hundred years ago in the Maritime Provinces when farmers attempted to supplement their incomes by selling "land plaster" to traders bound for the United States. Rising from such humble beginnings, gypsum now contributes significantly to the economies of nine of Canada's ten provinces. Thirteen open-pit and three underground mines produced a total of 8.38 million tonnes of crude gypsum and seventeen processing plants manufactured 2.49 million tonnes of finished products in 1985. Recent economic growth in North America has resulted in steady increases in gypsum production, however, competition from foreign producers and by-product gypsum poses a growing threat to Canada's gypsum mining industry.

Jan 1, 1987

By David S. Brown

What troubles me so often about debates over the environment, which I have heard since I entered government in the late 1960's, is that the issues are so often presented as a false dilemma--the either-or fallacy in logic. The either-or fallacy allows only two possible choices: Either protect the environment or exploit it. In reality, however, there may be a few more options. The diverse, often competing, values that the Earth offers require us to weigh and balance those options through a range of policy options. A quality environment and economic growth and opportunity are not mutually exclusive. First, let me acknowledge that I support a set of resource values recognized in U.S. laws and deemed important down through history for the success of free, progressive, and secure societies: the importance of access to raw materials. Increasingly, however, mineral raw materials have been viewed at best as not particularly relevant to a sophisticated, technologic society, and at worst monstrously destructive of our natural environment. Both perceptions, in my judgment, are wrong.

Jan 1, 1989

By Gerald A. Muson, Fremont F. Clarke

"INTRODUCTION The use of scrap mica as an industrial raw material has grown rapidly during the past two decades. Demands by various industries for ground mica for use in the roofing, paint, rubber, plastics, and wallpaper trades as well as for less extensive uses in insulation, oil-well drilling, welding, pipeline enamel, decorative material, and for other purposes exceed present (1947) supplies.A small proportion of the raw material used comes from the Black Hills of South Dakota, where casual recovery has been practiced in the exploitation of pegnatite deposits for more valuable minerals. The annual production of scrap mica in the Black Hills for the years 1939 to 1946 is shown in figure 19. 4/Although small, this production of scrap mica materially augments the incomes of numerous operators.Volume production of mica would offer attractive opportunities for obtaining steady and more economical supplies of the rare minerals as byproducts. Appreciable supplies of beryl, lithia minerals, sheet mica, tantalite-columbite, and cassiterite could accrue. Furthermore, a stable scrap-mica production would complement the production of quality feldspar, for which the Black Hills pegmatites are noted, and would help balance the economy of pegmatite mineral production.Mechanical methods of separation are requisite to production of enough scrap mica to be generally profitable. Various phases of the characteristics end treatment of mica have been investigated by the Bureau of Mines. A bibliography of these reports is appended.In 1945 the Bureau of Mines conducted pilot-plant tests to recover scrap mica by selective screening of crushed pegmatite. More recently the problem has boon studied in the Pegmatite Research Laboratory to aid in developing technological methods by which scrap mica may be separated from crushed pegmatite."

Feb 1, 1949

By E. S. Machlin

The possibility that formation of voids under creep-rupture conditions may take place by the condensation of vacancies has been investigated theoretically. It has been concluded that nucleation of voids under creep-rupture conditions by vacancy condensation is highly improbable. However, growth of pre-existant voids by vacancy condensation is probable. A number of predictions made in this theory have been verified by the data. It has been predicted and checked that the product of rupture life and steady-state creep rate for preannealed metals and single phase alloys is an approximately invariant quantity, independent of stress, temperature, and atomic number for a given type structure. The direction of the effect of cold work on this product has been predicted and found in agreement with experiment. A number of experiments to evaluate the vacancy condensation mechanism further are described. SEVERAL papers have appeared recently which speculate on the origin of voids formed at grain boundaries under stress.' ' The object of this paper is to examine quantitatively the proposition that the voids produced in a creep test are a result of vacancy condensation. A result of this paper is a theory of creep-rupture. Void Nucleation Application of standard nucleation theory" to the problem of void nucleation leads to the following conclusions: 1—Homogeneous nucleation of voids requires a supersaturation ratio (concentration of vacancies in supersaturated to that in saturated solution) of 400 for a reasonable surface energy of 1000 erg per cm-and 1.4 for the improbably low surface energy of 10 erg per cm. 2—Heterogeneous nucleation of voids at plane interfaces between two phases requires a supersaturation ratio of 2.5 for a typical contact angle of 145 3-—Void nucleation about a solid particle may be accomplished at a supersaturation ratio of 1.17 for a typical value of work of adhesion? of 60 erg per The work of adhesion is the surface work 10 replace two solid-vauor surfaces by a solid-solid interface. enr ' between an oxide and a metal in the presence of a surface active element such as sulphur. Estimates of the supersaturation ratio at which voids are produced in diffusion experiments yield a maximum of 1.01. Inasmuch as the foregoing mechanisms of void nucleation probably will not operate at this level—too low a surface energy is required—the investigatol. is led to the conclusion that voids must already exist. That is, nucleation of voids probably does not occur. Rather, existing submicroscopic voids grow out to visible size. Already existing voids might be produced during solidification or working. Supercritical sized parlicles which contain cracks may act as heterogeneous void nuclei. Gas pockets may act as void nuclei. Experiments are desired to determine the nature of the heterogeneous void nuclei which grow out to voids in both diffusion and creep experiments. Void Growth Void growth might occur in at least two possible ways, depending upon whether the already existing void nuclei are at grain boundaries or within the grains. In the case of a spherical void far from a crystal boundary, vacancies are generated during creep as a consequence of the migration of suitable dislocation jogs' and are also annihilated at sinks. Under these conditions, a steady-state concentration of vacancies is built up in the crystal, defined by the condition that for any differential volume the rate of generation of vacancies in that volume equals the rate of annihilation of those vacancies." This equality would lead to the development of a gradient of vacancy concentration radially outward from the void surface up to a radius where the vacancy lifetime becomes equal for all directions of vacancy migration. The distance over which this vacancy concentration gradient extends equals about 2vD,T* where D, is the vacancy diffusivity and T:' the vacancy lifetime in a crystal outside the gradient in a zone of constant vacancy concentration. The vacancies generated in the region over which the gradient exists will annihilate more often at the void than elsewhere. Approximately a little over one-half the vacancies generated in the gradient zone will annihilate at the void. Hence, the growth rate of the void is given by on where R is the radius of void in centimeters, is the atomic volume, and R is the rate of generation of vacancies, number per centimeter" per second. R D and T* may be estimated in terms of other physical parameters." In particular, R = n.j e/b [3] where n is the average number of vacancy produc-

Jan 1, 1957

By Nikkam Suresh

Dense medium cyclones have been in use for washing coarse and small coals for more than 50 years. There have been modifications in its design and today these units have become indispensable for washing of Indian coals possessing difficult washing characteristics. About 53 percent of the Indian coals (coking and non-coking) are being washed in jigs, about 38 per cent are washed in dense medium cyclones while the remaining 9 per cent is treated in other units like Barrel Washers, Heavy Media Baths and Drum Separators etc. The present paper deals with the attempts made for design of industrial Dense Medium Cyclones for enhanced coal recovery. Two industrial units of 500 mm diameter and 650 mm diameter were designed with their washing capacities being 200 m3/hr and 350 m3/hr, respectively. The results of the pilot tests conducted on 500 mm cyclone treating very high Near Gravity Material coals crushed to -3.0+0.5 mm gave an ash reduction of up to 19.5 percent with the new design i.e., from a feed ash of 34.5 percent to 15.06 percent in clean coal with an appreciable yield of 45 percent in one stage.

Sep 1, 2012

By Kang-In Rhee

Nonferrous metal recycling not only provides energy saving and environmental benefits but also is a significant factor in the supply of various types of metals used in our society. Recycling plays an important role in establishing the sustainability of materials. The total amount of recycled nonferrous metals by weight accounts for less than 5% but their value is larger than 50% compared to ferrous metal recycling which consists of about half of the total metal recycling in weight. This paper describes trends and typical achievements in nonferrous metal recycling and overviews the present and future of nonferrous metal recycling technology and business in Korea.

Jan 1, 2006

By E. L. Horner

"Srnoky River Coal is capable ofprocessing 3 million tonnes per year ofrun-of-mine coal at the Smoky River Coal preparation facilities to produce 2.1 million tonnes of high quality, low volatile coking coal for export markets. Multi-seam surface and underground mining operations are scheduled to maintain raw coal feed to the plant. Two beneficiating circuits wash the coal. A heavy medium cyclone circuit cleans the plus 0.5 mm coal and a froth flotation circuit cleans the minus 0.5 mm coal. Clean coal is thermally dried, loaded into unit trains, treated for dust suppression, and transported to west coast port facilitiesf or export. Plant by-products are used as thermal fuel Jn an adjacent power station. Quality control procedures ensure efficient resource recovery for a yield of uniform specification product, at a 7% ash level. Introduction Smoky River Coal operates surface and underground mines in the Smoky River coalfield. Approximately 3 million tonnes per year (mt/ a) of run-of-mine (ROM) coal can be processed at the coal preparation plant to provide 2.1 mt/ a of clean, high quality, low volatile bituminous coking coal. Coal is processed by heavy media and froth flotation cleaning circuits and is thermally dried.Raw Coal Characteristics The characteristics of the ROM coal, both in terms of quality and size consistency, vary with intrinsic seam qualities and mining methods employed. The two seams mined (No. 4 and No. 10) show distinctly different washability characteristics. Seam No. 4 contains relatively few middlings and can be readily cleaned by dense-medium cyclones and froth flotation to give a clean coal at specification ash content. Seam No. JO is more difficult to wash, and the ash content of the clean coal is higher than No. 4 seam at the same operating conditions. However, when the upper I m is excluded from the plant feed, the remaining lower section has washability characteristics similar to No. 4 seam. Coal mined by underground means sometimes contains caprock and consequently tends to be dirtier than similar coal mined by surface means."

Jan 1, 1985

By C. J. Pritchard, A. B. Cecala

An evaluation was performed on a district recirculation system at a trona mine in Granger, WY. A 1.52 m-diam (5 ft-diam), 37.3-kW (50-hp) vane axial fan was installed in a crosscut between the intake and return airways and recirculated about 31.4 m3/s (66,578 cfm) of air back into the intake. This amounted to a recirculation factor of about 20% of the return air. This air was part of the primary ventilation to three different continuous miner sections at operating distances of between 610 m (2000 ft) and 1829,m (6000 ft) from the recirculation fan. The mine environment was constantly monitored for respirable dust, methane and carbon monoxide in the operating sections and in the main intake and return entries. In addition, air samples were taken with and without the recirculation system during the evaluation and analyzed using gas chromatography. The results of this study showed only small increases in dust, while all other mine contaminants remained at such low levels that it was impossible to determine any relative changes from the recirculation system. Because of this, a brief SF6 tracer gas analysis study was subsequently performed to more precisely determine an increase in a mine contaminant with the recirculation system.

Jan 1, 1992

Remarks Of Mr. Robert W. Hunt, General Superintendent, Albany And Rensselaer Iron And Steel Company., Troy N. Y. - In discussing Dr. Dudley's two most interesting papers, I feel a natural hesitancy in disagreeing with conclusions formed after such careful and conscientious work. But I think he has made his deductions from too meagre premises. The analyses of but twenty-five samples are entirely too few to justify the establishment of so important a formula. When we consider that he indirectly proposes to regulate an interest amounting, even at the present low prices, to over $20,000,000 per annum, we may well hesitate before accepting a formula based upon the chemical and physical analyses of but twenty-five steel rails. Dr. Dudley touches the keynote in referring to the proposed labors of the Government Test Commission. They based their hopes of attaining success upon the chemical and physical analyses of a very large number of samples, and in the only branch of investigation which the short-sighted policy of Congress has allowed them to complete, i.e., chain cables, we find that a dozen, twenty-five or one hundred tests gave no satisfactory results. It was only after many hundreds that they were enabled to draw conclusions. There are so many circumstances bearing upon the life of a rail, that the task of extracting a correct result seems herculean. I presume I am right in stating that in our Northern latitudes early winter and spring months witness the breaking of the greatest number of rails, thus seeming to prove that an unstable road-bed has much to answer for. Then, again, broken and flattened wheels must be taken into account, but I am convinced that more rails have been broken by the treatment which they received before leaving the rolling-mill * The remarks of the participants in this debate have been written out by the speakers, and are here given without any attempt to retain the order of the dis¬cussion. While the report does not, therefore, preserve the vigor and spontaneity of the debate, it is believed that it gains in value by giving the matured views of the speakers. The continuation of this discussion at the Pittsburgh Meeting, May, 1879 (beginning with remarks of Mr. Cloud on page 401), is appended for convenience of reference.-T. M. D., Sec'y

Jan 1, 1879

By T. Wajima

"A novel carbonaceous adsorbent for recovery of nickel from nickel plating waste solution was prepared from rice straw using sulfur impregnation. The rice straws were cut to 1 cm pieces, and then immersed in 0.01 - 3 M K2S solution to prepare sulfur-immersed materials. The immersed-materials were heated at 100-700 ºC in nitrogen gas to produce the sulfur-impregnated carbonaceous adsorbent by pyrolysis. The contents of carbon and sulfur in the adsorbent and abilities of adsorbent to recovery nickel from aqueous solution were examined. The contents of carbon and sulfur in sulfur-immersed materials are almost same as those in raw material. In pyrolysis, with increasing the heating temperature to 200 ºC, the contents of carbon and sulfur are almost constant, and then above 300 ºC those increase. The recovery for nickel using raw material, sulfur-immersed material and the product pyrolyzed at 100 - 200 ºC are almost same, and with increasing the heating temperature to 400 ºC, that of the product increases, and above 500 ºC that of the product decreases. In immerse step, with increasing K2S concentration, the carbon content of the product at 400 ºC gradually decreases, the sulfur content of the product increases, and the recovery for nickel using the product gradually increases and then above 1 M K2S decrease. The product prepared from material immersed in 1 M K2S solution at 400 ºC indicates a maximum recovery for nickel ion. The product can adsorb nickel ion in nickel plating waste solution coexisting with phosphate ion, and adsorbed nickel ion in the product was deposited as nickel metal after heating at 1000 ºC under N2 atmosphere.INTRODUCTIONRice is the second world’s largest cereal crop after wheat, but produces large amount of straw residues, of about 330 million metric tonnes. Rice is a widely grown crop in Asia, and rice straw is produced as a by-product of rice production. In most parts of rice fields, open-field burning of rice straw is commonly practiced in the region when there is limited time to prepare a field for the next crop. However, open-field burning of crop residues is an uncontrolled combustion process during which air pollutants are emitted into atmosphere. These air pollutants have significant toxicological properties and are potential carcinogens (Gadede et al., 2009). Although wildfires are prohibited in cultivation fields of most countries, farmers usually keep on burning their crop by-products. Biomass burning is an important source of aerosol particles which may affect local and regional air quality (Gao et al., 2011), and also contribute to global climate changes."

Jan 1, 2016

By R. L. Marek

The number of persons fatally injured in the California petroleum industry in 1932 was 24, a decrease of 6, or 20 percent from the number killed in 1931. The decrease in the number of fatalities occurring in 1932 caused the fatality curve of the California petroleum industry to reach its lowest point in 10 years. Changing conditions in the oil industry - reduced personnel, decreased active field development, and curtailed production - have undoubtedly caused a part of this decrease, but continued accident-prevention efforts by the industry have also contributed to the reduction in the number of fatalities for 1932. The Bureau of Mines has analyzed and reported annually the fatalities in the California petroleum industry for a period of 10 years. Figure 1 shows the trend of fatal accidents during that period. Fatality statistics for 1932 show that the drilling and producing, pipe line and transportation, and refining and natural gasoline divisions of the industry had fewer accidents in 1932 than in 1931, sales and marketing being the only division that showed an increase over 1931. The number of fatalities by divisions for 1931 and 1932, percent of total, and percentages of increase and decrease are given in Table 1.

Jan 1, 1933