Search Documents

By Leong, William. Chong, Kam Weng

Deep Vibro Techniques namely Vibro Compaction (VC) and Vibro Replacement (VR) are widely used in ground improvement to densify sands and strengthen cohesive soils. This paper describes the application of these techniques for the construction of 20 Ha Iron Ore Stockpile Yard with the maximum stockpile height of 14 m in Quang Ngai, Vietnam. The challenges of this project are to limit the stockpile allowable settlement and the surrounding pile’s lateral movement. The soil condition can be summarized as 12m – 18m thick of loose to medium dense SAND with qc around 5-18MPa and followed by 2.0 – 6.0 m thick soft clay with qc around 0.4 – 0.8MPa. Localized very dense sand layer was found. VR using stone columns were installed in soft clay layer while VC was adopted to densify sand layer. Additional shallow stone columns were built in sand strata to minimize pile top lateral movement. The post construction performance was verified by a large 6 m by 12 m plate load test (PLT). The predicted PLT deformation using Priebe’s improved properties for the VR will be presented and compared with the measured plate load test results.

Nov 1, 2022

By Patrick J. Hannigan

The pile foundation designer typically performs a subsurface exploration program and static pile capacity calculations before selecting a pile foundation type, length, and capacity. During construction, a pile installation criterion must be established to meet these design requirements. This installation criterion usually consists of a minimum penetration resistance or blow count to confirm pile capacity and may also include a minimum embedment requirement. This text will focus on use of wave equation analysis and dynamic measurements to meet design requirements. BEFORE THE WAVE EQUATION Since the mid-1800s, over 450 dynamic formulas for pile driving control have proliferated. In their simplest form, these formulas relate hammer energy to the work of soil resistance, or simply: W ? h = R ? s (1) Where W = ram weight h = ram drop height or stroke R = pile capacity s = pile penetration per blow

Jan 1, 1990

By N. H. Snyder

THE Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the com-position as shown by proximate analyses. To these, when required, are added the fusing temperature of ash, Hardgrove grindability index, and the free-swelling index. Under most of these specification contracts the bidders guarantee the quality of coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions 4 issued by the Bureau; the samples are analyzed in the Bureau's laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of delivered coal and "tipple" samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) are valuable data for use in evaluating future bids. Moreover, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1953

The Arizona Committee, consisting of GERALD F. G. SHERMAN, Chairman, ARTHUR NOTMAN, Secretary, NORMAN CARMICHAEL, B. BRITTON GOTTSBERGER, W. L. CLARK, J. C. GREENWAY, W. G. MCBRIDE, FOREST RUTHERFORD, has arranged the following program for the Arizona Meeting, which has been approved by the President of the 'Institute and by the Executive Committee. It is printed herewith for the information of members, and probably will not be changed in any material respect. Monday, September 18, 1916.-Arrive at El Paso, Texas,, 6.30 A.M. Arrive at Deming, N. Mex., 9.30 A.M. Arrive at Chino, Ariz., 11.30 A.M., where luncheon will be served, after which there will be a visit to the Chino mines. From there the train will proceed to Hurley, N. Mex., where a visit will be made to the mill of the Chino Copper Co. Tuesday, September 19, 1916.-Arrive at Douglas, Ariz., at 8.00 A.M. The morning will be spent at the reduction works of the Copper Queen Consolidated Mining Co. "and of the Calumet & Arizona Mining Co. After luncheon a technical session will be held, with "Smelting" as a special subject for discussion. There will be a banquet in the evening, followed by another technical session or-a business meeting.

Jan 6, 1916

By P. J. Burkhardt, L. V. Gregor

The oxidation kinetics of single-crystal silicon has been investigated using extremely dry oxygen as the oxidant. Two techniques were used. The first involved a flow system with which incremental thickness measurements were made. This sytem provided an oxygen ambient at atmospheric pressure which had a moisture content of less than 0.1 ppm of water. The second technique involved measuring the change in volume of oxygen with time in a closed system. A temperature range of 900O to 1200 "C and a pressure range of 20 to 760 Tory were covered. Both techniques showed that a simple parabolic rate law holds only at the higher temperatures. At lower temperatures, the data up to 5000Å can be fitted well to a linear-parabolic equation. The two constants in this rate equation are examined in terms of a physical model. The parabolic portion of the low-temperature oxidatLon fits along the high-temperature curve of an Arrhenius plot. The parabolic rate constant for the flow-system technique can be expressed by k = 2 x 10-9 exp (L 31 kcalRT) sq cm per sec. The manostatic technique gave k = 1 x 10-exp (- 23 kcalRT) sq cm per sec. By extending the thickness range to over 104. a rate law of X = At seems to fit all of the data better than the linear-Pavabolic law. Here the exponent n increases from 0.518 at 1150 V to 0.637 at 900°C. PASSIVATION of silicon planar devices through thermal oxidation is of such great importance that considerable effort has been devoted to the study of the process.17 Much of this work involves hydrothermal oxidation, in which H2O is the oxidant: whereby H2 is produced. It has been proposed that the reaction proceeds by the formation of Si-OH groups and hydroxyl diffusion through the film to react with the silicon surface. Thus, the silicon oxide layer probably contains residual hydrogen in some form after oxidation in H2O and it has already been established that hydrogen has a marked effect on the electronic properties of oxide-passivated silicon surfaces. Silicon is oxidized by oxygen at elevated temperatures; but the rate of oxide formation is considerably lower than that for 0." By using dry O2 as the sole oxidant, the presence of residual hydrogen is presumably avoided. At present, the mechanism of thermal oxidation by dry O2 is a matter for conjecture, and the presence of small amounts of H2O was reported to have a marked effect on the rate of oxide formation10 (perhaps on the electronic properties of the surface, as well). Hence, this study of the kinetics of silicon oxide growth in 0, was undertaken: 1) to determine the oxidation rate at atmospheric pressure in a system designed to exclude rigorously all traces of H2O in the ambient 0,; 2) to obtain oxidation-rate data in situ in dry O2 by means of a continuous monitoring of the amount of 0, consumed during oxide growth. These objectives are complementary—the first assesses what effects (if any) are obtained by excluding H2O from the reaction, and the second expands this information while at the same time avoiding the uncertainty inherent in relying upon incremental measurements of oxide growth to furnish kinetic data. EXPERIMENTAL PROCEDURE The conventional silica open tube in a resistance-heated oxidation furnace is subject to sources of trace H2O, even after the input O2 is thoroughly dried and the outlet gas stream is passed through a trap to prevent

Jan 1, 1967

By B. Abedian, L. M. Racz, S. R. Berry, R. W. Hyers

"The presented work represents an effort to improve understanding and prediction of turbulent flow inside electromagnetically-levitated droplets. We show that the flow field in a test case, a nickel droplet levitated under microgravity conditions, is a low Reynolds number turbulent flow, i.e. in the transitional regime between laminar and turbulent. Past research efforts have used laminar, enhanced viscosity, and k - E turbulence models to describe these flows. In our study, we compare the RNG algorithm to laminar and k - E turbulence model results. We show that accurate description of the turbulent eddy viscosity µr is critical in order to obtain realistic velocity fields, and that µr cannot be uniform in levitated droplets. In the RNG method there are no characteristic length or time scales associated with the flow, thus allowing such anisotropic features to be captured. We perform calculations and analyses for two cases (1) a small, non-deforming, spherical nickel droplet and (2) a deforming, oscillating droplet. In addition to flow field calculations, we compare numerically-obtained surface tension and viscosity values to those obtained experimentally by the oscillating drop technique.IntroductionElectromagnetic levitation (EML) is a containerless processing technique for conductive materials. Its advantages are the avoidance of contamination or chemical reaction at container walls and the ability to perform long-term experiments in a metastable state. Because of its current limitation to small sample sizes, its primary use is in the laboratory. One application of interest is the measurement of thermophysical properties of undercooled liquid metals [1, 2, 3, 4]. In EML, a sample weighing approximately 1 gram is positioned inside an electromagnetic field generated by alternating currents flowing through an axisymmetric water-cooled copper coil. The coil must be designed appropriately so that thesample levitates in a stable manner.Traditionally, mathematical modeling has been performed in tandem with both earth-and spacebound electromagnetic levitation experiments, in order to determine the effect of the magnetic field on material and flow characteristics [5, 6, 7, 8]. These calculations are important because they allow design, planning, and correct interpretation of experiments. In addition, the calculations are of fundamental scientific interest, as they can be applied to other electromagnetic materials processing applications [9]."

Jan 1, 1999

By Wayne L. Worrell

Thermodynamic data for the stable carbides and oxides of chromium, molybdenum, and tungsten have been critically eualuuted and are used to determine the stable condensed phases at 1 atm total pressure in each metal-carbon-oxygen system. Pourbaix-Ellingham diagrams have been constructed and are used to estimate the minimum temperatures neces.see)*y to oblain these metals by corbolhermic redlrction under reduced pressures. USING recently reported data for the carbides and oxides of chromium, molybdenum, and tungsten, the stable phases in the Group VI metal-carbon-oxygen systems at specific temperatures and pressures can be determined. The thermodynamically stable regions in each metal-carbon-oxygen system can be completely pictured using a Pourbaix-Ellingham diagram in which the two coordinates are oxygen potential (-RT In Po2) and temperature. Worrell and chipman' have described and constructed such diagrams for the metal-carbon-oxygen systems of vanadium, columbium, and tantalum. Downing2 has used similar diagrams to provide a description of the reactions in submerged arc furnaces. One of the examples which he cited was the Cr-C-O system; however, an improved diagram is presented in this paper using recently obtained data for the carbides of chromium. Although some of the oxides and carbides of the Group VI metals exist over slight ranges of composition,3 all solid phases are represented as stoi-chiometric compounds in the subsequent diagrams. Any error introduced into the calculated equilibria by neglecting the compositional variation of these phases is less than the uncertainty in the thermodynamic data. In a Pourbaix-Ellingham diagram for a three-component system, the phase rule requires that at equilibrium four condensed phases specify a point, three condensed phases determine a line, and two condensed phases define an area. To obtain a well-defined area at high oxygen potentials and teniperatures, the initial carbon to oxygen mole ratio is specified to be more than sufficient to reduce the oxide but not enough to convert all the metal to carbide. Thus, the lowest regions in the subse- quent Pourbaix-Ellingham diagrams represent areas in which the metal and its carbide are the stable condensed phases. Cr-C-O SYSTEM A) Thermodynamic Data. To simplify the subsequent calculations, all thermodynamic data are presented in the form of linear Gibbs-energy-of-formation* equations which were derived for the temperature range 505° to 2000°K and are reasonably accurate over the entire temperature ranges of the diagrams. The thermodynamic data for the compounds occurring in the Cr-C-O system are summarized in Table I. Several volatile chromium oxides have been reported,4 but their influence is negligible in the Cr-C-O system. Thermodynamic data for CO and CO2 were taken from the compilation of Coughlin.5 The only solid chromium oxide sufficiently stable to exist below 1800°K in the Cr-C-O system is Cr2Os.11 The Gibbs-energy-of-formation equation for Cr2O3 was obtained by revising the data tabulated in Coughlin,5 using the heat of formation of ah' and the high-temperature thermal data for chromium.7 In 1953 Richardson8 re-evaluated the original work of Kelley and coworkers,9 who measured the thermodynamic properties of the chromium carbides. However, the high-temperature equilibrium results of Boericke9 yield values for ?G°f of Cr2O3 which are 2 kcal more positive than the accepted data. His results for the chromium carbides are based on the same questionable equilibria. Gleiser10 recently determined the Gibbs energy of formation of Cr3C2 and the equation in Table I was calculated from her data and the thermal data of Kelley and coworkers.9 Thermodynamic data for the Cr7C3 and Cr23C6 carbides were obtained by combining the Cr3C2 data

Jan 1, 1965

[NOTE.-The names of authors of papers are printed in small capitals, and the titles of papers, in italics. Casual notices, giving but little information, are indicated by bracketed page numbers. Large Roman numerals are volume numbers; small Roman numerals after volume numbers following titles indicate the page on which the presentation of the paper is mentioned; Arabic figures refer to the text of the printed papers.] A Use Classification of Coal, (ASHLEY) LXII [xiv]; LXIII, 782; Discussion: (HALL), 794; (ZERN) , 795; (ASHLEY), 795 Absorbent material, liquid-oxygen explosives, LXXI, 1251. Absorbents for liquid-oxygen explosives, LXIX, 292, 299. Absorption : cupellation : gold, special cupels, LIX, 194. primary and secondary, LIX, 213. ratio of silver to gold, LIX, 212. silver, specla1 cupels, LIX, 195. Absorption method, gasoline from natural gas, LIX, 584, 585. Absorptzon of Sulfur from Producer Gas zn Open-hearth Furnaces (NEAD), LXX, 176; Discussion: ( WATERHOUSE), 184 ; (REYNDERS) , 184; (KINNEY), 184 Accelerated wearing tests, bearing metals, LXIX, 973. Accident prevention, results, Utah, LXVIII, 360 Accident Prevention, 1919 (SINN), LXIII, [xiii] Accidents: causes in coal mines, LXXI, 1229. classification, Anaconda Copper Mining Co., LXVIII, 9. coal mining: comparison with metal mining, LXVIII, 360. pillar mining, LXVIII, 323. relation to method, LXVIII, 323 shafts, LXVIII, 207, 209 Utah, LXVIII, 363 - concentrating mills, Utah, LXVIII, 362 liquid-oxygen explosives, LXIX, 330, 339 losses through, LVIII, 65 metal mining, LXVIII, 361, 363. mine: causes, LIX, 652. curve of decrease, LIX, 655 days of greatest frequency, LIX, 657 human element as cause, LIX, 652, 653. intemperance as cause, LIX, 658 labor relation, LIX, 652 prevention, LIX, 653. record, New Jersey Zinc Co., Franklin mine, LIX, 655 time of greatest frequency, LIX, 657, 658 Utah, LXVIII, 360 prevention, LVIII, 65 report blanks, Anaconda Copper Mining Co, LXVIII, 13, 15. statistical base, Anaconda Copper Mining Co, LXVIII, 9 time lost, LVIII, 70 transportation, Clifton-Morenci district, LXX, 851.

Jan 1, 1926

By Masami Taguchi

"It is found that lead monoxide, PbO, has an ionic conductivity, and the all solid-state electrochemical cell using this oxide as an electrolyte has attracted the attention of battery researchers. In this study, thin film PbO2/PbO/Pb solid cells were produced on glass substrates and their discharge properties were investigated. The acti.ve material for the positive electrode, PbO2, was obtained by reactive sputtering of a Pb target in oxygen plasma. The PbO electrolyte and the active material for the negative electrode, Pb, were vacuum evaporated from /3 -PbO powder and a Pb block, respectively. The open-circuit voltage of the cell agreed with the theoretical value based on the thermodynamic data, and the close-circuit voltage was improved by the addition of a univalent impurity such as sodium or potassium to the PbO electrolyte. The connection of the cells in series and in parallel produced a higher electromotive force and a larger capacity. Also, the charge-discharge cycling test revealed that the cell could be charged and function as a storage battery.IntroductionGenerally, the ionic conductivity of a solid-state electrolyte is lower than that of a liquid electrolyte near room temperature. This has been a serious obstacle to using such electrolytes in an electrochemical cell. However, some solid-state electrolytes, which can preferentially pass a specified ion and have high ionic conductivity, have been found. Lead monoxide, PbO, which is an oxygen ion conductor, is such an example (1)(2). If a solid-state electrolyte is adopted for use in an electrochemical cell the problem associated with a liquid electrolyte such as leakage can be alleviated. The cell structure also can be simplified, because the electrolyte plays the role of separator to prevent the active materials from mixing. Thus, physical vapor deposition technology may make it possible to develop a very thin film cell, which consists of only solid phases (3)(4). In this study, the thin film PbO2/PbO/Pb solid cell with a thickness· of only a few micrometers, in which all the constituents were systematically deposited on a glass substrate by reactive sputtering and vacuum evaporation, has been produced and the charge-discharge properties were investigated. An attempt was made to improve the discharge properties by doping impurities such as Na2CO3 and Sb2O3 into the PbO electrolyte. Moreover, the connection of the cells in series and in parallel to get a higher electromotive force and a larger capacity, and the charge-discharge cycling test to determine its use as a storage battery were carried out."

Jan 1, 2000

Can mining promote sustainable development? What is sustainable development? Is sustainable development good for corporate sustainability? Does it work in practice? If so, is it good for business? This paper does not seek to provide definitive answers to these issues. Rather, it is presented in the interests of sharing information and contributing to the pool of collective experience. The discussion will draw on the experience of Placer Dome in Papua New Guinea (PNG). Sustainable development means development that is maintained at a steady level without exhausting natural resources or causing ecological disturbance. The term æsustainable developmentÆ is often linked to the concept of ecological equilibrium, development that is self-replenishing. While its essential meaning remains the same, in practice, and for todayÆs complex and industrial world, different people will interpret sustainable development in different ways. Given the dynamics of development and the competing social, political and economic interests, sustainable development must be seen from a much broader perspective. This is the point that this paper will attempt to make. Mining, an activity that uses non-renewable resources, can promote sustainable development. The 1987 Brundtland Report (also known as the Report of the World Commission on Environment and Development), defines sustainable development in a broader manner - as development that meets the needs of the present world without compromising the ability of future generations to meet their own needs (Elkington, 1997). This definition calls for inter-generational equity in the development and use of resources by many organisations, including multinational corporations. Corporate sustainability, on the other hand, is about developing strategies that guide a corporation to stay alive and, more importantly, to stay ahead of its competitors. It is basically about survival in a competitive social and commercial environment. In a corporate world, profitability is survival. In this context, corporate profitability, the main ingredient of corporate sustainability, is important for sustainable development. Without profits, corporations will find it difficult to practice sustainable development or indeed any development. Sustainable development can integrate mining activities with the rest of the community, add value and, in the long-term, profits to the bottom-line. Ultimately, sustainability will force corporations to adopt strategies based on a longer time scale to survive. In the mining sector, corporate sustainability depends on a close relationship with all stakeholders, particularly landowners for whom sustainable development is critically important. Increasingly, there is an acceptance of the view that success is not achieved simply through competition in price, cost and technology but, more importantly, through creating social infrastructure which support community ethics, norms and values essential for trust and partnership. Needless to say, mining companies that engage in appropriate community-based development in support of inter-generational justice recognise the true value of sustainability. This is sometimes called the æhuman sustainability approachÆ which underlines the critical significance of trust in relationships with stakeholders and continuous improvement of corporate capabilities directed towards the future (Dunphy and Griffiths, 1998). In the long-term, such development will enhance corporate public image and acceptability. In practice, both concepts can be built on the principles of economic viability, environmental quality and social justice -what, in todayÆs parlance, is increasingly becoming known as the ætriple-bottom-lineÆ approach to business (Elkington, 1997). Underpinning this approach is a process of continuing dialogue and co-operation between governments, non-government organisations (NGOs) and business.

Jan 1, 1999

By John Pekrul

Coeur Rochester Inc. located in north central Nevada, operates an open pit mine moving a total of 16 - 18 million short tons of material per year. A three stage crusher produces approximately 8 million tons of a minus half inch product that utilizes truck stacking to construct a heap leach with a zinc precipitation recov­ery plant. Coeur Rochester recovers approximately 6.0 - 7.0 MM ounces of silver and 60 - 80 K ounces of gold annually. Current metal prices and good operating practices require contin­ued review of operating systems that support the operation, thus the development of a Strategic Mine Plan. This Strategic Mine Plan provides managers, engineers and supervisors a means to improve their operations through three main objectives: 1. Reduce operating costs, 2 .. Increase production, 3. Increase mine life (reserves). These three main objectives will be reviewed in context to their current status and past performance.

Jan 1, 1999

By James A. McGrath

"The predominant key word associated with all commercial blasting methods is “safety”. Safetyshould take precedent over all other aspects of the entire explosives industry which on a wholehas had an excellent track record as to number of injuries per unit of hours worked at all blastsites throughout our country."

Jan 1, 1999

By M. Wenzel, Dang Thanh Tung, Nguyen Anh Duc, Nguyen Huu Luong, Dang Van Sy, N. Kelly, K. Gloe, K. Kretschmer, Phuc Nguyen Le, K. Schnaars, S. Robles M, L. Götzke, J. J. Weigand

The recovery of rare earth metals from secondary sources has attracted much attention due to their ever expanding demand in the high-tech industry. The studies reported here focus on the hydrometallurgical recovery of lanthanum and cerium from spent fluid catalytic cracking (FCC) catalysts in a two-step process: leaching with nitric acid and solvent extraction by tri-n-butyl phosphate (TBP) and di(2-ethylhexyl)phosphoric acid (D2EHPA). The experiments show a high dissolution yield of about 93% lanthanum and 42% cerium in a single leaching step with 2 M (126 g/L) HNO3 at 80 °C; only 11% aluminum has been dissolved simultaneously. In the subsequent solvent extraction step the best results for this leach liquor could be achieved using a 1:1 mixture of 25% (v/v) TBP (0.92 M) and 25% (v/v) D2EHPA (0.76 M) in n-decane without the need for any pH adjustment. In that case La(III) and Ce(III) can be extracted with 60% and 74% yield respectively in one stage from the majority of accompanying matrix elements. In particular no extraction of Al(III) could be observed under these conditions.

Jan 1, 2016

The modern resource extraction enterprise is a complex capital intensive business operating in a world of constantly evolving social, environmental and economic scrutiny. Investors, government, media and special interest groups expect to see business environmental and social performance respond and deliver increasing corporate responsibility and sustainability.   Thorough interrogation of business performance using a multi-disciplinary due diligence approach presents a more sophisticated review and benefits beyond the traditional compliance/conformance 'audit' style assessment.   Using a due diligence approach allows assessment through a comprehensive lens which examines potential short- and long-term risks including sometimes less tangible environmental and social liabilities, and informs management, investors and regulators of broader business performance. This approach provides information in a form that business can measure performance in a repeatable and enterprise wide sense.   This paper provides an outline of the due diligence process applied in this way, drawing from lessons learnt and industry based experiences in the due diligence process and the benefits and tools that can  be applied in an environmental and social due diligence business performance assessment

Jun 1, 2010

By Charles L. Kimbell

In overview, 1988 appeared to be the best year for the world's mineral industry since 1980, although the all-important petroleum component suffered severely from low prices. With this notable exception, the traditional statistical measures of mineral industry performance, namely production, trade, and consumption, reflected growth in most elements of the world mineral industry from crude material extraction through the gamut of downstream processing. Moreover, the growth was reasonably well distributed geographically, with many countries sharing in the substantial upturn in activity. World crude mineral output value was estimated at over $1,272 billion in current dollars ($1,090 billion in constant 1983 dollars). The value added by the processing component of the mineral industry raised the total value of the industry's output to an estimated $3,057 billion in current dollars ($2,620 billion in constant 1983 dollars). Less easily assessed was the value of mineral commodities moving in 1988's international world trade, particularly because of the declines in world crude oil and refinery product prices. It remained to be seen if increased volume and value in nonfuel mineral and coal exports, coupled with an increase in the volume of oil exports, would be adequate to offset the drop in oil prices. Whether or not the value of world mineral commodity trade topped the 1987 level of over $498 billion, an increase in the volume of mineral commodity trade was almost assured. Similarly, although comprehensive statistics were not avail-able on consumption of all mineral commodities in all countries, available data on selected major commodities in selected major countries suggested that not only had output of most mineral commodities advanced, but so too had consumption levels for most commodities.

Jan 1, 1990

By Theodore H. Budd, Austin M. Cooney

The North Shore 9 Collector System comprised an integral part of the Milwaukee Metropolitan Sewer District's Water Pollution Abatement Program. The project required the construction of 1,490 m of tunnel, ranging from 1.5 m to 4.6 m in diameter along three separate alignments beneath arterial streets traversing Milwaukee's central business and cultural districts. This paper details the various aspects of the tunnel drives which were accomplished using two Lovat EPB type TBMs in conjunction with pipe-jacking procedures. Shaft configurations developed for the project, including ancillary subsidence mitigation components and portal pressurization facilities are discussed. Anomalies in observed soil behavior at variance with the parameters delineated in the project's geotechnical report are addressed.

Jan 1, 1991

By Theodore H. Budd, Austin M. Cooney

The North Shore 9 Collector System comprised an integral part of the Milwaukee Metropolitan Sewer District's Water Pollution Abatement Program. The project required the construction of 1,490 m of tunnel, ranging from 1.5 m to 4.6 m in diameter along three separate alignments beneath arterial streets traversing Milwaukee's central business and cultural districts. This paper details the various aspects of the tunnel drives which were accomplished using two Lovat EPB type TBMs in conjunction with pipe-jacking procedures. Shaft configurations developed for the project, including ancillary subsidence mitigation components and portal pressurization facilities are discussed. Anomalies in observed soil behavior at variance with the parameters delineated in the project's geotechnical report are addressed.

Jan 1, 1993

By S. S. Peng

This paper presents a convenient way for the preliminary design of the shield supports. The locus equations which are applicable for all kids of shield supports are derived. These equations facilitate the statics analysis of the shields. An indirect method in determining the coefficient of friction, the external toads and their locations are also developed.

Jan 1, 1982

By Thomas Gales

Longwall mining has a high potential for producing bulk production from a single face. Production is interrupted for a considerable time when it is necessary to move the equipment to a new block of coal. The frequency of such moves can be reduced by increasing the dimension of the block to be moved. Merely doubling the tonnage in a block to be mined may increase production by more than 21,000 tons per year. The time taken to move the equipment can be reduced by careful preplanning, industrial engineering analysis, and specially designed equipment. Reducing its move time from 30 days to five days can increase production by more than 25,000 tons per year. Increasing the panel dimensions and reducing the move time can give an increase in pretax profits of more than $600,000. A comprehensive bibliography is included.

Jan 1, 1977

By C. W. Owings

Recent recommendations of the Bureau of Mines regarding, rock dusting to prevent dust explosions in coal mines have been issued as Mine Safety Board Decision 32 and printed as Information Circular 7109.5/ The last paragraph on page 2 of I. C. 7109 states: After a mine or any part of a mine has been rock-dusted, samples of dust for analysis should be taken from the floor, ribs, roof, and timbers at such intervals of time as will give apple warning of need far redusting in order to maintain the required minimum percentage of incombustible in the mine dust. Details of the methods of sampling and analysis are given in Bureau of Mines Information Circular 7113.

Jan 1, 1940