Search Documents

By W. L. Fink, L. A. Willey

During the war there was introduced a new higher strength aircraft alloy designated 75S.1,2,3 The properties of this alloy assure extensive applications in both military and commercial aircraft. It is therefore important to understand its limitations as well as advantages. The properties of 75.5 alloy in the heat-treated tempers, like those of many other aluminum alloys, are affected by the rate of quenching. In general, low quenching rates tend to cause low strengths and to adversely affect the resistance to corrosion. Commercial quenching procedures are usually sufficiently rapid to permit the development of maximum properties. However, in the center of heavy sections, such as large rolled and extruded shapes, the quenching rates may not be rapid enough to develop maximum strength or resistance to corrosion. The investigations of 75s alloy described herein reveal the most critical range of temperature and the effects of quenching sheet and extrusions at different rates through that temperature range, on the tensile properties and resistance to corrosion. Procedure Preparation of Specimens Sheet specimens (3 in. by 9 in.) were prepared from a commercial lot of 75s "as rolled" sheet (0.064 in. thick). The composition4 was as follows: Weight Percentage Cu Mn Mg Zn Cr A1 with Normal Impurities 1.64 0.16 2.58 5.66 0.27 Remainder The specimens employed for the determination of the time-temperature relations during quenching of sheet were prepared by the following procedure: the hot junction of a 28-ga. iron-constantan thermoelement (asbestos insulated) was brazed to a thin strip of aluminum which was in turn brazed into the end of a 3/16-in. id by %-in. od by 30 in. long aluminum protection tube. Before brazing, the tube was flattened to 0.064-in. thickness over the junction and adjacent lead wires for a distance of I 1/2 in. The flattened end of the tube was fitted into a slot cut from one edge to the center of the 3-in. by 9-in. by 0.064-in. sheet and brazed into place. The brazed joint was dressed to the thickness of the sheet and the entire specimen buffed to approximately the brightness of "as rolled" material. Because of the brazing operations required, these specimens were prepared using 3S alloy. For the investigation of quenching rates in heavy sections, there were used 75s extrusions which had compositions similar to that of the sheet. The specimens consisted of 14 in. lengths of 3i-in., 2-in., 3-in, and 4-in. diam cylindrical rods and a roughly rectangular extruded section which was approximately 4 in. by 7 1/2 in. Thcrmocouple~ were peened into the bottoms Of .1/8-in. diam wells drilled into one end and parallel to the axis to a depth of

Jan 1, 1949

By C. D. Mishra

The recycling potential for any gainful utilisation of the waste products is dictated by their quality, especially the chemical characterisation. The methods commonly used for the analysis of fly ash e.g. wet chemical, AAS, ICP-AES etc are time consuming. The paper describes a rapid XRF-based method for routine analysis of fly ash which involves preparation of local standards, optimisation of sample preparation technique and use of a simple PC-based software to account for interelement effects. The matrix corrected values are found to agree well with the wet chemical data.

Jan 1, 1992

By Henry Rumfelt

8.1-1. History and Description of Shovels. The history of excavating machinery is not clearly defined but the machines seem to have been originally developed for dredging activities, principally involving rivers and harbors. The first, as far as can be determined, was a steam "spoon dredge" developed by Grimshaw of Boulton and Watt of Sunderland, England, in 1796. The land machine forerunner of the present-day power shovel was not developed until 1835. It was invented by William Smith Otis, a young partner of a Philadelphia contracting firm by the name of Carmichael and Fairbanks. The moving force behind this invention was the heavy activity in railroad construction. From this early start the power shovel has developed from steam powering to internal-combution-engine powering and to electric powering. In both directions it has developed to its present state of a finely engineered and precision-built tool. Through the interim the railroad-type shovel, about a half-swing arrangement designed especially for making railroad cuts and mounted on rails, was developed. The rail-mounted shovel gradually gave way to the full revolving shovel. It was high on the list in 1912 and was practically extinct by 1927. From the beginning, a few of the small revolving shovels designed primarily for the general contractors' market had found their way into quarry and mining operations. During this same period, the stripping shovel had been introduced-a 2 ½ cu. yd., 100-ton, full revolving stripping machine with a 41 ft boom. Although this shovel was designed especially for stripping, it was also used for heavy-duty, open pit mining service. In 1925 the heavy-duty, full revolving quarry and mine machine was developed. Strip mining shovels evolved through a somewhat separate path. Hand digging plows and mule-drawn slip scrapers were first reported used by Kirkland, Blakeney and Groves near Danville, Illinois for strip mining

Jan 1, 1968

By Barbara Fotta, Lynn Rethi

Within the Mine Safety and Health Administration's (MSHA's) classification of metallnonmetal (MAM) mining, the number of independent contractor' employees has increased significantly in recent years. In 1985 independent contractor employee hours reported to MSHA accounted for 4.5% of all M/NM mining employee hours (excluding office workers); by 1994 that proportion had doubled to 9.0%. As a result, these workers now account for an increasingly significant proportion of fatal and nonfatal mining accidents. According to MSHA's statistics, annually computed fatality incidence rates (the number of fatalities per 200,000 employee hours) for independent contractors working in M/NM mining are consistently higher than those for operator employees. Over the five-year period from 1990 through 1994, 53 independent contractor employees were fatally injured while working on M/NM mine property (See Table 1). More than one third of these fatalities (36%) were due to accidents involving powered haulage; 21% were machinery accidents; and 11% percent were falling material accidents. Combined, these three accident classifications accounted for 68% of all independent contractor fatalities occurring on M/NM mine property during these years. Clearly, current efforts to increase the safety of the mining workforce must also address the safety of the independent contractor employee. This report is a preliminary attempt to identify trends in the employment and safety of independent contractor workers by identifying which segments of M/NM mining are experiencing the greatest increases in the number of independent contractor employees and by examining changes in the rates and types of accidents in which these employees are involved. The employment and accident data used in this report were obtained from the MSHA database. [ ]

By Sukumar Bandopadhyay

In recent years, research in the field of artificial intelligence (AI) has had many important successes. Among the most significant of these has been the development of powerful new computer software known as the "expert systems". Expert system programs designed to provide expert-level consultative advice in mineral exploration (Duda et al, 1981), scientific (Feigenbaum, Buchanan and Lederburg, 1971) and medical (Shortliffe, 1976) problem solving are generally acknowledged to be among the forerunners of this research. As the decision makers virtually in all fields face a more complex and involved world within which to operate, the need for some decision support is also becoming urgent. Thus applications of expert systems continue to spread out reaching problems that, because of their dimensions or particular aspects, set more demand on the decision methodologies. To meet these new requirements, many activities which were performed in the past by the domain expert or engineer must become automated. Furthermore, previous research (Dawes and Corrigan, 1974; Dawes, 1979) has shown that automating an expert's decision rules often provide better decision than the expert does. For large systems it would be very useful (or even necessary) to have formal tools, allowing one for example, to automatically discover inconsistencies, contradictions or redundancies, or to identify the possibilities of wrong lines of reasoning in the decision process.

Jan 1, 1990

By N. J. Grant, K. M. Zwilsky, J. T. Blucher

DISPERSION strengthening has been studied in a number of metal-metal oxide systems. To date those pure metals available as fine particles (less than about 5 p) have received most of the attention whereas solid solution alloys, generally unavailable as fine powders, have not been examined in detail. The present work was undertaken as a preliminary study to evaluate combined effects of solid solution and dispersion strengthening. The technique used was that of dry mixing of elemental powders with the oxide, followed by a diffusion treatment to obtain the solid solution. The average particle size of the powders used was: Ni, 3.2 p (1nco B); Mo, 1.3 p (Fansteel Metallurgical Corp.); and y alumina, 0.027 \i (G. L. Cabot, Inc.). The particle size of the metal powders was determined by Fisher subsieve measurements while the size of the alumina was calculated from a surface area determination. Prior diffusion studies on small compacts pressed from mixtures of nickel and molybdenum powders with and without 7.5 vol pct A1203 indicated that diffusion was complete after sintering for 100 hr at 1800" , or 50 hr at 2250", or 20 hr at 2550° F. The progress of diffusion was followed by microstructural examination and micro-hardness measurements. Two observations made during the diffusion experiments were: 1) That diffusion proceeded faster in the presence of alumina, confirming similar findings by Seith and Loepman on "SAP'';4 2) That diffusion at temperatures above 1800°F resulted in coarsening of the alumina in agreement with results of other authors reporting on the growth of alumina in nickel above 1800"F. Similar experiments in the Ni-Cr system using 6 and 20 p Cr powders of 0.7 and 0.025 pct 0, respectively, did not result in significant solid solution formation even after long time exposures at 2550° F. It must be concluded that chromium oxide films around individual particles interfere with normal diffusion. A nickel alloy containing 5 wt pct Mo and 7.5 vol pct alumina was fabricated by dry mixing of powders, isostatically compacting at 30,000 psi, diffusing for 120 hr in dry hydrogen at 1800" F, and extruding at 1950"~ with a 30 to 1 reduction of area ratio. The resulting structure, presented in Fig. 1

Jan 1, 1963

By Jr. Flynn

This U.S. Bureau of Mines publication is a compilation of fundamental cyanide chemistry data obtained through review of the scientific literature. It includes information on thermodynamics and chemical equilibria, ultraviolet-visible and infrared spectra, and the chemistry and photochemistry of cyanide, chemical species derived from cyanide, and metal cyanide species. It also includes guidance on the use of the data for solving practical problems in precious metals applications. This publication is intended mainly for use as a reference by personnel in the precious metals industry and regulatory agencies, and other cyanide users, to provide comprehensive information on cyanide chemistry. The document should assist in the formulation of effective policies for cyanide control in the construction, operation, and closure phases of precious metals mining and metallurgical operations. In addition, the data in this publication will be useful in other contexts, such as dealing with industrial cyanide usage, cyanide-containing wastes and associated environmental problems.

Jan 1, 1995

NIM Reports Report No. 1563 Neutron activation analysis of samples from the Kimberley Reef Conglomerate. Report No. 1569 The use of DDTU as an analytical reagent for the noble metals. Special general meeting A Special General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 14th November, 1973. The President, Mr P. W. J. van Rensburg, opened the meeting at 9 a.m. and read the notice of the meeting, which was as follows: Colloquium and general meeting CONSTRUCTION OF SLIMES DAMS A General Meeting and Colloiquum on the above topic was held on November 14th and 15th, 1973, at Kelvin House, Johannesburg. Mr P. W. J. van Rensburg (President) was in the chair. The Colloquium was attended by 135 delegates and was opened by the President at 9.10 a.m. Orange Free State Branch PROCEEDINGS OF THE ANNUAL GENERAL MEETING The Annual General Meeting of the Branch was held in the Western Holdings Cant,een on Tuesday, 11th September, 1973, at 7.00 p.m. Book Review Westwood, W., and Cooper, B. S. Analytical methods in use in non-ferrous minin~ and metallur~ y: a selective review. London, Institute of Mining and Metallurgy, July 1973. 54 pp. £3.50.

Jan 12, 1973

The Institute assembled in the rooms of the Geographical Society, Cooper Union, at 8 o'clock P.M., February Nth, 1874. President Barnard, of Columbia College, delivered an address of Welcome, to which President Raymond responded. The Council then presented the following names, duly indorsed for election as members and associates. The gentlemen named were unanimously elected. *Bullock, M. C.,. ., . New York. Burke, M. D.,.... Cincinnati, Ohio. *Burt, M. W.,.....Wheeling, W. Va. Cameron, J. G. M.,. ..'New York. *Canfield, Frederick A,,. .. Dover, N. J. *Chandler, Prof. C. F.,. .. New York. *Clayton, J. E.,. .. . Salt Lake City. Colton, C. A,,.... New York. *Cooke, Prof. George H.,. . New Brunswick, N. J. *Cooper, Edward,.... New York. "Dahlgren, C. B.,.... Mazatlan, Mexico. Dutton, Capt. U. E.,. .. Washington, D. C. *Eurich, E. F.,.... New York. Fuller, H. L.,.... Woodside, Luzerne County, Pa. Hamilton, S. Jr.,.....New York: Harnickell, A,,.,.. New York. *Hearne, F. J.,. .. . Wheeling, W. Va. *Hill, Samuel W.,.... Marshall, Mich. *Hulbert, Edward J.,. . Houghton, Mich. *Hunt, R. W.,.....Troy, N. Y. Ihlseng, M.,.....New York. "Iselin, Henri,.... New York. *Janney, Morris P.,. ..Pottstown, Pa. "Jenney, Frank B.,. .. . Brooklyn, N. Y. *Jenney, Walter P.,... Brooklyn, N. Y. Joy, D. A.,.....New York. *King, Clarence,.... New York. *Kittoe, E. F.,....Charleston, S. C. Lawrence, Robert,.... New York. *Locke, J. M.,..... Cincinnati, Ohio. *McCormick, Henry,. .. Harrisburg, Pa.

By F. Ajersch, M. Rigaud, M. Jallouli

"Le gonflement des boulettes d'hématite à été étudié à l'aide d'une méthode de mesure standard ISO ainsi qu'à l'aide d 'une méthode de mesure dilatométrique.La première méthode a servi à l'étude des boulettes haute silice (5% SiO2) dont l'indice de basicité (IB = CaO + MgO -i- SiO2 + Al2O3) a été ajustée soit à l'aide d'une addition de dolomie, soit à l'aide d'une addition de pierre à chaux, soit à l'aide d'une addition de ces deux composes. L'indice de basicité variait de 0.05 à 0.12. Les résultats de gonfle ment obtenus à 1000?C dans une atmosphère de 40 CO - 60 N2 ont permis de montrer qu’indépendamment de l'indice de basicité c'est la dolomie qui contribue le plus à diminuer le gonflement par rapport à la pierre à chaux. L'utilisation de l'indice de basicité comme critère de sélection des boulettes est discutée.La méthode dilatométrique a servi à l'étude du gonfle ment de deux types de boulettes préparées à partir de deux concentrés de fer et dont la teneur en silice a été fixée à 2.5% et 0 5%. Ces deux types de boulettes ont reçues les mêmes additions de liant en quantité et en nature. La détermination en continue du gonflement, à 950?C dans 40 CO - 60 N2, a permis d'une part de mieux cerner le niveau de réduction auquel correspond le maximum de gonflement et d'autre part de montrer que l’allure des courbes de gonflement est étroitement liée à la nature du liant. Une augmentation de la teneur en silice des concentres contribue à diminuer le gonflement des boulettes.Des essais de réduction de gonflement non isothermes ont été réalisés à des montées de température à 10 et 20?C/min. Les résultats indiquent que le gonflement déterminé dans les conditions non iso thermes est inferieur à celui obtenu lors des essais isothermes. On discute alors de la validité des essais standards de gonflement qui sont utilisés pour prédire le comportement des boulettes lors de leur réduction dans un haut fourneau."

Jan 1, 1983

By M. J. Ferrante

A process was investigated for preparing Specification-grade nickel (containing less than 1 percent cobalt) by stripping it electrolytically from a nickel sulfate-boric acid solution and using the stripped electrolyte for the preferential dissolution of nickel from basic carbonates of nickel and cobalt. The basic carbonates were produced at the plant at Nicaro, Cuba, owned by the U.S. Government. Determination of the optimum conditions for deposition of Specification-grade nickel indicated that the upper limit of cobalt concentration was 0.1 gram per liter. The pH, temperature, and concentrations of nickel and boric acid in the electrolyte were not critical. An aluminum cathode and two lead anodes were used at a cathode current density of 1.2 amperes per square decimeter.

Jan 1, 1959

By R. T. Dec

Current industrial compacting and briquetting practices are largely based on trial-and-error techniques. This paper introduces a two-dimensional finite element model of briquetting process in the roller press. Compared with other modeling techniques used in the past, finite element method offers the most versatile approach because it incorporates adequate information about powder behavior, geometry and frictional conditions and offers predictions for the density distribution, the velocity field, the stress distribution, roll force and torque. More over, when the model includes elasticity, it offers predictions on the internal stress state in the briquette after its exit from the roll. This enables to perform realistic computer experiments which are helpful for establishing the forming cavity geometry and process conditions necessary to produce briquettes with the desired properties. Three forming cavity profiles are analyzed. Results from model are verified on experimental roller press and best cavity profile is recommended for briquetting of sub bituminous coal fines.

Jan 1, 2014

The following is a Maintainability Design Checklist for coal mining equipment. The purpose of the checklist is to provide a summary of design review points for the maintainability assessment of new or existing underground equipment. It specifically focuses on the identification of equipment design features, tasks, or procedures that impact equipment downtime, repair costs, labor hours and maintainer skill level requirements. Some checklist points are general in nature. The checklist was designed to be used across all categories of underground equipment. The intent is to draw attention to design features and maintenance procedures that will increase maintainability requirements. You are encouraged to adapt this checklist to site specific or machine specific requirements by: ? Inserting specific performance criteria for various categories of maintenance tasks. For example; all hydraulic lines on a shuttle car should be replaceable in 15 minutes or 25 minutes, etc. ? Adding or deleting checklist items for different categories of equipment. You would include environmental control equipment, for example, on face equipment and not on shuttle cars or man trips. ? Adding additional checklist items based on site or equipment specific maintenance histories or experience, company maintenance standards, or other factors.

Jan 1, 2000

The following is a Maintainability Design Checklist for coal mining equipment. The purpose of the checklist is to provide a summary of design review points for the maintainability assessment of new or existing underground equipment. It specifically focuses on the identification of equipment design features, tasks, or procedures that impact equipment downtime, repair costs, labor hours and maintainer skill level requirements. Some checklist points are general in nature. The checklist was designed to be used across all categories of underground equipment. The intent is to draw attention to design features and maintenance procedures that will increase maintainability requirements. You are encouraged to adapt this checklist to site specific or machine specific requirements by: Inserting specific performance criteria for various categories of maintenance tasks. For example; all hydraulic lines on a shuttle car should be replaceable in 15 minutes or 25 minutes, etc. Adding or deleting checklist items for different categories of equipment. You would include environmental control equipment, for example, on face equipment and not on shuttle cars or man trips. Adding additional checklist items based on site or equipment specific maintenance histories or experience, company maintenance standards, or other factors.

Jan 1, 2000

THE Institute assembled in the rooms of the Geographical Society, Cooper Union, at 8 o'clock P.M., February 24th, 1874. President Barnard, of Columbia College, delivered an address of welcome, to which President Raymond responded. The Council then presented the following names, duly indorsed for election as members and associates. The gentlemen named were unanimously elected. *Bullock, M. C., - New York. †Burke, M. D., - Cincinnati, Ohio. *Burt, M. W., -Wheeling, W. Va. †Cameron, J. G. M., - New York. *Canfleld, Frederick A., - Dover, N. J. *Chandler, Prof. C. F., - New York. *Clayton, J. E., - Salt Lake City. †Colton, C. A., - New York. *Cooke, Prof. George H., - New Brunswick, N. J. *Cooper, Edward, - New York. *Dahlgren, C. B., - Mazatlan, Mexico. †Dutton, Capt. C. E., - Washington, D. C. *Eurich, E. F., - New York. †Fuller, H. L., - Woodside, Luzerne County, Pa. †Hamilton, S. Jr., - New York †Harnickell, A., - New York. *Hearne, F. J., - Wheeling, W. Va. *Hill, Samuel W., - Marshall, Mich. *Hulbert, Edward J., - Houghton, Mich. *Hunt, R. W., - Troy, N. Y. †lhlseng, M., - New York. *Iselin, Henri, - New York. *Janney, Morris P., - Pottstown, Pa. *Jenney, Frank B., - Brooklyn, N. Y. *Jenney, Walter P., - Brooklyn, N. Y. †Joy, D. A., - New York. *King, Clarence, - New York. *Kittoe, E. F., - Charleston, S. C. †Lawrence, Robert,. - New York. *Locke, J. M., - Cincinnati, Ohio. *McCormick, Henry, - Harrisburg, Pa. * Members. † Associates.

Jan 1, 1874

By Harovel G. Wheat

It has been shown that the incorporation of fly ash into concrete as a replacement for part of the cement can be beneficial. In some cases, the strength of the concrete can be increased and the permeability can be decreased. This latter property can lead to a reduction in the migration and/or penetration of aggressive species into reinforced concrete. Some of these species, such as chlorides from deicing salts or marine environments, can subsequently result in accelerated corrosion of the steel reinforcement, a loss of the protection provided by the passive film on steel, and a loss of structural integrity of the concrete. Care has to be taken so that the appropriate compositions of the components of the fly ash are utilized in order to ensure maximum benefit to the concrete structures. This will be discussed as it relates to fly ash generation and treatment.

Jan 1, 2002

By J. O. Brittain, E. Lautenschlager

Yield point measurements were made on polycrys-talline specimens of a iron deformed various amounts at 770, 1950, or 273°K, aged, and redeformed at 77: 195°, or 273°K. When the prestrain temperature is lower than that subsequent to aging, the yield point return is suppressed relative to specimens deformed at the same temperature both before and after aging. The degree of suppression is a function of both the magnitude of prestrain at the lower temperature and the difference between the deformation temperatures before and after aging. It is proposed that the suppression is caused by the formation of dislocation barriers during the initial low-temperature deformation. The aging kinetics of polycrystalline a-iron wires deformed at 77o or 303oK were studied at 44 " and 64 "C using internal friction measurements. No change was noted as a result of the difference in prestrain temperature. IN an earlier investigation1 it was observed that the return of the yield point was suppressed when a poly-crystalline specimen of a iron was plastically deformed at 77oK, aged at room temperature, and subsequently tested at room temperature. In order to investigate this observation, a research program was undertaken to measure the effect of prestrain temperature on the strain aging of a iron.' According to Thomas and Leak,3 return of the yield point and internal friction are similar measures of strain aging since both are dependent on solute atoms leaving the solid solution. The decrease in internal friction as a function of aging time is indicative of the removal of solute atoms from the solution, while the return of the yield point as a function of aging time gives the rate of arrival of solute atoms at the dislocations. According to Cottrell and Bilby,4 the solute atoms create an "atmosphere" which locks the dislocations and causes a return of the yield point upon restraining. In this experiment, both methods of measuring strain aging were employed in order to have two independent measurements of the strain aging phenomenon. In a previous study,5 the strain aging kinetics of a similar lot of a iron were measured for specimens which were prestrained and tested at the same temperature over the range of 77" to 273°K. Although some differences were found in the correlation of the two methods employed for measuring strain aging, the kinetics of strain aging were unaffected by the change of prestrain and test temperature. In another study,6 dislocation line tension and the density of the solute atmosphere were found to contribute to the return of the yield point when ingot iron specimens were prestrained at 303°K and tested at a lower temperature, namely 77°K. This paper is concerned with changes in strain aging kinetics produced by pre-straining at 77" to 303°K and testing at either the prestrain temperature or at higher temperatures up to 273°K. EXPERIMENTAL PROCEDURE The polycrystalline a iron specimens used in both the tensile and internal friction tests were 0.033-in. diam ingot iron wires, wet hydrogen treated and re-carburized. A more detailed procedure for processing a 3/16 in. ingot iron rod (nominal wt. pet composition: Fe - 0.013; C - 0.0125; Mn - 0.023; Si -0.005; P - 0.0023; S - 0.11; Cu - 0.004 N) to 0.033 in. diam specimens containing approximately 0.020 wt pet C and no detectable nitrogen with a grain diameter of 0.033 to 0.040 mm is given elsewhere.5 Immediately prior to testing, specimens were solution treated for 15 min at 700o ± 2°C in a static vacuum of less than 50 ?. of Hg and rapidly quenched into an ice-water bath while still enclosed in a 3 mm quartz vial. The internal friction specimens had 8-in. gage lengths and the tensile specimens had 2-in. gage lengths. The wires used as tensile specimens were first run as internal

Jan 1, 1962

By Arthur F. Taggart

PROGRESS in a technical art is of several kinds. It springs .from many diverse sources. It comprises invention, mechanical improvement, operating advance, analytical study, education. Invention is, by definition, a relatively great, essentially individual step, taken quickly. Operating advance is the slow, cumulated march of practice; in contrast, it moves at the pace of the tortoise, but over, the years its effects rival and, in some cases, surpass those of invention. Mechanical improvement- is a usual concomitant of the reduction of invention. to operating practice; thereafter it is a primary tool of operating advance. Analytical study is the process of mental digestion of the fruits of invention and practice. Its purpose is to render these into a form assimilable by the art as a whole, and by the perennial crop of would be practitioners. Education, disseminating the results of such study, consolidates and maintains the positions gained. Thus, slowly at first, but continuously accelerating, the tide of progress grows- to flood. Such growth, in mathematical parlance, is expressible in the general form y = mxn, where x is time, n is some positive number greater than one, m is another positive number, and y is the state of the action at instant x. When n is 2, the readers will recognize the graph of the equation as one branch of the familiar square parabola, whose property it is to become parallel to the y-axis; i.e., to move at an infinite rate, in that never-never

Jan 1, 1947

By E. C. Perkins

Preliminary experiments are reported utilizing bacteria to leach manganese from a variety of domestic low grade manganiferous materials. In two large leaches manganese extraction ranged from 71.7 to 92.5 percent, and the products analyzed over 48 percent manganese. Nutrient requirements and leaching time experiments were made. The mechanism of leaching is not understood, but is different than the mechanism encountered in the microorganism accelerated leaching of copper in the presence of sulfide minerals.

Jan 1, 1962

By R. A. Beall

As part of an ongoing program to develop high-quality materials with improved performance and service lives, and to conserve critical minerals, Bureau of Mines, U.S. Department of the Interior, researchers studied the process of hot-rolling metals, alloys, and composites in vacuum. First, a comprehensive review of the literature is presented, including the advantages and disadvantages of using vacuum. Next, details of hot-rolling titanium, chromium, and molybdenum-iron bimetal are given. Finally, the design of new equipment is described. At this time, it is uncertain whether hot-rolling metals in vacuum will gain commercial acceptance in the future.

Jan 1, 1979