Search Documents

By C. H. Riggs

"INTRODUCTION The injection of gas into the McClosky limestone in the adjoining, Griffin and New Harmony field in Indiana and Illinois and resulting increases in oil and gas production from this zone ore described in this report.Since 1911, the use of compressed air or as to increase oil production by supplementing natural reservoir energy has been widely adopted, and has resulted in the recovery of much additional oil, which otherwise would have been left underground. In many of the newer oil fields, including Griffin and New Harmony, a part of the compressed residue gas from natural gasoline plants is returned to the reservoir as a secondary method to increase oil and gasoline production. Part of the injected gas is stored underground for future use.By presenting data on many secondary recovery operations in a series of reports 5-9/ the Bureau of Mines has sought to stimulate interest in secondary recovery as a means of increasing oil recovery and current oil production for wartime needs. Most of the elder fields in the United States produce oil from sandstone reservoirs, and probably more than 90 percent of secondary recovery operations have been developed in oil bearing sandstones. During recent years, the volume of oil obtained by primary methods from limestone reservoirs has increased steadily, but as yet little has been done to recover, by secondary means,,the large volumes of oil left in limestone reservoirs when primary methods production are no longer profitable. Because of inherent differences in the origin and nature of the pore spaces between sandstones and limestones and because of differences in permeability and fluid content, secondary recovery methods, which are successful in sandstone-reservoirs, are not always applicable to limestones. Not much he been written concerning secondary recovery operations in limestone reservoirs, and few data are available to assist operators in developing such secondary recovery projects."

Jul 1, 1945

By J. Choi

For the first time, the influence of stearyl trimethyl ammonium chloride (STAC) as a collector, on the flotation behavior of lepidolite (Uljin, South Korea) was systematically examined in Denver Sub-A cells. Flotation tests were carried out by varying amount of STAC (50?200 g/ton), feed size (-65, -100, -150, and -200 mesh), and solution pH. The impeller speed of 1000 rpm, flotation time of 10 min and AF-65 (a frother) of 250 mL/ton were invariably applied. In order to complement flotation experiments, zeta potential measurements and XRD analysis were conducted. XRD results showed that the ores were mainly composed of lepidolite, muscovite, quartz, calcite and albite. In addition, zeta potential results showed that isoelectric points were about 2.5, 2.3, and 9.7 for quartz, albite, and calcite, respectively, and lepidolite was determined to be less than 2. Overall, the results of 3-stage flotation showed that Li2O grade and recovery tended to increase with increasing STAC dosage and decreasing feed size. In addition, Li2O grade increased with decreasing pH. The results were explained by the extent of the interaction between STAC and each mineral.

Feb 23, 2014

By Atsushi Shibayama, Toyohisa Fujita, Wan-Tai Yen, Ke-jun Liu

"In this investigation, a sponge gold sample (99.92% pure) has been leached with ammonium thiosulfate solution. The effects of CuSO4, (NH4)2S2O3, (NH4)2SO4, NH4OH and retention time on the gold leaching % (extraction %) and thiosulfate oxidation % (consumption %) have been studied. The copper ion acts as a catalyst in gold dissolution. On the other hand, it also accelerates oxidation of thiosulfate (consumption). It was found in this study that the best gold extraction condition was obtained at 43.2 ks with 0.8 - 1.0x103 mol/m3 (NH4)2S2O3, 30 mol/m3 CuSO4, 2.0 - 3.0x103 mol/m3 NH4OH, 0.4 - 0.5x103 mol/m3 (NH4)2SO4, pH 10±0.2 and 150 rpm. The thiosulfate oxidation was about 15% of the initial concentration.For gold recovery from the pregnant solution, the trioctylmethyl ammonium chloride (TOMAC) was used in this investigation as an extractant to extract gold from thiosulfate solution without pH and other adjustments. The effects of gold concentration, pH, ammonia, thiosulfate and cupric ionic concentrations, extractant and diluent concentrations and retention time on the gold recovery were investigated. It was found that 180 mol/m3 extractant diluted with n-octant at O/A ratio of 1:1 could extracted the 100% of gold in 0.6 ks from the thiosulfate solution at the optimal leaching conditions. The 100% gold stripping could be achieved with 10% thiourea solution."

Jan 1, 2003

By Cotton R. E, Cox R

Digger Rocks is one of several nickel-bearing sulphide deposits localised within komaLiitic volcanics of the Forrestania Greenstone Bell within the Archaean YiIgam Block of Western Australia. Exploration and evaluation to April 1990 have delineated a resource, at a nominal cut-off grade of 0.5 per cent Ni, of 1.9 Mt at 1.1 per cent Ni within a lensoid sulphide body which strikes NW, dips 50°SW, and occurs at a depth of 30 - 110 m below surface. There has been no production from any of the Forrestania nickel deposits to-date. The deposit, comprising both disseminated and massive sulphides, has maximum dimensions of 400 m strike, 115 m vertically and 90 m true width. Generally the massive sulphides occur at the base of the disseminated sulphides, on or close to the base of the Digger Rocks dunite. The two main massive sulphide lenses have maximum dimensions of 120 m strike, 75 m vertically and 16 m true width (northern lens) and 60 m strike, 25 m vertically and 4 m true width (southern lens). The average grades of the massive and disseminated sulphides are 5.9 per cent i and 1.2 per cent i respectively. The massive sulphides generally have sharp hangingwall and fOOlwall contacts and display strong internal grade anisolropy.The massive sulphides are mainly within the supergene zone and consist of violarite, pyrite and marcasite. The disseminated sulphides are mainly within the primary zone and consist of pentlandite, pyrrholite, pyrite and minor chalcopyrite. Alteration zones, up to six in number, are complex in detail. The sulphides are capped by an average of 30 m of sub-economic, leached, siliceous, oxidised material.A genetic model for the deposit is described which places Digger Rocks in Category 2 (sulphides in large layered dunite bodies) of the latest classification of komatiitic nickel sulphide deposits in the Yilgam Block of Western Australia by Hill and Gole (1990).

Jan 1, 1992

By E. G. Valdez

Laboratory research demonstrated that ceramic wall and floor tile can be produced from electric furnace phosphorus slags composed of calcium silicates. Grinding the slag in a pebble mill, followed by magnetic removal of deleterious magnetite, produced a raw material that could be compounded and formed into wall tile by dry pressing, sintering, and glazing. The effects of process variables such as forming pressure and sintering temperature were investigated. Wall tile bodies produced by this method were comparable to commercial tile. The tiles were readily glazed to a smooth shiny finish and met ASTM Specifications C34-62 for structural clay load-bearing tile. The estimated cost of producing wall tile by this method compared favorably with the retail market value for similar wall tile. Addition of borax or other additives to the ground slag followed by dry pressing and firing likewise produced a commercial grade of floor tile.

Jan 1, 1974

By Richardo Montoya

Radomiro Tomic, the new CODELCO division, is a copper deposit located at 3000 m a.s.l. and 40 Km from Calama in northern Chile. It has total oxide reserves of 802,000,000 tonnes with an average grade of 0.59% total Cu (using a cut-off grade of 0.4% total Cu). The copper oxide ore is mainly atacamite and chrysocolla. Startup is expected to commence in December 1997 of 150,000 t/y of Cu cathodes. Future expansion to 250,000 t/a of Cu cathodes is currently being planned. The process consists of an open-pit mine, a two-stage crushing system, agglomeration with sulphuric acid and emplacement on a heap leach pad for a 45-day leaching cycle. Solvent extraction and electrowinning will produce LME "A grade cathode. A number of significant technology innovations have been incorporated into the project.

Jan 1, 1998

By Aleksandar N. Nikoloski, Rorie Gilligan

Brannerite, UTi2O6, is the most common of the refractory uranium minerals and requires leaching under intense conditions to effectively extract the uranium contained within. Brannerite is often found together with apatite in metasomatic uranium deposits. Apatite and other phosphate gangue minerals can inhibit uranium leaching by generating phosphate ions which interfere with the reactions between acidic ferric sulphate and uranium minerals. As part of a detailed fundamental study on the leaching reaction mechanisms for brannerite, tests under a range of selected leach conditions were carried out with the addition of 10 g/L fluorapatite with the goal of identifying conditions where the negative effects of phosphate are reduced. Leaching was carried out for 5 hours with 0.05 mol/L Fe3+ as Fe2(SO4)3 with 0.25–1.00 mol/L H2SO4 and at temperatures between 25 and 96 °C. A single test was performed with 0.05 mol/L Fe3+ as FeCl3 and 1.00 mol/L HCl. In the sulphate system, the effect of phosphate was weakest at the highest acid concentration (1.00 mol/L H2SO4). In the chloride system, phosphate did not suppress uranium extraction, suggesting that HCl leaching could be a viable alternative for the leaching of high-phosphate refractory uranium ores.

Mar 17, 2021

By N. S. Greensfelder

THE firing of explosive charges by electricity dates back to 1745 when a Doctor Watson is said to have used an electric spark for igniting gunpowder. His method failed in practical application because, to ignite blasting powder, heat must be applied for a period longer than the duration of an electrostatic spark; Wheatstone found that this does not exceed 14000 sec. The usual result, therefore, of an electrical discharge in gunpowder is to scatter the grains, without igniting them. Benjamin Franklin partly overcame this difficulty by confining the powder and crushing grains that lay in the line of discharge. In 1822, after the primary cell had been discovered by Volta, Robert Hare, professor of chemistry at the University of Philadelphia, noticed the heating of a short piece of wire placed in the circuit of a voltaic battery. Later work by Oersted, Faraday, Wheatstone, and Henley resulted in the development of the magneto blasting machines. Fulminates of gold and silver are thought to have been discovered by Cornelius Drebbel, about 1600. Pepys, in his diary for November 11, 1663, recounts a conversation with Doctor Allen, who told him about aurium fulminans "of which a grain ... . put in a silver spoon and fired, will give a blow like a musquett and strike a hole through the silver spoon downward, without the least force upward.1," This fallacious belief that explosives act downwards only, is still held by many who should know better. Fulminate of mercury was discovered by Howard in 1799. J. Shaw of Philadelphia is said to have invented a fulminate-of-mercury cap in 1814; his idea was later adopted by gunmakers in England and France. The principal advantages of

Jan 9, 1922

By G. H. Edmunds, C. H. Mathewson

About fifty pages of Henry M. Howe's profound treatise, "The Metallography of Steel and Cast Iron," are devoted to twinning with special reference to the origin, nature and general significance of the Neumann bands in ferrite. Howe believed with Osmond and Cartaud1 that the Neumanns are mechanical twins and his careful observations leave no doubt that these straight-sided narrow bands habitually occur parallel to trapezohedral planes of form {211). Attempts to develop the structure of the bands by various methods SO that their identity could be established beyond question have not been conspicuously successful. Howe thought that they deflected slip bands. Some of the etching figures which have been developed within and adjacent to Neumann bands support the contention that they are twins. A good example of this effect in ferrite containing 0.6 per cent, of niekel and 1.3 per cent. of phosphorus, originally due to Harnecker and Rassow,2 was reproduced in the 1928 lecture before the Institute of Metals Division on twinning in metals.3 In this case, the sides of the figures might represent the traces of cubic planes laid bare by etching a properly oriented grain of ferrite, twinned along a plane of form (211). Our own observations in this direction may be represented by Fig. 1 which shows in a deeply etched cavity in the boundary region between a Neumann band and the original crystal two small crystal surfaces which resemble the faces meeting at a reentrant angle in the simple cube twinned along a bisecting plane of form (211) as sketched in Fig. 2. Rosenhain and McMinn4 in 1925, after a careful study of slip bands in ferrite containing Neumanns previously produced by shock, concluded

By C. E. Arthur

The Bureau of Mines has investigated the problem of radioactive contamination using nuclear explosives to fracture petroleum reservoirs in an attempt to stimulate production. It was concluded that some contamination of petroleum products will almost certainly occur. However) the degree of contamination cannot be predicted except by a full-scale experiment) since simulating the problem in the laboratory is economically impossible because of the extremely high temperatures and pressures that must be reached in extremely short time intervals if a reasonable analog is to result.

Jan 1, 1965

By M Chiquito, R Castedo, P Segarra, L M. López, J A. Sanchidrián, J Navarro

The aim of this work is to assess the performance of different constructive solutions against explosions on the strength of masonry walls. The solutions tested, namely an external metal mesh, a glass fibre film on the external face of the wall and a basalt fibre film located on the inner face of the wall, have low to medium cost and are originally designed for other purposes, like seismic protection. Four cubic boxes 3 × 3 × 3 m were built using each of the solutions and typical masonry blocks. In the tests, a spherical plastic explosive initiated in the centre was placed at scaled distance of 2.9 m/kg1/3, so that moderate damage would be caused on the wall. In order to assess the performance of the explosive, pressure gauges were placed at the wall and at different distances from the explosion. Additionally, vibrations were monitored with seismographs in the far field and a high-speed camera was used to estimate the shock wave velocity during the tests. The resulting damage has been evaluated on 13 points of the external wall of each box using a rebound hammer. Damage maps have been drawn for each wall based on these measurements and damage has been assessed inside the box considering the fragments mass launched during the test. The use of external metal mess leads to a decrease of 34 per cent on damage of the external wall and 38 per cent reduction of spalling. The use of a film in the inner wall provides a strong reduction on spalling.CITATION:López, L M, Segarra, P, Castedo, R, Sanchidrián, J A, Navarro, J, Santos, A P and Chiquito, M, 2015. Performance of different constructive solutions against explosions in full-scale masonry walls, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 819–824 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Lynn Huntsman

INTRODUCTION The Sunnyside mines of Kaiser Steel Corp. are lo¬cated on the west flank of the Book Cliff Range, a tongue of the Wasatch mountain range in Utah. The mines are 193.12 air km (120 air miles) southeast of Salt Lake City and 40.23 km (25 miles) east of the town of Price. The area has a semiarid climate with an an¬nual rainfall of 304.8 to 381 mm (12 to 15 in.) and a temperature range of -23.3 to 32.2°C (-10 to 90°F). The base of the Book Cliff Range is approximately 1981 m (6500 ft) in elevation with some mountain peaks in excess of 3048 m (10,000 ft) (Fig. 1). The Sunnyside mines were opened in the late 1890s and have been operated continuously since that time. Kaiser Steel leased the No. 2 mine in 1942 and pur¬chased the entire property in 1950. There are three mines adjacent to one another, each with its separate access, ventilation, and haulage. The three mines en¬compass an area extending 12.87 km (8 miles) along the outcrop and dipping northeasterly 2.41 to 3.22 km (11/z to 2 miles) into the Book Cliffs. During 1975, only the No. I and No. 3 mines were operating to sup¬ply 908 184.7 t/a (1,000,000+ stpy) of clean coal to the Kaiser Steel mill at Fontana, CA. Sunnyside coal is blended with coal from the Kaiser Steel mine near Raton, NM, and with purchased coal from noncompany sources to form the mix for the coke ovens. At that time, Sunnyside operated three longwall units and five to seven continuous miner units. Typical production for that time came from one miner unit pillaring an area not conducive to longwall mining; one or two miner units on construction or modernization projects, and the remaining units used to develop future longwall panels. Longwall mining has been a part of the Sunnyside scene since 1961 when the first panel was set up in the lower Sunnyside seam of the No. 3 mine. Through 1975, 27 longwall panels were mined (Fig. 2). Of the more than 47 173 604 t (52,000,000 st) of clean coal that were taken from the property through 1975, 6 350 292.9 t (7,000,000 st) were mined by longwall methods. Coal was brought to the surface in 4.5-t (5-st) mine cars and crushed to -152.4 mm (-6 in.) before entering the preparation plant. Coarse coal is cleaned by Baum jigs and fine coal (-28 mesh) is cleaned in flotation cells. The coal is reduced to 50.8 x 0 mm (2 x 0 in.) and belted to an aboveground storage pile with a ca¬pacity of approximately 113 398.1 t (125,000 st). The coal is gravity fed through two 1.52-m (5-ft) diam culverts directly into railroad cars, which pass beneath the storage pile through an arched excavation. Eighty-four 90.7-t (100-st) cars make up a unit train which makes the round trip to the steel mill in four days. Additional trains are scheduled in as demands dictate. Loading rates in excess of 13 607.8 t/h (15,000 stph) have been attained. Geology The coal seams of this area are of Cretaceous age and are classed as a medium volatile bituminous coal. coal, with a sulfur content less than 1 % and 6 to (20-mile) zone of the Book Cliffs, and this area is owned or under lease by either Kaiser Steel or US Steel. Coal in adjacent areas is noncoking but an excellent steam coal, with a sulfur content of less than 1 % and 6 to 7% ash. Sunnyside coal contains 40% volatile, 53% carbon, less than 1 % sulfur, and 51/2 to 61/2 % ash after washing. There are two minable seams throughout most of the Sunnyside property known locally as the upper and lower Sunnyside. Separation between the seams varies from less than 300 mm (1 ft) near the southern boundary adjacent to the US Steel Columbia mine, to over 12.19 m (40 ft) in areas of the No. 3 mine in the center of the Sunnyside property. The upper seam varies in height from 1.2 to 1.98 m (4 to 61/2 ft) while the lower seam varies in height from 1.52 to 4.28 m (5 to 14 ft) in areas of No. I mine where the two seams apparently come together. The majority of early work was con¬centrated in the upper seam which has a stronger roof and a lower sulfur content. When Kaiser Steel began mining the No. 3 mine in the early 1950s, it mined in the lower seam beneath the old workings with conven¬tional and continuous mining equipment. Numerous bounces and pressure points created by unextracted pillars and barriers in the upper seam made this a low¬production, high-cost mine and brought about the ad¬vent of the first longwall system. The first unit, while small by today's standards, successfully mined panels that had been all but given up and saved the mine from closure. There were areas that could not even be mined by longwall because of the erratic extraction in the upper seam. The system was successful enough to allow operations to gain access to and develop virgin areas of the upper seam. Development of longwall mining in the No. 3 mine has been confined to the upper seam since late 1964. With the almost complete extraction afforded by the longwall system, it is felt the lower seam can be successfully worked in future years (Fig. 3). In most of No. 1 mine, only the lower seam (or lower seam and upper seam combined) is minable, except in the northwest portion where a rock split has again separated the seam into two 1.83 to 2.13-m (6 to 7-ft) thick beds. In this area, the upper seam or upper split is being mined. The separation between seams at the present workings in this area varies from 0.609 to 6.1 m (2 to 20 ft). It is hoped that most of the lower split can be mined using shield supports and/or what¬ever new technology is developed in the coming years. The coal seams in this area dip to the northeast at an average grade of 10%. The dip near the outcrop reaches 22% and gradually decreases downdip. Over¬burden ranges from a few meters at the outcrop to 762 m (2500 ft) over some of the deeper workings. In the next several years, some overburden will be in excess of 914 m (3000 ft) as the lower mine workings extend ever deeper under the Book Cliffs. To cope with the

Jan 1, 1982

By H. Lyn Bourne

This is the sixth annual tabulation that gives mineral royalty information. This tabulation, like the previous editions, includes all of the earlier data plus more than 100 new entries. In addition to the royalty information, some entries show the cost of purchased reserves. An article in the December 1984 Kentucky Coal Journal could have far reaching applications. It explains that a banking firm examined the "reserve risk" as one of six factors for analysis when financing a coal project. The firm concluded that coal reserves in Kentucky are worth an average of $0.29/t ($0.26 per st) in-place. The banking firm based this in-place value on its examination of more than 50 leases. In-place value is especially important when trying to establish a mineral value for a given deposit. Ernie Lehman wrote to this author after last year's column appeared and he quoted the lease rates for lead and zinc on federal land. He states, from first hand information, that the leases are based on a percentage of net smelter return as follows: 4% for the first five years, 4.5% for the next five years, and 5% thereafter. The figures used in last year's column ($ per st) came from dividing reported royalty income by reported production. The information reported last year merely translates the results of the net smelter return (as written in the lease) to royalty income per ton to the US Government for the various years. Statistics from the Minerals Management Service of the Federal Government show that oil and gas account for 40% and 53%, respectively, of the Federal royalty income. Coal accounts for about 4% and all other minerals, the remaining 3%. Oil and gas leases are mostly at 12.5%. Most of the coal leases are at 12.5% for surface mining operations and 8% for underground mining. Many of the other commodities are leased at 5%, which has been true for decades. Relative to Federal leases, this year's table shows some percentages and some costs per ton. This was done to give information about the leases and also to show income produced by various commodities. Note that some commodities have a variation in $/ton even though the royalty percent is the same. These variations result from a combination of factors that influence the value of a mineral commodity. The same caveats that have appeared in previous columns relative to factors that influence the value of reserves are restated. The data in the table serve as a general reference and are not intended to present an absolute scale of reserves costs. Several factors influence the value of any mineral commodity. The factors include: • location/transportation (especially significant for most industrial minerals); • market conditions both for the commodity and the company acquiring the right to mine it; *quality or grade of the deposit as it reflects the amount of processing/beneficiation necessary to produce the finished product; and • legislative restrictions and conditions for mining a given material at a given site. These and other factors will significantly influence the cost of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity in column 1, and the subsequent columns give the location - either by state, US geographic area or Canadian province; the cost - R for royalty and P for purchased cost; and the year in which the lease or purchase agreement occurred. The last column offers either comments or gives a footnote number for more information. The cost column requires more explanation. The units may refer to cubic yards (/yd), cubic feet (/cu ft), tons (/T, 2000 lbs) or acres (/A). 1 cu yd = 0.7646 m3 1 cu ft = 0.2832 m3 1st=0.9078t 1 acre = 0.4047 hm or m2 In several cases, the royalty is a percentage of the sales price of the finished product and is levied against either the amount produced or the amount sold. We thank those who contributed information for the table: G. Anderson, B. Brown, R. Ganis, K. Hauser, E. Lehman, and S. Sims. Their help is appreciated as are the contributions by those who asked to remain anonymous. This column requires additional information each year. That data must come from people in the minerals industry who have royalty information. What appears in the table is only a very small fraction of the cost information relative to the various commodities and the geographic areas for which there is royalty information. If you find this column of interest and possess information write the author at the address given in the author's box or call 313-462-0005.

Jan 7, 1988

By S. N. Sinha

The distribution coefficients of lead and silver between copper and matte phases have been measured at two different temperatures. Experiments covered the ranges of 0.009-1.8, 0.07-0.13, and 0-11 wt pct lead, silver, and iron in matte, respectively. The distribution coefficients of lead have been measured at 1405 and 1505 K and correlated with lead and iron concentrations in metallic copper and matte. The values of the distribution coef¬ficient of lead between copper and iron-free matte, at infinite dilution of lead, have been determined to be 3.60 and 4,06 at 1505 and 1405 K, respectively. The distribution coefficient of silver between copper and iron-free matte is independent of silver concentrations and has been measured to be 2.13 and 2.21 at 1400 and 1500 K, respectively. For an iron-bearing matte, the distribution coefficient of silver has been correlated with iron concentration in the matte at both 1400 and 1500 K. From the measured values of distribution coefficients, the Raoultian activity coefficients of PbS and AgS0.5 in copper-saturated matte have been calculated. At infinite dilution, the following equations correlating the Raoultian activity coeffici¬ents of PbS and AgS0.5 with matte- composition and temperature have been obtained: log Y° PbS =1.515 + 1080/T 0.14 NFes lbS Fog YAgS = -0.074 - 425/T + 0.09 NFes. - 0.5

Jan 1, 1983

By J. F. Strunk Jr., K. M. Maestas, Y. Chai, R. Legrand, R. L. Henry

"Groundwater with elevated sulfate and metals was treated using a sulfate-reducing pilot PRB consisting of a series of six 55-gallon drums filled with ZVI (Fe0), wood chips, brewer’s grain, limestone, and emulsified vegetable oil (EVO). Sulfate was reduced from >3000 to <250 mg/L and Cd, Cu, Mn, Ni, and Zn concentrations declined up to 3 orders of magnitude in 2 months. After 6 months of operation at a 7.5-day retention time, sulfate broke through. The system was then rejuvenated by injecting EVO in each drum and operated for 5 more months at a 9-day retention time. Sulfate-reducing bacteria in the pilot system grew by 3 to 4 orders of magnitude in 2 months. Some cementation of the PRB media was observed in the first 2 drums after processing 25 pore volumes of water, due to preferential upstream precipitation of sulfides; this can be avoided through operational modifications. Resulting permeability losses were estimated at 0.1% to 1% per year. Absorption/desorption was tested at bench scale to evaluate the use of various oil-soaked sorbents as a slow-release source of dissolved carbon. The tests show that oil sorbents can increase the useful life of a PRB between oil refills to over 100 pore volumes. INTRODUCTION High sulfate concentrations, low pH, and dissolved metal exceedances are common characteristics of mining-influenced water (MIW). Above-ground such MIW is commonly treated using biochemical reactors (BCR). In a BCR, water generally flows vertically downward through a layer of biomass, such as wood chips, manure, etc. The dissolved organics resulting from the decay of this material are oxidized first by microbes using oxygen; when oxygen is exhausted, other bacteria can use nitrate, and then sulfate to oxidize organics. Sulfate-reducing bacteria (SRB) reduce sulfate to sulfide, which quickly reacts with metals to form largely insoluble and stable metal sulfides. These reactions can be summarized as follows:"

Jan 1, 2016

WELCOME to the world-class Cripple Creek district where gold exploration and production continue 95 years after the initial discovery. More than 21 million troy ounces of gold have been recovered, valued at greater than $7.8 billion using today&apos;s gold price ($371/oz). The Cripple Creek district is localized within and around the margins of a silica-undersaturated alkalic diatreme-intrusive complex. The diatreme appears to be comprised of three sub-basins: 1) a sub-basin east of the Cresson (Fig. 1); 2) a southwestern sub-basin between Victor and Cripple Creek; and 3) a northwestern sub¬basin within which the Globe Hill and Ironclad pits (Fig. 1) are located. The recognition of three separate basins was made by G. F. Loughlin and A. H. Koschmann (1935, Fig. 8) who prepared a contour map on the floor and walls of the composite Cripple Creek basin. The northwestern and southwestern sub-basins are apparent due to the discontinuous exposures of a partially exhumed ridge of Precambrian rocks (Fig. 1). The separation of the eastern and southwestern sub-basins was recognized in mine exposures where a fault-bounded ridge line extends from the vicinity of the Ajax mine toward the Precambrian "island" (Fig. 1).

Jan 1, 1986

By F Shi, W Huang, D Seaman, K Runge

High Voltage Pulse (HVP) technology is a novel process that could potentially be the step-change needed in ore processability in the mining industry. The propensity of high voltage pulses towards mineral-enriched ore particles during treatment makes this technology selective and has the potential to enable ore pre-concentration by size separation. In this study, the potential for pre-concentration of a low grade copper-gold ore sample subjected to HVP pretreatment is investigated and compared to that achievable after mechanical breakage in JKMRC’s rotary breakage tester (JKRBT). The data show that a better pre-concentration result can be achieved after HVP processing than conventional breakage. The gold pre-concentration potential is much better than that observed for copper. 4D HVP pre-concentration characteristic curves were produced to assess the metallurgical performance possible as a function of energy input. The case study shows that when targeting a nominal metal recovery of 90 per cent for gold, the HVP pre-concentration technique can split the low grade ore (0.9 ppm gold and 0.28 per cent copper in the feed size 26.5-37.5 mm) into two components – a low grade oversize material (0.3 ppm gold and 0.15 per cent copper) and a high grade undersize material (1.0 ppm gold and 0.3 per cent copper). The mass split to the low grade is 23 per cent. Under this mass split scenario, gold recovery to screen undersize is 90 per cent and copper recovery is 85 per cent. The HVP treatment of this feed size requires a specific energy (spark) of 2.8 kWh/t.There is further research that would be required before industrial uptake of the HVP pre-concentration technology would be possible. This paper also outlines the research challenges that need to be overcome.CITATION:Huang, W, Shi, F, Antonio, C, Runge, K and Seaman, D, 2018. High-voltage pulse pre-concentration study using a low-grade copper-gold ore, in Proceedings 14th AusIMM Mill Operators&#39; Conference 2018, pp 327–338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

AMOS PEASLEE BROWN Amos P. Brown, Professor of Geology and Mineralogy at the University of Pennsylvania, and a member of the Institute since 1888, died at Atlantic City, Oct. 9, 1917. An extended biography, by his classmate and lifelong associate, Witmer Stone, was published in the Proceedings of the American Philosophical Society, Vol. 57&apos;(1918), from which the following brief extracts have been taken. For want of space, we must omit reference to Professor Brown&apos;s extensive and valuable work on botany, zoology, paleontology, and physiology, to the latter of which sciences lie applied the methods of microscopic crystallography with striking success. Amos Peaslee Brown was born in Germantown, Philadelphia, on Dec. 3, 1864, the son of Amos Peaslee and Frances Brown, and the fourth child of a family of seven sons and two daughters. His earliest education was received at a small private school, but in the autumn of 1877 he entered the Germantown Academy. Deciding to take a scientific course in college he did not study Greek, and dropped Latin in his last years at school. He was thus able to graduate in June, 1852, entering the University of Pennsylvania the following autumn. He took the Towne scientific course, specializing in mining engineering after the sophomore year. He studied mineralogy under Prof. George A. Koenig, chemistry under Prof. Frederick A. Genth, physics under Prof. George F. Barker, astronomy under Prof. E. Otis Kendall, civil engineering under Prof. Lewis M. Haupt, mathe-matics under Prof. Henry W. Spangler and botany under Prof. Joseph T. Rothrock. He graduated in June, 1586, receiving the degree of B. S., and was chosen to deliver the bachelor&apos;s oration at the commencement at the old Academy of Music. He remained at the University another year, taking the post-graduate course in mining, and received the degree of E. M. in June, 1887. Soon after graduation, Brown secured a position as aide on the Second Geological Survey of Pennsylvania, under Ashburner, his first work consisting in the compilation of data respecting the coal-mining operations of the State. This occupied a year, mostly in the field, followed by office work in Pittsburgh. Finishing his work in the bituminous region in June, 1885, Brown returned to Philadelphia and accepted a position under Mr. Benjamin Smith Lyman, who had undertaken a survey of the New Boston and Morea coal lands in Schuylkill County, near Pottsville. The survey was a private enterprise, but the map was afterward published by the State Geological Survey. This work kept Brown in the field until late in the autumn, while the actual drawing of the map was. done in Philadelphia in the winter. In the following spring Mr. Lyman engaged in a survey and report on the "New Red" formation of Bucks and Montgomery Counties, in which Brown again acted as his assistant and prepared an account of the igneous rocks of the district, which accompanies Air. Lyman&apos;s report. His name appears on both the Bucks County map and that of the Morea anthracite district.. In the early autumn of 1889, before the Bucks County survey was completed, Brown left Mr. Lyman to accept a position as instructor in mining at the University of Pennsylvania, under his old professor, Dr. Koenig, and here lie remained for practically the rest of his life. In 1890 lie was instructor in mining and metallurgy; in 1892 professor of mineralogy and geology in the auxiliary department of medicine, which he held until the abolishment of the department in 1898. On March 5,1895, he became assistant professor of mineralogy and geology in the college faculty, and full professor in the spring of 1903, a position which he continued to hold until the spring of 1917, when he was forced to resign on account of failing health. From the autumn of 1892, after Dr. Koenig&apos;s retirement from the University, Brown took over the entire direction of the department, teaching in all branches of the subject-mineralogy, geology, lithology, crystallography, mining, and metallurgy. Soon after his return to the university he began studying for the degree of Doctor of Philosophy, which was conferred upon him on June 16, 1893.

Jan 9, 1918

By J. C. Reed

CINNABAR was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigel1 by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County-across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done con-siderable exploration work and has retorted the high-grade ore so .obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district.

Jan 1, 1935

By Leonard N. Hill

Cyprus Sierrita Corp. has 16 parallel 5.03 m-diam x 5.8 m long (16.5 ft-diam x 19 ft) primary ball mills, each operating in closed circuit with a nest of cyclones. Before the upgrade to 840 mm (33 in.) cyclones, each mill operated with a nest of five 660 mm (26 in.) cyclones - four in use and one on standby. In this configuration, the mill throughput was 88.5 kt/d (97,500 stpd). Flotation feed averaged 25.9% +212 pm (+65 mesh). The 660 mm (26 in.) cyclones normally operated at an inlet pressure of 34 kPa (5 psi), lower than the inlet pressure of 55 kPa (8 psi) recommended by the manufacturer. The circuit was typically operated with cyclone overflow densities greater than 40% solids to achieve the required throughput. This resulted in inefficient cyclone operation and excessive coarse oversize reporting to flotation. The apexes choked frequently. Larger apexes were tested but reduced the classification efficiency and resulted in circulating loads greater than 800%.

Jan 1, 1994