Search Documents

By N. R. Allen, J. D. Steenkamp

Oxidative roasting is applied on an industrial scale to beneficiate ilmenite concentrates from South African East Coast heavy minerals deposits - the aim is to increase the magnetic susceptibility of ilmenite to allow magnetic separation from chromite. The intention of this paper is to give researchers new to the field an overview of the beneficiation of ilmenite through roasting and magnetic separation, touching on the relevant fundamental aspects of magnetism.

Jan 1, 2005

By H. T. Kennedy, S. G. Dardaganian, J. L. Clanton

This paper presents equilibrium ratios measured on oil and gas samples taken from the Kelly-Snyder field at the reservoir temperature of 128°F. From these data smoothed curves were constructed for the reservoir fluid up to the bubble-point, 1,874 psia. A material balance calculation, based on the use of equilibrium ratios instead of the usual solubility and shrinkage meayr~rements is made on the field and compared to the con\.entional method. DETERMINATION OF EQUILIBRIUM RATIOS The equilibrium ratios, or K values were obtained by recombining separator samples of oil and gas taken when the reservoir was above its bubble point, and thus represented the reservoir fluid before any change had occurred due to the evolution of gas. The well sampled had a gas-oil ratio of 617 cu ft of high pressure sepalator gas per barrel of separator oil. and a bottom-hole temperature of 128°F. Samples were brought to equilibrium by agitating for 24 hours in a thermostat, maintained at the proper temperature within 0.2ºF, mercury being added when necessary to maintain the pressure constant. Samples of oil and gas were then taken by constant pressure displacement, and analyzed by low temperature frac-tionation. Equilibrium ratios were determined at 128°F and 500, 800, 1,000 and 1,400 psig. At the latter pressure, there were indications that the gas samples were contaminated with small quantities of oil, and only data taken at the first three pressures were included in Fig. I. This figure has been extended to higher and lower pressures by the use of the Fluor charts for 3,000 psi convergence pressure, on which the experimental points fit well. MATERIAL BALANCE EQUATIONS The possible errors involved in conventional material balance equations have been analyzed by Muskat1. Where the errors occur in field measurements, or in obtaining effective averages from variables such as gas-oil ratio and pressure, they will evidently be involved in any attempt to estimate the content of the reservoir. On the other hand, substantial errors may be introduced in conventional material balance calculations by: (1) the neglect of the amount of oil dissolved in gas at high pressures and temperatures in the reservoir, but which condenses under separator conditions; (2) the assumption that the separation of oil and gas in the reservoir may be duplicated by a differential liberation in the

By A Bouazza, J Kodikara

In this study, 23 samples of leached ash (LA) were collected from an ash pond at Loy Yang Power Station and geotechnically characterised. The samples were collected at various depths and locations within the ash pond on two separate occasions in order to account for the full variability. The LA within the ash pond at Loy Yang Power Station (LYPS) was found to vary in texture from silt to sand, depending on the location from where the sample was collected. Samples collected near the ash pond inlet discharge point, for instance, contained more than 50 per cent sand sized particles and were subsequently classified under the Unified Soil Classification System (USCS) as silty sand (SM). Further downstream of the inlet discharge, the LA became progressively finer and was classified accordingly as elastic silt (MH) when the sand content became less than 50 per cent. Basic geotechnical testing revealed that the LA from Loy Yang Power Station was generally acceptable as a landfill cover material. The permeability of LA, however, was generally too high for prescriptive covers, (ie resistive covers that generally rely on the impervious nature of the material to control percolation). Alternative covers, generally rely on the store/release function of a capillary or monolithic barrier to prevent percolation into the landfill. Subsequently, a material that can maintain a high water storage capacity while at the same time, readily allow infiltration and evapotranspiration is required for an alternative cover. Sandy silt and silty sand are optimal soils for alternative covers, as they do not yield water to gravity forces, but do give up most of the water in their pores when subjected to high-matric suction (Kavazanjian, 2001). The effectiveness of alternative covers is ultimately assessed using computer models, such as UNSAT-H and HYDRUS-2D, to rigorously perform water balance calculations. Prior to using a computer model to determine the highest possible percolation in the worst climatic conditions, it is necessary to select the most appropriate materials. This paper suggests a method to screen available materials for use as an alternative cover material on the basis of the soil water characteristic curve (SWCC).

Jan 1, 2003

By Andrea Koschinsky, Peter E. Halbach, Margret Halbach, Andreas Jahn

"Ferromanganese crusts contain hydrous Mn and Fe oxides as main metal compounds together with some economically interesting minor elements such as Co, Ni, Ti and Cu and trace metals such as Mo, W, Nb, Te, Ga, Pt, and REEs. Some of these metals or semimetals have a great future potential as innovative high-technology constituents. All of them are highly enriched in the crusts compared to seawater composition.The Mn in the crusts mainly originates from the O2 - minimum zone in the oceanic water column. The agent for Mn2+ oxidation is dissolved oxygen, transported upwards from colder deep water layers by turbulent eddy diffusion. The Mn itself descends from surface waters and is carried down to the O2-minimum zone by fecal pellet transport. In contrast, Fe is mainly supplied from carbonate dissolution of planktonic skeletons in the water column. These relationships result in the fact that the oceanic water depth strongly controls the metal composition of ferromanganese crusts: the Mn - group metals are more enriched in shallower water, whereas the concentration of the Fe - group metals increase with water depth. The REEs play a very important role with regard to the trace metal composition of the crusts: their concentrations increase with water depth mainly controlled by a decreasing Mn/Fe ratio.In seawater, REEs occur as carbonate complexes; preferably, the light rare earth elements (LREEs) form REECO3 +(aq) and the heavy Rare Earth Elements (HREEs) REE(CO3)2 (aq) complexes. The REEs are transition metals, their 6s orbital of the outermost shell is filled before the filling of lower 4f electron shells is completed, thus the configuration of the valence electrons is similar in all the REEs, and all REEs exhibit similar chemical behavior and exist, dominantly, as 3+ cations. The ionic radius decreases progressively from La3+ (1.18 Å) to Lu3+ (0.97 Å), this phenomenon is called "lanthanide contraction". Due to the fact that REEs in seawater form cationic and anionic carbonate complexes, the two main hydrogenetic constituents, hydrous !-MnO2 and Fe-oxyhydroxide, fractionate the group of REEs by surface absorption processes. According to the pHZPC-concept the ?- MnO2 phase has an electronegative surface, and Fe-oxyhydroxide a slightly positive surface charge at seawater pH. These relationships are the main reason for the observed REEs fractionation."

Sep 1, 2014

By Lex L. Udy

Properties of an explosive which itiuence its performance on rock breakage are analyzed in relation to the rock: hardness and a discussion on the interaction of an explosive with the rock during the blasting process is given. Theoretical concepts regarding ideal and non-ideal detonation are reviewed to explain how the physical and chemical factors of an explosive influence the rate of energy release and its consequence on blasting performance. While a lower velocity of detonation indicates a slowed chemical reaction it does not necessarily mean a loss in energy from the explosive. High density ammonium nitrate (HDAN) can be used effectively in the formulation of modern industrial explosives to slow the energy release rate with its attendant decrease in detonation velocity. Examples of blasting performance using custom formulated explosives with HDAN are presented.

Jan 1, 1995

By Swapan Ghosh, Amitava Sengupta, Proloy Das

Ferro-alloys are very important ingredients used for making of quality steel with desired composition. In view of high demand in various types of ferro-alloys, it has become necessary to produce the same efficiently, safely and cost-effectively with consistent quality maintaining the anti-pollution norms. To achieve this goal, it is necessary to adopt latest process/equipment with the state-of-the-art instrumentation and automation system. A Programmable Logic Controller (PLC) based automation system with suitable Human Machine Interface(HMI) terminals along with intelligent field mounted sensing/control devices allows to monitor and control the complete plant effectively with optimum deployment of man-power. In association with this, use of process optimization controllers enables to achieve specialised functionalities of the submerged arc furnaces like material management, lining management, electrode management, power management, overall production management etc.

Jan 1, 2007

By Joseph L. Young, Richard A. Bohling

To keep Homestake's Bulldog Mountain silver and lead mining and milling operation in southwestern Colorado workable, natural ground water and decant water from the mine's sand backfilling operation must be continually pumped from the workings. Left untreated, this water exceeds maximum allowable levels for various contaminants that may be discharged to the environment. To comply with regulations, a National Pollutant Discharge Elimination System (NPDES) permit was obtained and a mine water treatment plant for heavy metals removal was constructed in 1977. Due to equipment capacity and operational problems, and the lack of on-site technical personnel and analytic equipment, the first water treatment plant could not consistently meet permit limits. In 1979, Homestake entered into a consent decree with EPA and the Colorado Department of Health, calling for the construction of a water treatment facility to meet NPDES permit limits. Initial construction began in the spring of 1980 and the plant now produces effluent acceptable for discharge.

Jan 12, 1981

By Greg Wieland

Deep sewer tunnels are required to meet future growth demands of the City of Austin?s down-town redevelopment. The tunnel is 18,000 ft long and varies in finished diameter from 54 inches to 96 inches. The tunnel crosses under Austin?s Town Lake three times and there are four main work shaft sites. Geology, groundwater, foundations, downtown redevelopment, and an active, healthy community put significant constraints on the design. This paper discusses a major underground project for downtown Austin and discusses the risk considerations and the opportunities the design team took toward optimizing the project design for the construction phase.

Jan 1, 2008

By Daniel Barkley

Underground coal mining in Illinois has a lengthy history dating back to the early 1800?s. High extraction underground mining has played a significant role in production through out this time. Modern mechanized longwall mining methods were introduced in the 1960?s and have been in continual use ever since. Regulations governing subsidence from underground coal extraction and the mitigation of resulting impacts to surface structures and surface land initiated in 1983. Despite the history of experience with subsidence, recent plans to longwall in Illinois have stirred public emotions and strong opposition. Anti and pro longwall groups formed and divided a community over the potential economic benefits new mining ventures could bring verses the potential problems associated with longwall mining in productive flat farmland. The debate culminated in a county wide referendum vote on the use of longwall mining. This paper provides an overview of the history of underground mining in Illinois, the controversy that has risen in central Illinois regarding longwall mining, and the efforts to educate the public about regulations that govern longwall subsidence.

Jan 1, 2007

A physical modelling study has been carried out to simulate the slag-metal dispersion induced by a high-strength bottom gas injection. Water and kerosene were utilized to simulate metal and slag respectively. A water model of CLU (Creusot-Loire Uddeholm) vessel was used with three different nozzle orientations, namely, off-centre, triangular off-centre and centre. The gas flow rates changed from 0.00599m3/sec to 0.01081m3/sec. Height of heavy and light phases was kept fixed at 0.23 m and 0.02 m respectively. The dispersed phase holdup was determined at various axial and radial distances, gas flow rates, and tuyere configurations. The observations revealed that at a fixed gas injection rate, as the vertical distance increased in the centerline, straight off-centre orientation resulted in greater dispersed phase hold up values than those of the centre configuration and the triangular off-centre orientation. The dispersed phase holdup was found to increase with gas injection rate and decreased with axial distance. The variation of the dispersed phase hold up with the dimensionless axial distance and the gas injection rate was correlated by using the Modified Froude Number. The experimental values of the dispersed phase holdup were found to be in good agreement with the correlated values obtained from the modelling equations. The findings of the present study may be utilized in the ferroalloy refining vessels in terms of designing tuyere locations for optimum processing conditions.

Jan 1, 2004

By António A. Henriques, António Gomes Correia, Ana Teixeira

"Abstract Pile foundations are often used for important structures, and thus, reliability evaluation is an important aspect of the design. Reliability methods have become increasingly important as decision support tools in different areas. The main benefit of reliability analysis is that it provides quantitative information about the parameters (uncertainties) that most significantly influence the behaviour under study. In particular, the design of pile foundations still involves many limitations and uncertainties, particularly when there is not enough investment in soil characterisation and/or pile load tests. In addition to the uncertainties associated with soil characterisation, physical, statistical, spatial and human uncertainties exist. In this subject, the primary purpose of this paper is to demonstrate the application of reliability methods to geotechnical pile design (axial load). It also presents a simple and practical approach to performing it using Monte Carlo Simulations, intending to provide knowledge for code harmonisation and encouraging the development of such methodologies in geotechnical practice. Sensitivity analyses are shown to understand the influence of each uncertainty type coming from different sources. An application example indicates, corroborating other studies, that the model error is the most influent uncertainty. As such, when using the different models (SPT-, CPT- and PMT-based) for bearing capacity, the results emphasise the need for a well-defined and wellcharacterised resistance model, also these results allow the engineer to understand how important the load tests can be to achieve reliable results and economic designs.1 IntroductionUnlike the approach to reliability evaluation used in structural engineering, the traditional procedure used in geotechnical designs addresses uncertainties through high global or partial safety factors (SF), mostly based on past experience. However, this approach to addressing uncertainties does not provide a rational basis for understanding their influence on design.Furthermore, the new regulation codes and social concerns, such as the sustainability or the economy, are imposing geotechnical engineers to increase their ability to deal with uncertainty in a direct and more rational way. Designs should be economic, sustainable and reliable at the same time. Concerning the reliability part of design, different approaches can be done, but the most important thing to keep in mind is the simplicity and efficiency of the tools and applied methods."

Jan 1, 2014

By M. L. Bakker

Keywords: Pyrometallurgy, top submerged lance (TSL), nickel, PGM, calcium ferrite, lime ferrite The ISASMELT? top submerged lance (TSL) bath smelting process was developed in Mount Isa, Australia by Mount Isa Mines Limited (now a subsidiary of Xstrata plc) during the 1980s. By the end of 2011, the total installed capacity of the ISASMELT? technology will exceed 9 000 000 metric tons per year of feed materials in copper and lead smelters around the world. Commercial plants, operating in Belgium and Germany, are also batch converting copper materials in ISASMELT? furnaces. This TSL technology is equally effective for continuous converting processes, whereupon it is called ISACONVERT?. This paper presents the recently patented ISACONVERT? process for the continuous converting of nickel and Platinum Group Metal (PGM) containing mattes using the calcium ferrite slag system. The paper focuses on the potential application of the ISACONVERT? technology to existing nickel and PGM smelting complexes.

Jan 1, 2011

By Seong- Rin Lim

Light-emitting diodes (LEDs) are regarded as environmentally friendly light sources due to their high energy efficiency and lack of mercury content. LEDs are used for a variety of domestic and commercial lighting systems, where they are replacing incandescent and fluorescent lamps at a rapid rate. Incandescent lamps inefficiently consume energy because electricity is mostly converted to heat rather than light. This causes unnecessary environmental impacts and energy consumption associated with power generation and transmission from a life cycle perspective. Although fluorescent lamps are more energy-efficient than incandescent lamps, their disposal at end-of-life presents special challenges because of the presence of toxic mercury. Despite the seemingly apparent advantages of LED, very few studies have rigorously addressed potential environmental consequences of their disposal. Specifically, LEDs are designed with III-V semiconductors that presumably consist of toxic and rare materials, including arsenic, gallium, and indium. We hypothesize that, depending on their concentrations and leachability, these constituents may also contribute to render LEDs as hazardous waste at the end of their useful life.

Jan 1, 2010

By Stephen E. Mosher, Suzanne D. Smith

Ground, air, and water vehicles can expose humans to substantial multi-axis vibration. Multiple input/multiple output relationships or models exist for estimating frequency response functions of linear systems1, 2. These relationships have been applied by some investigators to evaluate the effects of occupied seat vibration3, 4. Using a multiple input/single output model, this study investigated the effects of single- and combined-axis vibration in the fore-and-aft (X), lateral (Y), and vertical (Z) directions on vibration transmission to the human chest. Frequency response functions (transmissibilities) were estimated and compared for the back-on and back-off postures. Methods A rigid seat with seat back was mounted onto the Six Degree-of-Freedom Motion Simulator (SIXMODE). A flat acceleration vibration signal was generated between 2 and 40 Hz at 1.0 ms-2 rms in the single and combined X, Y, Z, XY, XZ, YZ, and XYZ axes. The signals were shifted in time so that the combined inputs were not fully correlated. Lightweight triaxial accelerometers were used to measure accelerations at the seat base (input) and at the bony manubrium of the chest (output). The maximum of nine frequency response functions (H(?)) or transmissibilities were estimated from the auto- and cross-spectra. The system transfer matrix for the XYZ inputs and chest Z output is [ ] where PxZ, PyZ, and PzZ are the cross-spectra between the three inputs at the seat base and the Z output at the chest, respectively, and Pxx, Pxy,…zz are the auto- and cross-spectra between the input signals (? not shown in Eq. 1). Equation 1 can be similarly written for the chest X and Y outputs. Matlab® was used to estimate the auto- and cross-spectral densities for calculating the transmissibilities, ordinary coherences (for single inputs), partial coherences, and multiple coherences. Results Figure 1 illustrates the major chest transmissibilities observed for the two postures. Vertical vibration showed a consistent influence on the chest X response (Chest X/Z), most likely causing chest pitch. Some chest Z responses were observed with X-axis inputs, but the results were variable and difficult to interpret. In general, other factors besides the known inputs did not affect the transmissibilities shown in Figure 1 (Repeated Measures ANOVA, P<0.05). This was

Jan 6, 2006

By S. Finsterle, R. C. Trautz

We performed numerical modeling studies to investigate water seepage into underground openings excavated in unsaturated fractured rock. Water seepage is a key factor affecting the performance of a nuclear waste repository such as the one proposed at Yucca Mountain, Nevada. The amount of water dripping into an underground opening depends on the connectivity and permeability of the fracture network as well as on the capillarity of individual fractures intersecting the opening. We developed a high-resolution numerical model of an unsaturated fracture network and examined the appropriateness of seepage predictions using a fracture-continuum model. Model calibrations to liquid-release tests performed at Yucca Mountain are also discussed.

Jan 1, 2000

By Simon W. Houlding

The mining community is geographically remote and widely dispersed. There is a growing requirement for formalized professional development of members by professional associations, and increasing recognition of the advantages of continuing education and training by both individuals and corporations. Working against these trends are the increasing expense and time commitments required for attendance at conventional courses and workshops. The result is a perceived need for a readily accessible source of continuing education and technical reference on the Internet. The design constraints for an Internet model for professional development include: ? browser compatibility, with any time, any place, any pace accessibility; ? a content presentation model with low bandwidth requirements, appropriate interactivity for examples, tools and reviews, and viewer performance monitoring capabilities; ? formal accreditation of content, presentation and process so that viewer achievements may be formalized in terms of widely recognized Continuing Education Units; ? availability of tools for conversion of source material to the presentation format with minimal effort. A model that meets the design constraints is presented and illustrated by examples from an existing Internet site for continuing education in mining.

May 1, 2002

By C. Righi, R. Carli

In modern steel continuous casting technologies mould fluxes are well-known to assure lubrication required by tribological system of mould-solidifying strand shell, and to provide crystalline phase solid film, contributing to control heat extraction between strand and mould wall. Actual cooling rates during normal continuous casting mould operations are far higher than critical cooling rate of the liquid slag. Indeed, DTA measurements point out that even relatively small cooling rates of 30?50 K/min are high enough to give exiguous formation of crystals. In this paper, contribution of devitrification in defining crystalline phase formation of industrial basic mould slag, used in continuous casting of crack-sensitive steel grades, has been investigated by means of non-isothermal experiments study. Devitrification has proved to play a major role in mould flux crystallization in a working environment explaining the higher amount of crystalline phase formed in plant sample in comparison with lab sample from DTA analysis with typical cooling rate of 5?20 K/min. The amount of crystalline phases formed ranks as follow: Cuspidine > Combeite > Gehlenite. Kinetic analysis of DTA non-isothermal experiments has provided kinetic parameters through Kissinger and Ozawa methods, as Avrami constant resulting to be n ?2 and activation energy of Cuspidine crystallization resulting to be EC= 315 kJ/mole. The effect of addition to the parent material of oxides as MnO, TiO2, ZrO2, Al2O3 and Fe2O3near to saturation point has proved to affect, in certain cases, crystallization behaviour of mold flux. In particular, MnO, TiO2, ZrO2oxides produce a relevant dump of crystallization of Combeite and Gehlenite phases, while Al2O3and Fe2O3do not appreciably affect crystallization. Key words: Mould flux, crystallization, devetrification, DTA non-isothermal analysis, Kissinger and Ozawa methods.

Jan 1, 2004

By Juan Lizana

El presente trabajo describe el proceso del sistema de gestión estratégica en la mina San Rafael, Puno. En este sentido, la empresa como parte introductoria de sus operaciones, ha propuesto la solución integral, donde la herramienta principal son los índices de gestión por unidades estratégicas de negocio y los índices de gestión por unidad operativa, los mismos que permitirán evaluar el desempeño de su organización frente a sus metas, objetivos y responsabilidades. En este sentido, el establecimiento de este sistema busca crear una cultura en la organización, a través del seguimiento de cada uno de los índices, permitiendo a la alta gerencia y a los demás niveles ejecutivos de la empresa hacer control de gestión, así como una reducción de los costos operativos en el Área de Mina y mejoras en los resultados de voladura.

Sep 12, 2005

By J. Chai

In order to find the behavior of dewatered unconsolidated strata during the process of injecting water through a borehole, a new type of fiber Bragg grating (FBG) sensing system was successfully used for the real-time strain monitoring of unconsolidated strata during a water injection process for a dewatered unconsolidated strata of a coal mine. The unconsolidated strata water injection test was implemented through a borehole at a depth of +115.83 to +135.15m. The employed FBG strain monitoring system and ground water level observation system were installed at the depth in the unconsolidated strata where the water injection was conducted through two different boreholes. The water injection pressures in the test were 0.1, 0.2, 0.3MPa respectively, and the total water injection volume was 4226.84m3. The relationships between the water injection pressures, water injection volume and the strain change of the unconsolidated strata, the stress and strain conditions of the unconsolidated strata before and after water injection, were analyzed. This paper presents the results of these tests, and shows that the dewatering compression of the unconsolidated strata is reduced with increasing water injection pressures and water injection volumes. Comparing the stress-strain conditions before and after water injection, it is found that the stress of the water injection strata is in tension, which confirms the theory that the settlement of the thick unconsolidated strata is directly caused by the reduction of ground water levels. The high sensitivity and stability of the FBG monitoring system used was able to realize the real-time strain monitoring of the water injection process within a deep unconsolidated strata. This FBG monitoring system and the test results presented are very important for understanding further treatment of settlement in unconsolidated strata.

Jan 1, 2012

By Ivo Dreiseitl, Kondratenko. Anatoly

"The second prime area within the Interoceanmetal Joint Organization exploration area named H22 was delineated in 2013 with the goal to ensure sufficient nodule reserves for profitable mining operations and processing.The knowledge base for area H22 has been obtained from archive materials. The geological situation can be characterized as follows: the sea bottom is represented by tectonic blocks oriented in a sub-meridional direction. According to swath mapping, the depressions (troughs) are contoured at depths of 4500-4600 m while the tops of horsts occur at 4300-4350 m. Volcanic relief occupies 6% of the H22 area; in the eastern part a multicone volcano was detected. Its area at the base is 153 km2. The maximum height of a cone above the base is 850 m. The crystalline basement composed by tholeiitic basalts of late Oligocene age is covered by about 100 m of sediments. Semi-consolidated to consolidated calcareous nanofossil sediments of the Marquesas formation are deposited on the basement. Higher up in the profile sediments of the Clipperton formation occur. They are represented by unconsolidated siliceous (Radiolaria, Diatom) ooze. Sediments containing calcium carbonate have not been detected. Where opaline silica (or CaCO3 if any) content is below 5%, the sediments belong to zeolitic clays or red pelagic clays. Grain size composition of the seabed and the near-seabed sediments in H22 classifies them into clayey silts."

Sep 1, 2014