Search Documents

By Robert G. Lundquist

The Bureau of Mines compared longitudinal strain energy output of a percussive drill to energy determined by measuring maximum piston velocity. Strain gages were used to determine the strain-time waveform and its amplitude at seven levels of operating pressure and eight levels of thrust. The longitudinal strain energy was found to be approximately 14 ft lb less than the maximum piston energy at comparable operating conditions.

Jan 1, 1969

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. Considerations in the mine shaft layout, design, sinking, outfitting, testing and commissioning are set forth against the background of requirements of applicable parts of Code of Federal Regulations, Title 30.

Jan 1, 1988

By Thomas H. Wilson

Common offset and refraction seismic data have been collected over four longwall panels at two different locations within West Virginia. Surveys prior, during and after mining were made in both areas. The velocity of seismic wave propagation in the overburden rocks is observed to decrease in response to panel emplacement. Variations in the magnitude of this reduction, apparent as an additional first arrival time delay in the after mining common offset surveys, do not appear to correlate directly to the amount of subsidence that has occurred. Velocity reduction and signal absorption zones are also produced in the cover beyond the panel face over the adjacent unmined areas. Signal absorption and velocity reduction zones have also been observed over room and pillar entry areas between mined panels. Velocity reduction zones have been- observed beyond the panel face in both shallow and deep mines, but the signal absorption zone has not been observed over the deeper mine. Changes in the compressional wave velocities of the cover rocks are associated with changes in their elastic moduli. Differences between borehole derived and surface seismic derived interval velocities, are related to differences in the properties of the bulk volume sampled by each method.

Jan 1, 1988

By Stephen H. E. Phillips

This report outlines the modifications that have been carried out to the original prototype rectangular shaft sinking equipment for its use in a circular shaft. The surface testing of the machine is described where seven, 24 ft. diameter shafts were excavated to an average depth of 21 ft. at rates ranging between 1 ft/hr and 1.9 ft/hr depending upon the prevailing conditions. The durability and productivity standards for the equipment were established indicating that the objectives of the project had been realized. That is, when using the machine the sinking rates could be increased by 25% and costs reduced by a corresponding amount compared with conventional drill and blast methods. In addition it was shown that the machine had been developed to a state of fitness for sustained underground use.

Jan 1, 1981

By P. K. Hofmeyr

Base Metal (Cu, Ni, Mo, Zn, Co etc.) analysis traditionally has been very slow in conventional analytical laboratories which can lead to additional costs being incurred in waiting time of drill rigs or mining excessively off-reef. Recent developments in the automation of analytical laboratories now allow for very rapid turn-around times for base metal analytical data which can help reduce such costs as well as reduce the unit costs of the analyses themselves. 2.0 CONVENTIONAL ANALYTICAL LABORATORY PRACTICE Conventional analytical laboratories are necessarily are very manual. Sample preparation is slow and laborious, samples are moved from stage to stage manually and, typically, all samples are processed in batches so a sample which is the first to be, say, milled has to wait for the complete milling of the batch before it advances to the next stage eg. mixed with wax prior to pelletising for XRF analysis. Inevitably this results in long sample data turn-around times for laboratories handling large numbers of samples. Manual sample preparation can only be accelerated by increasing staff which increases costs and can lead to additional errors being introduced. Cleaning of sample preparation equipment, eg. crushers and mills, between samples is essential to avoid cross-contamination between samples and this is slow and labour-intensive. In manual sample preparation the correct sample numbers staying with the samples is totally dependent on the efficiency of laboratory operators. It is extremely difficult to detect when errors have occurred due to the switching of sample numbers during the sample preparation stages. Running duplicates and QC samples at best is only partially successful in detecting when sample number switching errors have occurred. Errors of this nature and cross-contamination problems due to incomplete cleaning of sample preparation equipment tend to occur when laboratories are working at pressure due to high sample numbers and when supervisors are not present during 24/7 laboratory operations which is often required on plant process control laboratories. These problems are common to all conventional analytical laboratories and their magnitude is dependent on the level of control and efficiency of QC systems practised by individual laboratories. The disadvantages of conventional manual analytical laboratories can be summarized as follows:- 1. Labour-intensive which is costly especially when multiple shifts have to be used during 24/7 operations.

Jan 1, 2005

By E. K. Stanek

The field tests involved ten coal mines in which transients were initiated on the dc system from which the parameters of the dc mine electrical power system could be determined. The data processing involved the use of a Fourier Analyzer to filter noise and fit an exponential curve to the field waveforms. From this data analysis it was possible to find the dc system resistance, inductance and time constant. The survey of nationally recognized laboratories was conducted to establish that the recommended test criteria were practical. The development of test criteria for dc fuses used in mines was based on the measurement of parameters in the field, the survey of testing laboratories, literature searches, laboratory test, etc. A computer program was written to analytically predict the parameters measured in the field. This approach has limitations but reasonable agreement with field results was obtained. A brief laboratory testing program was carried out to verify the practicality of the recommended criteria and establish the accuracy of the conclusions concerning dc fuse performance.

Jan 1, 1984

By d&apos, Kathleen J. Amico

This summary appears in Minerals Year-book volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1966

By Hanns J. Billmayer

Optimized Operator Compartment layouts based on previous Bureau of Mines activities in standardization and optimization of controls were designed and installed in three operating vehicles. Two National Mine Service 48A-36 TorKars were modified in production prior to delivery to the Quarto Mining Company. An Elkhorn AR-4 scoop owned by Adanac Coal Company was modified in a local rebuild shop. The modified vehicles were then evaluated underground under normal production conditions for a 60 day period. Vehicle operators and management appear well satisfied with the compartment modifications.

Jan 1, 1976

By Steven Putt

Seismic While Drilling (SWD) is a newly developed technology in the mining industry. Improving upon Measurement While Drilling (MWD) systems, SWD measures mechanical properties of the rock at incremental depths down a blast hole at a much higher resolution. SWD is also immune to common failures and inconsistencies of MWD such as operator and drill specific variation. Seismic While Drilling records the velocity and elastic modulus of the rock with centimeter accuracy in real-time. These properties measured while drilling blastholes are then used as a proxy for density which can be used for: • High resolution geologic modeling • 3D ore control • Drill and blast optimization • Drill to mill tracking One of the distinct challenges with SWD systems is the sheer volume of information acquired. With thousands of measurements per blasthole, the data can be overwhelming for even an experienced engineer. To overcome this complex challenge, the latest cloud computing and analytics models have been simplifying and organizing the data. These newer technologies can amplify an engineer’s capability by delivering actionable insights into their drilling and blasting workflows. The paper presents new results from Datacloud during recent Seismic While Drilling trials in iron ore, metallurgical coal, and hard rock mines around the world. The measurements are compared with wireline geophysical logs, core data, drill cuttings, and conventional measurement while drilling (MWD) systems to validate the technology and show how the data can be used.

The steps for the beneficiation of iron ores differ from ore to ore, depending on the mineralogical phases of the particular iron ore and the nature of the association of the gangue minerals with iron oxide in that ore. The extent to which the beneficiation can be undertaken economically depends both on the amount and the nature of the gangue. The analysis of the phases present in an orebody optimises the mining and process operations (separation, beneficiation, sintering, etc).X-ray diffraction (XRD) provides qualitative and quantitative information about the main ore phases as well as the gangue mineralogy and the amorphous content present in a sample. In addition, modern quantification methods such as Rietveld refinement allow the calculation of the distribution of elements in solid solutions such the substitution of Fe with Al in goethite or hematite.The use of high speed detectors has made XRD an important tool for grade and process control. Finger printing of XRD data can facilitate multi-dimensional mapping of ore deposits and drill cores, identifying regions of favourable mineral compositions. Grade control using XRD can be completely automated and controlled remotely.The two case studies in this paper demonstrate how XRD and finger printing can be used for grade control, process optimisation and quality control of a goethitic and a magnetitic iron ore. The enormous potential of XRD as an inexpensive, reliable tool, useful in the characterisation of iron ores will be demonstrated.CITATION:K÷nig, U, 2013. Application of x-ray diffraction to iron ores - potential implications for grade control and downstream processing, in Proceedings Iron Ore 2013 , pp 275-280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Yotamu Stephen Rainford Hara, Animesh Jha

The investigation focuses on a low temperature recovery of Cu and Co from a 40 wt% SiO2-(30 wt%Fe,6 wt%Al)2O3-10wt% CaO-7wt%CuO-7wt%CoO slag over a temperature range of 1173K to 1323K. The alloy phases containing Cu-Co and Fe-Co alloy formed via the carbothermic reduction of oxides: MO + C = M + CO(g), where M represents metallic copper, cobalt or iron. In the direct reduction of oxides, the recovery of metallic phase was well below 90% at 1323K, due to the kinetic barrier which was analysed and attributed to oxygen and metal-ion transport in the slag. This barrier was overcome by adding CaSO4 and carbon, which yields a matte (MS) phase via MO + CaSO4 + 4C = MS + CaO + 4CO reaction. Lime thus produced in situ participates in metal oxide/metal sulphide reduction reactions, which are analysed with the help of X-ray powder diffraction, scanning electron microscopy, and thermogravimetric analysis.

Jan 1, 2014

By Tom Treleaven

The widening of the Panama Canal to approximately 130 feet (40 m) for its entire length began just a few years ago. The original expansion program was slated for completion in 18 to 20 years, but has recently been reduced for completion within the next four years. This means that a tremendous amount of blasting at simultaneous points along the canal, by both the Panama Canal Commission (PCC) and many subcontractors, is necessary to achieve the new completion deadline. The accelerated program also imposed many logistical concerns, since marine trafIic is always heavy and cannot be stopped for blasting. Because some of the large and heavy cargo vessels clear the bottom of the canal by only about 6 feet ( 2 m), the blasting cannot result in any large boulders into the center of the canal, for fear of grounding and damaging a vessel, not to mention the traffic delays and lost income of approximately 1 to 2 million dollars per day.

Jan 1, 1997

By G. D. Schena, C Chiaruttini

The feasibility is demonstrated of reconstructing the volumetric distribution of liberated particles and middlings by use of a damped, weighted least-square regularisation method. This allows a precise mass balance to be obtained around a separation/concentration unit, permitting evaluation of the partition curve (Tromp curve) of the separator. Areal grade measurements are made on polished sections of feed, concentrate and tailings and a kernel-based inversion technique is then used to obtain the volumetric grade distribution of the three assemblages. A plain kernel (number of occurrences) and a weighted kernel (each occurrence counted with its area) are used for the solution. Testing of the method on computer-generated synthetic areal grade measurements indicates that it offers a valid alternative to the tedious conventional procedure of conducting experiments with heavy liquids

Jun 21, 1905

By G. C. Lammers

The object of this study was to determine the economic feasibility of hydraulically transporting Sandow (Tex.) lignite 100 miles and dewatering and thermally drying the transported lignite to a surface-dry condition. The most important factors involved in the feasibility of hydraulic transport, are the degradation incurred during transit, the length of the line, and the cost of alternative methods of shipment. In pipeline tests in which roughly 75 miles of hydraulic transport was simulated the percentage of minus-325-mesh solids increased from about 1 to 41 percent for both lignite and bituminous coal; in the micron sizes the coal fared considerably better than the lignite. Such degradation, even though it enhances flow through the pipe-line, severely aggravates the dewatering problem on lignite. Cost studies indicated that continuous vacuum filters offer the most economical means of dewatering minus-1/8-inch material. Surface moisture, if high, must be removed by relatively expensive thermal drying.

Jan 1, 1958

Thank you for this opportunity to address your conference on 'The role of coal in the New Zealand energy market'. New Zealand's energy market has, in common with much of New Zealand, undergone major change following the market reforms of the Labour Government. As far as the energy sector is concerned this change has been for the better, as it has created for the first time in a very long time a 'true economic market' for energy in New Zealand. This is in marked contrast to the previous regime where: ò Electricity was state operated, subsidised and cross subsidised. ò Oil was imported and subject to a raft of taxes and duties. ò Coal produced by state mines was priced by cabinet committee, based on other energy prices rather than on the costs of production and delivery of the energy product. Today, with the establishment of the SOE's we have a market of competitive supply, where the customer has the choice of energy with prices based on the true costs of production and delivery. This can only be good for the customer as the cost is now based on the real costs of production, not on political whim. So where does coal fit in this brave new world of free market energy supplies? Well, opportunity, they say, knocks but once.

Jan 1, 1990

By H. Soto, J. Jara, F. Nava

"A combination of oxidation and precipitation was used to eliminate cyanide from gold milling effluents. Preliminary laboratory work developed with both synthetic cyanide solutions and with industrial effluents indicated that ozone can easily destroy free cyanide and weakly complexed cyanide (i.e. copper and zinc cyanide). In this case the reaction is quite fast and seems to be controlled by the mass transfer of ozone to the solution. Experimental results indicate that free cyanide and weak-acid dissociable cyanide in mill effluents can be reduced to less than 1 ppm. However, the iron-cyanide complexes proved to be quite resilient to destruction with ozone and they remained in the solution even after most of the free and weakly complexed cyanide was destroyed with ozone. These results were confirmed in a pilot trial developed at the Sphinx plant in northern Quebec.To deal with the problem presented by the presence of the iron complexes two different approaches were studied: use of a combination ozone-ultraviolet light oxidation, and the precipitation of iron-ferrocyanide complexes in the residual solution after ozonation. This last method proved quite promising since reduced the total cyanide levels of industrial solutions assaying as much as 250 ppm to less than 1 ppm of total cyanide. Control of the · pH of the solution was the key to obtain the precipitation of the iron complexes. The use of iron to precipitate cyanide complexes has the advantage of being less expensive and less toxic than copper (used by the Inco process)."

Jan 1, 1992

Upgrading of a Flow Sheet Selection PC Algorithm for Refractory Concentrates Treatment

Sep 13, 2010

By Glenn Adkins

This report characterizes pivoting joints in the structures of mining machinery and how the wear on the various components, i.e., pins, lugs, yokes and bushings, may affect the safety of mine personnel where these components are allowed to wear excessively before repair or replacement.

Jan 1, 1979

By Paul J. Lewis

Estimation of the axial side shear resistance of drilled shaft rock sockets is directly related to the unconfined compressive strength of the bedrock. Commonly, the mean unconfined compressive strength value is calculated from a range of laboratory test results and is used to estimate the side shear of the bedrock. This paper presents the results from a full scale axial load test performed on an 8.5-feet-diameter drilled shaft rock socket, and compares measured side shear values to estimated values for two different rock strata. Measured side shear values correlated well with the design value calculated for the "strong" rock stratum, but did not correlate well with the design value calculated for the "weak" rock stratum. The mean unconfined compressive strength was used to calculate the side shear in both strata, but review of the laboratory data indicates that this value may not have been appropriate for the weak stratum due to a large variation in the laboratory test results. Also included in this paper is a discussion of the subsurface conditions, the laboratory test results, and the methodology used to design the drilled shaft rock sockets for axial and lateral resistance.

Jan 1, 2005

By K Ehrig, J Griffith

An extensive suite of elements are routinely assayed on all resource drill core samples to assist in deposit scale resource definition, local mine scale delineation of ore zones, and ore characterisation for the planning and scheduling of mining and processing of ores at Olympic Dam. This paper discusses a deposit scale geochemical relation that can be used by mine geologists to find more high-grade ore at the local mine area scale at Olympic Dam.A 3D grade shell representing 0.8 per cent Cu was created for a mine area using drill hole assay data. This defined the geometry of the ore zone. The Cu-grade shell was then overlain onto the existing resource block model to evaluate the relationships between the Cu-grade shell, copper and other elements. The strongest correlation was between copper and manganese. The block model showed a dramatic decrease in the concentration of manganese just below the below the Cu-grade shell.Several drill holes that intersected the Cu-grade shell were selected to evaluate the copper manganese relation at the drill hole scale. As expected, the individual drill holes displayed a strong inverse relation between copper and manganese. A geochemical footwall was then modelled representing 0.1 wt per cent Mn. Using both the Cu– and Mn-grade shells, several drill holes were designed/drilled and all hit high-grade copper.For the vast majority of the deposit the inverse relation between copper and manganese is valid; however, in areas with intense chlorite alteration (related to amounts of mafic to ultramafic rocks) this relation is not as strong, due to increased manganese in the rock mass. Even though using the copper manganese relation as a drill targeting method was not always as reliable in a few small areas of the deposit, it demonstrates the value of using existing assay data integrated with the resource block model to discover local mine scale geochemical relationships which can be used to more effectively design drill holes to discover high-grade ore at Olympic Dam.CITATION:Griffith, J and Ehrig, K, 2017. Using existing data to improve the delineation of ore at the Olympic Dam Fe-oxide Cu-U-Au-Ag deposit, in Proceedings Tenth International Mining Geology Conference 2017, pp 321–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017