Search Documents

By Edward M. Kawenski

Float dust deposits in return airways in bituminous coal and lignite mines present a special explosion hazard. Research is in progress at the Bureau of Mines experimental coal mine to evaluate the degree of the hazard and to develop measures for preventing dissemination of dust into the ventilating air current. To determine the extent of this hazard prevailing in operating coal mines, 711 dust samples were collected in 50 mines located in the major coal fields of the United States. The mean quantity of coal and the incombustible content of the dust in the samples were determined. The term "float dust" is used to designate particles smaller than 74 microns in diameter (particles passing a No. 200 sieve) which have settled from the air current. Dust usually found in roadways and in working places is coarser than float dust, and is termed "coarse dust" (particles passing a No. 20 sieve). Variations in amount and incombustible content of coarse dust in a midwestern mine were studied previously.

Jan 1, 1963

By T. Bertke

This document assesses the environmental aspects of a preliminary design for processing kaolin clay as the domestic resource for recovery of alumina by a hydrochloric acid leach-HCl gas induced crystallization process. The report covers waste sources, control measures, and potential environmental and health effects applicable to the process technology.

Jan 1, 1980

This chapter presents an overview of fatal and nonfatal injuries reported to MSHA during 1986-1995. Reportable injuries follow the criteria for reporting specified in 30 CFR 50. These criteria are listed in appendix A. The data used for these analyses came from the MSHA accident, injury, and illness data closeout files for the years 1986-1995. The MSHA data are described in appendix A and methods used in data analysis in appendix B. There may be slight discrepancies between the figures presented here and other presentations of MSHA data for the following reasons: (1) injuries to nonemployees have been excluded from analysis; and (2) injuries identified by MSHA after the files were closed out are not included. Within the MSHA data, there are differences in reporting requirements for operators and contractors. Contractors are required to report only those injuries that occur during certain categories of work (described in appendix A). For this reason, data on injuries among employees of operators and contractors in the MSHA database should not be considered directly comparable. As discussed in the "Introduction," the MSHA data on fatal injuries differ from the CFOI data (chapter 1) because of varying definitions used for the mining industry. As compared to the CFOI data, MSHA data exclude injuries that occurred off of mine property and include injuries occurring at mills and processing plants on mine property. Tables 4-1 through 4-9 and figure 4-1 provide comparisons of injury frequencies and rates among the commodities. These comparisons are followed by sections 4A through 4E, which provide more detailed tables and figures for each commodity separately. The method used to calculate injury rates is described in appendix B. Since denominator data for occupations (lob titles) were available for 1986 only, estimates of rates by occupation for the entire 10 year period are based on extrapolation from 1986 data. For this reason, estimates of injury by occupation should be interpreted with caution. Fatal Injuries A total of 1,078 fatal on-the-job injuries were reported to MSHA during the 10-year period 1986- 1995. The average annual fatal injury rate for all commodities combined during this period was 30.9 per 100,000 full-time equivalent workers. Mine operators accounted for 908 (84%) of the fatalities and had an average annual fatal injury rate of 28.2 per 100,000. While mine contractors comprised only 16% (n = 170) of the total number of fatalities, their average annual fatal injury rate was 2.3 times higher than that of mine operators (65.0 per 100,000). Table 4-1 presents the number and rates of fatal injuries by commodity for operators and contractors. Contractors in metal, nonmetal, stone, and sand and gravel are grouped together, since MSHA data on employment were not available for rate calculations for these commodities separately. The highest average annual fatality rate for the period, 66.5 per 100,000, occurred among metal and nonmetallic mineral mining contractors, followed closely by coal contractors (63.1 per 100,000). Among mine operators, the highest average annual fatal injury rate was in coal (38.9 per 100,000); the lowest was in nonmetal (14.3 per 100,000). Table 4-2 shows the average annual fatal injury rate by type of operation for each commodity for mine operators only. Of commodities with underground mines, all except stone had higher fatality rates at underground than at surface operations of these mines. The highest fatality rate for any operation occurred in surface operations at underground stone mines (124.5 fatal injuries per 100,000 workers). Stone had the second highest fatality rate for underground operations at underground mines (77.9 per 100,000). The highest rate for underground operations at underground mines occurred in metal (87.6 per 100,000). Table 4-3 shows the number and rate of fatal injuries by U.S. Bureau of the Census occupational groups (described in appendix D) for the 10 occupation-commodity groups with the highest fatal injury rates. These data should be interpreted with caution because the denominator used in calculating the rates was based on an extrapolation from data for the year 1986 only, as described in appendix B. Extractive occupations are represented in this group for three commodities: coal, metal, and sand and gravel. Construction trades are included for coal, sand and gravel, and nonmetal. The distribution of fatal injuries by commodity and work activity for mine operators is presented in table 4-4. A description of the work activity categories is in appendix C. Overall, the leading work activity at the time of injury was using or operating tools and machinery (26.4%) followed by constructing, repairing, and cleaning (24.0%), vehicular operations (18.8%), and materials handling (12.6%). The distribution varied by commodity. The largest percentage of fatal injuries occurred while operating tools and machinery in both coal and stone; during vehicular operations in metal; and during constructing, repairing, and cleaning activities in nonmetal and sand and gravel. Table 4-5 shows the distribution of fatal injuries by commodity and MSHA accident classification for mine operators. A description of the MSHA accident classifications appears in appendix E. The largest proportion of injuries overall occurred during powered haulage (28.5%). The

Jan 5, 2000

Selective Recovery of Platinum from Cobalt-Rich Crust

Sep 13, 2010

By Archie Richardson

The trona mines in the Green River Basin, commonly known as the "trona patch," present an interesting set of rock mechanics issues stemming from mining in a unique underground environment. Like other minerals occurring in tabular deposits, trona is mined using high-productivity room-and-pillar and longwall methods. However, trona does not behave quite like other evaporites and behaves far differently than coal. In this paper, the following key issues in trona patch rock mechanics are discussed: material properties, in situ stress field, water and gas pressure effects, creep characteristics, pillar behavior, roof span stability, floor stability, underground tailings storage, longwall mining, two-seam mining. and solution mining. Many of the existing trona producers are entering potentially more difficult mining conditions, and much consideration is being given to "new" technologies such as longwall mining and solution mining. In analyzing 20 years of experience with trona patch rock mechanics issues the authors have identified key comparisons and contrasts with conventional tabular deposit rock mechanics that will help illuminate what has been learned as the trona patch enters the 21" century.

Jan 1, 1999

By Fred Leighton

The Bureau of Mines has developed rock noise source location techniques that may be used to obtain precise and practical source locations from micro-seismic field data. These techniques enable one to monitor all or any part of a rock structure and map progressive stress buildup or rock movement. Thus, the microseismic method of determining instability in rock structures is becoming an invaluable engineering tool for the mining or civil engineer engaged in rock excavation and construction.

Jan 1, 1970

By Terry J. Close

From 1981-84, Bureau of Mines personnel examined and evaluated mines and prospects in the highly mineralized 62,400 acre Inyo Mountains U. S. Bureau of Land Management (BLM) Wilderness Study Area (WSA), located east of Lone Pine, CA. The 62,400 acres studied is the part of the 87,145 acre WSA designated as suitable prior to February 28, 1983. The WSA is underlain principally by quartz monzonite and quartz diorite that have intruded sedimentary and volcanic rocks. Three types of mineral deposits are present: 1) gold in fissure veins, 2) silver in fissure and replacement veins, and 3) talc in metasomatic lenses. Of the 84 nines, mills, and prospects examined, 54 are significant: 1) 5 in the intrusive rocks total about 4.4 million tons of inferred marginal gold reserves averaging 0.24 oz gold and 0.74 oz silver/ton; 2) three associated with intrusive-sedimentary rock contact zones total about 280,000 tons of inferred subeconomic silver resources averaging 7 oz silver/ton; 3) 27 gold and silver occurrences in the intrusive and sedimentary rocks total about 1.2 million tons of material in poorly defined bodies too small or low grade to be resources; 4) 15 gold and silver occurrences in the intrusive and sedimentary rocks are too poorly exposed to estimate tonnage and grade; and 5) four talc deposits along intrusive-sedimentary contact zones have inferred marginal reserves totaling about 640,000 tons. The marginal gold reserves at $450/oz might be profitably mined (reserve) at a gold price of about $600/oz and the subeconomic silver resources at a silver price in excess of about $27/oz. The marginal talc reserves might become minable at prices of about $50/ton and $80/ton for unprocessed and processed talc, respectively, after present supply sources are depleted. At most of the 54 significant mines and prospects, additional reserves or resources would likely be disclosed by trenching or drilling. Present in the WSA are 13 gold mills, numerous small pits and cuts, 270 underground workings totaling about 36,000 ft, and 80 mining benches totaling about 11,000 ft. Gold, silver, or talc were produced from most of the workings. A total of 1,561 lode and 18 placer samples were taken.

Jan 1, 1985

By Frank B. Fulkerson

Of the about 60 million pounds of aluminum used in the Pacific Northwest in 1960, 40 million pounds or two-thirds was used by 10 companies. One of these companies made airplanes and missiles; one manufactured roofing, siding, and tubing; three produced truck tractors, truck bodies, or truck trailers; two made architectural metal products; one made irrigation and industrial products; one was a general foundry; and one was a shipyard. These companies contributed to regional growth by developing markets outside the area; some have worldwide sales. Aluminum consumption increased at an average rate of 7 percent annually from 1954 to 1960. Airplane manufacture, formerly preeminent in aluminum use, no longer was in first place in 1960. By industrial group, the leading users were manufacturers of building products, 30 percent; airplanes and missiles, 22 percent; truck tractors, truck bodies, and truck trailers; 17 percent; general foundries, 5 percent; ships and boats, 4 percent; mobile homes, 4 percent; other transportation equipment, 3 percent; and irrigation equipment and all other products, 15 percent.

Jan 1, 1962

By D. Hopkins, D. Türler, R. D. Giauque, W. B. Davis, M. Karaca

In a highly collaborative research and development project with mining and university partners, sensors and data-analysis tools are being developed for rock-mass characterization and real-time measurement of mineral content. Determining mineralogy prior to mucking in an open-pit mine is important for routing the material to the appropriate processing stream. A possible alternative to lab assay of dust and cuttings obtained from drill holes is continuous on-line sampling and real-time x-ray fluorescence (XRF) spectroscopy. Results presented demonstrate that statistical analyses combined with XRF data can be employed to identify minerals and, possibly, different rock types. The objective is to create a detailed three-dimensional mineralogical map in real time that would improve downstream process efficiency.

Jan 1, 2002

By A. W. Khair

Laboratory studies indicate that the specimen size influences the compressive strength of coal significantly. In the past, the diameter/height ratio of coal and rock specimens with different geometry and its influence on failure characteristics was discussed (Khair, 1993; Khair, 1994; Khair and Xu, 1994). In the current attempt, tests are designed and carried out under uniaxial condition in the laboratory to investigate the influence of specimen size. Cubical specimens of coal with edge dimension ranging from 5 cm (2 in.) through 20 cm (8 in.) were prepared according to the standards and tested uniaxially. Results show that compressive strength of coal is dependent on specimen size until certain level and later the change in specimen size would not yield significant change in compressive strength. Cubical specimens were chosen for testing because they are not only in close resemblance to underground pillars, but they are also the most stable shape under loading. The failure characteristics of these specimens were analyzed and their applicability to pillar design aspects in coal mines is studied. A detailed analysis of the physical and mechanical properties of the tested coal seam is also presented.

Jan 1, 1996

By S. J. Rodgers

This report presents the results of in-mine studies to determine the severity of dust sources in conventional mining operations. Three underground coal mines were surveyed using gravimetric samplers and GCA RAM-1 continuous dust monitors. Two additional mines were surveyed using only GCA RAM-1 monitors. Data on dust control methods were acquired during the survey, also. The results indicated that cutting/drilling and loading out were the dustiest operations during a conventional mining cycle. Roof bolting, shot firing and product transport were less severe dust sources.

Jan 1, 1983

By David Schlain

The Bureau of Mines investigated methods for electrodepositing platinum-group metals from molten cyanide baths. The preparation of thick, protective coatings on molybdenum, Inconel, graphite, stainless steel, copper, and other structural metals were studied, as well as the electroforming of platinum and iridium crucibles. Iridium, rhodium, and ruthenium can be electrodeposited under an inert atmosphere, while platinum and palladium require the presence of air. Electrolytes may be prepared by direct-current electrolysis in NaCN or mixtures of NaCN and KCN using anodes of the particular platinum-group metal. When the concentration of metal increases to about 0.3 or 0.4 percent, the deposits become bright, adherent, and coherent. Current densities may be 10 to 25 ma/cm2, and plating rates are often 0.5 mil/hr. Platinum and palladium baths deteriorate because of the oxidation of cyanide to cyanate and carbonate, and the precipitation of metal. Changes in the platinum cyanide bath are relatively slow. The protection against oxidation afforded by the platinum-group metal coatings is evaluated by testing encapsulated specimens in a thermogravimetric balance. Surface pretreatment and the use of undercoats are discussed.

Jan 1, 1977

By Thierry Bernard, J. M. Laboz

2000 HIGH-TECH SEMINAR Blasting Technology, Instrumentation and Explosives Applications

Jan 1, 2000

A unity of viewpoint emerged from the workshop. The concept that transmission is via characteristic modes was a common theme in many of the presentations. Also, the confusion an the meaning of monofilar and bifilar to describe these dominant modes was cleared up. But, there was still a healthy divergence of opinion on what constitutes an optimum system. It was generally agreed that further analytical and experimental work is definitely needed. In particular, it was stressed that independent measurements of the constitutive properties of the electromagnetic environment are needed. Also, there was considerable concern that laboratory measurements of rock samples could lead to misleading results for the effective conductivities. Also, there was a general recognition that over simplified propagation theory should not be used to interpret field data. From a theoratical and practical point of view, it was realized that mode coupling plays a vital role in the transmission channel. One must not only understand which and how many propagation modes are excited by the transmitting antenna, but the conversion of energy from one mode type to another must be accounted for. This conversion can either be done intentionally (by fixed mode convertors) or non intentionally (by random wall roughness). In fact, mode conversion can be quite complicated when various propagation paths exist such as when insulated cables, leaky feeders, grounded rails, coal seams, etc. all convey portions of the electromagnetic energy. However, this state of affairs should be regared as an. opportunity for extended communication coverage in mines rather than a limitation of a desig. procedure based on preconceived notions of the dominant propagation mechanism.

Jan 1, 1978

By A. Singh

The control of flotation plants is by no means trivial. Flotation is one of the most interactive minerals? processing operations. The interactive nature of flotation circuits results in oscillations of levels and hence of grades and recoveries. Also, poor level setpoint tracking and disturbances have negative influences on grades and recoveries. The result is an unstable plant with limited scope for optimization. An advanced controller, FloatStarTM, has been developed to provide tight control and to reduce the amount of disturbances in flotation levels. It has been shown on a number of plants that the system results in faster and better setpoint tracking, better regulatory control and faster settling times after start-ups and disturbances. The successful stabilization provided by FloatStar has made it easier to investigate the area of optimization on flotation circuits. Mintek has identified the need for a more meaningful set of setpoints or aeration rates to use as a basis for control than levels and have advocated flow control by looking after residence times. When the feed conditions change, the ideal solution would be an algorithm or strategy that finds the new optimum conditions rather than just having an unguided hunt from the previous point. A multivariable flow-optimizing algorithm, a new module in FloatStar, has been developed to calculate optimum level setpoints and/or aeration rates that will aim to optimize the residence times, mass pulls and circulating loads within a flotation circuit. Keywords: flotation, regulatory, FloatStar, start-up, disturbance, residence times, circulating loads

Jan 1, 2003

By Gerald E. H. Verbeek

As the number of driven concrete piles with Embedded Data Collectors increases, it has become possible to compare the widely used Beta Method to assess pile damage (using the change of pile impedance) with the so-called Measured Pile Integrity (MPI) method (a combination of two approaches using both the change of pile impedance and the change in pile pre-stress levels). After a brief introduction of both methods, this paper presents the outcome of that comparison based on data from more than 400 concrete piles driven in Florida, which brings into question the reliability of any damage assessment method based solely on the change of pile impedance (such as the Beta Method), especially to detect damage near the pile toe. Moreover the paper demonstrates the need to re-assess the damage classification used for the Beta Method as well as the use of Pile Driving Analysis (PDA) to detect pile toe damage.

Jan 1, 2011

A physical modelling study has been carried out to simulate the slag-metal dispersion induced by a high-strength bottom gas injection. Water and kerosene were utilized to simulate metal and slag respectively. A water model of CLU (Creusot-Loire Uddeholm)vessel was used with three different nozzle orientations, namely, off-centre, triangular off-centre and centre. The gas flow rates changed from 0.00599 m3/s to 0.01081 m3/s. Height of heavy and light phases was kept fixed at 0.23 m and 0.02 m respectively. The dispersed phase hold-up was determined at various axial and radial distances, gas flow rates, and tuyere configurations. The observations revealed that at a fixed gas injection rate, as the vertical distance increased in the centerline, straight off-centre orientation resulted in greater dispersed phase hold-up values than those of the centre configuration and the triangular off-centre orientation. The dispersed phase hold-up was found to increase with gas injection rate and decreased with axial distance. The variation of the dispersed phase hold-up with the dimensionless axial distance and the gas injection rate was correlated by using the modified Froude number. The experimental values of the dispersed phase hold-up were found to be in reasonable agreement with the correlated values obtained from the modelling equations. The findings of the present study may be utilized in the ferroalloy refining vessels in terms of designing tuyere locations for optimum processing conditions.

Jan 1, 2004

By Donald J. Ninteman

This Bureau of Mines publication is a literature study of the problem of spontaneous oxidation and combustion of sulfides in underground mines. It summarizes the present-day hazards, process mechanisms, and prevention and control techniques of this growing problem in underground mines. The iron sulfides generally have the greatest tendency to oxidize, particularly pyrrhotite. The presence of moisture and oxygen is essential for the oxidation reaction. Highly fractured sulfides, when found with timber or combustible refuse in slowly circulating air, pose the most serious fire hazard. Quenching with water is effective in quickly dealing with local hot spots, but ventilation at high flaw rates is the most effective and economical means for long-term prevention and control.

Jan 1, 1978

By Stephanie Price

Engineering Associations ?Regulatory authority ?License individuals and firms ?Discipline licensed members ?Enforce against improper acts ?Programs for EIT?s, competence, etc

Oct 1, 2010

By R. D. Dukimo, M. V. Sevian

The nature of fracture and factors that control the extent of fracture in the tumble-drum and drop-tower tests have been identified. The product-size distribution, on which the standard strength indices for these tests are based, and the breakage rate constants depend on a number of factors other than the strength of the lumps. The standard indices and rate constants are meaningful only in a comparative context and for events whose loading mechanism is similar. The results of experiments on three Australian ores, from Yandi, Koolan and Mount Whaleback, are used in combination with fracture mechanics theory to explain why different tumble-drum standards have been found to be fully consistent. A more meaningful measure of strength could be the parameters of the Weibull function, scatter and average strength

Jun 19, 1905