Search Documents

By William J. Campbell

Three types of X-ray analytical instrumentation were compared for applications in the secondary brass and bronze industry. The instruments were a conventional X-ray spectrograph, a portable X-ray spectrograph, and a radioiso-topic X-ray analyzer using balanced filters. The following two general applications were considered: Rapid identification for sorting scrap metals and quantitative analyses to provide guidance in the melting and casting of alloys. Twenty-three analyzed copper-base alloys were used as standards. Although the alloys varied widely in composition, matrix correction procedures were not necessary except for copper. The conventional X-ray spectrograph provides positive identification of the alloys and quantitative values for the six elements investigated--aluminum, copper, iron, lead, tin, and zinc. Equivalent results were obtained with the portable X-ray spectrograph for those elements whose characteristic X-rays are in the wavelength range of the instrument. The radioisotopic X-ray analyzer distinguishes certain groups of alloys and provides quantitative determinations for copper, lead, tin, and zinc. The sensitivity of the analyzer was marginal for the determination of small concentrations of elements of atomic number 26 or lower.

Jan 1, 1972

By J. S. Hansen

To improve mine safety, the Bureau of Mines has conducted a search for better materials and systems to anchor roof bolts. This report describes a study on the ability of a gypsum-based anchoring medium to withstand short- and long-term loads. Results showed that 2-ft-long bolts anchored with gypsum that was injected as plaster slurry at a 0.370 water-cement ratio and cured for 10 min sustained pull test loads equal to the ultimate strength of the bolt steel (about 37,000 lb). For comparison, the minimum required capacity is 17,600 lb. Long-term loads of 15,500 lb were sustained with estimated 10-yr movement of less than 1/2 in. Two-foot-long bolts anchored with gypsum installed in a cartridge in which the water was contained in tiny capsules sustained a pull test load of about 30,300 lb at a 0.319 water-cement ratio and 10-min cure time. At a 0.288 water-cement ratio, load capacity was about 37,000 lb. The lower load capacities of cartridge-installed bolts resulted primarily from the remnants of the water-wax capsules. Above 10,000 lb, creep movement of cartridge-grouted bolts appears excessive, but longer bolts may be capable of resisting creep better.

Jan 1, 1985

By K. E. Gray, M. S. Seth

In Part I of this work,1 equations of elasticity were formulated for transversely isotropic, axisymmetric, homogeneous, porous media exhibiting pore fluid pressure. Equations of elasticity and the thermal analogy method were used to determine transient horizontal, tangential, and vertical stresses and radial displacement in a semi-infinite cylindrical region when either a constant rate of pressure or a constant rate of flow is maintained at the wellbore. In this paper, the approach presented earlier is extended to finite reservoirs for the cases of (1) steady-state flow, (2) constant pressures at the well bore and outer boundary and (3) constant pressure at the wellbore and no flow at the outer boundary. Results of this work show that radial and tangential stress gradients are high near the wellbore but diminish rapidt; away from the well; the vertical stress gradient behaves in the same way but is less severe. Radial stresses are compressive or neutral, whereas tangential and vertical stresses may be tensile, neutral or com-pressive, depending upon the boundary conditions, the physical Properties of the system and the radial distance involved (vertical stresses are always compressive in an unbounded system1. For constant boundary pressures, both radial and tangential stresses increase with time whereas they both decrease for a closed outer boundary and constant pressure at the wellbore. The vertical stress decreases with time for both systems. For steady-state systems, radial displacement may be positive or negative, depending upon the dimensions of the system, the pressure differential and the porosity. Radial displacement may be positive or negative for a closed outer boundary but is positive for constant pressures at both boundaries. INTRODUCTION The importance, utility and complexity of a realistic appraisal of the stress state at and local to a wellbore were indicated in Part I. In this paper the analytical approach presented earlier is extended to finite, cylindrical reservoir geometry for the cases of (1) steady-state flow, (2) constant pressures at wellbore and outer boundary and (3) constant pressure at the wellbore and no flow at the outer boundary. Other than the outer boundary of the reservoir being finite, the physical system and assumptions pertinent thereto are the same as before. The reader may wish to review the mathematical development through Eq. 49 of Part I before proceeding here. SOLUTION FOR GENERAL BOUNDARY CONDITIONS THERMAL STRESSES AND DISPLACEMENTS Since normal stresses do not exist at the free boundaries of a system subjected to thermal stresses, the boundary conditions are

Jan 1, 1969

By G. F. Butterworth

The metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to, produce in the stock a physical condition having the requisite properties. The fist group consists of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat treated by giving it a quench and a draw. These barrels will be referred to as " heat-treated " barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent, of manganese, show a single very pronounced point between 1300" and 1350" F. (704" and 732" C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure shown in Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under a low magnification appears almost homogeneous, as in the case of fine grains of pepper and salt well mixed together, Fig. 6. This structure is substantially the same for all

Jan 1, 1920

By Zhuo Chen, Jun Zhou, Jiemin Zhou

Samples of the reacting suspension particles were taken from the reaction shaft of a commercial flash furnace at different heights. The processes of matte and slag formation and morphology of the samples in the shaft were observed and analyzed. Variations of matte and slag composition in the shaft were investigated. By analyzing the samples taken from the settler at different locations, settler processes were studied such as slag formation, agglomeration and separation of matte-slag phases, Fe3O4 reduction, copper-in-slag reduction etc. In accordance with the characteristic of matte and slag formation the flash furnace can be divided into 6 functional regions, and a mechanism model called as “Micro bath process” is proposed for matte and slag formation in a commercial flash furnace. INTRODUCTION During flash smelting, concentrate particles scattered in the reaction shaft complete their oxidation reactions in suspension. The droplets produced fall into the settler beneath with a small amount of un-melted solid particles, agglomerate and separate into matte and slag layers which are tapped out from their tap holes separately. With respect to the extent of slagging reaction in the reaction shaft, there isn’t any commonly accepted understanding in literature (Kimura, Ojima, Mori & Ishii, 1986; Kemori & Kondo et al.,1988; Kemori, Denholm & Kurokawa, 1989; Fagerlund &Jalkanen, 2000). Some assume that the slagging reaction in the shaft can be ignored and some propose that all slag is produced in the shaft. With regards to the characteristics of the physical-chemical changes of concentrate particle in the reaction shaft, although there are some research results reported from pilot scale and commercial scale experiments (Kemori, Ojima & Kondo, 1988; Hagni, Vierrether & Sohn, 1988; Jorgensen, Taylor, Dickinson & Stevenson, 1992; Swinbourne, Simak & Yazawa, 2002; Kivinen & Tuominen, 2005), they are generally limited themselves to theoretical analysis and calculations. No studies are published concerned with the processes of matte and slag generation in the shaft, quantitative analysis of the processes, variations of matte and slag composition and morphologies of the melts along the axis of the shaft, etc.

Jan 1, 2019

By John C. Holtz

Interest in the possibility of using Diesel6/ engines for haulage power in mining and tunneling is increasing in the United States, owning largely to the reported successful use of Diesel locomotives in European coal mines and to the comparatively recent development of automotive Diesel engines in this country. The extent of this interest has been evidenced to the Bureau of Mines by numerous requests for information as to the factors that must be considered if Diesel engines are to be used safely underground.

Jan 1, 1940

By Kenneth H. Johnston

This publication describes a thermal-recovery project and two waterflood projects in Carter, Garvin, and Stephens Counties, Okla., that will be visited during the 1966 annual tour by the Bureau of Mines in cooperation with the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects arc (1) the movement of heavy (15° to 28° API gravity) crude oil through the reservoir and into the well bore with energy furnished by burning a portion of the crude oil therein; (2) the use of an inverted nine-spot pattern with dually completed injection wells, to produce oil from deep (8,200 to 10,200 feet) reservoirs; and (3) the flooding of five sand lenses separately by using controlled water injections through multizone completed injection wells. Discussion of the individual projects includes information on their early history, method of completing and operating wells, source and treatment of injection fluids, oil production decline curves, and the results obtained from the development.

Jan 1, 1966

By Henry A. Signore

The Appalachian coalfield, located in eastern Kentucky, Pennsylvania, Virginia and West Virginia, has been one of the most productive in the United States. Total production from the Appalachian coalfield during 1994 was 340.8 Mt (375.4 million st), or 37% of the 929 Mt (1 billion st) produced in the United States that year. This region contains various coal types from high- to mid-sulfur coal in Pennsylvania and northern West Virginia to low-sulfur, compliance steam coal and premium-grade metallurgical coal in eastern Kentucky, Virginia and southern West Virginia. The region's product is in high demand in domestic and export markets. Productivity continues to improve, resulting in the primary coal operators solidifying their market positions.

Jan 1, 1995

By Robert W. Smith

[In a certain application it was necessary to compute the incomplete beta function, ß(1/2, p, q), for a certain set of values of p and q. Since the set of p and q values was much more finely spaced than those in any published tables, the authors have decided to make their results available in this report. In connection with this application, the function ß(1/2, p, q) was needed at various points in the p, q plane at intervals of 0.05, 0.05 p = 2q < 10.00. Fletcher, Miller, and Rosenhead3/ state that the only tables available in the desired range are those of Pearson.4/ However, the interval used by Pearson was not small enough for the present application. For this reason, it was decided to calculate the function ß(1/2, p, q) for p = q = 0.05 (0.05) 10.00. This table is published because of the fundamental importance in mathematical analysis of the incomplete beta function.]

Jan 1, 1953

By Daryl E. Radcliffe, Raymond M. Stateham

The Bureau of Mines, under a Cooperative Agreement with the Bear Coal Company, Somerset, Colorado, conducted a large scale evaluation of the effect of time lapse on roof stability. Time lapse in this study is the interval between exposure and permanent support of the mine roof. The study indicates that time lapse is not a critical factor in roof stability provided permanent support is installed before catastrophic failure begins. Concurrently with the time lapse study, investigations were made of stress distribution around resin-grouted bolts, the regional stress field, and anomalous geologic conditions. The behavior of the resin-grouted bolts, at least in the Bear mine, appears to fit the Coulomb-Navier Theory. Geologic conditions are primary factors in trends of roof stability that extend across the mine.

Jan 1, 1982

By J. W. Watkins

This report describes in detail methods of making corrosion tests and chemical analyses that have been used extensively and satisfactorily in a study of plants in which various surface, waters and brines are conditioned and used for water flooding, brine disposal, and reservoir-pressure maintenance in Kansas, Oklahoma, and North Texas. The tests and analyses described were designed and adapted for use in the field in determining the relative corrosive and plugging tendencies of waters from various sources conditioned by different methods. Although the described methods were developed and used in testing oil-field waters in the Midcontinent oil-producing area of the United States, these same methods should be equally applicable to testing oil-field or highly mineralized waters throughout the world. Many of the methods used have been discussed by the writer (1)2/ previously, and some of them have been used for similar work in other laboratories. Early in the development of the practice of the subsurface injection of brines for disposal and increasing the recovery of oil, it became evident that different methods of chemical treatment and conditioning equipment would have to be devised to sustain desired injection rates into water-input wells. These changes became necessary because the highly mineralized waters produced with petroleum from deep formations became chemically unstable when pumped to the surface, owing to loss of dissolved gases as pressure and temperature dropped to atmospheric and to the contact with atmospheric oxygen at the surface.

Jan 1, 1954

By Tatiana Ravani von Ow, Leandro Bomvisinho

"The size of mills driven by ring-gear or by a gearless solution has significantly increased in the last years. This has created additional challenges for the driven equipment. The requirements for the mechanical devices and the power grid have become more demanding. Controlled soft starting and operation, especially in dual pinion mills, as well as the protection of the equipment has gained importance. The selection of the drive solution for the mill therefore becomes more critical. Besides the classical criteria such as performance, efficiency and capital costs other factors come in the evaluation of the system such as flexibility and optimization of operation, reliability and the ageing of the grinding equipment.Variable speed solutions offer significant advantages over conventional fixed speed drives due to their application specific features and process optimization capabilities, even for ball mills where these are not seen yet as a must.The initial capital costs are higher than some of the direct on-line solutions however the benefits for the operation during the lifetime of the mill generated by the use of converter solutions justify the additional higher investment.INTRODUCTIONThe method of powering mills such as AG, SAG and Ball has a long and technically interesting history. It can be said; almost every decade in the last half century had its own trend. The trend was dominated by the market demand, by the process development and requirement of the mechanical and the electrical technology but mostly by the price of the applied technology.All has started about 50 years ago with mill diameters less than 20 feet driven by fix speed synchronous or wound rotor motors with the power of about 2 MW. Around 10 years later, the mill sizes increased, but the necessary torque could not be transmitted by one pinion therefore dual pinion solutions were developed to power the mills. However, realization of the dual pinion solution was only possible when load could be evenly shared between the two pinions."

Jan 1, 2010

By Walter W. Fisher

A study of copper cementation on iron was initiated to determine the effect that deposited copper has upon subsequent cementation. A microscopic investigation of cementation on an iron surface showed that cupric ion precipitates predominately on a growing copper deposit attached to the iron surface. A kinetic study of the cementation process in a revolving drum showed that the cementation rate is enhanced by the copper deposit attached to the iron surface and by the discrete copper particles of a cement copper slurry. The kinetic study also indicated that the character of the deposit is affected by the major anion in the solution. The cementation process is visualized to occur as a series of electrochemical cells in which cupric ion precipitates on copper dendrites attached to the iron surface.

Jan 1, 1973

By C Jia, J Graindorge, L M. Olssen

Picking up abandoned mining tenements and looking to recover remnant resources around old operations is an opportunity that comes with its own challenges and risks. Reliance on information released to government departments (such as the Department of Mines and Petroleum (DMP) in Western Australia) by the previous owners, can compound the risk.This paper explores Alto Metals Ltd’s Lord Nelson and Lord Henry deposits and surrounds near the town of Sandstone in Western Australia. The Lord Nelson and Lord Henry open pits produced around 2 Mt of ore for over 250 koz of gold during production between 1999 and 2010. There has been no further work carried out in the area between 2010 and 2016. The deposits are open at depth and along strike.Alto Metals picked up the tenements in 2016 and has subsequently re-estimated remnant resources around Lord Nelson and Lord Henry, and publicly reported updated Mineral Resources in accordance with the JORC Code 2012.All of the information was manually compiled from data released to the DMP and annual reports. This paper highlights the challenges and risks arising from this data compilation, geological interpretation, re-estimation and classification process, together with future opportunities and challenges for further developing the area.CITATION:Olssen, L M, Graindorge, J and Jia, C, 2017. Starting from scratch – defining remnant resources from publicly available data: a case study from the Lord Nelson and Lord Henry gold deposits, in Proceedings Tenth International Mining Geology Conference 2017, pp 175–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Kenneth H. Johnston

This publication describes a thermal-recovery project and two waterflood projects in Carter, Garvin, and Stephens Counties, Okla., that will be visited during the 1966 annual tour by the Bureau of Mines in cooperation with the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects arc (1) the movement of heavy (15° to 28° API gravity) crude oil through the reservoir and into the well bore with energy furnished by burning a portion of the crude oil therein; (2) the use of an inverted nine-spot pattern with dually completed injection wells, to produce oil from deep (8,200 to 10,200 feet) reservoirs; and (3) the flooding of five sand lenses separately by using controlled water injections through multizone completed injection wells. Discussion of the individual projects includes information on their early history, method of completing and operating wells, source and treatment of injection fluids, oil production decline curves, and the results obtained from the development.

Jan 1, 1966

By J. Koster

In the western United States occurs deposits of low-grade chromite which, when concentrated, may be reduced to ferrochromiun in electric furnaces that derive energy from dams and hydro plants now in course of construction. Montana ore was chosen for the experiments. A 1-ton sample contained 26 percent Cr203, 17 percent Fed, and 17 percent SiO2, plus other constituents, and the concentrates therefrom assayed 44 -percent Cr203, 23 percent FeO, and 0,79 per cent SiO2, Gravity concentration was found to be the best method. Ferrochromiums are of two grades - high-carbon with 66 to 70 percent chromium and 4-112 to 6 percent carbon and low-carbor with 67 to 72 percent chromium and 0.6 to 2 percent carbon. Both are made in electric furnaces that use anthracite as a reducer and suit-able fluxes. The concentrates mentioned mere smelted under different conditions, and it was concluded that domestic ore could be reduced with anthracite to produce a ferrochromium of S to 10 percent carbon content at yields of 90 percent without re-treating the slag. This carbon may be lowered to required proportion with calcium and silicon, but the former requires a great excess and the latter leaves an alloy high in silicon. INTRODUCTION Chromite occurs in several regions of the United States, but the known deposits of this mineral have not been large enough or high grade enough to permit them to compete under normal conditions with imported ores. There are numerous deposits of chrome ore along the West coast. These are generally conceded to be relatively small, although some were worked during the World War. There are some indications of a revival of interest in California chromites. Montana contains large chromite deposits in Stillwater and Sweetgrass Counties. The utilization of chromite for ferrochromium and. the manufacture of stainless steels is distinctly an electrometallurgical problem; consequently, a study of methods for treatment of chromite might pave the way for the establishment of new electrometallurgical industries in the Western States. This thought is supported by the cheap power that is soon to become available from the western dams, Farther, submarginal domestic chrome deposits might thus be turned into profitable producers.

Jan 1, 1936

By J. Koster

In the western United States occurs deposits of low-grade chromite which, when concentrated, may be reduced to ferrochromiun in electric furnaces that derive energy from dams and hydro plants now in course of construction. Montana ore was chosen for the experiments. A 1-ton sample contained 26 percent Cr203, 17 percent Fed, and 17 percent SiO2, plus other constituents, and the concentrates therefrom assayed 44 -percent Cr203, 23 percent FeO, and 0.79 per cent SiO2, Gravity concentration was found to be the best method. Ferrochromiums are of two grades - high-carbon with 66 to 70 percent chromium and 4-112 to 6 percent carbon and low-carbor with 67 to 72 percent chromium and 0.6 to 2 percent carbon. Both are made in electric furnaces that use anthracite as a reducer and suit-able fluxes. The concentrates mentioned mere smelted under different conditions, and it was concluded that domestic ore could be reduced with anthracite to produce a ferrochromium of S to 10 percent carbon content at yields of 90 percent without retreating the slag. This carbon may be lowered to required proportion with calcium and silicon, but the former requires a great excess and the latter leaves an alloy high in silicon. INTRODUCTION Chromite occurs in several regions of the United States, but the known deposits of this mineral have not been large enough or high grade enough to permit them to compete under normal conditions with imported ores. There are numerous deposits of chrome ore along the West coast. These are generally conceded to be relatively small, although some -were worked during the World War. There are some indications of a revival of interest in California chromites. Montana contains large chromite deposits in Stillwater and Sweetgrass Counties. The utilization of chromite for ferrochromium and. the manufacture of stainless steels is distinctly an electrometallurgical problem; consequently, a study of methods for treatment of chromite might pave the way for the establishment of new electrometallurgical industries in the Western States. This thought is supported by the cheap power that is soon to become available from the western dams. Farther, submarginal domestic chrome deposits might thus be turned into profitable producers.

Jan 1, 1936

By Shosei Serata

The Stress Control Method improves productivity and safety in underground coal mining. The method stabilizes the roofs and floors of mine openings in both shallow and deep coal beds, regardless of whether or not there are ground stability problems. This paper describes the means by which a tapered pillar experiment is used to collect in situ data, which is then used as input for a computer model. The resulting computer model is then used to optimize Stress Control design for the mine under study. The behavior of any underground coal mine is not elastic, as is generally conceived in the conventional view of rock mechanics, but rather is highly time-dependent and site-specific. Unfortunately, conventional rock mechanics methods based on the elastic principle are not able to capture the highly non-elastic nature of ground behavior which actually occurs. To capture actual behavior, a new method of study is required. In this regard, geomechanical study of an underground coal mine may be compared to studying the behavior of a living fish. Its true behavior zannot be understood by examining it "dead in the laboratory. It Is the "live" nature of the coal mine that is required for design optimization of the Stress Control Method in the given mine. The Stress Control Method is based on a time-dependent theory of the global behavior of the mine ground, which generally contradicts the conventional elastic theory of ground behavior. Therefore, site-specific adaptation of the Stress Control Method required a comprehensive understanding of the global behavior of the mine as a function of time and site-specific ground conditions.

Jan 1, 1986

By Patrick E. Durnal, Henrik Dahl

"A joint venture of Ben C. Gerwick Inc., Sverdrup (now Jacobs) and DMJM (now DMJM + Harris) designed the $779 million seismic upgrade of the Richmond - San Rafael Bridge over the San Pablo Bay in the San Francisco Bay Area and provided construction support to Caltrans. Construction of the marine foundation retrofi t was completed by a joint venture of Tudor Saliba/Tidewater/Koch-Skanska and their subcontractors: Pomeroy Precast Construction, AGRA Foundations, Dutra Construction and Vortex Divers. Construction management and inspection was performed by Caltrans with the support of various consultants. MARINE FOUNDATION RETROFIT SCOPEThe retrofi t design of the submerged foundations included:??A total of 476 tension and compression micro piles (290- 1140 kips or 1290-5071 kN) installed through cored holes through the underwater bells at 31 pier locations??Fourteen 126/150/164 inch (3.20/3.81/4.17m) diameter CISS (Cast-in-steel shell) concrete shear piles (1160- 2660 kips or 5160-11832 kN) installed through new precast concrete pile cap extensions??Twelve CIDH (Cast-in-drilled-hole) shear piles (1060- 2130 kips or 4715-9475 kN) with 150 inch (3.91m) diameter steel shells to top of bedrock and 30 ft (9,14m) long and 11 ft (3.35m) diameter rock socket installed through new precast concrete pile cap extensions The specifi ed post bid test boring revealed deeper bedrock at one pier location allowing deletion of the rock socket. Thus 15 CISS and 11 CIDH shear piles were installed at 11 pier locations - 9 piers with 2 piles and 2 piers with 4 piles. Cut off elevations for the shear piles ranged from 46 ft to 60 ft (14.0m to 18.3m) below mean sea level and cut off for the micro piles was 8 ft to 46 ft (2.44m to 14.0m) below mean sea level. Almost all foundation retrofi ts required work under limited headroom conditions. Underwater construction connections required innovative design details and construction techniques for each pile type. The 11 piers had 22 precast concrete pile cap extensions installed in pairs and connected by either tremie concrete closure pours or by large pipe struts. The precast pile cap extensions were strapped underwater using large steel bands wrapping around the belled piers with grouted annulus. The precast pile caps were founded with 14 inch (355mm) diameter steel pipe piles, which were either support piles or seismic tension and compression piles. The seismic piles were connected in grouted corrugated steel pipe sleeves cast into the new concrete pile caps."

Jan 1, 2007

By Lennart Mukka

The Kiruna Mine in Sweden currently has three ventilation systems. The first two (a new and old system) serve the production areas. The third system is used for the facilities on the former main haulage level 775. That area includes offices and workshops for load haul dumpers (LHD) and drill rigs. The third ventilation system also covers the crushing and haulage on level 1045. At the present time, the total airflow for the mine is 1,600 m3/sec(3.4 million cfm). The current system serves the levels above the 775 level. The new one is for the levels between 775 and 1,085 m (2,540 and 3,560 ft), which are needed for the new ore body. When all of the production is below level 775, the old ventilation system will be closed down.

Jan 1, 2002