Search Documents

By H. Forster, F. H. Koenemann, U. Knittel

The greenstone belt developed along the Sandawana line, an anastomosing, transcrustal shear zone. The lode gold is concentrated in veins and along brittle-ductile shear zones and other faults. Gold contents of 200 rock samples were found to be well below economically significant levels, excluding purely syngenetic deposit formation. Average gold content of unmineralised banded iron formation decreases from 7.3 ppb in the east (Manica) to 1.6 ppb in the west (Odzi), where depletion reflects hydrothermal leaching. The mineralising fluids may have been generated during deep crustal deformation, metamorphism and magmatism. Gold was hydrothermally deposited during carbonatisation and sericitisation of ultramafic and mafic rocks and during hydrothermal overprinting of banded iron formation and felsic rocks. It is present in native form and as microscopic to submicroscopic inclusions in pyrite, arsenopyrite and pyrrhotite. Argentiferous galena and other sulphides are commonly observed. Rezende, which produced over 38 t Au, is hosted by a granodiorite stock. By-product gold was produced from Cu-Ni sulphides at Mundonguara. The deposits are related to the older, but not the younger, of the granitoids intruding the belt's supracrustal sequences; the estimated age of mineralisation is 2700-2600 Ma. Odzi district, with 61 mines, has produced only 3.5 t Au as its higher-level host rocks have apparently been eroded. Mutare (formerly Umtali) district, with 133 mines and 9 placers, has produced 68 t Au (65 t from Rezende and adjacent deposits), and Manica district, with 23 mines and 8 placers, 12 t Au. Estimated reserves for the Rezende area are 20 t Au and for Manica district 4 t lode Au and 19 t placer Au

Apr 1, 1996

By Youze Xu

The effect of oxalic acid, acetic acid, citric acid and EDTA on extraction of Cr (?) in soils contaminated by chromium- containing slag was investigated using a batch of incubation experiment. The results show that the pH value decreases more obvious with the increase of the amount of organic acid. The amount of Cr (?) extracted increases with increasing the amount of organic acid. When the ratio of organic acids to total Cr was 5:1, citric acid revealed the highest extraction effectiveness, followed by EDTA, oxalic acid and acetic acid, respectively. The amounts of Cr(?) extracted by citric acid, EDTA, oxalic acid and acetic acid increased by 439%, 244%, 215% and 162%.

Jan 1, 2009

By Melford H. Salsbury

The maximum net return from the sale of ores and concentrates of gold, silver, copper, lead, and zinc accrues to the producer when these mine products are marketed to the best advantage. Data are presented that the producer, especially the small mine operator, can use to survey available markets and make a preliminary estimate of the net return to be expected from an ore, on the basis of typical mill, smelter, and freight schedules. A review of the industry is presented by States in which recent production statistics are given, marketing facilities are discussed, and locations of principal mining districts, custom mills, and smelters are shown. Explanations of treatment processes, ore types, treatment charges, payments for metals, and deductions are given. Published rail and truck freight rates for mine products, based on marketing patterns developed over many years, are listed and explained.

Jan 1, 1964

Experimental Mine, Val d'Or, Quebec, Experiments on the ignition of sulphide dust clouds by explosives have been conducted in a 1 m3 explosion chamber. The explosives tested are ANFO, emulsion, aluminized emulsion and Detasheet. By controlling the composition of the ANFO and the emulsion explosive the oxygen balance could be changed in order to identify the dominant factors in the ignition of sulphide dust clouds by explosives. Experimental results, combined with theoretical calculations, show that the temperature of the detonation products is the most important parameter in the ignition of the dust cloud while the combustible detonation products are of secondary importance in the case of non-aluminized mining explosives. In the case of aluminized explosives and explosives having very negative oxygen balance the ignition of the dust cloud is assisted by the large amount of combustible detonation products.

Jan 1, 1993

By Lawrence M. Gochioco

The interpretation of coal seismic data requires a certain precision and accuracy to make the results more reliable. The signature of the seismic wavelet provides a host of valuable geologic information. Subtle features and anomalies, not easily observed in conventional black and white seismic sections, are enhanced through color attribute displays in terms of frequency, amplitude and phase. Coal seam anomalies like sandstone washouts produce a distinct pattern in frequency and amplitude displays due to the change in the net acoustic impedance contrast. Faults produce frequency and amplitude variations due to interference within the Fresnel zone that straddles the fault. The magnitude of displacement is estimated by studying the effects of faults on reflection amplitudes and frequency from computer-generated models.

Jan 1, 1989

By Kurt Oakes, Paul Worsey, Braden Lusk, Tony Brasier, Scott Crabtree, Randy Wheeler

Theoretical description of destructive wave interference and the use of sacrifi cial holes is included and is supported by data collected at Springfi eld Underground. Finally, the process by which the reduction in vibration was achieved in practice is described. Results are discussed for several production blasts taking place over a one year period.

Jan 1, 2008

By R. A. Cummings

Certain roof shales in coal mines deteriorate upon exposure to the atmosphere, causing difficulties in the mining operations and adding to the cost. This report presents the results of both field investigations, in a West Virginia mine, and laboratory studies on the effects of atmospheric moisture on roof shales. Based on these observations, a conceptual procedure is presented on how shale deterioration might be predicted during exploration, and guidelines are given as to how air tempering or conditioning chambers may be designed to reduce moisture effects. Recommendations for further studies are included. An annotated bibliography of the literature constitutes the second volume.

Jan 1, 1981

By Erdal Ünal

The computer program introduced in this paper is based on design guidelines developed for selection of support systems used in mine roadways. The support types considered include rock bolts as well as rigid and yieldable steel arches. Using the computer program, the design engineer can select the type, pattern and specifications of the support systems suitable for various roof conditions. The concepts utilized, assumptions made, support selection criteria and description of the computer program, developed for the PC, are included.

Jan 1, 1989

Validation and Application of Filtration Theory to Plate and Frame Pressure Filtration - From Laboratory to Full Scale

Sep 13, 2010

By E. D. Calvert

The room temperature tensile properties of commercially pure titanium and seven titanium alloys prepared by skull casting were determined in the as-cast and heat-treated conditions. Data were compared with property data from tensile tests on wrought alloys of the same compositions in the as-worked and heat-treated conditions. The alloys evaluated were Ti-5Al-2.5Sn, Ti-6Al-4V, Ti-6Al-4V-lSi, Ti-6A1-2Sn-4Zr-2Mo, Ti-6A1-6V-4Zr-4Mo, Ti-6A1-6V-2Sn, and Ti-11.5Mo-6Zr-4.5Sn. Test specimens were prepared from both static and centrifugal castings and from plate fabricated by forging and rolling vacuum-melted ingots. The data indicate that the alpha and alpha-beta alloys have strength properties in the as-cast condition that are reasonably close to the strength properties of their wrought counterparts in the as-worked condition. An exception to this was the Ti-6A1-6V-4Zr-4Mo alloy for which insufficient data were available to form any firm conclusions. Fine-grained cast structures of Beta III (Ti-11.5Mo-6Zr-4.5Sn) were shown to be generally stronger in the as-cast condition than the wrought alloy in the as-worked condition except for the yield strength of one structure that was unusually low. Heat treatment of this alloy produced properties that were unpredictable. Indications are, however, that optimization of heat treatment parameters for each cast structure could produce strength properties equal to that of wrought materials.

Jan 1, 1974

By Wang Xuguang, Zhang Xiaozhi, Li Guozhong, Xiong Daiyu

The emulsion explosive is a new kind of water-based industrial explosives that was developed at the end of 1960s. In the 1970s, BGRIMM invented EL-series emulsion explosive that created a new era of water-based industrial explosives technology and products in China. From single type to varieties, the perfect BGRIMM emulsion explosives technology has been formed, which consists of 9 series, over 30 types explosives and related production equipments and processes such as cap-sensitive rock emulsion explosive, opencast emulsion explosive, coal permitted emulsion explosives, low-temperature-resistant emulsion explosive, high-temperature-resistant emulsion explosive, high power emulsion explosive, bulk emulsion explosive for loading truck and powder emulsion explosive. From the early 1990s, BGRIMM successfully developed opencast emulsion explosives and the computer controlled continuous production line of small-diameter cap-sensitive emulsion explosive which raised emulsion explosive production technology of our country to a new lever. With the successful development of powder emulsion explosive and related computer controlled continuous production line, on-site mixed emulsion explosive and loading truck as well, the category of industrial explosives is getting more complete and reasonable. This paper pres ents the history, achievement and development of BGRIMM emulsion explosive technology, also forecasts the future of linked technology.

Jan 1, 2003

By Yajie Wang

Traditionally, roof falls are usually attributed to bad roof strata and high vertical stress related to the overburden depth. However, roof falls under shallow overburden depth are oflen caused by a high horizontal stress field. Recent studies have proven that the high horizontal stress field, if existing, plays a major role in roof stability. Also the roof conditions are related to the entry diredions under a horizontal stress field. Questions are: How to orient the entry to a favorable direction to prevent the roof falls? If the entry cannot be oriented, how to support it? Through a case study in mine A, this paper analyzes the horizontal stress effect on roof stability. The guideline for the entry orientation is given based on the results of analysis. Additionally, suggestions are made for those entries that cannot be oriented to a favorable direction.

Jan 1, 1998

Under the Town and Country Planning Act 1977 the Ministry of Works and Development has a responsibility for providing information to local and regional planning authorities on public works and matters of national development and importance, for the exercise of their responsibilities under this Act. One such matter which has recently become a source of concern is the development of South Island lignite. In 1979 the Ministry of' Energy produced a position statement outlining a programme of' research leading to the possible extraction of lignite in Southland or Central Otago for conversion into about 50 per cent of New Zealand's liquid fuel requirements by 1995. Understandably this possibility has caused considerable concern at the local level, expressed particularly by bodies such as Federated Farmers and the local authorities. In the absence of any factual knowledge short of mere conjecture been able to recommend to local authorities is that they limit their planning period to ten years. After this time more information regarding the size, nature, location and certainty of the proposal will permit a more accurate assessment of the implications of the York. While on holiday earlier this year I took the opportunity to visit opencast mining areas in Germany and England to gain an appreciation of the scale of impacts involved and discuss with those concerned the procedures used in planning for such operations. What follows is a brief description of these operations, a comparison with the likely development in this country and the extraction of what may be some relevant principles of' operation for the planning of an environmentally acceptable project. Please note that the views expressed in this paper are mine alone and are not necessarily those of the Ministry of Works and Development.

Jan 1, 1981

By J. R. Cobble

The Federal Bureau of Mines conducted static tests at 2,500° F on 39 refractory compositions, and dynamic tests at [2,825°35° F] on 31 commercial refractory brick specimens to determine their resistance to corrosion and erosion by a slag similar in composition to that used in producing insulating mineral wool. The static tests showed fireclay, low-alumina compositions (<70 percent A1203), zircon, zirconia, SiC, and clay-bonded graphite refractories to be unsuitable. Dynamic test results indicated that magnesia and chromia compositions were superior to high-alumina compositions (=70 percent A1203) as a furnace lining for melting mineral wool. Data from these tests indicated that magnesia and chromia compositions with low RO/R203 mole ratios were more resis tant to attack by mineral wool slags than ones with high RO/R203 mole ratios.

Jan 1, 1975

By Unknown

Blast Site Security Involves: * Clearing the area * Controlling Access * Warning Signals

Jan 1, 2003

By J. E. Davidsen, M. Honstad

"A well-maintained tap-hole channel is important in order to achieve good and stable furnace operation over time. A worn or short tap-hole channel can lead to more violent flow, significantly increasing the fume emissions during tapping and leading to more metal being mixed with and lost to the slag. Over time, a worn tapping channel might cause side channels and damage to the lining around the tap-hole area. This can result in a burn-through which is a considerable safety risk and will cause significant production losses. At Eramet Norway Porsgrunn, tap-hole maintenance has been done regularly with electrode paste for over three decades with good results. This article summarizes some of the experiences obtained from this practice on a 33 MW SiMn furnace, as well as a change to a coal tar pitch-free binder. IntroductionA well-maintained tap-hole channel is important in order to achieve good and stable furnace operation over time. Metal and slag are regularly tapped from the furnace and may cause a lot of wear on the tapping channel, increasing the risk of lining damage and ultimately leading to a burn-through. On furnace 10 at Eramet Norway Porsgrunn, the tap-hole area is the part of the lining that has been by far the most prone to burn-through since the startup of the furnace.Experience shows that almost all lining problems have started with burn-through in the tap-hole area or in close proximity to the tap-hole. During tap-hole repairs, side channels with metal and slag have also been observed emanating from the main tapping channel. In addition, a shorter tapping channel will cause more violent flow. This can lead to more metal droplets being entrained in the slag, and increase the risk of the furnace not being closed properly at the end of the tap.As a burn-through is a considerable safety risk, and also causes significant production losses, systematic work has been performed over the years to maintain the tapping channel in order to prevent burn-through."

Jun 1, 2019

By Minna Karstunen, Patrick Becker

"Abstract The deformation behaviour of a foundation on deep mixed columns in a natural soft soil is a three-dimensional problem, which has to be considered adequately in numerical modelling. However, simplifications are often made due to the computational costs of fully coupled 3D analyses by either modifying geometry of the problem or material parameters in 2D for plain strain analyses or by modelling the problem as 2D axisymmetric case. The volume averaging technique (VAT) is an enhanced 2D FE technique that enables mapping the 3D problem in two-dimensions, yet modelling the two constituents (column and soft soil) with appropriate different constitutive models within a homogenized material. The performance of the volume averaging technique is demonstrated by considering unit cell simulations of floating and end bearing columns in soft soil. The results with VAT are compared and validated against conventional 2D axisymmetric and fully coupled 3D finite element analyses.IntroductionThe properties of very soft clays, silts and organic soils can be improved by stabilizing agents, such as lime and/or cement that are mixed into the soil in situ by using auger-type mixing tools in situ. Deep mixed columns are extensively used to reduce deformations and to improve the overall stability of embankments and foundations on soft soils. Whilst the most typical applications are embankments, increasingly the method is used under foundations. The first category of applications is very common in Scandinavian countries, whilst the latter application has been pioneered in Poland, as an environmentally friendly (low CO2) and cost effective alternative for piling. Due to economic and environmental reasons there is an increasing interest in the technique elsewhere in Europe. With deep mixing, the strength and deformation properties of the soft soil can be improved, and the risk of unwanted deformations is substantially reduced.Numerical methods, such as finite element (FE) analysis, can be used as an alternative to conventional design methods. They are particularly suitable when considering serviceability limit state, i.e. deformation analyses under working loads. FE analyses allow using advanced constitutive models that take account of the complex stress-strain behaviour of natural soil and stabilized columns, respectively. The problems that involve a grid of circular columns under an embankment or a strip footing are fully three-dimensional problems. As 3D analyses are very laborious and expensive, an enhanced 2D technique using the so-called volume averaging technique (VAT) is utilised. The basic idea is to describe the column-improved ground as a homogenized composite material, and using clever mathematics to map the true 3D problem into 2D. Once the constitutive relations of both composites are defined, the response of the column-improved ground can be simulated in 2D subject to arbitrary loading and boundary conditions."

Jan 1, 2014

By J. Geisler

When addressing Germany’s resource supplies, we need to distinguish between those domestically available and imported ones. Resource extraction ostensibly competes with the designation of protection areas. However, the parallel existence of wildlife and plant life, and operations in the areas used for resource extractions is continually underestimated. The European Commission has compiled guidance documents facilitating the extraction of resources from protected areas. With regard to resource productivity, the market appears to be the appropriate instrument for minimising resource consumption. Policy makers are now called upon to create a legal framework leading to a consensus accepted by society.

Jan 1, 2011

By S. R. Gilbert, C. O. Bounds, R. R. Ice

"Many ores are upgraded to produce auriferous sulphide concentrates (principally pyrite) which are not amenable to direct cyanidation. Often these refractory gold-bearing concentrates contain undesirable elements such as arsenic, antimony, etc., which present environmental and/or processing problems. The pretreatment techniques most often considered for processing these concentrates prior to cyanidation include roasting, pressure oxidation, chemical oxidation, pre-aeration, and recently, bacterial oxidation. In this paper, the technical performance and economics of bacterial pre-oxidation vs the classical roasting approach for treating a specific auriferous pyrite concentrate are compared. The results provide flow sheets, preliminary operating and capital cost estimates, and rates of return for the two processes and demonstrate the potential advantages of bacterial pre-oxidation. IntroductionThe increased attention that gold has received in the last ten years has prompted mining companies to look for lower grade orebodies. Many of these low-grade ores do not respond well to conventional direct cyanidation recovery techniques. As free-milling ores decline, gold is sought in refractory environments which, ultimately, drive up the treatment costs.There are a number of reasons for a gold ore to be termed refractory, most of which can be identified by thorough mineralogical examination. The mineralogical occurrence of gold can, to a great extent, impact the method by which the ore is treated and, consequently, the capital and operating costs. Gold in a refractory ore can often occur as discrete particles locked in a host of silicate or carbonate gangue, or associated with sulphides or sulphosalts. Depending on its particle size, gold can be liberated and recovered by mechanical size reduction such as regrinding. This approach is most effective for gold in the 10 - 50 micron range. Gold can also be associated with clay, iron hydroxides, or other minerals which tend to coat the gold surface and inhibit the penetration of the cyanide solution, resulting in poor plant recovery. Because of their resistance to cyanide dissolution, gold tellurides and other refractory gold minerals are also responsible for losses to the tailings. For these reasons, it is paramount that the mineralogical occurrence of the gold be thoroughly and accurately determined before selecting a final process flowsheet."

Jan 1, 1988

By Jackson R. Pressley, Bruce Vandenberg

The knowledge of how and when your explosives go off can help you make intelligent decisions regarding future application of explosives thus removing some of the black magic associated with blasting. The net result will be intelligently set-up shots with timing, explosive charges, and placement more accurately done. Lower operational costs can be achieved when the correct combinations are applied.

Jan 1, 1992