Search Documents

By Robert M. Doerr

The research objective was to determine the effect of vanadium alloy additions on the oxidation behavior of cobalt-nickel Alloys. Eighteen alloys were reacted with 0 2 at 0.5 arm and 1,351°, 1,389°, and 1,429° K. The alloy compositions consisted of Co-Ni master alloys (0, 22, 50, 70, 91, and 100 wt pct Ni) with V additions of 0, 0.9, and 2.7 wt pct. Large early deviations from, or changes in, the parabolic rate constant were encountered, but the reaction rate in most cases declined approximately in accordance with the parabolic rate law. Relatively, the vanadium degraded the oxidation resistance most at the highest nickel contents. In some cases, melting of the oxide was inferred from microscopic evidence and X-ray diffraction measurements disclosed the presence of low-melting vanadates.

Jan 1, 1970

By Y. Boissonnas

INTRODUCTION, The transalpine rail routes in Switzerland are well over one hundred years old. As the established routes no longer meet the demands of the continually increasing volumes of rail traffic between north and south, two new routes through the Alps were planed. The old Gotthard rail line is in fact a mountain railway. The northern and the southern access ramps?with a maximum speed of 80 km/h and a maximum slope of 2.2%?reach the old Gotthard rail tunnel at an elevation of approximately 1,100 m above sea level. This is approximately 900 m higher than the city of Milan. In 1992, the Swiss electorate people voted with an overwhelming majority in favor of the project to build the new base routes through the Alps. The Swiss voted again in 1998 in favor of the financing proposal for the new infrastructure. Swiss Federal Railways together with the BLS Lötschbergbahn were commissioned for the realization and management of the Gotthard and Lötschberg routes. AlpTransit Gotthard Ltd., founded by Swiss Federal Railways, was given the task of managing the design and realization of the Gotthard route until the start of regular service. In the meantime the shorter Lötschberg Base Tunnel was open to traffic in 2007

By R. G. B. Pickering

Resue mining was practiced extensively in the East Rand in the first half of this century. The obvious benefits were that a higher grade of ore was trammed to the surface. The disadvantages were slow rates of face advance and an extremely labour-intensive method of mining. A collaborative effort by personnel from Avgold?s Target Gold Mine and Sandvik Tamrock has resulted in the design of a method of resue mining which can be totally mechanized. The purpose of this paper is to describe the methodology used and the proposed new mechanized resue mining method.

Jan 1, 2000

By P. S. G. Leon

One of the most difficult areas in concession contracts in resource-rich developing countries is achieving an equitable balance between the interests of investors, host states and, increasingly, mine and near mine communities. While some countries in the Andean region have resorted to outright or creeping expropriation of natural resource contracts under the guise of resource nationalism, others such as the Democratic Republic of the Congo (DRC), have claimed international best practice in the review (and setting aside) of important concession contracts.

Jan 1, 2011

By J. R. G. Williamson

The Mining Division of Iscor, an integrated minerals and metals company, has recently completed a feasibility study for the establishment of a new heavy minerals mine and smelter in the Richards Bay area of KwaZulu-Natal, South Africa. The mine will produce a heavy mineral concentrate containing ilmenite, zircon, rutile and leucoxene which will be beneficiated at a central processing complex close to Empangeni. The ilmenite will be smelted to produce high-grade titania slag and pig iron for export. The ancient dune containing the mineral deposit is located some distance inland of the coastal dunes, and the sands contain a high proportion of extremely fine material which must be extracted ahead of the gravity separation process. Of the 56 million tonnes to be mined annually over the ten-year life of the mine approximately 23,4%?a total of 13,1 million tonnes of minus 45 micron residue fines?will have to be disposed of in a containment facility. The origin of the fine material is from the weathering of amphibole minerals. The remaining coarse sands will be returned to the mined area to re-create the original dune configuration. A number of options for the disposal of the residue fines have been examined and specialised laboratory tests undertaken to determine the deposition behaviour of the fines. The final solution involved the use of a ?sub-aerial? technique for deposition of fine material in a disposal facility. The resulting arrangement will adequately meet technical and environmental criteria. Upon closure after 10 years of operation, the surface of the disposal facility will be returned to sugar cane cultivation The paper refers to the various options considered and describes the problems associated with competent disposal of the residue fines and the development details of the final disposal facility.

Jan 1, 1997

By Terry R. Neumann

During 1984, at the request of the U. S. Bureau of Land Management, U.S. Bureau of Mines personnel conducted a mineral survey of the 28,600-acre South Pahroc Range Wilderness Study Area (NV-050-0132). The Wit derness Study Area is located in Lincoln County, NV, about 900 miles north of Las Vegas. Five mineral properties and two mineralized zones were examined during this study; of these, one mineralized zone, two small prospect pits, and part of two claims are within Wilderness Study Area boundaries. Perlite resources were identified in the study area; however, no significant metallic mineral values were noted at any of the sites. The Wilderness Study Area is dominated by a Tertiary volcanic sequence consisting of an interlayered series of tuffs containing thin beds of volcanic pebble gravel, sandstone, and perlite. At the base of the exposed volcanic section, perlite occurs along a 2.4-mile-long zone that parallel s the study area's northeastern boundary. The perlite is suitable for filtration, insulation, and soil conditioning purposes, Because of prohibitive operation and transportation costs, the estimated 6 million tons of perlite occurring inside the South Pahroc Range Wilderness Study Area are classified as an indicated subeconomic resource.

Jan 1, 1986

By Forrest T. Moyer

Frequency rates of injuries per million man-hours of exposure were improved during 1965 slightly to moderately over those of 1964 at metal mines, nonferrous reduction and refining plants, nonmetal mills, stone quarries and mills, sand and gravel operations, and slag operations. However, at metal mills and nonmetal mines the rates of occurrence of work injuries were less favorable. The severity rates of injuries during 1965 were better than in 1964 at metal mines and mills, stone quarries and mills, and slag operations. Conversely, severity rates were worse at nonferrous reduction and refining plants, nonmetal mines and mills, and sand and gravel operations.

Jan 1, 1966

By Steve Massman, Edward Wipf, Gary Beerkircher

"As mine size and tonnage continues to increase, material handling/processing equipment has also increased in size with 400 MT haul trucks, 2000 KW crushers, 12 M SAG/AG mills, 8.5 M ball mills, 3000 M3 flotation cells and 12.5 MW HPGR’s all with planned designs to increase in size further. Related equipment including vibrating screens have also increased in size with screens seeing feed rates of 3000 MTPH. Open circuit SAG Pre-Crush and closed circuit HPGR flowsheets are becoming more common with large screening requirements. Large multi-slope (banana) or horizontal screens are commonly used for these applications, however as the size of these screens has increased, the number and size of the brute force/overhead exciters has increased but with limitations. An example is a SAG discharge screen that will see surges of material from the SAG mill which overload the screen, reducing the screen stroke or throw causing a large reduction in screen efficiency with excessive fines & moisture in the screen oversize feed to the pebble crushing circuit. This paper will present some actual examples of the use of Two-Mass screens as a solution to these overloading problems and the advantages of Two-Mass screens in other high tonnage applications.Brute Force Drive Compared to Two Mass Drive Vibrating ScreensThe standard single mass screen as depicted by figure 1 is generally recognized in the mining industry. It is characterized by the screen body – labeled as the single mass (Mt) that is supported by isolation springs (Kiso). The stroke needed to process material is obtained by incorporating large eccentric wheels and/or drive boxes (Fb) directly mounted to the screen body via a drive tube."

Jan 1, 2017

By Jorge Chira

INGEMMET realizó el proyecto “Estudio de los Recursos Minerales del Perú” con el objetivo de identificar las áreas prospectivas para propiciar actividades de exploración minera por parte de la empresa privada. Entre las funciones ejecutadas está la “Prospección Geoquímica Regional de Sedimentos de Quebrada”, donde se ha recopilado 5,636 muestras de sedimentos de quebrada, las que fueron analizadas por Au y 32 elementos a fin de elaborar posteriormente el Atlas Geoquímico del Perú. En ese sentido, el presente texto señala el uso del software para el tratamiento estadístico de los resultados a través del soporte técnico de la empresa GEOSOFT. Dicho software genera una tecnología confiable así como lo versatilidad para el manejo e interpretación de diversos datos. También se desarrolló el programa OASIS – MONTAJ; módulo CHIMERA con el cual se pueden manejar en forma exacta una gran cantidad de información geoquímica empleando controles de estándares y duplicados.

Aug 25, 2002

By Fulton Flick

THE micrography and macrography of aluminum and its alloys present certain difficulties. Many of the difficulties attendant on the micrography have been removed by methods developed during the past few years, notably those of E. H. Dix, Jr.1 The development of grain size in aluminum and its alloys may be equally troublesome, yet comparatively little detailed attention appears to have been given to it. Satisfactory reagents. are available for the development of such structures in ferrous and most non-ferrous metals, but those applied to aluminum and its alloys, i. e., alcoholic or aqueous solutions of sodium hydroxide or hydrofluoric acid are not entirely satisfactory. Hanson and Archbutt,2 in speaking of these two reagents, state that "These two reagents give fairly satisfactory results, but they sometimes produce badly tarnished surfaces from which the surface deposit is difficult to remove." It has been our experience that neither of these reagents is to be entirely relied on for developing structures suitable for study or photography. This means that when the etch fails to produce satisfactory results the, specimen must be repolished, through the 000-paper at least, and then etched with another reagent. This procedure entails a con¬siderable loss of time, and the final results may not be all that might be desired. However, the reagent to be described, although not a panacea for all etching troubles, has improved results so markedly that it is felt that it is worth offering as a grain-size etch generally applicable to aluminum and aluminum alloys. Czochralski3 in 1915 mentioned the application of a solution of 10 to 20 c. c. concentrated hydrofluoric acid in 100 c.c. absolute alcohol, etching in this reagent being followed by dipping in concentrated hydrochloric-acid solution.

Jan 2, 1925

By K. Galovich, P. Krivokuca

"Quinsam coal mine is located about 25 km west of Campbell River on the east coast of Vancouver Island, British Columbia. Using continuous miners in a fully mechanized retreat room-and-pillar operation, it produces low sulphur, “super compliance” thermal coal for domestic and international markets at a rate of about 2600 t/d. Currently, 65 people work at the site, including some corporate employees.Opened in 1993, the Quinsam mine had a dismal safety record until 1997. Lost time injuries and medical aids were unacceptably high. In 1998, a change in corporate structure brought a change in safety attitudes; a total and unequivocal commitment to safety as job No.1 by corporate and site management. This commitment was clearly spelled out in a new mission statement, circulated to all employees by the new President and CEO, David Slater: “Safety is job No. 1; Production flows from safety; and Think safety at all times.” As well as re-defining workplace safety practices, QCC tightened engineering controls and enforced strict adherence to mine plans.This paper provides a general background to the mining operation, and describes the safety practices that have resulted in an enviable safety record in recent years, reflected by provincial and national recognition."

Jan 1, 2004

By N. Sahay

Improvement in work place environment by conventional methods viz., installation of higher capacity fan, fans in parallel operation or booster fan is a risky proposition in many coal mines in India because of difficult geo-mining condition such as shallow depth, multi seam workings having thin parting and inter connected goaves one above the other. The situation is further worsened if the mines have fire affected sealed off area connected to different ventilation circuits. On many occasions circulation of more air quantity by increasing fan pressure have resulted in initiation of spontaneous heating. To address these problems, authors have made some improvement in conventional Dynamic Balancing of Pressure Technique and worked out few ventilation schemes which are aimed for neutralization of pressure differential across sealed off area at the same time having improvement in ventilation in the mine. The excess pressure differential across sealed off area is mainly caused by introduction of higher capacity fan. Similar situation prevailed in one of the mines of Jharia Coalfield, India. The problem was solved by application of the above technique. In this paper, brief description of the technique, the problem in the mine, results of investigation, computer simulation studies of various schemes and methodology adopted for implementation of the technique in the mine have been discussed in some detail. Keywords: Dynamic Balancing of Pressure Technique, Spontaneous heating, Work place environment.

Jan 1, 2003

By A. Garassino

A pile design was performed for a thermal power station in Egypt and more than 4000 piles were to be driven. Technical economical reasons suggested the choice of driven composite LACOR piles designed for very high specific loads. Some uncertainties on the behaviour of the pile soil system suggested to perform a test on an instrumented pile. Scope of the test was to verify the possibility of developping the required bearing capacity within the range of the allowable pile settlements values and the effect of the pile joint enlargement on that portion of skin friction to be developped by the upper pile section.

Jan 1, 1991

By O. D. Gonzalez

ThIS communication presents the results of a determination of the permeabilities of hydrogen and deuterium in a iron from 360° to 560°C. Recently Heu-mann and primas' have given values of the diffusivity and solubility in a iron of the two isotopes from which the permeability can be calculated. The work reported in the present communication, however, is a direct measurement of the rate of permeation of the isotopes through an identical iron specimen under the same conditions, so that systematic errors can be minimized in the calculation of the ratio of the permeabilities—the value which is usually of main importance in establishing limits for isotopic differences in diffusive processes. Experimentally the procedure used was the usual one: a steady-state flow of gas produced by a pressure difference across an iron membrane was observed as the pressure rise with time in a previously evacuated, calibrated volume connected to the outlet side of the membrane, while a constant pressure of gas was maintained on the opposite inlet side. The membrane was a cylindrical tube 9.38 cm long, 0.730 cm inside diam, 0.187 cm wall thickness, fabricated of 99.95 pct vacuum-melted National Research Corp. iron (less than 0.003 pct C). One end was sealed by a heliarc-welded iron (99.95 pctj lid of 0.147 cm thickness; the other end of the tube was welded to a 304 stainless-steel tube (0.318 cm ID and 0.318 cm wall) which connects to a vacuum system and to the calibrated volume including a dibutylphthalate manometer. The temperature of the iron membrane was maintained constant to ±0.l°C and was measured with an iron-constantan thermocouple which was calibrated against a standard Pt/Pt-Rh thermocouple: the temperature variation along the length of the membrane did not exceed ±0.5°C. Hydrogen was allowed to pass through the membrane assembly for 72 hr at 615°C before permeability measurements were begun. The system was tested at temperature before and after the experiments by a substitution of helium for hydrogen in the inlet side; under these conditions the pressure rise observed in the outlet side was negligible at all times. The gases used for the permeability measurements were 99.95 pct Matheson prepurified H2 and 99.7 pct D2 (0.3 pct HD) from the Isomet Corp. The gases were dried with liquid N2 before use. In Fig. 1 the logarithms of observed flows, jt, for a pressure difference of 73.4 cm Hg are plotted against T-1 Each point in Fig. 1 represents the slope determined by a least-square evaluation of a plot of the pressure in the outlet side of the membrane against time, including at least two separate sets of observations. Each point in the figure has an uncertainty of ±0.6 pct arising from the experimental uncertainty in the pressure and time measurements. The standard deviation of the observed pressures from the straight lines in all cases is less than the experimental precision of the measurements. The observed flow, jt, includes a small but not negligible flow through the stainless-steel connection.

Jan 1, 1968

By B. Moore, Y. J. Zhang

In today’s competitive dimensional stone business environment, use of available technology is critical to achieve and maintain a competitive advantage. Awareness of improvements in diamond cutting technology, operation planning/scheduling, and geotechnical data manipulation/implementation are the keys to success. This paper presents the modern techniques of limestone sawing and quarrying developed and adopted by Indiana Limestone Company, Inc.(ILCI).To fulfill the growing market demands, ILCI’s quarries are committed to deliver planned quantities of all type of stone blocks in a variety of different colors, sizes, and textures. This involves scheduling which quarry ledges should be mined and when in order to minimize unnecessary inventory buildup. Challenges associated with ILCI’s operation are discussed and summarized in the closing of this paper.

Jan 1, 2004

By George A. Savanick

Coal mine roof shales fracture preferentially at slickensided surfaces because of weak or nonexistent adhesion between two slickensided rock surfaces. The purpose of this Bureau of Mines research was to characterize chemically the thin film of smooth, glossy material that makes up the slickenside. This material was analyzed by electron spectroscopy and ion scattering spectrometry while in place on the rock surface and by standard methods of quantitative chemical analysis on concentrate removed from the rock. These analyses showed that the chemistry and mineralogy of the slickensides are similar to that of the adjacent shale.

Jan 1, 1974

By Peter Barker, Terry Jones

"The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully and efficiently process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals.The KCJ is applicable to a broad range of fine mineral recovery duties, with current installations in the mineral sands, tin, tantalum, gold and nickel industries. Other areas of application are being developed with mineral commodities including tungsten, base metals, iron ore, chromite and apatite/feldspar.Information on the principles of operation of the KCJ, typical performance figures in a number of application areas, comparison to centrifugal concentrators, key elements for a successful KCJ operation and recent developments with the KCJ are presented in this paper to demonstrate the capabilities of the KCJ.INTRODUCTIONAfter a number of years of development by inventor Chris Kelsey, the first commercial KCJ unit was installed at the Renison Bell tin mine in Tasmania, Australia, in 1992. The subsequent decade saw the installation of further KCJ units in applications including tin, tantalum and mineral sands.Development and improvement in KCJ hardware continued and culminated in the introduction of the high-capacity Model J1800 KCJ and standard features such as an automatic screen cleaning system. This opened up further markets and resulted in Model J1800 KCJ installations in the gold and nickel industries, as well as further KCJ installations in the mineral sands and tin industries. In recent years, work has continued on application of the KCJ to many other duties in industries including tungsten, base metals, iron ore, chromite, apatite/feldspar, etc."

Jan 1, 2007

By Thomas W. Camm

This study was done to evaluate the costs of various dumping operations at waste and spoil piles. It has been theorized that accidents associated with dumping operations might be reduced by short-dumping rather than edge-dumping, but many operators have been reluctant to use short-dumping because they believe it is not as cost effective as edge-dumping. To evaluate this perception, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health reviewed the costs of various dumping methods at waste and spoil piles. The study found that overall cost differences between the two methods were not significant in most cases. However, while overall cost differences between the two methods appear small, capital costs could be more significant when short-dumping if numerous dump sites are used concurrently. The choice of which method to use should be based on considerations of the safety of dozer and truck operators.

Jan 1, 2000

By David Norval

Ni, Co, Cu and Pt, mattes are common materials that require granulating and milling of the resultant granules for further processing. This route is acceptable if the material is brittle (friable) which is a property associated with the higher sulphur mattes. For lower sulphur levels, where the matte is less amenable to milling, the costs of the milling increases. This paper will compare water granulation with certain dry granulation processes and the downstream processes required for Hydrometallurgy. It will further introduce and expand on atomisation which offers a further safety benefit in the control of the metal flow into the 'wet zone' with the use of a tundish flow control also reducing the conversion from the matte to powder in one fairly straightforward operation.

Jan 1, 2006

By D R. Peacor, J L. Mauk

Dioctahedral clay minerals in the volcanic-hosted Golden Cross epithermal Au deposit, New Zealand, have been investigated by petrography, X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy/analytical electron microscopy (TEM/AEM) to determine the nature of these minerals in a hydrothermal ore deposit. Heterogeneity in the distribution of dioctahedral clays is observed from the hand-specimen scale to the TEM scale, indicating that primary rock textures and fluid pathways (related to rock type, porosity/permeability and fluid/rock ratios), in addition to temperature, are important factors controlling the distribution. As the proportion of illite in mixed-layer illite/smectite (I/S) decreases, TEM observations show decreasing layer stacking order, parallelism of packets, and packet size, and increasing apparent porosity. AEM structural data show a corresponding decrease in AlIV, AlVI, and K+, and an increase in Si, Ca2+, and Fetotal. The observations of this study indicate that local dioctahedral clay mineral reaction progress is controlled mainly by permeability and structure, but that this is superimposed on a predictable, system-wide clay mineral distribution that is controlled by temperature and fluid/rock ratio.

Jan 1, 1999