Search Documents

By Jamal Rostami, Ebrahim Farrokh

Selection of tunneling method, specially the use of shielded machines for application in deep rock tunnels can be heavily impacted by presence of ground convergence and squeezing conditions. Tunnel convergence is a function of ground conditions (i.e., rock mass behavior, groundwater, in-situ stresses), size of the opening, and TBM operational parameters. The case study of Ghomroud water conveyance tunnel project in Central Iran, which is under construction using a double shield TBM, is used to examine the effect of rock parameters on tunnel convergence and hence on the need for over excavation and shield lubrication to avoid problems with the shield getting stuck. Although it is impractical to perform a continuous assessment of rock mass conditions within the shield or in the lined tunnel, results of field observations and subsequent studies show that the amount of the tunnel convergence has direct correlation with the percentage of fines and large rock fragments in the muck and TBM thrust/torque/ROP. These relationships have been examined and will be presented in this paper.

Jan 1, 2007

By Pefer F. Stacey

This paper considers some of the trends in slope design technology that are emerging as we approach the 21st Century. While the ability to design stable slopes has unproved greatly over the past 20 years, trends towards steep short-term slopes for small highgrade orebodies, and very high slopes for mega-pits centered on low grade deposits are starting to indicate limitations in available technology.

Jan 1, 1994

By Frank Sames

Ground vibration levels are generally predicted using equations such as the USBM equation implementing the scaled distance concept and describing geological and blast design parameters in a ground transmission constant.

Jan 1, 1995

By S. Yamashita

Recently in Japan, unexpected degradation (surface subsidence) at old underground quarry sites, such as 'Ohya-Ishi' (pumice tuff) pit field has often been occurred. At these quarry sites, the excavation was started 20 or 30 years ago with mechanical chain cutter and the Room and Pillar method, and stopped 7 or more years ago. Therefore, a reliable method has been required for an estimation of long term mechanical properties of the rock and for an observation of a stability of rock-pillars or structures. In this study, creep tests under uniaxial compressive load were carried out on the 'Ohya-Ishi', with the aim of estimating the long term stability of the rock. From these results, a creep mechanism of the rock was discussed using the failure mechanism hypothesis proposed by Bieniawski and by others. On this basis, critical time to failure was predicted by the relationship between the logarithm of life time and stress ratio of the sustained axial creep load. Additionally, outline of the monitoring system of AE/MS activity in the field, which have set by the Ohya Aria Consolidate Public Corporation and the others to predict or to prevent the degradation of those residual pillars, is to be reported. Key words : Ohya-ishi, Pumice tuff, Mine pillar, Long term stability, Creep, Critical time

Jan 1, 1996

By J. G. Pippenger

The mining industry has been Australia?s major economic driver over the past decade, contributing 8% to Australia?s Gross Domestic Product and 26% of Australian Stock Exchange Market capitalisation. Australia is the world's leading exporter in coal, iron ore, alumina, lead and zinc; and second largest in gold and uranium. While driving the economy, this resource boom has also created a demand for professional and operating talent that has far outstripped the capacity of Australia?s 21 million residents. I moved to Australia some 10 years ago and have not looked back. This unique island continent with its mix of Indigenous and diverse immigrants ? many still proud of their convict ancestry ? has offered life long memories both professionally and personally.

Jan 1, 2011

By Randall S. Marks

Bonneville Dam, completed in 1938, included the smallest and busiest lock on the Columbia and Snake River Navigation System. To expedite barge traffic through this restriction, a new larger lock was designed and contracted by the U.S. Army Corp of Engineers.

Jan 1, 1997

By John H. Weigand, Stephen V. Crum

"VIBRONICS, INC. instrumented and monitored a residential structure for response to,blasting at aMidwestern surface coal operation. The residence was owned by the mining company and was extremely close to the operation. Blasting was conducted within 120 feet (36.5 meters) of the test structure. Up to seventeen (17), four (4)-channel seismographs were used during the monitoring period. The basement walls and floor were monitored. VIBRONICS, INC. also monitored a brick chimney in the basement and attic. Structural responses were then compared to outside vibration measurements taken in the soil near the foundation."

Jan 1, 1998

By G. Gabra

The kinetics of acidified thiourea leaching of pyrite concentrate was investigated at temperature ranging form 20 °C to a 60 °C. The effect of various parameters on the dissolution rates are discussed. The gold extraction was found to be zero and first orders with respect to Fe (111) and thiourea concentration, respectively. The order of the reaction with respect to sulfuric acid was found to be zero. The activation energy was determined from the Arrhenius plot as 2,039 kcal mole -1 (for a freshly prepared acidic solution containing Fe (111) as the oxidant and at 800 rpm stirring speed. This relatively low activation energy value suggests that the gold extraction is controlled by a-physical phenomenon. Under optimum conditions, more than 90% of gold has been dissolved in about 30 min. and 95% in 60 min. Attempt to recover gold from thiourea solution using active carbon is also discussed.

Jan 1, 1984

By A. Lane

The socio economic risks of mining in South Africa have been emerging for some time now, and have been brought into sharp relief by recent events in the platinum sector. The slow pace of social upliftment in the country has lead to widespread social unrest with consequent calls for different forms of resource nationalism. Fundamentally, the key stakeholders are not fully aligned, and are not engaging productively. This poses significant above-the-ground risk to mining companies. Measuring social impact, deploying inclusive solutions and engaging effectively with stakeholders are three ways in which mining companies can mitigate this risk.

Jan 1, 2013

By Åke Krukka, Heribert F. Broicher

"The iron ores of the Kiruna Mine in Sweden are of exceptional quality but for the phosphorus content in certain zones of the orebody. The prevention of mixing ores high in phosphorus with those low in phosphorus has always been of significant economic importance. The ongoing introduction of tele-mining and automatic haulage by LHDs requires new means in the field of quality control underground, as the experienced miner as well as the underground laboratory assistant no longer are involved in the process. As of 1998 LKAB has been testing prototypes of LIF Analysers for non-contact and real-time measurement of the phosphorus content of ore being transported by LHDs from the stopes to the respective ore pass assigned to a certain ore quality. The principles of the analysis of laser-induced fluorescence, the different test phases and results are described and conclusions made. With bulk sorting of ore underground the mining engineer supports the efforts of the metallurgist in the processing plant.INTRODUCTIONThe Kiruna Mine of LKAB, Sweden is the largest underground iron ore mine in the world. In the early nineties LKAB decided to develop the Kiruna orebody further down from the 775m main level to a new main level at 1045m. This development programme was realised while in the mineral processing section and in the pellet plant further capacity was added (Wyllie 1996).In addition to deepening of the mine, which opened up 330 million tonnes of ore, the exploitation of the so-called lake ore was included in the future planning, adding another 1 15 million tonnes of mineable ore. At an annual production of approximately 20 million tonnes of ore the Kiruna Mine today looks at a developed ore reserve sufficient for the next 20 years.All of the competitors’ ores traded in the world market are from open pit operations. LKAB compensates for the obvious disadvantages by continuous efforts to make the best possible use of her high quality magnetite ore deposit. This objective is realised by combined efforts in the pellet plant, the mineral processing plant and the mine. Propriety processes, latest big scale equipment and high tech solutions for automation lead to high quality sales products at a reasonable cost."

Jan 1, 2002

By Hargraves A. J

The paper outlines events at the Collinsville State Coal Mine, Queensland, leading to the practice of full face multiple shotfiring in bord and pillar development places. The 1954 disaster is referred to, and factors involved in simultaneous shotfiring in coal are discussed. Promising preliminary multiple shotfiring tests at the Colliery are described, as well as the resulting routine measures adopted, and the changes involved. The subsequent inducing of two outbursts under safe conditions by remote multiple shotfiring is given as justification for the changes made.INTRODUCTIONFollowing a disastrous instantaneous outburst (1.0.) of coal and gas at the Collinsville State Coal Mine in 1954, the necessity for inducer shotfiring for the control of possible further outbursts was established. However this mine, immediately classified as gassy after the 1954 outburst, is subject to the general restrictions pertaining to gassy mines which at present preclude the use of inducer shotfiring due particularly to the non-existence of a permitted exploder for more than six shots, and further, because permitted multipleexploders are not designed for remote firing through long lengths of cable. This situation was met by arresting or reducing progress in the production places, thereby reducing the danger of outbursts while means were being considered to achieve overall maximum safety.In August 1957 two full faces were successfully blasted in experimental simultaneous rounds. In June 1958 four full faces were blasted, and in October 1958 full face grunching without prior cutting, Le. inducer shotfiring, was introduced in No. 1 Tunnel as a production feature. In March 1960 it...

Jan 1, 1960

By John Popovich

The MICON RokLok binder system including component and consolidation processes and safety and its first aide are described. The implementation procedures and selection of injection parameters are discussed. Finally a case example of recovering a 30-ft. long roof fall in mainline haulage entry is used to illustrate the economic potential of preventive measures by RokLok injection.

Jan 1, 2001

Uranium ore at Sleisbeck, N.T., occurs as lenticular bodies associated with zones of bleached carbonized schists lying between walls of closely folded quartzite. The ore consists mainly of uranium micas with Borne pitchblende.INTRODUCTIONThe Sleisbeck uranium prospect is about 70 miles E. of Pine Creek, and 160 miles S.E. of Darwin (Fig. 1). The prospect consists of a well-defined, E.-W. trending line of hills, about I! miles long. The line is composed of 3 major hills called the Eastern, Central and Western hills, with minor interconnecting hills and outcrops (Fig. 2).

Jan 1, 1955

By Malcolm Ross

Asbestos crystallizes within rock formations undergoing intense deformation characterized by folding, faulting, shearing, and dilation. Some of these conditions have prevailed during formation of the taconite iron ore deposits in the eastern Mesabi Iron Range of Minnesota. This range includes the Peter Mitchell Taconite Mine at Babbitt, Minnesota. The mine pit is over 8 miles long, up to 1 mile wide. Fifty three samples were collected from 30 sites within areas of the pit where faulting, shearing and folding occur and where fibrous minerals might occur. Eight samples from seven collecting sites contain significant amounts of ferroactinolite amphibole that is partially to completely altered to fibrous ferroactinolite. Two samples from two other sites contain ferroactinolite degraded to ropy masses of fibers consisting mostly of ferrian sepiolite as defined by X-ray diffraction and TEM and SEM X-ray spectral analysis. Samples from five other sites contain unaltered amphiboles, however some of these samples also contain a very small number of fiber bundles composed of mixtures of grunerite, ferroactinolite, and ferrian sepiolite. It is proposed that the alteration of the amphiboles was caused by reaction with water-rich acidic fluids that moved through the mine faults and shear zones. The fibrous amphiboles and ferrian sepiolite collected at the Peter Mitchell Mine composes a tiny fraction of one percent of the total rock mass of this taconite deposit; an even a smaller amount of these mineral fragments enter the ambient air during mining and milling. These fibrous minerals thus do not present a significant health hazard to the miners nor to those non-occupationally exposed. No asbestos of any type was found in the mine pit. © 2007 Elsevier Inc. All rights reserved. Keywords: Taconite; Asbestos; Amphibole; Reserve mining; Tailings; Mesabi iron range; Mineral fibers

Jan 1, 2007

By Dana C. Reinke

A job analysis is a written list of the tasks associated with doing a particular job. In drilling, describing the steps associated with adding rod to the drill steel would be an example of a task associated with the job. How to hammer casing or fish a lost drill bit out of a hole would also be job tasks. Develop a written list of job tasks. Ask drillers in your company if the tasks listed are correct and accurately reflect how to perform the job. While each driller may do the job a little differently, some tried?and?true methods are required to perform certain tasks safely and correctly. You may find a separate analysis is needed for different drilling jobs (e.g., a residential well or a monitoring well). Also remember to include the tasks of both the helper and the driller.

Jan 1, 2005

By R. Bruce Patterson

The New Tacoma Narrows Bridge is a classic suspension bridge founded on concrete caissons. Caisson construction was complicated by the proximity of the existing bridge piers, only sixty feet away. High capacity plate anchors were used successfully to moor the new caissons in currents as strong as seven knots during construction.

Jan 1, 2004

"The Dumont deposit is a large (1066 Mt probable reserve) low grade (0.27% nickel), nickel sulphide project located in the Abitibi region 25km west of Amos, Quebec. Royal Nickel Corporation acquired the project in 2007 and has since taken the deposit through pre-feasibility. And updated, revised pre-feasibility was released in July 2012.The disseminated nickel sulphide and alloy mineralization is hosted within the serpentinized dunite subzone of the Dumont Sill; a differentiated, pervasively serpentinized, ultramafic sill of komatitic affinity. Pentlandite, heazlewoodite and awaruite are the dominant nickel-bearing, metallic phases and can be recovered by conventional methods (flotation, mag separation). Non-recoverable nickel is also present within the silicate matrix of the serpentinized dunite and is locked in serpentine (Fe and Mg-rich variants) and minor olivine.A detailed mineralogical program including 1097 QEMSCAN® samples and 4300 electron microprobe points were undertaken to increase the understanding of the nickel deportment in the various recoverable and non-recoverable phases in a spatial context across the deposit. Eighty-three (83) metallurgical tests performed under a standard procedure have linked the mineralogy to metallurgical performance. This has allowed the creation and modelling of geometallurgical domains on a block by block basis to understand the recovery variation and metallurgical performance throughout the deposit. Understanding the spatial variability of Ni deportment in recoverable and non-recoverable phases through mineralogy is the key to understanding metallurgical performance thus, unlocking the value of the Dumont deposit and other large tonnage low grade ultramafic nickel deposits."

Jan 1, 2013

By J. R. Eastwood

"H.D.P.E. Piping in the Mining IndustryThere has been much use· ms.de of high density polyethylene pipe in the mining industry over the past several years. This is not only in new installations but al.so in areas where other piping materials such as wood, transite, concrete and steel have worn out and failed.The uses of H.D.P.E. in the mining industry are as follows:Tailings disposal linesMine water supply linesTailings water return linesHydraulic backfill linesPit drainageCorrosive liquid supply and disposal linesH.D.P.E. pipe has many advantages for both underground and above ground installations. It is tough, flexible, weather resistant and inert which makes the pipe suitable for many installations."

Jan 1, 1975

By M. H. Moys, J. A. Finch, A. R. Laplante

"A detailed review of ball milling circuit control practices in industry has been carried out. Based on fundamental process performance objectives, a standard system for base-level control of most ball mill installations is presented. This system is simple, inexpensive, and provides the major economic benefits available from contemporary automatic control technology.Value Analysis of Grinding OperationsValue analysis (or engineering, or management), originally developed by Lawrence D. Miles of the General Electric Company (1), focuses on the identification of value (product or process worth versus cost) and provides a systematic procedure for its improvement. A recent research and development project involving the application of the principles of value engineering to grinding operations has provided a basic technoeconomic model of grinding processes (2). The functional objectives of the ball milling process and the means to achieve value based grinding circuit control originate from this study.The Need for Grinding Circuit ControlThe economic effectiveness of a process is determined by the quality or value of the product and the related processing costs. If the inputs (both the raw feed and the applied processing work) are absolutely constant, the product characteristics and the process efficiency will be determined only by the engineering design. The need for and degree of process control is therefore determined by the nature of variations or upsets in the process inputs, and the extent to which these effect product value and operating costs."

Jan 1, 1988

Using Positron Emission Particle Tracking (PEPT) to Investigate Industrial Systems

Sep 13, 2010