Search Documents

By Allen Chung, John Twomey, Christopher J. Greet

"It is widely accepted that the type of grinding media has an impact on the grinding chemistry and subsequent flotation behaviour of the sulphide minerals being separated. There are countless laboratory investigations demonstrating that inert grinding media produces more oxidising pulp potentials, reduced levels of grinding media corrosion products and superior concentrate grades and valuable metal recoveries. However, taking these results to industrial scale has proven difficult.Work conducted at the Ernest Henry Mine, in north western Queensland, Australia, at laboratory and pilot plant scale clearly indicated that using a high chrome grinding media resulted in significant improvements in both copper and gold recoveries. However, advancing this work to plant trial represented considerable financial and technical risk to the mine.This paper provides details of the protocol developed and used during the high chrome grinding media plant trial. It describes the test regime employed to measure changes in pulp chemistry, and the statistical methodology utilised to interpret the results. The work also highlighted the need for close cooperation between the metallurgists on site and the researchers conducting the trial.To date, the trial has produced excellent results: indicating that the copper recovery has improved by about 2 percent. The successful application of high chrome grinding media to the Ernest Henry ore has increased metal value by $18.7 million USD per annum based on current spot price for copper.INTRODUCTIONTheoryThe application of electrochemically inert grinding media to mineral systems has been extensively studied (Table 1). Broadly, these studies indicate that most sulphide minerals are more noble than the grinding media used during comminution. Therefore, the sulphide minerals are cathodic with respect to the forged steel grinding media, and the following reactions apply:"

Jan 1, 2011

By C. Pelley, S. Kelebek, G. Kunzel, S. Gregersen, M. Pollanen

A series of small-scale tests was conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the material properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Poisson’s ratio, Pwave, S-wave velocity, point load test index, crushing, and grinding work indices were evaluated for samples without any blasting load and for samples which had received a variety of blast loads ranging from a single impact with a lowstrength detonating cord to a combination of impacts at different times and significant impacts with powder factors close to those used in practical blasts. It was shown that the rock mechanics parameters change even at low impacts, suggesting easier crushing of the rock. Damage values appear to be affected by timing as stress wave superposition affects the damage process. Fragmentation is achieved at higher impact levels while work index modification of the fragments is also observed when high powder factors are used, suggesting improvements in grinding.

Jan 1, 2006

Provide an unobstructive means of measuring small changes in distance from roof to floor or from rib to rib of a mine opening and the rate of closure in order to help operators of under-ground mines detect hazardous ground conditions. Approach A small ultrasonic measurement system was developed to detect g round movement and define closure rates. How the System Works The system contains two parts: a transducer and a readout device. The small ultrasonic transducer, similar to an audio speaker diaphram, is plucked with an ultrasonic frequency every six seconds. This frequency wave is sent through the air and reflected back to the transducer off any surface at which the transducer is pointed. The amount of time needed by the ultrasonic wave to make this round trip is accurately measured using a precise oscillator / timer and is converted into a measure of distance. The accurate 6-second time interval is used to convert any subsequent changes in the reading to a rate of change in feet per minute. Two readings are then displayed alternately on the readout instrument.

Jan 1, 1984

By H. Wyslouzil

"The Kelsey Centrifugal Jig is a gravity separation device which utilizes the principles of the conventional mineral jigs but with the additional feature of being able to vary the apparent gravitational field. This is accomplished by utilizing the specific induced movements of the conventional jig within a centrifuge.Pilot plant trials have been underway since July 1988 to evaluate the potential applicability of this technology to various process streams at Rio Kemptville Tin.The grade/recovery relationships for samples treated in the jig were consistently better than results obtained from tables. Recoveries of more than 90% were attained at concentrating factors ranging up to 20. When compared with electrostatic separators, the jig achieved equivalent metallurgical results in a two stage process, without the expensive requirement of filtration and drying. Recoveries exceeding 96% were achieved with final concentrate grades averaging higher than 60% tin.INTRODUCTIONMineral jigs have been used for hundreds of years. Many different types have been developed, and each one has numerous variations. In recent years, the idea of applying centrifugal forces to conventional jigs has been put to practical tests and today a number of units are in commercial production. In principle, by enhancing the apparent gravitational field, it should be possible to recover finer particles by overcoming viscosity and surface effects which tend to limit existing gravity devices. In addition, it may be possible to use gravity to separate minerals with much smaller specific gravity differences."

Jan 1, 1990

(This paper reviews the reasons for and the principles followed in designing and constructing complete new surface works at the mine of the Zinc Corporation Limited, Broken Hill, New South Wales, and describes the layout, plant, buildings and services.)The Zinc Corporation mine produces high grade lead, silver and zinc sulphide ore. Lead and zinc concentrates are sent by rail to Port Pirie, where the lead is smelted and the zinc concentrate is shipped to Tasmania, England and other overseas countries.Some time ago consideration was given to the advisability of sinking an additional shaft. For some years the old main shaft had been working at full capacity and developments underground had indicated that the mine would eventually be capable of an output greater than that which could be handled through the shaft. It was therefore decided to sink a new main shaft and the site chosen was in footwall country 900 feet south of the old main shaft. The reason for the move south was so that the new shaft would be opposite the centre of gravity of the ore-bodies at depth. The size of the new shaft is 27 ft. ,6 in. x 15 ft., and the work was put in hand early in 1936.It was intended to haul the whole mine output through this shaft, which was 1,600 feet from the mill then operating. An extensive conveyor system thus became necessary unless a new mill was built near the shaft. A careful study of the situation was made by the management and consideration was given to requirements for expansion, the condition of...

Jan 1, 1940

By R. Sankey, L. Gatty, F. Bizzozero, G. F. Shannon, F. Savaglio, L. McDonald

State mining regulations in Queensland stipulate that a mine be provided with an earth installed on surface and that all underground equipment that needs to be earthed should be connected via a copper conductor to this surface grounding point. The regulations further require that all exposed metal surfaces in underground substations be connected to an earth. In a study of earthing conditions at Mount Isa mine it was found that the physical anchoring of metal work at substations (with rockbolts and associated steel mesh) also provides an excellent electrical connection to the country rock. It was established that not only is the mine's earthing system grounded at numerous underground locations but also that such anchor points offer, in general, a path to ground with lower resistance than does the legally required grounding point on the surface. It is recommended that metalliferous mines should utilise a multiple-earth system and not a run earth connected to a single, above-ground earth point

May 1, 1991

By Dan A. Brown

The following paper was written by Dr. Dan A. Brown, P.E. Brown is an Associate Professor at Auburn University's Department of Civil Engineering. The paper was originally presented at a FHWA's Transportation Research Board meeting and is presented here with the author's consent. Construction and design of drilled shaft foundations in hard pinnacle limestone requires flexibility from all parties involved due to the variability of the subsurface conditions. This article describes some strategies which have been found useful in the Birmingham, Alabama area. The importance of well trained and experienced field personnel in these conditions is noted. It is also vital that engineers understand the construction challenges so as to provide both quality assurance and cost effectiveness in design and in the specifications.

Jan 1, 1991

By Bruce Geller

The 2004 Prospectors and Developers Association of Canada (PDAC) conference contained an air of optimism and excitement that has not been seen since 1997. Many segments of the mining industry are alive and well. This is largely a reflection of improved metal prices, themselves due to the strong euro and improvements in Asian economies. Those factors offset higher oil prices, a weaker U.S. dollar and concerns about the Middle East. This report is an overview of the conference. It is supplemented by an examination of conference handouts, abstracts and a few complete papers that are on the PDAC’s Web site www.pdac.ca. Sixty PDAC 2004 abstracts are available at the same site, along with 15 complete papers in PDF format. The conference was held March 7-10 in Toronto, Ontario. It was attended by a record 9,200 delegates from 85 countries. About 8,000 people from 74 countries attended the 2003 conference.

Jan 1, 2004

A rotating disc geometry was used to provide a uniformly accessible surface for a kinetic study of copper cementation with zinc in sulphate solution. For copper concentrations of the order of 10 p.p.m., a porous, adherent deposit is formed on the zinc surface and this has a significant influence on the reaction rate. When the specific mass of deposit is less than about O· 35 mg/cm2 the surface may be considered as smooth and the rate is described by simple convective counter diffusion of zinc and copper ions through a laminar diffusion boundary layer to the deposit-solution interface. In the presence of additional deposit, the diffusional mass transfer rate is increased by increased surface roughness.The rate under these conditions is first order, with the degree of enhancement independent of further increases in the specific deposit mass. The enhancement in rateis, however, directly related to the initial mass flux and the species involved in the reaction.Preliminary work showed the same mechanism to apply to cementation from chloride solution, solutions of high zinc concentration, and cementation of copper with iron..

Jan 1, 1970

Being a geologist I intend describing the renaissance of the gold industry in Australia within its geologic framework; there is a geological pattern to the numerous gold projects which have been brought on stream over the past decade. We are now about midway through our third and largest gold boom which, at a peak of 7.5 million ounces is about twice the production peaks achieved in the preceding booms. From discovery in 1851 through 1870 we saw the first boom largely based on alluvial production in NSW and in Victoria at the great Ballarat and Bendigo Goldfields. The discovery of the Golden Mile in Kalgoorlie, Western Australia, underpinned the second gold boom in the period 1895 - 1915. On that basis the present boom should last through the next decade.   It has been a golden decade for Australian gold production. From less than ten mines in 1980 with production over 10 000 ounces and the largest, Telfer, with output of about 130 000 ounces we now find over 130 deposits being worked around the country today that produce over 10 000 ounces with the largest, Boddington, having an output of over 400 000 ounces. In total these mines produced an estimated 210 tonnes of gold in 1989 and we expect this year, 1990, that a new record production of between 240 and 250 tonnes will be set. This positions Australia in third place in the Western World behind South Africa #1 and the USA #2 and fourth in the world with the Russians holding second place overall behind the South Africans.

Jan 1, 1990

By D Craw, L Cox, R J. Norris

The Rise and Shine Shear Zone is a mineralised low-angle deformation zone traceable for at least 7 km through biotite zone schist of the Dunstan Range, central Otago. The zone is commonly believed to be similar to the actively mined Macraes deposit. The Rise and Shine Shear Zone occurs in the immediate footwall of the Thomsons Gorge Fault, a regional scale Cretaceous normal fault that juxtaposes chlorite zone schist against biotite zone schist. Most mineralised rocks are deformed and record a progression from early stages of semiductile deformation to more brittle cataclasis. Folds in mineralised rocks trend northwards. The mineralised schist is hydrothermally altered with variable silicification, sericitisation, chloritisation, replacement of titanite by rutile and carbonate alteration. Gold is associated with pyrite and arsenopyrite and occurs in both ductile and brittle microstructures. Sheared and mineralised schist is cut by north-striking fault zones which host mineralised quartz veins. Veins in the shear zone contain hydrothermal albite. Trace element analyses show enrichment in As, U, Th and rare earth elements. Many of the above features are similar to Macraes deposit, but there are important differences. In particular, the Macraes deposit is hosted in lower grade rocks and truncated beneath by a normal fault, Macraes has no U or Th enrichment, Macraes veins have no albite and folds at Macraes trend NW-W. Rise and Shine mineralised rocks have no Cr enrichment and no hydrothermal graphite.

Jan 1, 2005

By Samuel Canchaya

Los paquetes medianos y grandes de software a minería contienen en sus módulos de estimación de reservas alguna forma de análisis variográfico geoestadístico. En esa perspectiva, el presente trabajo señala la optimización de métodos tradicionales utilizados en dicha estimación a través de los conceptos y parámetros de la caracterización variográfica y estadística psra así minimizar las limitaciones de los métodos tradicionales.

May 25, 1998

By H. U. Ross

"INTRODUCTION Extensive studies have been carried on pure gold to determine the various factors that affect its dissolution in alkaline cyanide solutions. With the extension of milling to refractory ores more intensive investigations on the effect of impurities in the ore on the dissolution kinetics are needed. The present work describes experiments carried on refractory flotation tailings with the object to determine how the recovery of gold could be increased. The effect of arsenic and antimony in the ore and the excessive use of lime are discussed. Control of cyanide losses is also dealt with.MECHANISM OF THE GOLD DISSOLUTION REACTION In aqueous cyanide solutions, gold is believed to be dissolved by one of the following reactions:4Au + 8NaCN + O2 + 2H20 = 4NaAu (CN)2 + 4NaOH (1)2Au + 4NaCN + 2 + 2H20 = 2NaAu (CN)2 + 2NaOH + H202 (2)2Au + 4NaCN + H202 = 2NaAu (CN)2 + 2NaOH (3) The first of these, known as the Elsner Equation is supported by )4 3,2,1(several authors while others(5,6) support reactions 2 and 3 known as the Bodlander Equations. According to Habashi(7), the overall reaction for the dissolution process is as shown in equation 2. Most of the workers agree that hydrogen peroxide is produced in the course of the reaction."

Jan 1, 1973

By T. Gammatikopoulos, C. Gibson, M. Aghamirian

Lithium is an alkali metal found in brine deposits in the United States, Chile and Argentina, as well as in hard rock deposits in Australia and North America. In hard rock deposits, spodumene (LiAl(Si2O6)) is the major economic lithium bearing mineral. Spodumene is typically upgraded through a combination of dense media separation, flotation and magnetic separation. One of the major spodumene concentrate quality specifications is the iron oxide content because it will help determine if the concentrate is considered ceramic grade for use in ceramics and glass or chemical grade for use in lithium ion batteries. The rejection of iron bearing silicate minerals from artificial ore composites (high amphibole and low amphibole, high quartz/feldspar) from a hard-rock spodumene deposit was investigated using magnetic separation and flotation. The efficacy of Wet High Intensity Magnetic Separation (WHIMS) in iron rejection was found to be dependent on the mineralogy of the iron-bearing silicate minerals including modal distribution, liberation and association. When magnetic separation was conducted prior to flotation, the Fe2O3 grade in the final flotation spodumene concentrate was reduced from ~3% to ~1% Fe2O3 , and improved lithium recovery in flotation was observed. It was determined that it was most effective to conduct WHIMS on the flotation feed after scrubbing and de-sliming because this reduced the required magnetic field to recover iron-bearing minerals, likely because slime coating was greatly reduced. Flotation collector screening of four different collectors with varying rosin acid content demonstrated a potential increase in selective flotation of spodumene over some iron silicate minerals with decreasing rosin acid content in the fatty acid collector. However, due to marginal difference in flotation results with the various collectors tested, further testing is required to confirm the observations made and establish a hypothesis regarding the effect of rosin acid content.

Jan 1, 2017

By Frank Sames

Most Blasting Programs are developed focussing on the environmental impact with respect to blast vibration and airblast. Compliance with existing regulations or policies limiting the immissions are generally achieved through constrains in the blast design, or monitoring programs. Efficient monitoring programs combine compliance monitoring and blast assessment. Signals, which are obtained in the area of direct influence of the seismic source, can contain valuable information about the blast design parameters. Techniques to analyze blast vibration signals have advanced and can assist in understanding the contribution of individual blast parameters to blast vibration and airblast. Advanced signal analysis encompasses magnitude analysis, Fast Fourier Transforms (FFT) and frequency scans in the frequency domain, as well as filtering in the time domain. Through examples, the advanced signal analysis techniques and their limitations are described and discussed, showing the impact of blast timing, timing accuracy, charge configuration and the geology dependent transmission behavior. Optimization criteria and pragmatic monitoring programs can be developed on the basis of the most influential blast parameters. In addition, however, safety and the cost efficiency of the blasting program are essential to the success of an operation. That is where advanced signal analysis techniques can interface with blast planning, computer assisted modeling and information systems. A valuable process can be developed to ensure compliance with existing regulations and efficient risk management for mining operations, while tracking cost and supporting operational decisions. A conceptual blasting information system is presented.

Jan 1, 2000

By David Estrella, Hector M. Lizama, Jhonny Carrión

"Microcel™ sparging systems were installed on one column of the molybdenum cleaner circuit and one column of the copper first cleaner circuit at Antamina. The Microcel™ system is known to generate finer bubbles than jetting-type spargers, and smaller bubbles have been associated with higher recoveries in flotation. Alternating tests were carried out on the molybdenum column, using either jetting-type spargers or the Microcel™ system. Experimental conditions of gas flow rate, wash water rate, and froth depth were tested. Use of Microcel™ decreased the bubble sizes from 2.6-2.9 mm to 1.5-2.0 mm. In addition, Microcel™ improved both unit molybdenum recovery and unit molybdenum concentrate grade. In the copper first cleaner circuit, side by side tests were carried out that compared the Microcel™ column with a parallel columns fitted with jetting-type spargers. Best results were obtained at manifold pressures of 260-290 kPa, where bubble sizes of 1.6-2.6 mm were observed. In either copper or molybdenum flotation, the Microcel™ system required only 50-60% of the gas flow used by jetting-type spargers.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and has a nominal 100,000 t/d mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone [Evans et al, 2005]. Ore body thickness is 100 to 150 m and has the shape of a flat-lying crescent. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper, zinc, and lead-bismuth concentrates are transported by pipeline down to the port of Huarmey. Molybdenum concentrates are bagged and trucked to port."

Jan 1, 2008

By D. J. de Beer

South Africa had a late start with rapid prototyping (RP), with the first system being available in 1991. Up to 1994 only three systems were available in SA. Through active research participation from the CSIR and a number of universities, supported by technology transfer programmes and industry awareness workshops, adoption of RP technologies started to grow. Internationally, RP grew to the extent that several country-based member organizations were formed, and an initiation meeting of the Global Alliance of RP Associations (GARPA) took place during the SME Rapid Conference in Dearborn, USA in 1998. South Africa (SA) was invited under the auspices of the Time Compression Technologies Centre (TCTC) launched by the CSIR, and received an invitation to become a member of GARPA through the launch of a national, inclusive organization. The latter gave rise to a RAPDASA planning/launch meeting held at the University of Stellenbosch, which culminated in the first RAPDASA international conference held in November 2000 at the CSIR, and the election of a first RAPDASA management committee, also at the 1st AGM held during the conference. RAPDASA has been a pillar of strength since then, with an annual international conference being presented. As South Africa?s RP awareness grew through the RAPDASA and independent activities, so did the availability of RP platforms in SA.SA also became a benchmark for other countries/late adopters to follow, as slowly a position of following became a position of leading through innovative applications. The paper highlights SA?s development approach and history, together with the discussion of case studies in various fields. Contribution to the light metals industry will also be discussed. Keywords Rapid prototyping, additive manufacturing, product design, rapid tooling, rapid manufacturing, medical product development.

Jan 1, 2011

By Jon C. Volkwein

In This Chapter [Instruments for measuring dust How to calculate the amount of dust from a source How to get a valid concentration measurement Sampling to assess control technology effectiveness] When there is more than one source of dust, sampling may be required to find which dust sources are most significant. Then, efforts to reduce dust can be concentrated where they will have the most impact. This chapter explains how to perform dust source sampling. It describes two kinds of instruments that are available and discusses their limitations. It explains how environmental variables such as concentration gradients, dust dilution, and production changes can impact dust measurements. It also suggests practical ways to improve the validity of dust source measurements under adverse conditions, such as high-velocity airflow or the presence of water mist in the air. [Dust source sampling at coal mine longwalls and at tunnels is more complicated. Chapters 3 and 7 have more information on sampling in those circumstances.] TWO KINDS OF INSTRUMENTS FOR MEASURING DUST Gravimetric samplers. The conventional gravimetric sampler is a good device for measuring dust because it is the instrument used for compliance measurements. This dust sampler consists of an air pump, a small cyclone that separates out the respirable size fraction of the dust cloud, and a filter to collect the respirable dust. In coal mines, the Mine Safety and Health Administration (MSHA)-approved gravimetric sampler uses a 10-mm Dorr-Oliver cyclone operating at an airflow of 2.0 L/min [30 CFR78 74 (2002)]. A correction factor of 1.38 is applied to make the results consistent with the U.K. MRE sampler, the instrument on which the 2.0 mg/m3 coal dust standard is based.

Jan 6, 2003

By M. Yavuz

Underground mining method selection (UMMS) is one of the most important issues in mining engineering. Underground mining method should be primarily selected to make use of underground resources optimally. It is nearly impossible to change the mining method once selected by the reasons of rising costs and mining losses. Because of these reasons, UMMS process is extremely important in mine designs and economics. The strategy of underground mining method selection has been studied by different researchers in the literature. Boshkov and Wright (1973) proposed a classification system; Morrison (1976) suggested a selection chart; Laubscher (1981) proposed a selection methodology; Nicholas (1981) presented a classification system; Hartman (1987) developed a selection chart and Miller-Tait et al. (1995) modified the Nicholas? system and developed the UBC mining method selection process. In reality, UMMS is one of the important Multiple Attribute Decision Making (MADM) problems and mining engineers have always some difficulties in making the right decision in the multiple criteria environment. To make a right decision on UMMS, all known criteria related to the mining method selection should be analyzed and the problem solved according to suitable decision making techniques. A review of the literature reveals that decision making techniques have been used for UMMS applications. Kesimal and Bascetin (2002), Bitarafan and Ataei (2004), Bascetin et al. (2006), Alpay and Yavuz (2007), Karadogan et al. (2008) and Samimi Namin et al. (2008) used decision making techniques in UMMS applications. In this paper, two different MADM methods: Analytic Hierarchy Process (AHP) and Fuzzy Multiple Attribute Decision Making (FMADM) are applied to select the optimal underground mining method for a chromite mine and final solutions are then compared. THE AHP METHODOLOGY The AHP method developed by Saaty gives an opportunity to represent the interaction of multiple factors in complex unstructured situations (Triantaphyllou, 2000). The method is based on the pair-wise comparison of components with respect to attributes and alternatives. A pair-wise comparison matrix n×n is constructed, where n is the number of elements to be compared. The method is applied for the hierarchy problem structuring. The problem is divided in to three levels: problem statement, object identification to solve the problem and selection of evaluation criteria for each object. After the hierarchy structuring, the pair-wise comparison matrix is constructed for each level where a nominal discrete scale from 1 to 9 is used for the evaluation as shown in Table 1 (Saaty, 1980; Saaty, 2000). The next step is to find the relative priorities of criteria or alternatives implied by this comparison. The relative priorities are worked out using the theory of eigenvector. For example, if the pair comparison matrix is A, then, [Amax=××- [1] ] To calculate the eigenvalue ??max? and eigenvector w=(w1, w2,..., wn), weights can be estimated as relative priorities of criteria or alternatives. [ ] Since the comparison is based on the subjective evaluation, a consistency ratio is required to ensure the selection accuracy. The Consistency Index (CI) of the comparison matrix is computed as follows: [CImax--= [2] ] where ?max is maximal or principal eigenvalue, and n is the matrix size. The consistency Ratio (CR) is calculated as: [CR= [3 ] where ?RI? Random Consistency Index. Random consistency indices are given in Table 2. [ ] Table 2. The consistency indices of randomly generated reciprocal matrices As a general rule, a consistency ratio of ?0.10? or less is considered acceptable. In practice, however, consistency ratios exceeding ?0.10? occur frequently. THE FMADM METHODOLOGY The FMADM methods have been developed due to the lack of precision in assessing the relative importance of attributes and the

Jan 1, 2009

By Christopher J. Bise

INTRODUCTION Before a mine is planned in detail, a preliminary analysis is often conducted. This preplanning permits the mining engineer to make a rapid assessment as to whether or not a particular mining property warrants further consideration. In fact, a properly conducted preplanning phase can come within 10% to 20% of the actual results, thereby saving the mining engineer valuable time before committing himself to a fine-tuned analysis. The questions to be answered by mine preplanning are (1) What will be the operating conditions for the mine? and (2) How long will it take to complete the project? To answer these questions, calculations dealing with reserve estimation, production planning, man- power planning, and project scheduling are conducted. The following sections discuss these various phases of mine preplanning in greater detail. RESERVE ESTIMATION The estimation of the various characteristics of a reserve, such as quantity, grade, and thickness, is an ongoing process throughout the life of a mining venture. However, the reserve-estimation phase of mine planning is more closely associated with the preplanning phase. There are many different techniques employed in reserve estimation of solid mineral deposits; variations among them are introduced because of such considerations as ease of application or level of accuracy. In any event, each technique is developed in the following manner: (1) the mineral body is represented pictorially and then subdivided into blocks related to one or more samples of exploration data, (2) the area and volume of each block is determined, (3) the volumes are converted to representative tonnages (or, for example, grades), and (4) the results are tabulated. To illustrate this procedure, the polygonal (area-of- influence) technique will be presented due to its ease of application, flexibility in dealing with different deposits, and general acceptance. The polygonal method assumes that all characteristics of a mineral body extend halfway between a point of observation and any other point of observation. The explored portion of the mineral body is represented by polygonal prisms whose depths relate to the characteristic in question (grade, thickness, etc.) and whose plane bases relate to the area of influence of each point of observation (drill hole, etc.) as shown in Fig. 1. The polygons must be constructed in a definite order, usually clockwise and from the periphery to the center of the deposit. Table 1 can then be used to calculate the characteristics in question. Since, by definition, the polygonal method assumes that the characteristics of a mineral body extend half- way between points of observation, it becomes readily apparent that the evaluation of a vertical-drill hole exploration program requires that the sides of the polygons be formed by the intersection of perpendicular bisectors (Fig. 2). Figs. 3 and 4 show correct and incorrect construction of the polygons. The criterion for correct construction of the polygons is that all points within a particular polygon must be closer to its rallying point than those located in any other polygon. This is clearly not the case for certain points that are located in the polygon containing rallying point B in Fig. 4. Although this method can be used where the drill holes are irregularly spaced, calculations become less tedious when a square net (Fig. 5) or a chessboard (Fig. 6) grid is adopted. The numbers shown in Figs. 5 and 6 represent the relative weight for each of the shaded areas. In general, the greater the number of polygons, the more continuous the mineral body, and the more regular the grid, then the more accurate the computations will be. PRODUCTION PLANNING Before an acceptable evaluation of the production potential of a mine can be determined, a thorough exploration program should be conducted. It seems obvious that the nature and properties of the deposit and adjacent strata, the presence of impurities, and other mining conditions should be adequately determined prior to production planning and equipment selection. The lack of sufficiently detailed knowledge of the many mining parameters has led to the failure of numerous operations. For example, targeted production tonnages and equipment sizes for a coal mine are intimately related to the seam thickness. Needless to say the quality of information that is gathered from an exploration program can have a tremendous impact on the production plan. Production plans are developed initially by determining reasonable shift tonnages per operating section. Most of the time these values are developed from his-

Jan 1, 1986