Search Documents

By Taner Sumer, H Altay Guvenir

Fragmentation in rock quarries is tried to be achieved by changing the specific charge, drill pattern and bore hole diameters by different experts. This paper is a brief summary consisting of the utilization of practical experiences of the other group on cost optimization procedure that takes into account blasting, transportation and crushing as a whole process and optimize the cost by defining the optimum gelatin based explosives to be used as a main primer of anfo in three different limestone and granite quarries, with similar rock characteristics.

Jan 1, 1993

By K. Meyer, M. E. Goddfellow

"At Teck-Corona Operating Corporation's David Bell Mine, a water quality management strategy is employed to produce both a chemically and biologically clean effluent prior to discharge to the environment.The strategy includes operating methods to minimize contaminants leaving the concentrator and an effluent treatment plant for cyanide, antimony, and heavy metal removal of concentrator, mine and site waste streams.Concentrator practices, the effluent treatment plant, process chemistry and the present day performance of the water quality management strategy are reviewed.INTRODUCTIONThe David Bell Mine is located in the Hernia gold camp 35 km east of Marathon, Ontario. The concentrator has a design throughput of 1,000 tonnes per day. ROM ore (-6"") is ground in a semi-autogenous mill followed by a ball mill, thickener, leaching, and carbon-in-pulp gold recovery unit operations. The concentrator flow sheet is shown in Figure 1."

Jan 1, 1991

By Raj K. Rajamani, Sanjeeva Latchireddi, Dave Plummer, Stieger. Julius

"The Cortez SAG mill liner design was recently modified to improve the mill operating energy efficiency. In addition to the expected benefits, the design change unexpectedly played a significant role of verifying the proposed grinding circuit expansion for the Cortez Hills project as well as illustrating current SAG mill bottlenecks. This paper will discuss the evaluation that addressed operator and maintenance observations, historical PLC data, and “crash stop” observations to calculate charge motion, packing between lifters, and slurry transport through grate and pulp lifters. The performance of the new shell and discharge end liner design will also be discussed as well as their role in the possible grinding circuit expansion.INTRODUCTIONCortez Gold Mines commenced operation in 1969 with its Mill #1 rated at a nominal 2,000 tons per day. Mill #1 was a conventional rod mill/ball mill circuit followed by an 8-stage CIP circuit. In the early 1990s the Pipeline deposit was discovered and subsequently Mill #2 was built to process the increased ore volume. Mill #2, commissioned by mid-1997, was a nominal 10,000 tons per day SABC circuit followed by an 8-stage CIL circuit for oxide gold ore. Operating and commissioning details of this plant have been published elsewhere (Powell, 1998). By late 1998, there was not enough ore volume to support both mills so the smaller, higher operating cost Mill #1 was put under its current care-and-maintenance status. A simplified flowsheet of the current mill is shown in Figure 1."

Jan 1, 2007

By Jonas Olsson

"The picture of China as an antiquated continent is changing rapidly and fast-forwarding progress is a fact in most infrastructural fields. Mining is not an exception. China is today the largest producer of aluminum, coal, steel, zinc, tin, lead and manganese and the country’s mineral resources comprising approximately 12% of the global reserves ranks them number three in the world after US and Russia.In order to feed the growth industry is needed to take extra ordinary strides to improve supply of raw material and Chinese mines are continuously being upgraded with the latest western technology to meet the increasing domestic demand of base metals.In Anshan located in China’s northeast province Liaoning we find one of the fastest developing mining companies, Angang Iron & Steel Group Co. Ltd. With their six mines that together process approximately 60 M ton iron ore/year Angang Iron & Steel Group Co. Ltd is the largest iron ore company in China. The group’s thorough pre-studies and technical evaluations over the past five years have made them very successful in both plant upgrades of existing operations and green field projects.INTRODUCTIONWe live in a time when the world market is gradually acclimatising to the global consequences of “The China effect”. An effect caused by a formerly sleeping giant nation that during the last years has awakened and developed beyond comparison, primarily because of booming infrastructure projects and demand for capital and consumer goods"

Jan 1, 2006

By Heather N. Dougherty

In the absence of values for each influencing parameter and a known relationship of input-output space, novel approaches should be implemented as proxy solutions to mathematically complicated problems. Proxy solutions can be in the form of linear or non-linear multiple regression equations. Predicting the performance of gob gas ventholes is one of these mathematically complicated problems as it is difficult to know the exact relationships between various parameters influencing gob gas venthole (GGV) performance from active and sealed (completed) longwall panels. In this paper, a discussion of the NIOSH-developed software suite for methane control and prediction (MCP) based on an artificial neural network (ANN) is presented. The application of the ANN-based software suite to develop algebraic relationships for gob gas venthole performance prediction in sealed and active longwall panels is sought. Output information obtained from the NIOSH-MCP software as a response to various input parameters were used to create an input-output database for total flow and methane percentage from GGVs operating in active mines during completed and sealed panel situations. Due to the multi-variable nature of the software, outputs generated using the software for various inputs were used to develop analytical equations first using linear and then second using non-linear multivariable regression techniques. The advantage of this method is its ability to better understand the significant parameters of the relationships between the inputs and outputs for gob gas venthole production in active and sealed panels and to be able to predict their performances using relatively simple analytical functions.

Jan 1, 2010

By Wenshan Zhang

Three important methods of removing Fe in hydrometallurgy of zinc, manganese, copper, nickel, cobalt and etc are described, including neutralized hydrolysis method, jarosite method and goethite method. The reactions, technical requirements and thermodynamic analysis during Fe removal process are also discussed in this paper.

Jan 1, 2006

By P. Cole Gregory, Michael R. Yenchek, John C. Edwards

The U.S. Bureau of Mines investigated the performance of portable power cables under transient conditions. This research had a twofold purpose: (1) to define the thermal characteristics of electrically overloaded trailing cables, and (2) to conceptualize electrical protection for cables that allows maximum cable efficiency without diminishing electrical safety in underground mines. Several tasks were under- taken in support of these goals during the 3-year research effort. Overload tests ranging from 2 to 12 times rated ampacity were conducted in the Bureau's Mine Electrical Laboratory. Two thermal models of energized type G-GC trailing cables were constructed, one based on thermodynamic theory and the other using empirical data from previous Bureau load tests. The empirical model was then incorporated into an interactive computer program that can assist designers and approvers of mining machines in selecting the appropriate size trailing cable. This program can be the basis for a cable protection system that ensures that cables are not the source of fires, ignitions, burns, or explosions underground.

Jan 1, 1993

By Hyung Jeek Kim, Jongmin Joo, Jonguk Kim, Jai-Woon Moon, Kyeong-Yong Lee

"Co-rich ferromanganese crusts (Fe-Mn crusts) distributed on seamounts in the western Pacific are potential economic resources for cobalt, nickel, platinum, and other rare metals in the future. Evaluation and selection of a mining site can be established based on abundance and grade of Fe-Mn crusts in the site as well as topography that should be smooth enough for mining operations. Therefore, acquisition of shipboard echo-sounding and acoustic backscatter data are prerequisite to the selection of potential mine sites in addition to visual and sampling operations. Acoustic backscatter data can be used to locate crust-covered areas on a regional scale with the understanding of acoustic properties of crust through its correlation with visual and sampling data.During an expedition that took place from January to March 2014, KIOST collected geophysical and geologic data to assess the resource potential for Fe-Mn crusts on three seamounts (guyots) in the Western Pacific. In OSM11, one of the three surveyed seamounts, three camera tows were performed to observe the distribution of Fe-Mn crusts on the summit and slopes of the seamount. Although sediments of various thicknesses generally cover most of summit region of OSM11, several regions with high backscatter signals occur on the periphery of the summit. The occurrence of Fe-Mn crusts, observed during the camera tows, on those high backscattered regions suggests that the backscatter signals of shipboard multi-beam sonar can reflect changes in the geology of the seafloor from sediment layer to Fe-Mn crust deposits. The Fe-Mn crust deposited around the summit region is worthy of notice because of its topographic characteristics, including shallow depth, flat or gentle inclined surface, and smooth relief, which are more suitable for mining operation compared to the flanks of seamount."

Sep 1, 2014

By Zorigtkhuu Davaanyam, Bern Klein, Stefan Nadolski, Amit Kumar

"The High Pressure Grinding Rolls (HPGR) is a relatively new comminution technology that has been shown to be more energy efficient compared to semi-autogeneous (SAG) mills. Full and fair consideration cannot be given to HPGR-based comminution circuits in early stage projects, because presently pilot scale testing is required for assessing and sizing; pilot scale testing requires bulk samples weighing more than one tonne. A CAMIRO research program was conducted at the University of British Columbia to develop bench scale tests that would reduce the quantity of sample required to assess HPGR.Three test procedures were developed.1. The Direct Calibration Methodology calibrates piston press test results to pilot scale test results such that piston press tests can then be used to determine the energy–size reduction relationship for a range of ore types.2. The Database Calibrated Methodology, which is similar to the Direct Calibration Methodology except that it calibrates piston press tests against a database of pilot scale and piston press tests.3. The Semi-Mechanistic Methodology was developed to use piston press test results as an input for an HPGR based energy-size reduction performance model.Through utilization of these methodologies, the energy–size reduction performance of an HPGR can be predicted with minimal sample requirement. In addition, piston press testing is far more cost effective, faster, and accessible than pilot-scale HPGR testing.IntroductionOne could argue that in the future, decisions regarding selection of comminution circuits will be made primarily on the basis of energy consumption. The following facts and predictions support the argument:"

Jan 1, 2015

By Ove Alm

Wet and dry specimens of three rocks of approximately granitic composition were deformed at different experimental conditions. These experiments were carried out in order to study the extent to which water, either added or released from mineral reactions, may affect the mechanical properties and the microstructure of these rocks. The experiments were conducted in a Griggs&apos; hot creep apparatus at temperatures and pressures up to 900ºC and 1000 MPa respectively; and most of them were performed in the constant strain rate mode [(1.10-6 < t < 1 • 10-4 s-1 )]. All three rocks were low porosity rocks, and the wet specimens never contained more than 0.9 wt % of added water. The experimental results are, however, quite unequivocal: They show that wet rocks are weaker than dry ones. A significant difference is even found for rocks tested in uniaxial compression at room temperature. A few experiments carried out on specimens obtained from larger prestressed rock cores indicated that the central parts of these cores were more likely to contain more microcracks than the ends. Optical microscope examinations revealed that extensive microcracking takes place even at the highest temperatures, where other mechanisms such as slip and dislocation creep also become important. Very little partial melting could be observed except for the specimens deformed at 900ºC.

Jan 1, 1982

By Lukasz Maciag, Ryszard Andrzej Kotlinski, Ryszard Krzysztof Borówka, Dominik Zawadzki

Concentration and composition of rare earth elements (REE) and major elements in the sediment samples from the IOM H11 Fe-Mn nodule deposit, eastern part of the Clarion-Clipperton nodule field (located between the Clarion-Clipperton Fracture Zone - CCFZ; tropical Pacific), have been studied. We show the controls on REE concentrations and described vertical/horizontal variability of selected metals in pelagic sediments from the CCFZ. According to Kato et al. (2011), who analyzed 2000 seafloor sediment samples at 78 sites of the Pacific Ocean, deep-sea mud shows high concentrations (2230 ppm maximum) of ?REY and could be potential resource of these elements in the future. However, our work does not fully confirm that sediments in the IOM H11 are significantly enriched in REE.

Sep 1, 2014

By B. E. Davis

Over 80 pct of domestic phosphate rock, which is the starting material for phosphorus-containing fertilizers, comes from central Florida deposits. As K-her grade deposits are depleted, lower grade phosphate ores containing &apos;Mg0 in the form of dolomite are encountered. Treating high MgO ores with present beneficiation technology will not yield a concentrate meeting specifications for acidulation. The Bureau of Mines conducted research on three high-MgO phosphate samples from south Florida. The sales contained, in percent, 5.4 to 10.2 P205, 1.9 to 7.6 MgO, and 35.3 to 60.1 acid insolubles. A technique of sizing, grinding, desliming, scrubbing, and redesliming was used to produce a feed suitable for continuous flotation studies, A conventional fatty acid-fuel oil rougher flotation followed by two to three cleaner stages resulted in concentrates containing, in percent, 30.7 to 31.3 P205, 0.6 to 1.3 MgO, and 2.5 to 4.8 acid insolubles. The P205 recovery from the flotation feed ranged from 55.1 to 89.7 pct.

Jan 1, 1984

By Randall M. Wheeler

"Fourier analysis is a very powerful frequency analysis tool. However, it is frequently misunderstood and sometimes used inappropriately. Part of this workshop will involve the basics of Fourier series, the Fourier integral and finally the Fourier transform. Included will be a brief discussion of analysiswindows, including the box and Hamring windows."

Jan 1, 1998

By Edward Walter

Rock excavation for tunneling projects occurs on a regular basis in the Cleveland area. These tunnels are being constructed to increase the capacity of the sanitary sewer system. Controlled blasting must be performed to remove rock in a number of phases of the project. The rock excavation for construction of a junction chamber is just one case where blasting is the safest and most efficient method available.

Jan 1, 2001

By R. W. Lawrence

"Biological leaching can be used to enhance the recovery of gold and silver from refractory ores, concentrates and tailings. The method liberates precious metals associated with sulphide minerals such as pyrite and arsenopyrite making them amenable to cyanidation. The chemistry and features of biological preoxidation leaching is discussed. A summary of the results obtained on various ores, concentrates and tailings is presented.INTRODUCTIONRefractory precious metal ores in which gold and silver are finely disseminated in sulphide minerals such as pyrite and arsenopyrite are becoming more important to the mining industry. This is due both to a depletion of simpler, free-milling ores and to a significant increase in the price of gold in recent years. Whereas many ores can be directly cyanided with gold solubilizations over 90% obtained, the refractory ores respond poorly to direct cyanidation and require decomposition of the precious metal-bearing sulphide minerals to increase recoveries.Decomposition of sulphides by oxidation prior to cyanidation can be carried out by several means. The oldest method is roasting which removes unwanted ore constituents by high temperature oxidation and volatilization. In Canada, for example, roasting is used at Giant Yellowknife (Connell and Cross, 1981). Another method gaining increasing acceptance is pressure hydrometallurgy which uses aqueous oxidation conducted at high temperature and pressure. Homestake Mining Company have recently completed construction of a plant incorporating pressure oxidation at their Mclaughlin property in California (Guinivire, 1984)."

Jan 1, 1985

By Dale S. Preece

The computer program. DMC Qistinct Motion &de), which w&s developed for simulating the rock motion associated with blasting, has been used to study the intluence of row delay timing On rock mOtiOn. The munerical simulations correspond with field observations in that vmy short delays (< 5Oms) and vety long delays(> 3oOms) produce a lower percent-cast thao a medium delay (100 to ZOO ms). The DMC predicted relatio&lp between row delay timing and percent-cast is more complex than expected with a dip in the auve where the optimum timing might be expected. More study is required to gain a full undasranding of this phenomenoo.

Jan 1, 1994

Impala Platinum?s No.16 Shaft mine is currently under construction and is expected to reach full production of 256 500 tons per month by 2014. Mining will start at 1 260 m below surface with a maximum mining depth of 1 535 m where virgin rock temperatures of 56.6°C will be experienced. As a result of depth, high virgin rock temperature and narrow reef mining, an expected total of 31.5 MW[R] of air cooling capacity will be required to achieve acceptable underground conditions. This will be achieved by cooling mine intake air in a single dedicated air cooling installation located on surface. The compact installation includes air cooling spray chamber, refrigeration machines, condenser cooling towers, evaporator and condenser water reticulation as well as all electrical and control systems. Construction and commissioning of the first phase of this air cooling installation has recently been completed on a turn-key contract basis.

Jan 1, 2009

THE object of the present paper is to give a brief description of the metallurgical process followed by the Grand Junction Co, and the results obtained therefrom. All figures quoted are from the actual working of the plant over a period of six months from January to June, 1910. The short ton of 2000 lb. is used by the company. Its gold is valued at 84s. per oz. fine, silver at 2s. per oz. fine. The ore consists essentially of a gangue of quartz and calcite, with 8 to 10%sulphide-pyrite, sphalerite, galena, chalcopyrite, and traces of arsenic and antimony. The colmtry-rock is a highlyaltered dacite. Small stringers of highly-mineralized ore penetrate the footwall of some of the lodes, forming a valuable stockwerk up to 3 ft. in thickness. In stoping, this is mined with the well defined lode, thus bringing into the mill at times a considerable quantity of hard country-rock. The gold exists in an exceedingly fine state of division, consequently rendering it necessary to grind very fine to obtain a satisfactory extraction.

Jan 1, 1912

By R. A. D. Pattrick, R. A. F. Ixer

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. At Calliachar Burn, 14 steeply dipping quartz-sulphide veins, with and without gold, infill master joints that crosscut gently dipping metasediments and metabasics of the Pitlochry Schist Formation. The wallrock is extremely bleached and enriched in sericite, chlorite and carbonate. Gold grades vary from high with quartz-galena-pyrite to low with galena-chalcopyrite; the gold forms electrum inclusions smaller than 20 micrometres in pyrite or, rarely, arsenopyrite. At Urlar Burn, gold is present in small amounts in 4 quartz-galena-chalcopyrite veins. Although much of the mineralogy is similar to that at Calliachar, there are significant differences in Sb-, Te-, Bi- and Hg-bearing phases. Fluid inclusion data suggest mineralisation occurred over the range 320-140 degrees C, from fluids with significant CO2 and 2-13 wt% equiv. NaCl. Mantle-derived fluids appear to have been generated during the late Caledonian and focused by the Urlar Burn fault

Jun 19, 1905

By H. S. Rathor

NTPC (National Thermal Power Corporation), a multi-unit organization, is generating 26% of India’s total power. This power is produced from its 14 coal based stations and 7 gas based stations. NTPC is entering into the business of power-distribution, power-trading, setting up of coal mines and diversification in non-conventional energy sector as well. For achieving the goal of the country “Power for All” NTPC has taken a giant stride by entering into Hydro Power generation which is also the cheapest and the cleanest renewable source of energy. In its pursuit for excellence, 800 MW Koldam Hydro Power Project is NTPC’s first venture in hydro sector. In Koldam, hydropower potential will be harnessed by constructing a 163m high earth and rock fill dam in a narrow gorge at upstream end of Bhakra reservoir. The river diversion is envisaged through two parallel, 14m finished diameter ‘horseshoe’ tunnels of length 901m and 934m at village Kian on the right bank, where the river forms a 180° loop. The diversion tunnels are designed to accommodate a flood of 6500m3/sec, taking into account the maximum probable discharge of 200 years return period. The tunnels pass through dolomite and limestone rock formations. The excavation of tunnels was done with drill and blast method. The excavation was attempted from both inlet and outlet faces. During geological investigation a rock fault was located at the outlet area. The location of the fault was such that it was passing through the edge of the Tunnel-1portal and around 30m away from the face of the Tunnel-2 portal. The quality of the rock at Inlet was also poor. To save the portals from slips, excavation of the tunnels was planned to start after the completion of the open excavation and its support system both at inlet and outlet. The tunnel excavation at inlet was envisaged by approaching the tunnels’ portal by constructing a road through 540EL bench and meeting the inlet portals on the upstream end, which would have been ready by mid2003, only after completion of the open excavation and its support system. To save time and cost, it was felt necessary to modify the planning by starting the tunnel excavation simultaneously along with open works both at inlet and outlet. The excavation at the inlet face of the tunnels started in December 2002 after rerouting the approach road to inlet portals through haulage road on the downstream and similarly Tunnel-1 at the outlet was started in the low cover area before completion of open area works. Thus the tunnel—heading excavation was started nearly 06 months early with the change of methodology.

Jan 1, 2005