Search Documents

By O. M. McRae

The Courtland-Gleeson area is in Cochise County about 15 miles east of Tombstone in southeastern Arizona. Rocks exposed in the area range in age from Pre-cambrian to Quaternary. The Precambrian is repre-sented by the Pinal schist. Paleozoic rocks include the Cambrian Bolsa quartzite and Abrigo limestone, Mississippian Escabrosa limestone, and the Permo-Carboniferous Naco Group limestones. Rocks believed to be of Triassic and/or Jurassic age include the Copper Belle monzonite porphyry, Turquoise granite, and Gleeson quartz monzonite. The Cretaceous is represented by andesitic volcanics and various sedimentary rocks. Tertiary rocks include the intrusive and extrusive Sugarloaf quartz latite porphyry and numerous dikes of various rock types. Quaternary conglomerates cover the northern and eastern part of the area. The geologic structure is extremely complex. All rocks as old as early Tertiary have been involved in either tilting, normal faulting, high angle reverse faulting, imbricate thrusting or folding and overfold-ing. Major deformation was initiated during the first half of the Tertiary. Northeast-southwest compres-sional forces caused thrust plates containing lower Paleozoic rocks to override Cretaceous rocks. Subsequently, two large slide blocks of lower Paleozoic rocks, acting under the influence of gravity, moved eastward. The imbricate structure and the gravity slide blocks were then broken by late Tertiary normal faults. INTRODUCTION The Courtland-Gleeson area, or Turquoise Mining District, has long been recognized as an area of extreme structural complexity. Gilluly 2 referred to the entire district as a "gigantic thrust breccia". In 1962, Bear Creek Mining Company completed a two year program of detailed geologic mapping supported by exploration drilling. The purpose of this paper is to present some of the results of this investigation and to provide a structural interpretation based on these results. The geologic map that accompanies this report is generalized and shows only the major and significant features. The area was initially mapped on aerial photographs on a scale of 1 in. equals approximately 500 ft. These data were transferred to a planimetric base using a vertical sketch master. LOCATION The Courtland-Gleeson area is in central Cochise County, about fifteen miles east of Tombstone, and about twenty-two miles northeast of Bisbee in southeastern Arizona (Fig. 1). The area is readily accessible over graded gravel roads from both Tombstone and Elfrida. GENERAL GEOLOGY Rocks exposed in the area range in age from Pre-cambrian to Quaternary. wilson3 and Gilluly2 have published very detailed descriptions of the principal rock units exposed in the area. Only a summary description is provided in Table I. A great number of previously unmapped narrow Tertiary dikes and small irregular masses of hornblende andesite porphyry, lamprophyre, and aplite intrude the Gleeson quartz monzonite in the western part of the map area. The scale of the map prohibits showing them. The aplite dikes are related to, and bear the same structural relationships as, the Sugarloaf quartz latite dikes found in this area. For that reason, and because both the hornblende andesite porphyry and the lamprophyre are post-mineral and post-thrusting, their omission from the map is not considered significant. Because so many of the contacts in the district are fault contacts, because bedding faults appear to be prevalent but are difficult to recognize and map, and because igneous intrusions are so common throughout the sedimentary section, it is virtually impossible to measure an exact total thickness of any of the sedimentary rock units. Nevertheless, neither the field mapping program nor the diamond drilling provided any basis for suspecting that the thicknesses of the sedimentary units are significantly greater or less than what might be inferred from surrounding districts.

Jan 1, 1967

By D. B. Felsher

"Lakeshore Gold’s Bell Creek Mill is located in Timmins, Ontario. The mill has been in operation since 2009 and has undergone several small expansions since then. In 2012 - 2013 the first major mill expansion was commissioned raising the mill capacity from 2,000tpd to 3,150tpd. This was done through the installation of a new ROM ore truck dumping facility, jaw crusher, ore storage dome, SAG mill, leach tank, CIL tank, and electrowinning cell. This paper will cover the equipment installed to raise the tonnage as well as the commissioning of the new equipment including problems encountered and how these problems were solved.IntroductionLake Shore Gold acquired the Bell Creek Mill, along with the Bell Creek Mine, from the Porcupine Gold Mines Joint Venture, a joint venture between Goldcorp Canada Ltd. and Kinross Gold Corporation, in December 2007.The Bell Creek mill, which processed ore from the Bell Creek Mine has consistently achieved recoveries of over 95%, is a conventional gold mill circuit, involving crushing and two stage ball mill grinding, gravity and leaching, followed by Carbon-In-Pulp (CIP) process for gold recovery. The facility had been placed on care and maintenance in 2002. At the beginning of 2009, the mill had been refurbished with an initial capacity of 800 tonnes per day and was subsequently refurbished to a capacity of 1,500 tonnes per day near the end of the third quarter of that year. The Mill was then expanded in 2010 to a capacity of 2,000 tonnes per day.In late 2011, the Company commenced a 50% expansion of its milling facility, from a processing capacity of 2,000 tonnes per day to 3,150 tonnes per day. Phase 1 of the expansion, which mainly involved enhancements to the solution circuit (“back end”) and increased the mill’s capacity to 2,500 tonnes per day, was completed at the end of 2012. Commissioning of Phase 2 of the expansion, to a capacity of 3,150 tonnes per day, commenced at the end of July 2013."

Jan 1, 2015

By M. Abdellatif

Keywords: Magnesium, pyrometallurgy, Mintek Extensive testwork on atmospheric thermal magnesium production has highlighted certain important fundamental and operational factors that have a major influence on magnesium extraction and its extraction rate, the condensation efficiency of magnesium, as well as on the quality of the condensed metal. The possible impact of these factors on the selection and preparation of raw materials, recipe choice, furnace electrical energy consumption, and on the refining requirements of the crude magnesium is discussed. Selected pilot plant operational and metallurgical data are also presented.

Jan 1, 2006

By S. J. Jung

The most frequent causes of accidental injury and fatality are carelessness and ignorance; and the most common accidents are haulage accidents, fall, drowning, and fire. However, in this modern day and age, severe injury has become the dire consequence of an ever-increasing number of industrial and mining accidents as well as sport-, military- , etc. Mine accidents have declined dramatically in number and severity through decades of research, technology, and preventive programs. However, preventing recurrence of disasters like those of the past remains a top priority requiring constant vigilance by management, labor, and government. The goal of the present research is to investigate and identify root causes associated with types of mining accidents (victim being caught by an equipment, bodily motion, over exertion, etc) and nature of injuries such as (sprain and strains, fracture, dislocation, amputation, etc). Further, we hope to discover the impetus of the root causes occurring more and more often in this modern day of technology and quality awareness. With the different dimensions of accidents and injuries brought into the fold, there is the need for researchers and mining operators to comprehend and better still visualize significant patterns of associations among these variables of interest. We assume that, there is a high correlation between many dimensions of nature of injuries and types of accidents. This suggested a principal component analysis to reduce the dimensions for easy and amenable interpretation.

Jan 1, 2012

By Dale Dean, Bill Hancock, Raul Mondragon, Carlos Aguilar, Chris Martin

"In 1942, commercial mining operations began in what is now the Lucky Friday Ag/Pb/Zn mine in Idaho’s Silver Valley. Wholly owned since 1962 by Hecla Mining Company, the mine has produced more than 145 million ounces of silver and has been a mainstay producer in Idaho’s Silver Valley for over 70 years.However, by the early 21st century, the mill had fallen, technologically, seriously behind the rest of the industry. Accordingly, starting in 2005, the current mill management team set to revitalizing the milling operation. This paper will describe how the mill was systematically evaluated and the aging infrastructure replaced with more current technology. Driven by internal mill review studies supported by QEMSCAN mineralogical balancing, the mill has in recent years been through waves of upgrading – from the installation of new mechanical and column flotation equipment to the introduction of on-stream analysis, a technology well-accepted around most of the industry but alien to this technologically conservative mining district.The experience at Lucky Friday is a testament to the need for ongoing structured mill optimisation and technology upgrading in established mining operations. This paper will describe engineering experiences associated with upgrading equipment in an operating mill, contained in a confined building. Experiences in teaching the team new ways of operating a mill, and finally the metallurgical rewards that have been reaped will be described.INTRODUCTIONMining in Idaho’s Silver ValleyIdaho’s Silver Valley is a 64-km long valley flanked by the US Northern Rocky mountains, seldom more the 3-km wide, and stretching across much of Idaho’s northern panhandle, roughly 150 km south of the Canadian border. Mining has been continuously active in the area for more than 140 years, during which time, the Silver Valley has become one of the richest silver producing districts in the world, and as of 1985 had out-produced the 500 years of production from the famed Potosi district in Bolivia. Since 1885, almost 100 deposits have been discovered and worked in the district (Chapman, 2000)."

Jan 1, 2011

By P. O. Metz, E. L. Wiehe, J. S. Foster

BASED on their analyses of growth kinetics, ibbs' and Harris et al.' have recently proposed that the rate of subcritical graphitization of steel is controlled by the rate of diffusion of carbon in ferrite. illert has concluded that this is the rate controlling growth mechanism when the growing graphite particles are relatively large. Harris et al.' also propose that the matrix surrounding a growing graphite particle is plastically deformed to make room for the growing particle. If this plastic deformation does occur, then preferred recrystallization may be observed around the larger particles. If diffusion of carbon in ferrite is rate controlling, then a graphite particle growing in a matrix of, say, tempered martensite or pearlite, should be surrounded by a carbide depleted zone. Thus, the simple metallographic experiments reported here are sufficient to determine whether or not diffusion of carbon in ferrite is the dominant mechanism for the growth of graphite in steel. The present investigation considers graphitization in five alloys. The compositions are given in Table I. Graphitization was carried out at three temperatures: 900°K (627"C), 950°K (677"C), and 990°K ('717°C). Samples were reacted in both the martensitic and the pearlitic initial conditions. In the hypoeutectoid steels, Sets 7 and 8, .and in the hypereutectoid Fe-C binary, Set 6, graphitization was very limited after 1000 hr at temperature. In these samples graphite particles observed were less than 10 p in diam. In the hypereutectoid commercial steels, Sets 1 and 3, large graphite particles (100 p) did not appear until after 250 hr at temperature. The limited number of graphite particles observed and the range of sizes obtained prohibited measurement of growth rates in this investigation. However, in all samples showing graphitization, neithe a carbide depleted zone nor recrystallization was observed. illert's model predicts that diffusion of carbon in ferrite should become dominant for graphite particles larger than about 300 p in diam. The largest graphite particle observed in this investigation was approximately 450 p in diam. No evidence of carbide depletion was noted. Fig. 1 shows a typical graphite particle. This nodule is from an initially pearlitic sample from Set 3 after

Jan 1, 1970

By Christopher J. Bise

INTRODUCTION The principal means for transporting men, supplies, and mined material in an underground or surface mine are rail systems, conveyor belt systems, or a combination of the two. Typically, large underground mines use rail haulage from the mining sections to the hoist, with conveyor belts being used within the sections. Small mines use conveyor belts in the mains and sub- mains as well as in the panels. The size and layout of surface mines also contribute to variations in the way these haulage systems are applied. The following sections address the typical problems confronting mining engineers in designing these haul- age systems. For rail, these include rail selection and turnout design, locomotive tractive-effort calculation, and motor sizing. Belt haulage calculations include belt width and speed specifications, tension and take- up requirements, idler spacings, and motor sizing. TRACK LAYOUTS Introduction The adequacy of mine track layouts is dependent upon such factors as rail weight (Table l), suitable ties, a well-drained roadbed, and properly designed curves, grades, and track alignment. As long as the installation conforms to the manufacturer's recommendations, good service can be expected from the rail system. Typically, mining-engineering calculations for rack layouts have dealt almost exclusively with the design of turnouts. As such, the following section provides the necessary information for computing the theoretically correct dimensions of turnouts. Turnout Design Fig. 1 shows a typical turnout with an identification of the component parts. Fig. 2 identifies the variables that are used to determine the turnout dimensions. The formulas that concern the mining engineer are those listed: [ ]

Jan 1, 1986

By L. Li

The rock quality designation (RQD) was initially introduced by Deere (1963) for civil engineering. But, its application has been largely extended to rock mechanics and has become a fundamental parameter in geotechnical engineering (e.g., Hoek & Brown 1980; Milne et al. 1998). The success of this definition is due, in great part, to its simplicity. However, this index includes a number of limitations. Among these limitations, a critical one is associated with the arbitrarily selected threshold value (e.g., Priest & Hudson 1976). Consequently, the RQD value would vary with different threshold length for the same core. Also, using the customarily and universally adopted but very arbitrarily selected threshold value of 10 cm (for NX cores) in the assessment of RQD, the RQD values usually tend to be either high or low in most rock engineering. Some intermediate values (50%) are less frequently encountered (Harrison 1999). The original definition of RQD does not well represent the actual quality of rock masses. In this paper, an improved definition of rock quality designation (RQDc) is given.

May 1, 2009

By Zhouhua Jinag

The attempt has been made to manufacture high nitrogen austenitic stainless steels by pressurized electro-slag remelting furnace with maximum nitrogen pressure of 7MPa. To obtain high nitrogen content in steels, the compound electrodes with different nitrogen sources (FeCrN, Si3N4) were prepared. Using the Si3N4 as the nitrogen alloying source, the silicon contents in ingots were prone to be out of the specification range, and the electric current fluctuated greatly and the surface qualities of the ingots were poor. The surface qualities of the ingots were improved using FeCrN as nitrogen alloying source. The sound and compact macrostructure ingot with the maximum nitrogen above 1.0wt% could be obtained. A series of high nitrogen austenitic stainless steels have been successfully developed by this method. The mechanical and pitting corrosion resistance properties of high nitrogen austenitic stainless steels were investigated. The results show that the steels exhibit excellent mechanical and pitting corrosion resistance properties.

Jan 1, 2009

The Australian Centre for Minesite Rehabilitation Research (ACMRR) was established through a mining industry initiative to meet the need of industry, governments and the community for sustainable systems for land affected by exploration, mining and mineral processing activities. The Centre, which is a consortium of the major groups associated with mining rehabilitation research in Australia, has a focus on both strategic research and technology transfer and combines a wide range of multidisciplinary skills covering engineering and the physical and biological sciences. The paper briefly describes the goals, structure, expertise and research and technology transfer activities of the Centre. The major research program areas of waste rock dump and final void stability, acid mine drainage, tailings disposal, and remediation of ecosystem reconstruction are described in the context of national priorities.

Jan 1, 1995

By Thomas O. Glover

Cameroon's mineral industry continued to be dominated by crude petroleum. The country's economic development depended on the production and export of crude oil. Oil output was estimated to be 56 million barrels in 1984 compared with 47 million barrels in 1983 and 39 million barrels in 1982. The country's only refinery processed approximately 16,000 barrels per day of crude oil in 1984, operating at slightly over 50% capacity. This volume, however, supplied the domestic need for motor fuel and heating oils. Cameroon's economy continued to expand despite problems and setbacks stemming from the attempted coup of April 6, 1984. Gross domestic product (GDP) growth in 1984 was 6.5%, the same rate as in 1983. Offshore crude petroleum production was the chief factor in the sustained economic growth. The country also maintained a relatively strong balance-of-payments position through oil exports. Investment, ranging up to 25% of the GDP, greatly contributed to sustained growth. The oil sector contributed approximately 14% to Cameroon's GDP in both 1983 and 1984.

Jan 1, 1986

By R. Dahlke, J. A. Finch

A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick mine concentrator to investigate the role of gas (air) superficial rate (Jg) distribution to the cells in the final Zn cleaning stage (bank of seven cells), i.e. the Jg profile. Three profiles were tested: “balanced” (each cell with same Jg), “increasing” (from cell 1 to 7 proportionally), and “decreasing,” along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was the response of the first cells in the bank where the increasing profile gave the highest selectivity of sphalerite against nonsulphide gangue (NSG). The other profiles gave lower selectivity and higher zinc recovery in the first cells, which combined to reduce overall bank performance. The higher selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG. The increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.

Jan 1, 2004

Case I- Timber Pile Test- 4 pages describe the pile driving record, the pile load test and the boring log. Case II- 24 inch square prestressed concrete pile-5 pages give details about the pile driving, the boring log, the pile driving record, and the pile load test. Case III- 12 inch square prestressed concrete pile- 5 pages describe the compilation of SPT blow counts for the whole project, the pile driving record, the pile load test and the detailed boring logs. The 70 foot long pile was driven by a Vulcan 08 pile hammer. Case IV- 12 BP 53 Steel H pile- 3 pages give the pile load test, the pile driving record and the nearest boring log. The 64 foot long pile has its tip at elevation 908 ft. and the ground is at elevation 972 ft. The contractor augered to elevation 959 ft. before driving the pile with a Conmaco 08 single acting pile hammer. The hammer had an 8000 pound ram, a rated energy of 26,000 ft-1b., and a 7 1/2 inch thick asbestos cushion. Dynamic measurements were made during driving of the test pile and measured a hammer energy equal to 12,500 foot-pounds.

Jan 1, 1988

By F. Agterberg

In his 1978 monograph ‘Lognormal-de Wijsian Geostatistics for Ore Evaluation’, Professor Danie Krige emphasized the scale-independence of gold and uranium determinations in the Witwatersrand goldfields. It was later established in nonlinear process theory that the original model of de Wijs used by Krige was the earliest example of a multifractal generated by a multiplicative cascade process. Its end product is an assemblage of chemical element concentration values for blocks that are both lognormally distributed and spatially correlated. Variants of de Wijsian geostatistics had already been used by Professor Georges Matheron to explain Krige’s original formula for the relationship between the block variances as well as permanence of frequency distributions for element concentration in blocks of different sizes. Further extensions of this basic approach are concerned with modelling the three-parameter lognormal distribution, the ‘sampling error’, as well as the ‘nugget effect’ and ‘range’ in variogram modelling. This paper is mainly a review of recent multifractal theory, which throws new light on the original findings by Professor Krige on self-similarity of gold and uranium patterns at different scales for blocks of ore by (a) generalizing the original model of de Wijs to account for random cuts; (b) using an accelerated dispersion model to explain the appearance of a third parameter in the lognormal distribution of Witwatersrand gold determinations; and (c) considering that Krige’s sampling error is caused by shape differences between single ore sections and reef areas.

Jan 1, 2015

The mining industry to the lay mind is one which appears peculiarly dangerous, partly because the accidents which take place are usually of a very tragic nature, and partly because other, industries claim victims more from disease than fromviolence, and their fatal nature is not advertised to the same degree so that in spite of this idea of unusual risk, it is a fact that mining will compare favourably, as regards vital statistics, with nearly all other trades requiring special training.Neverthelessthere are a larger number offatal and serious accidents occurring year by year than one would like to see, and could the deaths which take place by accident be eliminated, it is safe to say that mining would become one of the most healthy of all species of skilled labour. If we examine the accidents appearing yearly in the reports of the Mining Departments of the various colonies, it will be at once admitted that many of them need riot, and in many cases ought not to, have occurred.It is, therefore, the object of tbis essay, to pass under review the ordinary precautions which should be adopted to minimise, as far as possible, the dangerous factors whereby fatalities are brought about.

NIOSH research has focused on the monitoring and the control of methane levels in active mine workings. Response times for instrumentation using catalytic heat-of-combustion sensor technology were evaluated. NIOSH research has modelled the flow of methane gas onto long-wall faces and gobs, developed engineering controls to limit methane levels during mining, and designed coalbed and gob degasification systems. Available methane control systems have been challenged by recent developments in longwall and room-and-pillar mining systems. This includes increased face advance rates leading to increased productivities, increased longwall panel sizes, and the generally deeper workings of U.S. coal mines. The potentially violent nature of any underground explosion or ignition requires the measurement, control, and reduction of methane emissions into the mine environment for continued worker safety.

Jan 1, 2008

By W Valery, S Morrell

In the mining industry blasts are usually designed to fracture the in situ rock mass and prepare it for excavation and subsequent transport. The run of mine (ROM) fragmentation is considered good when it is fine enough and loose enough to ensure efficient digging and loading operations. Mining optimisation strategy is hence usually focussed on minimising total mining costs and maintaining these ROM fragmentation characteristics. Although this approach ensures an efficient mining operation it ignores the potential impact on crushing and grinding. Investigations by several researchers have shown that designing blasts to produce ROM fragmentation to optimise crushing and grinding performance enhances the overall efficiency and profitability (Eloranta, 1995; Kojovic et al, 1995; Bulow et al, 1998; Kanchibotla et al, 1998; Scott et al, 1998; Simkus and Dance, 1998). Field experimentation in this area is often found to be difficult because of high implementation costs and insufficient understanding about the effect of fragmentation at different stages in a comminution circuit. Modelling and simulation of blasting and comminution processes provide a more economic alternative to explore the impact of blast design changes on the down stream operations (Kanchibotla et al, 1998; Kojovic et al, 1998; Adam and Siddall, 1998; Bulow et al, 1998). However, the reliability of such simulations depends on:the ability of the models to reproduce the physical processes that take place; characterisation of rock mass in terms of its blastability and comminution characteristics; and in the case of blast modelling the ability to predict fines (-10 mm) has been found to be particularly important as this fraction has a significant effect on mill throughput.

Jan 1, 1999

By L. Ozdemir, M. Cigla

This paper presents and discusses some of the computer models developed and currently used at the Earth Mechanics Institute (EMI) of the Colorado School of Mines (CSM). These include the performance models for full and partial face machines. Examples of input and output of these models will be illustrated for typical mining operations by using machines such as Tunnel Boring Machines (TBM), Continuous Miners (CM), Marietta borer miners and longwall drum shearers. The general approach to modeling and the available models are discussed and some examples of these models are presented. The comparison between the estimated and achieved performance, as well as the degree of improvement in the performance due to balancing and modification in cutterhead design are also discussed.

Jan 1, 2000

By J Taylor, L Richards, M McKenzie

When a collapse in its services shaft caused rapid gas build up and its premature closure in. 1951, the Blackwater Mine at Wiauta was in full production with significant ore reserves yet to be mined. A total of nearly 23 tonnes of gold was produced from the mine during its 44 year life. It was New ZealandÆs deepest underground mine, producing gold from an extensive sub-vertical mineralised quartz reef that averaged 0.6 m in width. Mining was by stoping between adits and short shafts, latterly with the main mine access through the 840 m deep Prohibition shaft. Macraes Mining Company Ltd are presently investigating the possibility of reopening the mine. This paper outlines a preliminary assessment of the main geotechnical factors for achieving the reopening, using recent exploration and old mine information. The greywacke host rock mass in the vicinity of the quartz reef has been evaluated using both these sources, and the paper discusses how the geological structure, intact and rock mass strengths, the rock mass defects, in situ stresses, and groundwater inflows may effect the reopening and support of the prohibition shaft, the excavation methods and support for a new supplementary shaft, and the likely excavation and support requirements for working adits and stopes in the rejuvenated mine.

Jan 1, 1996

By X. Shi

This paper presents design and implementation details of a fuzzy-behavior-based controller for an automated excavator. The robotic excavator is equipped with sensors, actuators and an embedded control system. The excavator controller uses neural-networks to interpret forces and torques gathered during the excavation process from bucket-mounted force sensors. Implementation details card experimental results using the fuzzy-behavior-based excavation controller are given for several excavation tasks. These excavation tasks demonstrate some of the complex skills that are essential for an autonomous mining-excavator controller.

Jan 1, 1997