Search Documents

By Charles A. Maliszewski, James M. Galvin, Gerhard Urschitz

With obvious signs of deterioration, the double track, historically registered Bergen Tunnels as part of the commuter rail system in New Jersey waited for rehabilitation for a long time. Serious water in filtration not only caused operational and safety hazards for the electrified rail line but also deteriorated and structurally compromised the tunnel lining. An innovative rehabilitation program was developed to enlarge the tunnel and to provide a new waterproofing system and final lining. For the rock excavation and support New Austrian Tunneling Method (NATM) principles were utilized, while water tightness was achieved by installing a PVC membrane waterproofing system followed by a reinforced cast-in-place final lining. Experienced on-site supervision generated additional savings during construction by streamlining support elements based on geologic conditions encountered.

Jan 1, 2003

By C. E. Shoenfelt

The year 1939 witnessed the rapid development of several of the more important Rocky Mountain oil and gas areas and the discovery of new oil and gas fields. As a further result of an active year, many oil fields had their productive limits greatly extended or responded to deeper drilling with oil production in lower horizons. In Colorado there was a substantial increase in refinery capacity, with three new units constructed. Its contribution to the crude-oil supply was an important extension of the producing area of a Western Slope field and a deeper oil-producing horizon in an old field east of the Front Range. Occurrences of gas were reported in two wells in northwestern Colorado, but severe winter weather prevented tests and the value of these discoveries cannot be determined at this time. Montana's northern fields were extended and a number of record wells were completed. The North Cut Bank area gives promise of wide expansion in 1940. The gas-producing area of Wyoming's Elk Basin field was extended into Montana on the north plunge of the anticline. The most important developments in Wyoming oil fields in 1939 were extensions to the producing area of Lance Creek and the discovery of a deeper pay in the Tensleep formation at Wertz dome. A new gas field at Horn Valley in the south central part of the state was the only new field discovered, but wildcatting was at low ebb in Wyoming in 1939. Colorado In Colorado, the year 1939 saw the completion of several interesting tests, but largely with negative results. Oil was discovered, however, in a deeper sand in the old Fort Collins field and the productive area of the Wilson Creek field was extended. Gas had been noted in two Western Slope wells, at Yellowjacket-Buford and at Trull, but their volumes had not been determined at the end of the year. Of principal interest, however, were the failures, descriptions of which will be given presently. One of these established a new depth record for Colorado.

Jan 1, 1940

By C. E. Shoenfelt

The year 1939 witnessed the rapid development of several of the more important Rocky Mountain oil and gas areas and the discovery of new oil and gas fields. As a further result of an active year, many oil fields had their productive limits greatly extended or responded to deeper drilling with oil production in lower horizons. In Colorado there was a substantial increase in refinery capacity, with three new units constructed. Its contribution to the crude-oil supply was an important extension of the producing area of a Western Slope field and a deeper oil-producing horizon in an old field east of the Front Range. Occurrences of gas were reported in two wells in northwestern Colorado, but severe winter weather prevented tests and the value of these discoveries cannot be determined at this time. Montana's northern fields were extended and a number of record wells were completed. The North Cut Bank area gives promise of wide expansion in 1940. The gas-producing area of Wyoming's Elk Basin field was extended into Montana on the north plunge of the anticline. The most important developments in Wyoming oil fields in 1939 were extensions to the producing area of Lance Creek and the discovery of a deeper pay in the Tensleep formation at Wertz dome. A new gas field at Horn Valley in the south central part of the state was the only new field discovered, but wildcatting was at low ebb in Wyoming in 1939. Colorado In Colorado, the year 1939 saw the completion of several interesting tests, but largely with negative results. Oil was discovered, however, in a deeper sand in the old Fort Collins field and the productive area of the Wilson Creek field was extended. Gas had been noted in two Western Slope wells, at Yellowjacket-Buford and at Trull, but their volumes had not been determined at the end of the year. Of principal interest, however, were the failures, descriptions of which will be given presently. One of these established a new depth record for Colorado.

Jan 1, 1940

By A Hewitt

Portland cement is the chief binding ingredient in mine backfill. In the presence of water, the chemical compounds within portland cement hydrate causing hardening and strength gain. During hydration, heat is generated. In certain cases, hydration heat may be produced significantly faster than it can be dissipated, which can create high temperatures in the underground environment. This paper presents the results of a series of investigations aimed at quantifying the heat generated by cemented backfill during hydration. Scaled stope models, instrumented with thermistors, were used in the investigation. Heat transfer to the hanging wall, orebody, footwall and cross-cut and production drifts was assessed during the backfill curing process and relationships between cement content, cure time, and heat generation were developed. The results of this work will assist mine operators in predicting the heat generated by cemented backfill and provide the necessary information to implement effective engineering control of heat in the underground environment.

Jan 1, 2005

By J. D. Miller, J. E. Sepulveda

Tar sand deposits in the state of Utah contain more than 25 billion bbl of in-place bitumen. Although 30 times smaller than the well-known Athabasca tar sands, Utah tar sands do represent a significant domestic energy resource comparable to the national crude oil reserves (31.3 billion bbl). Based upon a detailed analysis of the physical and chemical properties of both the bitumen and the sand, a hot-water separation process for Utah tar sands is currently being developed in our laboratories at the University of Utah. This process involves intense agitation of the tar sand in a hot caustic solution and subsequent separation of the bitumen by a modified froth flotation technique. Experimental results with an Asphalt Ridge, Utah, tar sand sample indicated that percent solids and caustic concentration were the two most important variables controlling the performance of the digestion stage. These variables were identified by means of an experimental factorial design, in which coefficients of separation greater than 0.90 were realized. Although preliminary in nature, the experimental evidence' gathered in this investigation seems to indicate that a hot-water separation process for Utah tar sands would allow for the efficient utilization of this important energy resource. The projected increase in the ever-widening gap between the domestic energy demand and the domestic energy supply for the next few years has motivated renewed interest in energy sources other than petroleum, such as tar sands, oil shale and coal. Although a number of research programs on the exploitation of national coal and oil shale resources have already been completed, very few programs have been initiated on the processing of tar sand resources in the United States. In recognition of their significance as a domestic energy resource, investigators at the University of Utah have designed an extensive research program on Utah tar sands. An important phase of this program, and the main subject of this publication, is the development of a hot-water process for the recovery of bitumen from Utah tar sands, as a preliminary step toward the production of synthetic fuels and petrochemicals. The term "tar sand" refers to a consolidated mixture of bitumen (tar) and sand. The sand in tar sand is mostly a-quartz as determined from X-ray diffraction patterns. Alternate names for "tar sands" are "oil sands" and "bituminous sands." The latter is technically correct and in that sense provides an adequate description. Tar sand deposits occur throughout the world, often in the same geographical areas as petroleum deposits. Significantly large tar sand deposits have been identified and mapped in Canada, Venezuela and, the United States. By far, the largest deposit is the Athabasca tar sands in the Province of Alberta, Canada. According to the Alberta Energy Resources Conservation Board (AERCB),2,3 proved reserves of crude in-place bitumen in the Athabasca region amount to almost 900 billion bbl. To date, this is the only tar sand deposit in the world being mined and processed for the recovery of petroleum products. Great Canadian Oil Sands, Ltd. (GCOS) produces 20 million bbl of synthetic crude oil per year. Another plant being constructed by Syncrude Canada, Ltd. is expected to produce in excess of 40 million bbl of synthetic crude oil per year. According to the Utah Geological and Mineral Survey (UGMS), tar sand deposits in the state of Utah contain more than 25 billion bbl of bitumen in place, which represent almost 95% of the total mapped resources in the United States.4 The extent of Utah tar sand reserves seems small compared to the enormous potential of Canadian tar sands. Nevertheless, Utah tar sand reserves do represent a significant energy resource comparable to the United States crude oil proved reserves of 31.3 billion bbl in 1976.5 Tar sands in Utah occur in 51 deposits along the eastern side of the state.4 However, only six out of these 51 deposits are worthy of any practical consideration (Fig. 1). As indicated in Table 1, Tar Sand Triangle is the largest deposit in the state and contains about half of the total mapped resources. Information regarding the grade or bitumen content of Utah deposits is still very limited. The bitumen content varies significantly from deposit to deposit, as well as within a given deposit. In any event, the information available6-8 seems to indicate that Utah deposits are not as rich in bitumen as the vast Canadian deposits which average 12 to 13% by weight.9 Although many occurrences of bitumen saturation up to 17% by weight have been detected in the northeastern part of the state (Asphalt Ridge and P. R. Spring), the average for reserves in Utah may well be less than 10% by weight. Separation Technology As in any other mining problem, there are two basic approaches to the recovery of bitumen from tar sands. In one

Jan 1, 1979

By R. B. Schluter, M. M. Fine

A process for winning copper from pelletized chalcocite concentrate without matte smelting and converting is under development at the Twin Cities Metallurgy Research Center of the U.S. Bureau of Mines. The new procedure includes a two-stage fluid-bed treatment in which the pelletized concentrate with 33% Cu and 7% S is first desulfurized to about 0.5% S in an oxidizing atmosphere, and then metallized by reduction with hydrogen. The reduced product is melted with flux to separate metallic copper from the gangue. The metal must be refined to remove residual sulfur and iron. The pelletizing of the fine concentrate into mini-pellets prior to fluid-bed treatment is an important feature of the process, because it permits shorter reaction time, decreases dusting, and facilitates subsequent processing.

Jan 1, 1972

By C. J. Bise, E. K. Albert

Mathematical modeling and computer simulation are the two primary techniques used for production analysis of underground coal mine layouts. Oftentimes, however, the selection between these two techniques is not based on an awareness of the level of effort needed for input formulation versus the suitability of the desired output. This paper will review mathematical modeling and two of the more prominent simulators (Virginia Tech's FACESIM and Penn State's UGMHS) used in underground coal mine production analysis. A hypothetical section will be analyzed by these programs and, based on the results of the aforementioned study, their advantages and disadvantages will be discussed.

Jan 1, 1985

By Stevens P

The Isa Mine of Mount Isa Mines Limited currently produces 5.4 million tonnes of copper ore and 3.3 million tonnes of silver, lead and zinc ore annually. Of this, 5.1 million tonnes of copper ore and 2.2 million tonnes of silver-lead-zinc ore is produced by sublevel open stoping. This paper summarises the capabilities, operating practices and problems encountered with current production drilling practices used to drill sublevel open stopes at Mount Isa.

Jan 1, 1982

By R. O. Kneisley

This U.S. Bureau of Mines report summarizes a study of large-scale strata response to longwall mining at a western U.S. coal mine. This study utilized surface and subsurface measurements, geologic mapping, in situ stress measurements, and pressure cell readings to characterize strata behavior. Preliminary analysis of surface subsidence and time-domain reflectometry (TDR) was used to determine a suggested main roof caving sequence. Coal ejected from the face apparently resulted from brittle failures that occurred because of lack of significant yield zone development. The combination of a strong coal with pronounced directional behavior, low overburden pressures, a good caving roof, and a high-production environment that minimized time-dependent loading apparently reduced yielding of the longwall face. The panel 1 headgate-entry design appears adequate; however, the abutment pillar and adjacent panel tailgate rib are highly stressed and may contribute to problems during second panel mining. The small chain pillar yielded after passage of the face, but the pillar width may be near maximum since evidence of a stressed core exists.

Jan 1, 2010

By Herbert H. Einstein

Rock mass deformability is commonly predicted using correlations with RQD or other indices of rock mass quality, or by extrapolation from large in-situ tests. Based on the probabilistic description of rock masses empirically developed in Part I a new approach was attempted in modeling for predictions of deformability. This approach decomposes the rock mass into spatially variable joints described by probability distributions, and intact rock blocks. Stiffnesses and elastic parameters are associated with the joints and intact blocks respectively, and deformations built up by adding the contributions of each. This model allows relaxation of many of the simplistic geometric assumptions which constrain parallel attempts to model deformation in rock masses. The model has been applied to four standard cases in order to test its results against previously existing models, and to check whether it replicates empirical correlations. When joints are taken as parallel, common empirical correlations are closely approximated by the model output. However, the closeness to empirical correlation breaks down when variability of the jointing geometry is increased.

Jan 1, 1979

By Jamal Rostami, Jürgen Schmitt, Rohola Hasanpour

"Double Shield TBMs can be used in fast track projects for accelerated completion where there is limited information available on ground conditions and there are possibilities of encountering weak ground and shear zones. As such, the shielded TBMs are the primary choice of the machines in long tunnels, but face the possibility of entrapment in squeezing ground, which entails long delays and major risks. This paper examines the possibility of using ground improvement methods to increase ground strength, and thus, increase the capability of the machines to cope with squeezing ground conditions. In this study, 3D finite difference simulation of a shielded TBM in squeezing ground was performed to estimate the operational parameters including required thrust to get a machine out of an entrapment. This analysis was also used to evaluate the possibility of preventing machine jamming by the implementation of pre-excavation ground improvement to increase the strength of the ground. INTRODUCTION In order to face adverse tunneling conditions especially using a shielded TBM in squeezing ground, new shield designs, with extra thrust and torque, step shield geometry with reduced shield diameter from front to the back, and conical shape shields have been used. In addition, many of the new machines have the capability to implement ground improvement at distances up to 50 m ahead of the face in order to reinforce the ground and further increase in their chances to cope with squeezing ground conditions. While these features have been added to the machine, there has not been a thorough evaluation of their impact on improving the chances to avoid machine jamming in weak rocks at high depth, which is conducive to rapid convergence of the ground."

Jan 1, 2016

By Wallace W. Key

The California pesticide industry in 1962 consumed about 30,000 tons of clay, talc, limestone, diatomite, sulfur, and other minerals as fillers (carriers and diluents) in pesticide formulation. This was 10 percent of the U.S. filler requirement for pesticides. About two-thirds of the California total was supplied by a few local mineral producers; the remainder came mainly from Florida, Georgia, and Wyoming. The objectives of this report are to provide data on quantities, sources, specifications, and market conditions for minerals used as fillers by California pesticide formulators. The study disclosed that specifications for mineral fillers have become more rigid and formulators have become more numerous in recent years. During 1962 over 1,200 firms registered 16,000 pesticide products with the Bureau of Chemistry in California. Factors which will tend to diminish future need for mineral fillers include the trend toward greater use of organic sprays rather than dusts and further development of biological controls, such as the development of sterile insect strains.

Jan 1, 1965

By H. L. Gilbert, C. T. Anderson, W. J. Kroll

In a previous paper,' the use of a split graphite tube resistor as a heater element for high-temperature furnaces has been described. The principal advantages of this type of construction are: I. The quadruple resistance or voltage compared with the top-bottom clamp resistor furnace. 2. Free expansion of the resistor. 3. The ease of protection from oxidation by air. 4. The firmness by which it may be held in the compact split clamp. This construction appeared to be well adapted for the fusion of high melting metals which require fusion in a vacuum. Zirconium metal had previously been melted at the Albany Laboratory of the Bureau of Mines in a vacuum arc furnace on a water-cooled plate, using a movable tungsten top electrode.% When larger furnace capacities were desired, this type of construction proved to have its limitations as the largest tungsten rods available were about 7/8 in. in diameter. The supply of direct current of high amperage for producing the desired arc characteristics was also not available. Considerable difficulty was also found in compensating the atmospheric pressure on the flcxible tubing of the movable electrodc, at the same time keeping its movement sufficiently free to enable the striking of an arc on any part of the metal briquet. Among the various materials used for the electrodes in conducting experiments in the vacuum arc furnace was graphite. It was found that zirconium fused in a graphite cup with a carbon arc was contaminated to only 0.2 pct carbon. It was therefore decsed to melt zirconium directly in graphite crucibles. A high-frequency furnace was first used in the attempt to melt the zirconium in graphite crucibles. The high-frequency heating coil was placed outside a silica tube which was evacuated by means of an oil diffusion pump backed up by a mechanical pump. The graphite crucible was thoroughly degassed at 19oo"C before use. Considerable difficulty was experienced in operating at such temperatures in vacuo because, as shown by Zintl,3 carbon vapor formed and reacted with silica accortling to the reaction: SiO² + C = SiO + CO. The silicon monoxide which is volatile at these high temperatures reacted with the zirconium, thereby contaminating it with silicon and oxygen. The presence of carbon monoxide was detected by means of a gas discharge tube placed in the vacuum system as indicated by the pale blue glow of the tube as soon as carbon vapor started to react with the hot silica. The reaction between the carbon vapor and hot silica was avoided by the use of split cylindrical molybdenum shields which were inserted between the graphite crucible

Jan 1, 1949

By Edward Hall Smith

The E1 Indio Mine is located in the Andes mountains about 180 kilometers East of La Serena, capital of the Fourth Region of Chile. It is reached by an international highway running up the Elqui Valley as far as Juntas from where the last 42 kilometers is on a road constructed by the Company. The plant is located at 3.900 meters above sea level among extremely rugged terrain with nearby mountains rising about 5.500 meters. Climatic conditions at these altitudes are severe with winter temperatures down to -20°C. Snow storms lasting several days and leaving up to two meters of snow have been experienced, while fierce winds are corm=.

Jan 1, 1984

By G. S. Rice

The recommendations of the Bureau of Mines on rock dusting practices are embodied, except in a few details, in the Recommended American Practice for Rock-Dusting Coal Mines to Prevent Coal-Dust Explosions, approved by the American Engineering Standards Committee. December 30, 1925. It is specified that the dust to be used is of a elm that all will pass through a sieve having 20 meshes per linear inch and that 50 per cent or more will pass through a sieve having 200 meshes per linear inch. Thus the coarsest size of dust and the minimum proportion of fine dust are specified, but the specification does not indicate whether a larger proportion of fine dust would be desirable. There have been advocates of the use of that size of rock dust of which the particles would all approach 200-mesh in fineness. Explosion tests were made in the Experimental mine in the earlier period of testing which indicated that the finer rock dust is somewhat more effective under test conditions, but not sufficiently so to Justify the cost of finer grinding of the dust; also there are some disadvantages of finer dust described hereafter.

Jan 1, 1930

By Kosta Fytas, Nour-Eddine Chaouai

"Selection of the appropriate kriging plan during indicator kriging estimations is of a paramount importance to the precision of ore reserve estimation. However, very little is known on the sensitivy of indicator kriging results when changing the kriging plan parameters (mainly search distance and number of samples). This paper evaluates the effect of the search distance and number of samples on indicator kriging results using a gold deposit as a case study.IntroductionBlock estimation using kriging is based on the autocorrelation function (variogram) on one hand and on the kriging plan on the other. As far as the variogram is concerned it is more or less subjectively adjusted and this is reflected on its parameters (range, sill, nugget effect and anisotropy). The effect of a poor estimation of these parameters on the kriging variance of ordinary kriging has been proven very important (Brooker, 1986). Choosing a kriging plan is generally a difficult matter depending on the estimation type (global or local). Generally there is not a unique kriging plan be cause there is not a unique structural analysis (variogram). There are no rules or dogmas in choosing a kriging plan but it is rather a function of the sampling pattern (David, 1982).Structural analysis requires the hypothesis of quasistationarity but very often either the data available within the zone of quasi-stationarity are too many so that the search distance is reduced during kriging or the data are too few to satisfy a stationary kriging system (Journel and Huijbregts 1978). As a rule, the larger the neighbourhood, the more precise the estimates should be , but for large neighbourhoods the hypothesis of stationarity does not always hold (Rivoirard 1987; Armstrong and Champigny 1989)."

Jan 1, 1991

By J. H. Crocket, J. Andy Fyon

"All gold deposits within the Tisdale Group are spatially associated with carbonate alteration zones; however, not all carbonate alteration zones are host to gold mineralization.Within the komatiitic and magnesium tholeiitic volcanic rocks at the base of the Tisdale Group, discordant and stratabound carbonate alteration zones occur throughout. The alteration zones consist of a ferroan dolomite - quartz inner assemblage which is enveloped by calcite-quartz and an outer chlorite-rich subzone. Factors which control the distribution of carbonate alteration include joint systems, flow contacts, synvolcanic faults and bulk composition of the host rock.Two environments of carbonate alteration can be recognized: 1) The subsea-floor alteration zones developed within the volcanic rock succession where hydrothermal fluids did not discharge directly onto the sea floor. Insignificant gold production has come from this alteration environment. 2) Seafloor zones, which represent points of hydrothermal fluid discharge into the hydrosphere, are spatially associated with felsic volcanic rock complexes and are host to syngenetic, auriferous cherty dolomite.Carbonatized, magnesium tholeiitic basalts, which are host to the auriferous, cherty dolomite, are enriched in antimony (>0.35 ppm), boron (>30 ppm), gold (>5 ppb) and lithium (> 35 ppm), but are depleted in copper ( < 70 ppm), with respect to carbonatized basalts not associated with gold. Orerelated, altered komatiitic flows can be screened using gold (>5 ppb), lead(> 10 ppm), arsenic(> 70 ppm) and antimony (>1 ppm).The habit, petrographic characteristics and certain geochemical characteristics of the altered volcanic rocks suggest that the hydrothermal fluid was of sea-water origin."

Jan 1, 1982

By P. C. Lightfoot, J. M. Duke, A. J. Naldrett

"The segregation of magmatic sulphides from mafic and ultramafic silicate magmas, in many circumstances, leaves the magma with a lower-than-normal Ni/MgO ratio, which is characteristic of both lavas erupted from the magma chamber and olivine crystallizing within it. Two end members of the segregation process are discussed; i) batch segregation and ii) fractional segregation.In the former, the critical factor is the magma/sulphide ratio. Computer modelling suggests that where this ratio has been less than 1000, the magma will be recognizable as anomalously low in Ni, due to sulphide segregation, and thus a good target for exploration. In fractional segregation, the critical factors are the proportion of sulphide to silicate being segregated and the degree of fractionation.Samples believed to represent the liquid portion of komatiitic lava f lows from a series of unmineralized sequences in the Abitibi greenstone belt, Canada. Belingwe belt, Zimbabwe, and Barberton Mountainland, South Africa coincide with the sulphide-free fractionation model. They are in marked contrast to samples from the ore-bearing districts of Kambalda and Scotia. Western Australia in which distinct Ni depletion, corresponding to fractionation of olivine plus sulphide in a ratio of between 100 and 200:1 is recognizable. Ni-depleted olivines also mark the sulphide-bearing Dumont intrusion of the Abitibi belt.The Moxie intrusion of northern Maine has distinctly Nidepleted olivines, as does the nearby and petrologically related Katahdin body. In both of these intrusions, the composition of the olivine allows reasonable predictions to be made of the Ni tenors of sulphide showings within them. At Katahdin, the Ni depletion is so widespread that little hope is help out for the presence of economic concentrations of sulphide. At Moxie. the olivine compositions suggest that the best chance of economic sulphides lies in the southern lobe of the intrusion.Ni-depleted olivines also characterize certain rock units within intrusions of the Insizwa complex, Transkei, Southern Africa. Many millions of tonnes of Ni have apparently been removed by sulphides from these rock units, many more than are contained within the single mineralized occurrence so far identified at Waterfall Gorge."

Jan 1, 1984

By Raymond J. Poletto

This paper describes the special problems that occur with the construction of diaphragm walls and discusses the lessons learned during the repairs of structural walls. Although diaphragm or slurry wall technology and equipment has vastly improved since its development in the late 1950?s, significant problems still occur. Key issues are repairs related to panel joints between wall panels, concrete defects associated with tremie concrete problems, leaks and other defects at tieback reservations or inserts, wall leaks within the plane of the wall and surface repairs. The paper supports the position that diaphragm walls are relatively watertight when properly constructed, but cautions that it is necessary to address potential problems in the design stage and allow for flexibility in construction so that the problems that occur can be corrected once encountered. Due to the fast track nature of most projects the time available for design, detailing and construction is limited. As a result, insufficient attention to detail by any of the responsible parties can lead to imperfections and defects in the wall. The authors describe the nature of these problems and their potential resolution based on ?lessons learned.? The timely response to wall problems is essential to the successful completion of a diaphragm wall project. Appropriate repairs have resulted in largely successful jobs starting with the World Trade Center in New York City. The authors? total 80 years of experience as the engineer of record and designer, inspector and contractor?s representative for the diaphragm wall results in a unique insight to deal with these problems.

Jan 1, 2011

By Nathaniel Arbiter

The increasing size of flotation cells as the use of flotation has increased is traced from the first United States application of the process in Montana in 1911 through the following eight decades, using data from the Taggart handbooks (1927) and (1945), from the SME Handbook (1984), and from recent manufacturers&apos; catalogues and other sources for the 1980s and 1990s. With the earliest mechanical cells less than 1 m3 (359) in volume and the largest now available at 200 m3 (7,000ft3), three requirements are necessary: 1) demonstration of advantages in replacing smaller volume by larger volume cells; 2) estimating power requirements, impeller dimensions, and operating rpm by correlation equations; 3) considering effects of using larger cells, in necessarily much shorter rows, on process kinetics. The resulting seven tables that address these problems are presented, and their implications discussed.

Jan 1, 1999