Search Documents

By Frederico Muylaert Margem, Jarbas Bravo Neto, Sergio Neves Monteiro

"The mechanical behavior and the fracture characteristics of composites with DGEBA/TETA epoxy matrix reinforced with up to 40% in volume of continuous and thinner ramie fibers were evaluated by tensile tests. Specimens with selected thin fibers aligned along the tensile axis were room temperature tested to rupture. The fracture surface was analyzed by scanning electron microscopy. The results showed significant increase in both the ultimate tensile strength and the elastic modulus. The fracture analysis indicated the possible mechanism for the fiber/matrix interaction, which could be responsible for the composite performance.IntroductionThe fiber reinforced polymer composite emerged in the middle of last century as a versatile engineering material for applications requiring mechanical resistance in association with lightness. Its most commonly used example is ""fiberglass'', i.e., a thermoset polymer matrix composite reinforced with glass fiber. Indeed, ""fiberglass"" has a specific strength of the order of 500 MPa.cm3/g, which is the double of the strongest steels like the maraging. This motivated, at earlier times, ""fiberglass"" to replace many conventional materials including wood and natural fiber composites. Today, ""fiberglass"" has a wide range of uses from aerospace systems and appliances to sport and leisure components. However, its fabrication as well as those of any synthetic fiber such as carbon and aramid composites, requires a relatively large amount of energy. Presently, a growing concern exists regarding the consequences to the environmental by gases like C02 associated with both the energy consumption and the processing of synthetic fibers and their composites. These gases are well known responsible for global warming [1]."

Jan 1, 2011

By B. Mishra

The major waste product of the alkaline extraction of alumina from bauxite [Bayer Process] is known as red-mud. Approximately, a ton of red-mud is produced for every two tons of bauxite that is mined. The red-mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that over 90 wt. pct. alumina can be recovered from red-mud by soda-ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of over 94 pct. At this stage, the product could be charged through the tuyeres in an iron blast furnace or smelted to produce pig iron. The mineralogical characteristics of the reduced product are not amenable to magnetic separation for iron recovery. The problems associated with the use of reduced red-mud as an alternative to direct-reduced iron [DRI] has also been discussed. Special attention has been paid to lower the alkali content of the reduced material. If smelted, the concentration of titanium oxide in the slag will be significantly high justifying its recovery by an acid-leach process. This paper describes the successful efforts of iron and alumina recovery.

Jan 1, 2000

By Zhucheng Huang, Ronghai ZHONG, Tao Jiang, Jun ZOU

The method of reduction roasting and magnetic separation of low-grade, micro- fine disseminated refractory iron ore following granulation with coal produced unexpected success. Pellets of iron ore with diameter between 3 and 8mm were granulated with coal, bentonite and water. The raw pellets and reduction products were analyzed by scanning electron microscopy and x-ray diffraction. Results show uniformly distributed coal powders inside the pellets improved the kinetics of the reduction process and accelerated the reduction rate. Reduction time was higher at temperatures below 890℃, which resulted in the formation of substantial amounts of fayalite. When temperature was increased, micro- fine hematite was then quickly reduced to iron metal and the amount of fayalite decreased sharply. When pellets were reduced at 950℃ for 25min, reduction products with 56.73% metallization rate were obtained. After grinding and magnetic separation, a concentrate with 72.18% Fetot was obtained.

Jan 1, 2015

By W. G. Davenport

Smelting oxidizes Cu-Fe-S concentrate to matte. Converting oxidizes this matte to metallic copper. Smelting and converting are, therefore, part of the same oxidation process. It would seem natural, then, that smelting and converting should be combined to produce metallic copper in one step. This would: (a) maximize S02 capture by restricting S02 emission to a single, continuous source (b) minimize industrial oxygen and fuel requirements (c) minimize cost. This chapter discusses one step, direct-to-copper flash smelting as it is practiced in 2000. It then uses. the matrices of this book to determine: (a) the industrial oxygen and oil requirements of direct-to copper flash smelting (b) the distribution of Cu between metal and slag during direct-to-copper flash smelting. It concludes that direct-to-copper flash smelting: (a) captures?S02 efficiently from its single continuous stream of SO2 off gas (b) minimizes oxygen/oil consumption but: (c) sends -114 of its Cu-in-feed to slag.

Jan 1, 2001

By D. C. Cupertino

Oxime based solvent extraction provides the user with a selective concentration process for copper prior to electrowinning. The selectivity required is largely for copper(II) over iron(III) and this is achieved by the preferential formation of the square planar copper-oxime complex in the organic phase. The copper/iron selectivity of oximes can however, be altered by modifiers or other types of oximes and may be enhanced in the presence of certain esters. Whilst the oxime based SX processes is important for operations leaching copper from laterite ores, the high selectivity will also be significant in processing streams arising from other leaching regimes which are currently under development, for example leaching of sulfide mineral ores. This paper presents some initial results using Molecular Modelling techniques to further our understanding of the nature of the copper/iron-oxime complexation processes together with some plant studies undertaken at a number of different mine sites investigating selectivity, and other properties, for some modified reagents. Some studies of the interfacial properties of the these systems are reported to explain in part the practical observations.

Jan 1, 1999

By J. F. White

An experimental study was undertaken to evaluate the feasibility of a selective chloridizing roasting pre?treatment process for the elimination of impurities from zinc feed?stocks prior to recovering zinc by conventional unit operations. In this investigation, a number of chemistries that might serve as a basis for such a pre? treatment process were examined. A variety of chloridizing agents were admixed with EAF dust to promote the selective removal of lead and cadmium by the formation of volatile metal chlorides, he results of the experimentation firmly establish that selective chloridizing roasting is a technically feasible means of eliminating lead and cadmium from EAF dust. Excellent extraction efficiencies were accomplished with a number of chloride additives; as high as 98 percent lead extraction and 88 percent cadmium extraction were attained with minimal zinc losses, Continuous pilot?scale tests reinforced the trends established by laboratory?scale experimentation, Attempts of chlorine elimination using pyrohydrolysis were less successful. The extent of chlorine elimination was found to be highly dependent upon EAF dust sample type and treatment temperature.

Jan 1, 1996

By D. W. Collins

Several organic and inorganic substances are widely used to control deposit structure and morphology during the electroprocessing of copper. Methods for monitoring the levels of thiourea, glue and guar gum during electrorefining and electrowinning have been successfully developed under the trade names of Reatrol and CollaMat. Other instrumental methods have been developed for additives and decomposition products associated with the electroplating of copper and other metals. Generally, these methods have been found to be either insufficiently sensitive or lacking in the desired selectivity for some or all of the additives. These procedures have mostly employed DC techniques; i.e., cyclic voltammetry, Tafel analysis, etc. In this work, chronopotentiometry (CP) and AC voltammetry were used to examine the interaction of glue, guar gum, thiourea and chloride during the electroplating of copper onto a platinum electrode. In addition, the interactions between the additives have been explored. It was found that glue in pure electrolyte (H2S04 and CuS04 only) had no effect on the chronopotentiogram. Glue was only active if chloride ions were present. The addition of thiourea resulted in several different chronopotentiograms depending on the presence of either chloride or chloride and glue. Thiourea used in conjunction with glue and chloride showed a significant increase in the polarization during copper deposition when compared to the electrolyte containing only glue and chloride. The use of a modified channel electrode further increased the sensitivity of CP. The use of AC voltammetry was explored as a technique to monitor some of the additives. AC voltammograms have more spectral detail then their DC counterparts and it is possible to monitor some of the additives at very low concentrations with AC techniques.

Jan 1, 1999

By H. Kandemir

An experimental study of the bacterial oxidation of naturally occurring high-purity sulphide minerals (FeS2, Fe1-xS, Cu5FeS4, ZnS) is presented using a mesophilic strain of T. ferrooxidans. As well as metal analyses and solution pH, partitioning of sulphide sulphur into elemental sulphur and sulphate has been monitored as a function of leach time. Partially oxidized sulphide substrates have been characterized, at regular time intervals, by X-ray diffraction methods and extracellular organic compounds reporting into leach solution .have been identified by thin layer -chromatography.

Jan 1, 1985

By Pertti Koukkari

The novel Jarogain process combines treatment of the jarosite residue of zinc manufacturing and processing of arc furnace dust from steelmaking to a holistic recovery technology. The new hydrometallurgical approach is targeted to recover the major constituents (Fe, Zn, Pb) as well as valuable components such as Ag, Au, In and Ga from the jarosite-dust mixture as reusable concentrates. The fractionation process proposed by VTT and Aalto University takes advantage of jarosite being readily fine powder and directly available for wet chemical processing. Jarogain process provides an energy efficient opportunity for jarosite utilization as value added products. The experimental proof-of-concept of key stages of the process will be outlined with a comparison of available pyrometallurgical treatments of jarosite waste. The techno-economical assessment is based on estimated investment and variable production cost using the discounted cash flow (DCF) analysis.

By Jianhong Dong, Min Chen, Cuihuan Huang, Bo Li, Nan Wang

"Scale layer can be formed on the slab surface in the areas of secondary cooling and strand discharge during continuous casting process. From 1000 °C -1200 °C, the influence of steel composition on the stable oxide phases inside scale layer, particularly the types of alloying elements including aluminum, silicon and chromium, is investigated under different partial pressures of water vapor by the calculated predominance diagrams of iron oxide as well as its intermediate compounds formed with other metal oxides, and the stable oxide phase composition within scale layer under the working condition of secondary cooling is discussed. At lower partial pressure of water vapor, only a iron spinel (or ferrosilicate) phase is the stable phase with any alloying element contents in steel composition, whereas the stable phases are FeO and iron spine! (or ferrosilicate) inside the scale layer at higher partial pressures of water vapor .IntroductionOxide scale formation on the surface of cast and rolled products because of oxidation by the surrounding oxidizing atmosphere is a significant disturbance factor in steelmaking. The yield loss of iron because of scale formation is considerable during continuous casting and hot rolling process. Surface quality more often is impaired by scale property, which increasing the difficulty of quality assurance, dimensional accuracy and performance control. Furthermore, a potential source for subsequent surface cracking (hot shortness) can be caused by the enrichment of scrap residuals (Cu, As and Sn) at the steel substrate surface as a result of steel oxidation [1-2]. In flat products manufacture via thin slab casting technologies, these phenomena are particularly pronounced and require enhanced development efforts in descaling efficiency [3].Compared with the scale formation in continuous casting, the quantity of scale formed during hot rolling and reheating in the rolling mill is larger, and control of scale formation and descaling is a long-established task in hot rolling. Therefore, extensive research and development work have been carried out, including the effects of heating and rolling temperature on the thickness and microstructure of scale layer, heating time and furnace atmosphere, cooling mode, and steel composition on the scale formation, more attention has been given to the control of scale formation during reheating and hot-rolling process. On the other hand, hardly any specific efforts and countermeasures are taken in continuous casting, and very less research has been done despite the network-type crack on the as-cast strand surface caused by the subscale enrichment of scrap residuals [ 4-7]."

Jan 1, 2014

By Sui Xue

A process has been developed from laboratory-scale experiments for the aqueous processing of various lead-bearing wastes. The process exploits the limited solubility of lead in sulfate-rich solutions to effectively separate lead from other metals. The lead sulfate is then completely converted to lead carbonate using sodium carbonate and ammonium carbonate. The effectiveness of this conversion was observed to be sensitive to the solution pH and carbonate concentration. The final stage of the process uses low temperature calcination of the lead carbonate to form PbO. Yellow lead oxide (massicot) is readily formed if calcination is conducted at a temperature at or iibove 50G°C, wlule red iead oxide (iitharge) is formed at temperatures near 450°?C. A complete economical analysis of the process will be discussed.

Jan 1, 1996

By Dian Adisty, Leiv Kolbeinsen, Eli Ringdalen

In Si and FeSi production, the main Si source is SiO2, in the form of quartz. Reactions with SiO2 generate SiO-gas that further reacts with SiC to Si. During heating, quartz will transform to other SiO2 modifications with cristobalite as the stable high temperature phase. Transformation to cristobalite has been investigated and shown to be a slow process where the rate varies between the investigated quartz types. The effect of quartz versus cristobalite as SiO2 source has been studied for reaction (1) 2SiO2 + SiC = 3SiO + CO, by heating of pellets with SiO2 + SiC in Ar-gas. The reaction was faster with cristobalite than with quartz. Initial experiments indicates that this is the case only in Ar and not in CO-atmosphere The higher specific surface area of cristobalite is believed to contribute to the higher rate. The industrial consequences of the observed difference between quartz types are discussed.

Jan 1, 2014

By Pinakin C. Chaubal

Today?s steel industry is in a vibrant and resurgent mode. This transformation has been in the making for some time now. Over the last few decades, the industry was steadily transforming itself into becoming a high tech industry. New technology was adopted, efficiencies were enhanced, lean manufacturing concepts were brought in and a strong customer focus was developed. Today?s mills employ sophisticated instrumentation, computerized monitoring, on-line smart systems etc. driving processes that are producing at rates of many tons/minute. All this is not possible without judiciously using the latest available technologies in various fields and developing a more sophisticated work force. Prof. Sohn has been a pioneer in driving the concept of process engineering in process metallurgy. In this paper the focus is on some aspects of process engineering ? primarily process modeling - as applied to iron and steelmaking processes. Examples are shown to demonstrate how problems have been addressed. Some thoughts on future directions are presented.

Jan 1, 2006

By Sung-Mo Jung

Experiments were carried out on a system with artificially prepared slags in a graphite crucible, in order to examine the possibility of recycling BOF slags produced in the steelmaking process. More than 80% of FeO and P2O5 was reduced within 20 minutes and the FeO reduction rate was greater than that of P2O5. P2O5 reduction began after more than 60% of FeO was reduced. Increasing slag basicity enhanced the reduction of FeO and P2O5. Temperature also improved slag reduction. The overall reduction rate was controlled by the chemical reaction at the slag/carbon interface. The reduction rates of FeO and P2O5 were second and first order with respect to their respective contents. Most of the reduced phosphorous is believed to vaporize in the form of P2 gas.

Jan 1, 2006

By Rollie E. Dutton, David A. Stubbs

"A sensor has been developed and tested that is capable of emitting and receiving ultrasonic energy at temperatures exceeding 900°C and pressures above 150 MPa. The sensor works with standard ultrasonic pulser-receivers and has demonstrated the capability of measuring workpiece deformation during hot isostatic pressing (HIP). Details of the sensor design, performance, and coupling of the ultrasound to the workpiece are described. Ultrasonic data acquired by the sensor, in situ, during HIP runs and at elevated temperatures in air are presented.INTRODUCTIONHigh temperature structural components, such as structural castings for jet engines, nickel-base superalloy turbine blades, and ceramic and metal matrix composites made from powders are often densified by hot isostatic pressing (HIP). For powder consolidification, the HIP process involves sealing the powder (and reinforcing fibers for composites) within an evacuated ""Can"" made of a material that softens at high temperatures. A hydrostatic pressure is then applied by pressurizing the inside of the HIP vessel with argon gas (up to 140 MPa). The hydrostatic pressure densities the powder through the elimination of the porosity between the powder particles.This paper presents details of the development and preliminary testing of an ultrasonic displacement sensor that can be used to monitor materials processing, in situ, at temperatures and pressures significantly higher than current ultrasonic displacement sensors. The target processing environment for this sensor is that typically found in a hot isostatic pressure (HIP) vessel, i.e., temperatures exceeding 1000°C and pressures above 138 MP a."

Jan 1, 1997

By Tianzu Yang, Weifeng Liu, Lin Chen, Deyu Wang

"Due to the gradual exhaustion of easily extractive gold ores, it is vital to make efficient use of refractory gold ores which hold 30% gold storage of the world. However, the disadvantage of current processing technologies for refractory gold ores consists of severe pollution, low gold extraction ratio, high investment, etc, thus great research interests were attracted during recent years. This article provides an overview of the distribution and categories of the refractory gold ores in the world. The state of art in processing refractory gold ores by pyrometallurgy, hydrometallurgy and biometallurgy techniques and their industrial applications are highlighted. Potential environmental conservative techniques for efficient gold extraction are also reviewed.IntroductionResources of Refractory Gold OresAs easily extractive gold ores are going to be exhausted with the large scale mining nowadays, refractory gold ores are becoming more and more important. Gold in the refractory gold ore cannot be fully extracted using conventional method (cyanidation) even with fine grinding. The amount of gold in the refractory gold ores is about 1500~2000t in China, which occupies 30~40% of the total gold storage [1]. Therefore, it is vital to make efficient use of refractory gold ores."

Jan 1, 2013

By Wei Gao, Qing-cai Liu, Cun-fang Lu, Huimin Zheng, Jian Yang, Chun-ling Yao

"Mercury in flue gas of coal-fired plants was concerned as another serious pollution when sulfur dioxide pollution was controlled now. The adsorbent made from fly ash by thermal precipitation sulfur to remove mercury in fuel gas from coal combustion plant, SEM, BET, TGA and other measurement methods were used to characterize the effect on surface morphology, sulfur distribution and specific surface. High temperature deposition furnace was applied to increase sulfur content in fly ash based adsorbents produced in lab. The study found that sulfur attached to the adsorbent surface, mesopore and microporous structure, increasing its sulfur content of adsorbent. Sulfur was filled in interspace as small molecule S2, S5, increased their surface area and enhanced their adsorption capacity. The specific surface area increased by thermal precipitation sulfur, and specific surface area which increased with increasing temperature.1. IntroductionThe mercury emission caused by human activity has accounted for 10%-30% of total mercury emission all over the world[11, and the emission from coal-fired power plant have a huge proportion of these emission caused by human activity. Active carbon microstructure and surface morphology play an important role in its adsorption capability, which offers the potential for controlling environmental pollutant, such as sewage, fuel gas, atmosphere and et al [2,31, because it is a material with high specific surface area that long been considered as an excellent adsorbent. At present, include activated carbon, fly ash, calcium-based sorbents and other novel adsorbents. The adsorption capacity and production cost were very important in the process of mercury removal by adsorbents, so the mercury removal has focus on developing adsorbents of highly-efficient. In particular, the waste of metallurgical from coal combustion and the others have a significant advantage about the cost, and they have the highly-efficient in mercury removal after modified to enhance their adsorption capacity, such as fly ash of coal-fired. Apart from specific surface area, element content, pore structure, and surface morphology of activated carbon have great effect on its adsorption ability. Compared to adsorbents without modification, active carbon impregnated with other elements, such as chlorine, sulfur, bromine and et al. had more excellent characteristics to remove specific pollutants."

Jan 1, 2011

By Jinxia Nie, Yunnen Chen, Dachao Zhang

"Rare earth resources are strategic and non-renewable resources. But disordered exploitation on rare earth metals leads to resources waste, environmental pollution and ecosystem destroyed. In this paper, soil collected from garden was cultured in thermostated incubator. Adding exogenous rare earth to the soil and the effects of recombination action of rare earth lanthanum, cerium and yttrium on soil enzymatic activities were studied. The results showed that single metal La and Ce can increase urease activity, but Y inhibits its. Coexist La/Y or La/Ce in soil inhibit the urease activity, coexist Y /Ce or coexist three metals promote its. Single metal La, Y and Ce can promote catalase activity, and that of coexist three metals. Pairwise coexist La, Y, Ce in soil inhibit catalase activity. With certain concentration of rare earth recombination action, urease activity in soil has been very significant direct proportion to ionic impulse, but catalase activity been insignificant inverse proportion to its.1. IntroductionThe increase of rare earth element content due to anthropogenic inputs frequently takes place in agro-industrial areas, leading to soil pollution episodes that may cause serious environmental problems because of their potential toxicity to microorganisms, plants, animals and human beings [ 1]. China is abundant in lanthanides resources. Rare earth metals are used in many frontier technologies such as photic devices, magnetic materials, and fine ceramics, and the amount of the rare earth metals used in these industries has been increasing. In addition to their use in industry, rare earth metals are more widely applied to cropland as microelement fertilizers due to their ability to promote growth and productivity of some crops [2]. As a result, more and more rare earth metals are moving into the ecosystems. While a permanent contamination of soils results in populations of micro-organisms with high resistance to rare earth metals, a short-term burden of contaminants at high concentrations could exert inhibitory effects on microbial carbon [3]. They accumulate in soils, bioaccumulate in crops, and enter the food chain, causing a potential problem of rare earth metals environmental pollution in China [4]. This contamination may also severely influence organisms and soil activities [5]."

Jan 1, 2011

By D. R. Spink

A partial desulfurization roasting (PDR) technique has been developed for use on zinc concentrates whereby the sulfide sulfur associated with the iron content is selectively removed over a very short residence ?time in the roaster. The resulting PDR product is then leached for the selective removal of the iron. The resulting leach restdite is an upgraded zinc sulfide concentrate which has a very low iron content. The up-graded zinc concentrate can be subjected to a conventional dead roast without formation of deleterious zinc ferrite so that hot acid leaching and jarosite (or other) iron precipitation steps are obviated. Examples are presented for the treatment of three very different types of zinc concentrates.

Jan 1, 1990

By Dilip Banerjee

"This paper discusses the Advanced Technology Program (ATP)'s support over the last decade to the development and use of process modeling as a tool to address some of the challenges faced by the U.S. metal casting industries. A particular focus will be given to highlight how process modeling can be used to improve the manufacturability of components needed for high performance and critical applications. The challenges associated with the design and production of thin-walled, cast parts with intricate and complex internal geometries will be discussed. Modeling issues associated with the control of the final grain structure in the solidified parts will also be addressed. This paper will describe the advantages of using appropriate mathematical models for designing new alloys for use in various applications.Finally, the role that ATP has played in uplifting the U.S. technological base through partnerships with industry and academia in high-risk research in order to bring to market new and improved products for the broader benefit of the nation will be discussed.ATP's BackgroundIn the 1980s, U.S. industries were losing market share to low-cost, high-quality manufacturers from Asian countries. Corporate leaders and policy makers determined that in order to sustain and grow market share, U.S. industries needed to improve their competitiveness and productivity through product and process innovation. There was evidence that companies were systematically under-investing in leading-edgetechnologies and failing to complete the development of new technologies [l]. There were also arguments in academic circles that pointed to a potential market failure in the area of early-stage technological developments. These concerns provided impetus for creation of the Advanced Technology Program (ATP) within the National Institute of Standards and Technology through the Omnibus Trade and Competitiveness Act of 1988. Through a rigorously competitive, cost-shared partnership with industry, ATP fosters the development and broad dissemination of high-risk technologies that offer the potential for significant broad-based economic benefits to the United States."

Jan 1, 2004