Search Documents

By Tangstadm Merete, Eli Ringdalen

"This paper presents an overview of results from The Norwegian Research Institution SINTEF and the Norwegian University of Science and Technology, NTNU regarding new and ongoing research in silicon production. The main studies are related to condensation of SiO gas and cavity formation. If SiO gas condensation is increased at the top of the furnace resulting in SiO content in the off-gas closer to equilibrium, the Si yield will be increased significantly. Experimental work, simulating a cavity under industrial conditions, has shown that the cavity grows downwards from one layer. Physical appearance of zones in industrial furnaces, and selected reactions in these, are discussed based on results from excavation of industrial furnaces and results from laboratory experiments. Experimental studies of reaction rates for the formation of SiO are presented. Quartz properties are demonstrated to vary between differing quartz types and the effect of this is discussed.Introduction Both the theoretical and industrial issues associated with the production of silicon are described in detail in the textbook written by Schei et al [1]. This book covers the knowledge of silicon production process up to 1998. Together with the work by Myrhaug [1] and by Aasly[2], this is the main basis for this paper. Recent and ongoing research at SINTEF and NTNU focusing on production of Si and SiO in the high temperature zone, dissociation of SiO and condensate and cavity formation will be discussed."

Jan 1, 2012

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade. The most visible technological innovation was the commissioning of the Pb-Cu smelter. Its flexibility towards very different types of feed makes it perfectly suited as main entry to the Hoboken flow sheet. A new Cu-leaching & electro winning plant and precious metals refinery make up the Precious Metals Operations (PMO) whose targets are fast throughput and maximized yields for gold, silver and the platinum group metals. The Base Metals Operations (BMO), flexibly process the by-products from the PMO, valorizing ?impurities? like indium, tellurium, selenium and others. Off gas and waste water treatments ensure compliance with strict environmental standards. Precious metals recycling is an art that goes beyond mastering a unique flow sheet. Umicore Precious Metals Refining offers a complete recycling service, taking care of sampling and assaying, metals management and logistics. The quality of this integral service is recognized through the attribution of ISO certifications for our operational activities, sampling and the environmental care. And it?s an art that follows Michelangelo?s experience: ?Art is 5% of inspiration and 95% of transpiration.?

Jan 1, 2006

By Torn H. Okabe

A fundamental study was conducted with the purpose of establishing an environmentally sound recovery process for recycling of valuable metals, by combining scraps containing such metals. As an example, direct extraction and recovery of neodymium (Nd) in magnet scraps was investigated by utilizing liquid metal as an extraction medium. It was found that liquid magnesium (Mg) is a suitable extraction medium and can extract Nd from iron alloys with high efficiency at around 1100 K. The newly developed extraction apparatus for Nd is a mechanically simple and static device without moving parts, where the Mg extraction medium circulates due to differences in the temperature inside the reaction vessel. This developed device can simultaneously accomplish continuous extraction of metal Nd from scraps, re-extraction of Mg from Mg-Nd alloy and the eventual recovery of pure Mg. As a result, metal Nd with 98 % purity was directly recovered from magnet scraps under certain conditions. It was also shown that the extraction agent Mg could be reused. The results of this investigation show the possibility of establishing a new process for the direct extraction of Nd in pure metal form without oxidization.

Jan 1, 2003

By Harald Laux, Stein Tore Johansen

The plunging jet in tapping of steel from converters or electric arc furnaces entrains gas into the steel bath contained in a ladle. Gas entrainment rate and the effect of the gas on the flow pattern in the ladle are studied by means of Computational Fluid Dynamics CFD. The work focuses on the mathematical modeling. Two numerical methods, one for free-surface flows and one for dispersed multiphase flow are combined. A transport equation for the average bubble diameter that incorporates the effect of coalescence and breakup is presented. Results from computations for one ladle and tapping configuration are shown. Our findings indicate that the gas entrainment rate is affected by the material properties of the liquid in the sense that the material properties determine the shape of the jet. Moreover, bubble sizes in the range of two-orders of magnitude are predicted in the ladle. The dispersed diameter model seems to work well. It showed the expected response to material parameters and the turbulent field. However, the presented analysis is just a first step that was limited due to certain simplifications. In order to obtain better insight in the tapping process improvements of the analysis seem necessary.

Jan 1, 1999

By N. J. Themelis

The basic chemical, thermal and transport principles that underlie sulfide smelting of. copper, nickel and lead are reviewed. Two basic types of modern smelting processes are distinguished?: flash-smelting, where the predominant reactions occur between oxygen-bearing gas and concentrate particles dispersed therein; and bath-smelting where the concentrate is enveloped and reacted in a turbulent bath of matte, slag and gas. The controlling heat and mass transfer phenomena are discussed, and appropriate correlations are proposed.

Jan 1, 1983

By Darryl Lovato, Ramiro Pereyra, Daniel S. Schwartz

"During an annual inventory of nuclear material, a plated steel container which contained plutonium oxide failed. The container had been packaged for temporary storage but had been overlooked and remained in storage for more than 23 years. Although it was determined that the failure occurred through the slip-top rim, a metallurgical evaluation was requested to help to determine the integrity of the container.Optical metallography and scanning electron microscopy were used to analyze the character and degree of corrosion in the container. The depth of corrosion, measured at approximately 10 µm, did not pose a threat to the integrity of the container. However, the corrosion morphology and chemistry did suggest that a galvanic cell had developed between the tin and steel from the condensation of water. The morphology also suggests that the attack of the steel took place over a series of cycles due to changes of the environment.IntroductionMetallographic analysis was requested as part of the investigation into the mechanism of the failure of a slip-top container (#38621) containing plutonium oxide (PuO2) powder. The container had leaked during a special nuclear material (SNM) annual inventory causing contamination and closure of the vault. A photograph of the container and interior container is shown on the right in Figure 1. An initial investigation established that the source of contamination was the consequence of the failure of multiple layers of containment. Initially by the deterioration of the interior plastic bottle and polyvinyl chloride (PVC) bagout bag, and finally through the lid and steel container interface at a location where tape had not adhered properly [1]. Although the source of the breach was established, it was determined that metallographic analysis was important to establish the extent of deterioration of the steel container."

Jan 1, 2008

By Jeffrey W. Fergus, Shiqiang Hui

"Aluminum is an important alloying addition to the zinc used in the hot-dip galvanization of sheet steel to control the properties and appearance of the resulting coating. Optimization of the galvanization process requires control of the alloy concentration which can be improved through the use of chemical sensors. Aluminum sensors based on molten electrolytes are commercially available but are not widely used because of their high cost. One approach to reducing the cost is to use a solid electrolyte which can simplify the sensor design and thus reduce the cost of fabrication. In this paper, the development of an aluminum sensor based on a solid fluoride electrolyte, specifically magnesium fluoride, will be described.IntroductionThe concentration of the zinc bath used in hot-dip galvanization affects the galvanization process as well as the properties of the resulting coating. Thus, accurate in situ measurement of the alloy composition can be used to improve process control. This paper describes a solid-electrolyte-based aluminum sensor for monitoring the bath composition during hot-dip galvanization."

Jan 1, 1997

By A. G. Guézennec

Electric Arc Furnace (EAF) steelmaking co-produces amounts of dust (15 to 25 kg per ton of steel), which require to be collected and stored in specific landfills. The collection, handling, and possible beneficiation of EAF dust depend on its composition and morphology. We first studied theoretically the chemical evolution of dust particles along the fume extraction system, from the furnace down to the filters, using thermodynamic calculations of the Fe-Zn-O system. We show how it would be possible to favor zincite formation in dust and therefore increase further zinc recovery. Then, we developed a new morphological model, based on population balances, for predicting the granulometric evolution of dust particles as a result of agglomeration and sintering in the fume extraction ducts. The contribution of the various mechanisms (Brownian, turbulent, and sedimentary agglomeration; thermophoretic deposition; coalescence and sintering) is assessed. The influence of the exhausting conditions on dust granulometry is detailed. For the extraction system studied, intense agglomeration of the sub-micronic particles and complete coalescence take place inside the furnace; micronic particles then undergo little evolution from the elbow to the water-jacket, whereas big agglomerates are formed downstream. These results are in good agreement with dust particle observations.

Jan 1, 2006

By J. Rajek

The novel multi-component, multi-particle, multi-phase precipitation model developed recently is used to predict the precipitation kinetics in complex 9-12% Cr steels investigated within the European COST 522 project. These steels are used for tubes, pipes, casings and rotors in USC (ultra super critical) steam power plants for the 21st century. In the computer simulations, the evolution of the precipitate microstructure is monitored over the entire production heat treatment starting with the casting process, including austenizing, several annealing treatments and in-service conditions. The main interest lies on the concurrent growth and coarsening interaction of different types of precipitates. Keywords: Precipitation kinetics, heat treatment, power plant steels, simulation

Jan 1, 2003

By T. K. Mukherjee

The importance of the processing of secondary resources such as solid industrial wastes and liquid effuents as well as byroducts for the recovery of the associated metal values hardly needs any elaboration. Such processing contributes in no small measure.towards the augmentation of the availability and the supply position of resources. As an added benefit, it leads to a reduction in environmental pollution caused by the undesirable waste materials. As some typical examples of secondary resources in the Indian scenario, mention' can be made of spent catalysts, metal/alloy scrap, ash, consumed batteries, flue dust, slag, sludge and slime, pickling solutions, spent acids; plating rinse solutions, spent etchants, waste water from synthetic fibre manufacture and from tanneries etc. These wastes constitute a source of a variety of non ferrous metals. In the processing of secondary resources like these, the techniques of hydrometallurgy such as solvent extraction play a pivotal role. This paper outlines the efforts made to use solvent extraction to recover (1) base metals such as copper, zinc, nickel and cobalt from a number of secondary resources like cake, and sludge(2) refractory metals like molybdenum and vanadium from sulphidic, byproducts and spent catalyst and (3:) nuclear metal like uranium from phosphoric acid. In the case of base metals, process flowsheet involving the use of acidic extractants such as DEHPA and PC88A have been optimised. The problem of iron removal from the leach liquor, "which influences the metal recovery process significantly, has drawn a special emphasis. hi the case of refractory metals, basic extractants .like Alamine 336 has been pressed into service to produce kilogramme. quantities of pure salts of molybdenum and vanadium, Finally, the paper gives a brief account of plant experience in recovering uranium from phosphoric acid, using 'a solvent system comosed of DEHPA and TOPO.

Jan 1, 1996

By Adam C. Powell

A new Cahn-Hilliard phase field model of transport-limited electrochemistry describes phase boundary motion due to oxidation and reduction reactions at metal-electrolyte interfaces. Benchmarks demonstrating the accuracy of the method include open circuit voltage and closed circuit current in metallothermic reduction, and linear stability theory in metal electrolysis, including a new stability criterion for reduction of liquid metal from liquid electrolyte. The model is applied here to understanding cathode interface stability in titanium electrolysis e.g. in the SOM process developed with Uday Pal, and to structure evolution in subhalide reduction of titanium dichloride by magnesium developed by Toru Okabe. Potential for application to new fuel cell and battery systems is also discussed.

Jan 1, 2006

By František Molnar, Zsolt Szentirmai, Juraj Schmiedl, Felix Sekula

"Hydrometallurgical nickel production in Sered Nickel Plant (Slovakia) that treated roasted Albanian ore left behind a considerable amount of the solid leaching residue. About 6 million tons of this fine-powder residue containing approximately 52 wt.% of iron in the form of oxides is to the present day stored in a stockpile. However, its iron content makes it a potentially interesting secondary raw material for iron production. This secondary raw material is not, unfortunately, suitable for direct treatment in iron and steelmaking processes.This paper presents results of the laboratory tests of pyrometallurgical method of processing of the leaching residue by its roasting and subsequent refining melting. The objective of the selective reducing agglomeration roasting was to reduce iron oxides and to simultaneously avoid reduction of chromium oxides and silica. Refining melting is carried out in an inert atmosphere. The products of melting are technically pure iron and slag.IntroductionThe leaching residue stockpiled on waste dump near already non-existing Nickel Plant Sered, Slovakia, is considered to be one of the most important environmental burdens in this country. The 40-years of an on-going effort focused on finding the methods for extracting metals and thus remove the waste dump have not been successful [1,4,5,6]. From the literature survey it is evident that past investigations have been following three main routes:1.Removal of chromium by mineral processing methods prior to its metallurgical treatment to achieve final chromium concentrations below 0.3 wt.%.2.Pelletization of solid leaching residue and its subsequent reduction in blast furnace and steelmaking plant and simultaneous removal of chromium.3.Pelletization of solid leaching residue followed by metallurgical processing of preliminary reduced semi-product in electric arc furnace (EAF) accompanied by partial reduction of chromium."

Jan 1, 2008

By Ross Baldock, Ross Andrews, Gu Helin, Lan Xu, Markus Reuter, Song Xingcheng

"A commercial lead smelter using Outotec Ausmelt TSL Technology has been successfully commissioned and put into operation at Yunnan Tin Company Ltd operations near Gejiu City, in Yunnan Province, China. The plant was commissioned in July 2010 after three years in the design and construction phase. The process uses a three stage batch process to produce lead bullion and zinc fume, and a slag that is low in metal values. The paper provides details of this lead smelting project, including the theoretical evaluation of the multi-stage process chemistry, engineering design, plant commissioning and the final operation. Comparison of the design targets and actual performance of the plant is emphasized. The fast ramp-up to full production of the largest Ausmelt TSL lead furnace built to date is highlighted.IntroductionIn 2002, Ausmelt and Yunnan Tin Company (YTC) successfully commissioned a smelter to modernise the Yunnan Tin smelter in Gejiu City, Yunnan Province, China. A single Ausmelt furnace was installed by YTC to process tin concentrate and revert materials, to produce YT Brand tin product. The advanced Ausmelt Technology furnace at YTC replaced seven existing reverberatory furnaces and provided a flexible, energy efficient and environmentally beneficial system to complement the world leading refinery facilities of YTC."

Jan 1, 2012

By Jr. Robison

"Aluminothermic (""thermite"") smelting became commercial with the development of tonnage aluminum, and prospered producing metals and alloys with higher cleanliness, consistency and elemental control than competing technologies. We explore the scope of thermite smelting, and metallothermic smelting in general; the thermochemistry of the process; and its advantages and limitations as applied to industrial production. We review currently-produced products of thermite smelting in several forms and a wide range of heat sizes. As these products serve several industries, we relate the demands of those industries to the requirements imposed on the thermite process, leading to process dynamics and mechanisms to control/alter those dynamics. We review ways to lower the process costs by altering process stoichiometry, using other energy sources and utilizing less costly materials while considering effects on product quality and customer requirements. Finally, we examine overall emissions control and waste disposal.IntroductionAluminothermic smelting is the reduction of various oxides by aluminum to produce metals or alloys with varying levels of residual aluminum. One of the earliest uses of the process was the production of liquid iron to weld railroad rails, later modified in ""thermite grenades"" used to ""spike"" artillery pieces in World War II. Then during the 50's, 60's and 70's the growth of jet aircraft created a demand for new superalloys and titanium alloys, both requiring master alloys for efficient production. Aluminothermic smelting grew with the aerospace industry and with the expansion of microalloyed steels. It is very much a niche industry, dependent on the specialized demands of the specialty steel, superalloy and titanium industries. In this paper we introduce the characteristics of aluminothermic smelting, the scope of smelting operations, the markets served, and the environmental aspects of the process, as seen through the eyes of a company using aluminothermic smelting for over fifty years"

Jan 1, 2012

By B. Q. Li, S. P. Song

"This paper describes an on-going research on developing coupled boundary element and finite element algorithms for the solution of thermal and electrodynamic problems relating to materials processing. The coupled methods are uniquely suitable for field problems involving composite regions, in which detailed information on field distributions within one particular region is of more interest and yet the solution can be obtained only if the effects of other regions are all considered. Problems of this type include heat transfer in multiple regions and also magnetic induction involving an infinite boundary. The hybrid boundary and finite element formulation, algorithm development and the applications are discussed. Two examples are given to demonstrate the capability and accuracy of the coupled algorithm for heat transfer problems. Various treatments of corner discontinuity are discussed. It is found that the double flux treatment is an ideal choice amongst those tested as it is easy to implement and also gives the most accurate solution. 1. INTRODUCTIONElectrodynamic and transport problems occur frequently in materials processing systems. Accurate solution of these problems is of great importance not only for our fundamental understanding of physical principles governing these phenomena in the processing systems but also for optimization of the existing processes as well as development of new processes. For this purpose, many numerical algorithms have been developed. These computational schemes in general can be classified into three categories, that is, the finite element and finite difference schemes and the boundary element scheme. The former two are domain based numerical algorithms while the latter the boundary-based algorithm.The finite element method, which is based on the variational calculus, is a very useful and yet popular engineering numerical method for boundary value problems defined over irregular boundaries. The use of the method requires the discretization of the entire domain. It can be applied to solve both linear and nonlinear problems, but is particularly powerful for nonlinear problems that involve the field variables defined within the computational domain. On the other hand, the boundary element method, with its root in the Green's function method, is very efficient for linear boundary value problems or nonlinear problems that involve field variables only along the boundaries. The primary advantage of the boundary element method lies in the fact that only the boundaries of the computational domain need to be discretized, and hence the dimension of the problem is reduced by one, compared with the finite element method."

Jan 1, 1994

By Hong Ro Lee, Seang Suk Cho, Byung Sun Chun, Chang Whan Won

"The preparation of Al203-SiC-TiC composite powders was studied by SHS process using silica (source of Si02) powder instead of Si which is expensive. And, aluminum powder was used as reducing agent of silica and charcoal activated was used as carbon source. Effects of the molar ratio in raw material mixtures and compaction pressure and initial temperature of reactant on the products and combustion process were studied. The most important variable affecting the synthesis of Al203-SiC-TiC was the molar ratio of carbon. The combustion reaction generated in powder state without preheating. But the unreactants exist in the product on all molar ratio. When the preheating temperature is over 400 °C, the combustion reaction was able to be generated in pellet state. Without preheating, the combustion reaction was possible by Ti02 addition. The optimum condition in this system was the molar ratio of Si02:Ti02:Al:C=2.5:0.5:4:3.1. INTRODUCTIONCeramics have demonstrated a capability as a cutting tool, especially in competition with WC-Co cermets (ceramic-metal composites) as inserts for metal turning and milling operation. The advantage of ceramics compared with carbides is retention of high hardness, strength, and chemical inertness to temperatures in excess of 1000 ·c . This allows use of the ceramics at much higher machining speeds than can be tolerated by carbides. However, the ceramics have lower toughness than the carbide materials, and have only been used successfully in the limited operations of turning and milling. There are several classes of cutting tools. The addition of TiC or PSZ, or both, and reinforcement with SiC overcame the poor fracture toughness and thermal-shock resistance that limited Al203 use in the past [1]."

Jan 1, 1998

By Albert Wraith, Thomas Price, Wayne Boyd, Skip (I. E. ) Hills, Cameron Harris

Most Peirce-Smith converters inject air through tuyeres, with nitrogen representing the majority of gas passing through the process. The nitrogen controls the temperature of the vessel by carrying away heat from the reactions, both globally and locally at the tuyere tip. However, nitrogen adds energy to the bath and contributes to splashing and limits the blowing rate. High oxygen smelting has made streams of gas containing high concentrations of sulphur dioxide commonplace, which can be used to substitute SO2 for nitrogen and drastically changes Peirce- Smith converting (and all other smelting/converting processes as well). Less SO2 is required to carry away the same quantity of heat, which allows higher concentrations of oxygen and leads to the possibility of increased production. The paper investigates this substitution, its impact on converter productivity, and on the remainder of the plant. 181

Jan 1, 2009

By N. L. Piret

Primary and secondary copper smelting dusts are being generated in varying quantities with very dissimilar characteristics due to the different compositions of feed materials and the type of process utilized. After categorizing the multitude of dust types, the criteria for on-site and off-site recycling of smelter dust in terms of type and concentrations of the accompanying elements are established. Thereby, consideration is given to the important aspects of: ? optimization of copper recovery ? quality of copper product ? valorization of accompanying elements ? elimination and disposal of deleterious impurities ? minimization of impact on operation ? effects on operating costs ? environmental impact of dust treatment on overall process Existing commercial, emerging and proposed copper smelting dusts, pyrometallurgical as well as hydrometallurgical, treatment schemes are reviewed and evaluated technically, economically and environmentally in an attempt to streamline the vast number of proposed options. Thereby, the high selectivity achievable in hydrometallurgical dust processing due to it being complementary to the smelting process is expected to be given increased consideration.

Jan 1, 1995

By Qiang Yu

This paper reports on a research project supported by NSF, which aims at developing a multi-scale methodology for systematic microstructure prediction in thermo-mechanical processing of metals. This methodology is based on combining mesoscopic microstructure models with macroscopic process formulations and involves the following three main steps: (I) based on the given global processing conditions, the gross deformation patternof the entire workpiece is modeled using a continuum-based algorithm, (2) the resulting parameters are then extracted from the continuum-based simulation, post-processed and passed on to the mesoscopic numerical module, and (3) the microstructural changes are finally modeled at the mesoscopic scale. This approach is expected to overcome the disadvantages of current microstructure prediction practice employing empirical relationships between microstructural features and processing parameters. Keywords: Thermo-mechanical processing, Microstructure, Grain growth; Recrystallization; Mesoscopic models; Finite Element Method

Jan 1, 2003

By Maura Malone, Neil Gao, Daniel Liu

"Corrosion is the primary failure mode for aluminum cathode sheets used in Teck's Trail Operations electrolytic zinc plant. It was observed that the corrosion performance of Al cathodes from different suppliers varied considerably. This suggests that the material properties of Al cathodes have a strong influence on corrosion resistance. In the current study, various types of Al alloys, including 1050, 1060, 1070, HIS and 1090, were characterized through chemical analysis, corrosion testing, mechanical testing and metallography. The results are discussed with a focus on the effects of impurity elements and second phase particles on corrosion resistance. The findings were used to improve the Al cathode sheet specification and to develop a standardized screening procedure which details qualification steps for comprehensive evaluation prior to a plant trial.IntroductionAluminum (Al) cathode replacement is a major operating expense at Teck's Trail Operations zinc electrolytic plant. Currently, approximately 0.5% of daily stripped Al cathodes are removed from service because of failures caused mainly by corrosion. Edge corrosion and acid (solution) line corrosion are the most severe types of corrosion, resulting in more than 50% of cathode failures.Corrosion of Al cathodes has been intensively investigated for over two decades and the origins and mechanisms of Al cathode corrosion are well understood [1-4]. Halide anions contained in the electrolyte are the primary culprits for the corrosion and sticking problems of Al cathodes. Both fluoride (F') and chloride (Cl"") result in localized passivity breakdown on the surface of the Al cathode, causing pitting corrosion. Bouarzaiga investigated the corrosion of Al cathode samples partially immersed in electrolyte and found that the formation of Ch at the electrolyte/air interface was the primary contributor to solution line corrosion [2]. Because of the significant impact of F"" and Cl"" on Al cathode corrosion, it is imperative to maintain these concentrations as low as possible in the electrolyte."

Jan 1, 2012