Search Documents

By Yasuhiro Konishi, Yoshiyuki Noda

"This paper describes a new processing of rare-earth oxide precursor, in which rare-earth carbonate powders are precipitated directly from emulsions of rare-earth loaded carboxylate solutions, using CO2 gas and water. This synthetic route of rare earth carbonate is a combined process of the stripping and precipitation stages in a conventional solvent extraction. Using this technique, lanthanum carbonate and yttrium carbonate were prepared at temperatures of 10 to 80°C and CO2 pressures of 0.1 to 3.0 MPa for 120 min. The rates of carbonate precipitation in a batch autoclave were sensitive to processing parameters such as CO2 pressure, temperature, and organic-phase composition. The particle size distributions of the carbonate powders were markedly dependent on temperature and C02 pressure.IntroductionSolvent extraction is the most appropriate commercial technology for separation and purification of rare earths. In typical commercial processes, the rare earths are stripped from loaded solvent extractants using aqueous solutions of mineral acid. After adjusting the pH of the aqueous strip solution, the rare earths are precipitated as insoluble powders of oxalates or carbonates, from which oxides can be produced by calcination. Such conventional processing can be simplified when the stripping and precipitation stages are combined by emulsifying rare-earth loaded solvent extractant with aqueous oxalic acid solution. It is likely that the single-stage precipitation stripping results in a marked decline in the consumed amounts of precipitating and neutralizing agents, thereby saving on both running and capital costs.Yoon and Doyle1) first demonstrated that oxalate powders of lanthanum and yttrium are directly precipitated from rare-earth loaded carboxylic acid solvent extractant when contacted with aqueous oxalic acid solution at ambient temperature and atmospheric pressure. Yttrium oxalate pow4ers were also prepared by precipitation stripping of di-(2 ethylhexyl) phosphoric acid. (D2EHPA) extractant using oxalic acid-hydrochloric acid solutions. 2) Moreover, neodymium oxalates were directly precipitated from organic solutions of tertiary aliphatic monocarboxylic acid and 2-ethylhexyl phosphonic acid mono-2- ethylhexyl ester using aqueous oxalic acid solutions, and powder characteristics of the resulting oxalates were compared with those of powders by the conventional solvent extraction routes. 3 • 4) Recently, attention has been directed towards the influence of processing parameters on the particle size distributions of yttrium oxalate precipitates. 5)"

Jan 1, 2000

By Lianjun Liu, Ying Li, Qianyi Zhang

"Photocatalytic reduction of CO2 by H2O for production of Cl fuels (CO and CH4) was studied using copper and iodine co-modified TiO2 (Cu-IffiO2) nanocomposites, with copper deposited on the surface and iodine doped in the lattice. The nanocomposites were prepared via a combined hydrothermal and wet impregnation process. All I-doped samples demonstrated visible light activity. Under UV-vis irradiation, co-modification of Cu and I significantly increased TiO2 photoactivity compared with bare TiO2 or those modified with only one species.IntroductionThe photoreduction of CO2 into fuels on photocatalysts such as TiO2 has been regarded as an important approach to solve both energy shortage and globe warming problems [1]. However, the wide band gap and fast recombination ofphotoinduced hole (h+) and electrons (e"") limited the application of TiO2 in CO2 photoreduction reaction. Extensive research has been conducted to improve the photocatalytic ability ofTiO2 by depositing or doping foreign ions that can enhance charge transfer and/or creates intra-band-gap states to induce visible light absorption at the subband- gap energy. Compared with mono-doping, co-doping of metal/nonmetal species has been reported to have higher photocatalytic activity for TiO2 [1-3]. Our previous studies showed that Cu deposited on TiO2 [4] or iodine doped in TiO2 [5] significantly enhanced the catalytic efficiency for CO2 photoreduction and increased the response to visible light. We hypothesize that there could be a synergetic effect if TiO2 is co-modified by both Cu and I species resulting in further improvement in CO2 reduction efficiency. In this work, we synthesized and characterized Cu-IffiO2 samples and investigated their activity toward CO2 reduction under visible and UV-vis illumination, respectively.Experimental MethodsMaterialsTitanium tetra-isopropoxide (TTIP, 98%) and isopropanol (C3HsO, 99.8%) were purchased from Acros Organic. Iodic acid (HIO3,99.8%) and Copper Chloride (CuCh, 99.9%) were purchased from Alfa Aesar. All other chemicals were analytical grade and used without further treatment."

Jan 1, 2012

By Wilson Pascheto

This paper presents results of investigations performed as part of a Root-Cause-Failure-Analysis (RCFA) of a DC smelting furnace that was brick lined with MgO-based refractories. An unusual continuous contraction of the furnace hearth was identified during operation. Cracks in the refractories were envisaged after a major shutdown of the furnace. To determine the mechanism and causes of the unusual contraction behaviour of the furnace hearth, refractory samples were taken from the furnace at different locations and subjected to different analysis including Scanning Electron Microscopy (SEM), Energy-dispersive X-ray spectroscopy (EDX), QEMSCAN and Electron Probe Micro Analysis (EPMA). Creep testing of refractories under different loads (ASTM C832) was also employed to evaluate the mechanical integrity of the used bricks in comparison with the new ones. Results of the various characterisation analyses revealed that there was an interaction between refractory bricks and molten material during furnace operation, which resulted in reduced creep resistance of the MgO-based refractories. This was verified by comparing creep performance of the used brick samples and new brick samples at different temperatures and applied stresses.

By Sudha Goel, Manis Kumar Jha, Deblina Dutta, Rekha Panda

Based on the placement of lead and its consumption in industry bran- ches, the paper deals with the composition of lead in the massive of Kopaonik. Removal, tenuity and grinding of galenit. The paper in particular treats the flotation process, and also treats physico-chemical bases of reagents in the process, as well as decanting, drying, filtering and storage of concentrates. Veri fication of the chemical composition of Pb concentrates with Pb, Zn, Bi, As, Sb, In, Au, Ag, etc. It is special that in Kopaonik massive the ratio of Pb: Zn composition is 1.4:1.0 and during the flotation lead is inclined to go with pirotines concentrate more than is allowed. We are strongly focused to maximally decrease the Pb amount that goes with pirotine concentrates and wastes. The paper as such gave the first effects in optimizing of these parameters with positive effects in flotation process in Trepca.

Mar 1, 2018

By Jose Castro

The growing demand of scrap to supply the electric arc furnace has driven to search for new alternatives of raw material. The DRI produced using self-reducing pellets has become competitive due to the potential use of a wide range of carbonaceous materials such as coal, charcoal, biomass etc. In this context, the rotary kiln process using improved technologies such as post-combustion and self-reducing burden is a promising source of high quality raw materials. This paper presents a mathematical model of the rotary kiln process designed for self-reducing pellets and post-combustion. The model is based on the transport equation of two-phase flow, energy and mass transfer. The solid material is composed of a typical self-reducing pellet. The model considers the solid phase (C, volatiles, Fe2O3, Fe3O4, FeO, Fe, H2O, SiO2, Al2O3, MgO, P2O5, K2O, Na2O, FeS, CaO and gangue) and the gas phase (N2, O2, CO, CO2, H2, H2O, SO, SO2 and SiO). For each of the above components a conservation equation is solved and the mass and energy transport is accounted. The set of differential equations are coupled by the rate equations describing the kinetics of the several reactions, which take place within the rotary kiln. All the conservation equations are solved based on the finite volume method applied for a three-dimensional cylindrical coordinate system. Simulation results are presented for global parameters such as metallization degree, productivity, gas utilization ratio and calorific value. Inner conditions such as three-dimensional gas and solid temperature patter and compositions are discussed.

Jan 1, 2006

By Joel A. Huffinan

"This presentation is being given to better inform the audience of the dependability of precious metal analysis by fire assay. A brief explanation, however, of standard fire assay exploration procedures will be given. An overview of other types of analyses by fire assay will be discussed as well, and the operation of a modern day assay laboratory.IntroductionThe use of lead oxide for the fire assay process dates back to the finds in Troy II and the Cappadocian Tablets about 3,000 B.C. Some advances have been made in the basic procedures due to instrumentation and electronics, but the fusion and cupellation procedures used in fire assay remain much the same as during this period.In 1600 AD. Agricola was the first to take a scientific approach to fire assay recording methods and procedures used (Hillerbrand and Allen, 1905) [1]. Since this period, much of the recognized research into the analysis of ores and metals was carried out in the late 1800's and early 1900's prior to World War II, and again after the deregulation of precious metals. The renewed interest in precious metals mining and metallurgy are due much to advances in precious metals heap leaching in late 1970's."

Jan 1, 1999

By Girley Ferreira Rodrigues, Crocce Denise Romano Espinosa, Victor Bridi Telles, Eduardo Junca, Jorge Alberto Soares Tenorio

"Steel sector is responsible for the generation of solid waste, liquid and gaseous effluents. The Solid waste are mainly composed of slag, dust, sludge and scrap. The industry generates approximately 650kg of solid waste per tonne of steel. Approximately 10% of this waste is in the form of dust and mud. The basic oxygen furnace dust is a waste generate by steel sector. Each tonne of produced steel generates 10 to 20 kg dust. Thus, the aim of this paper is study the reduction of pellets made with BOF dust using hydrogen and study kinetic during the reduction. The tests were performed in a netzsch thermobalance to obtain the data of lost mass. This loss mass is coming from iron oxides present in the BOF dust.IntroductionThe generation of solid waste is a problem for many companies in the steel sector. The main solid wastes generated are slag, dust, sludge and scrap [1]. Beyond solid waste liquid and gaseous effluents are also generated.The basic oxygen furnace is responsible for 60% of all steel produced. This sector is the second largest generator of solid waste from an integrated steel mill, contributing with 27% of solid waste generated in a plant ( 5-7 million tons of waste generated annually worldwide) [2,3,4]."

Jan 1, 2013

By Edwin de Jesús Deveaux

After 32 years of operations beneficiating lateritic nickel ore in a fully integrated pyrometallurgical complex, Falconbridge Dominicana (FALCONDO), situated at Bonao and La Vega Provinces, Dominican Republic, has become profitable with one of the lowest nickel grade content processing plants in the world, and literally without any by-product (granulated slag, will be utilized in the future as a post-processing subproduct). To December 2002, mineral reserves were 64.1 million tonnes containing laterite grading as low as 1.15 % Ni when full dilution is applied. At a cut-off grade of 1.20% Ni, the reserves will provide 15-20 years of production. The mineralized thickness over the seven active deposits averages 6 m. Development of very selective and unique mining practices, together with improvements in the process plant, are key to achieving the production goal (30 kt Ni/yr) and to meet the quality standards for the ferronickel produced. Keywords: Laterites, grade control, mining methods, environment

Jan 1, 2004

By Brent W. Madsen

The acid-ferric sulfate leaching of low-grade sulfide copper mine waste provides more than 10 percent of the U.S. supply of new copper, but recoveries and leaching rates are very low. In Federal Bureau of Mines research to improve the leaching process, experiments on 5- to 10-ton lots of mine-run ore were more revealing than bench-scale tests on fine ore. This report discusses the results obtained by leaching run-of-mine and minus 6-inch plus 112-inch samples of low-grade chalcocite-bearing mine waste. The samples were leached for 461 days and 61.6 and 37.7 percent of the copper was extracted from the minus 6-inch plus -112-inch and run-of- mine samples, respectively. A mixed kinetics model was applied successfully to the leaching of the sample with the fines removed where bulk solution transport was not rate controlling. The model, when applied to the run-of- mine ore, gave somewhat higher predicted copper extractions than experimentally determined. Subsequently, oxygen was introduced into the run-of- mine ore, leaching continued for an additional 312 days, and an additional 53.0 percent of the copper was extracted. Before the leaching experiment was dismantled and the residue sampled, the ore was treated with sulfur dioxide and its permeability was improved markedly. The results of each of these procedures are interpreted in relation to the attendant condition of the test.

Jan 1, 1976

By K. Prashant Sarswat

Isotopes are critical to a variety of applications including physical science analyses, biology, medicine, pharmaceuticals, and national security. In most cases isotopes must be relatively pure or highly enriched before they become useful. Current isotope separation technologies are relatively inefficient, capital and labor intensive, and often produced by a limited number of suppliers. In the category of isotopes, lithium is among other important candidates. Lithium is found naturally in two isotopes, 6Li which accounts for 7.5% of all lithium, and 7Li which makes up the balance of 92.5%. Each of these isotopes is important to the nuclear industry. 7Li is often used in the form of lithium hydroxide which is used to control pH in pressurized water reactors. The current supply of 7Li is based mostly outside of the United States, and its long-term supply is uncertain. Apart from supply issues, the use of mercury for 7Li separation is also a concern in commercial processing using the most common and efficient approach [1–3]. Hence, a reliable, environmentally friendly, and efficient technique is needed to produce 7Li. In this line of investigations, the authors used a two-compartment system and significant separation was achieved. In this piece of research, some preliminary results are presented including cell design and actual isotope ratio after enrichment. Applying an electro-potential across two electrodes can be used to drive electromigration of Li isotopes. The electromigration is in addition to normal diffusion. Note that 6Li diffuses faster and hence there will be a lowering of the 6Li concentration near the positively charged electrode and an enhancement in 6Li near the negative electrode during the separation process. Similarly, 7Li will be more prevalent near the positive electrode and less prevalent near the negative electrode during the initial separation stage [1].

By S. Chama, P. Chishimba, Tina Chanda Phiri, J. Machona, S. Parirenyatwa, G. Kaluba, Y. R. S. Hara, D. M. Musowoya

The investigation focuses on leaching of copper (2 wt%), cobalt (0.5 wt%) and iron (2.4 wt%) from complex tailings material from the Democratic Republic of Congo. The highest recovery of copper and cobalt into the leach solution were 78 and 10%, respectively, under direct leaching with sulphuric acid. Higher recoveries (90% for copper and 96% for cobalt) were attained when the material was pre-reduced with coal for 1.5 h in the temperature range of 700–950 °C. The increased recoveries were due to metallisation of all the copper and cobalt which is in the silicate matrix. The effects of pre-reduction temperature and sample to carbon weight ratios were analysed and found to be important in; (i) achieving high recoveries of copper and cobalt and (ii) decreasing the amount of iron in the leach solution. The samples were characterised by atomic absorption spectroscopy and scanning electron microscopy (SEM) techniques.

Mar 1, 2017

By Li. Jiarong, Zuojian Liang, Qingyan Xu, Baicheng Liu, Shizhong Liu, Hailong Yuan

Single crystal solidification of turbine blades is a key technology for the production of reliable and high efficiency gas turbines. The solidification process of single crystal investment castings causes a number of problems that have to be solved such as the increase of casting defects and complexity of production process. Computer modeling and simulation is helpful to predict the defects and improve the process design. In the paper, a mathematical model for three dimensional simulation of solidification and single crystal growth of investment castings was developed based on CA, mechanism of crystal growth and basic transfer equations such as heat, mass transfer equations. Many factors including constitutional undercooling, curvature undercooling and anisotropy, which had vital influences on microstructure evolution, were considered in the model. Temperature, crystal growth interface and structure defects of investment castings of single crystal superalloy were investigated at withdrawal rates of 4.5mm/min and 7mm/min. Simulated results showed that microstructure evolution and structure defects were predicted reasonably and calculated results were coincident with experimental ones. The study indicated that three dimensional solidification simulation technique is a powerful tool for understanding the fundamental of solidification and the formation of structure defects in single crystal investment castings and finally for optimizing process design.

Jan 1, 2004

By Christian Bernhard, Mario Hartl, Susanne K. Michelic

"One aspect of an efficient process and product optimization of the liquid steelmaking process is the understanding of reactions and interactions between the components steel, slag and nonmetallic inclusions. The present paper focuses on a fundamental study of this topic by combining the powerful methods of thermodynamic modeling with systematic experiments on a laboratory scale and subsequent SEM/EDS analyses. The modeling aspect is addressed by the commercial software FactSage 6.1; laboratory experiments are performed for a low-alloyed, Ca-treated carbon steel combined with varying slag compositions. The consequent SEM/EDS analyses provide a detailed insight into the inclusion landscape which offers a strong tool for characterizing the modification of inclusions. In the present study the combination of these methods is mainly applied to oxides, due to their crucial influence on the final product quality, thus giving important indications for further optimizing the secondary metallurgy processes.IntroductionIn recent years, the range of application for steels has been enlarged continuously; also resulting in extreme surrounding conditions combined with considerable stresses for the material. This trend is directly linked with higher demands on the properties of steels. In order to optimize the final product quality, the cleanness of steels is an important criterion. For this reason, the broad topic ""Steel Cleanness"" has become one of the main research points at the Chair of Metallurgy. Next to the continuous optimization of methods for the characterization of cleanness, the primary aim is to combine thermodynamic modeling and laboratory experiments in order to describe the changes in inclusion landscape under different conditions.The steel cleanness can particularly be influenced in the processes of secondary metallurgy. In different processes the reactions and interactions between the components steel, slag and nonmetallic inclusions (NMI) are essential for the final inclusion landscape. Consequently, the understanding of the occurring reactions is a fundamental aspect for further development and process optimization. In secondary metallurgy especially oxide-slag systems consisting of the components Ca0-Ah03-Mg0-Si02, which significantly influence the modification of NMI, are of importance. Several works dealing with the interactions of oxide non-metallic inclusions with different slag systems have been published in the last years [1-4]. In order to observe the dissolution of oxides in different slag compositions a Laser Scanning Electron Microscope is frequently used. A very detailed study on the ternary system Ah03-Ca0-Mg0 and its subsystems was also done by De Aza et al. [5, 6]."

Jan 1, 2011

By Deventer Johanna van

Ore bodies around the world are declining in grade, whilst increasing in complexity. The level of impurities relative to the valuable metal is steadily increasing, posing new challenges to existing operations. Ion exchange is widely used in the hydrometallurgical industry for both primary recovery of metals and the removal of impurities. The superior selectivity of ion exchange resins makes them exceptionally suitable for the removal of target impurities to very low levels, thereby saving operating costs, increasing the value of the final product and significantly improving revenue. The ion exchange process in these applications is very simple, using standard ion exchange equipment and acid regeneration. The process can be fully automated, requiring minimal operator interference and supervision Examples of impurities that are successfully removed via ion exchange include iron, antimony and bismuth from copper electrolyte. In the copper electrolysis process, antimony, bismuth and arsenic tend to form slimes which are dispersed in the electrolyte. These slimes contaminate the cathode and/or decrease the quality of the copper deposition. A special chelating resin was developed to remove antimony and bismuth, while at the same time ensuring minimal chloride leakage to the sulphate matrix. The work is described in more detail in this paper. Ion exchange is also used to remove copper, zinc and nickel from cobalt electrolyte. This paper addresses a few of these examples in more detail.

By Xuerong Wen

The oxidation behavior of TiAl3 intermetallics was investigated as a hnction of time at 1273K in pure dry oxygen. The oxidation experiments were carried out using TGA method. The oxidation scales were analyzed using SEM, EDS and X-ray diffraction methods. The structures of oxides formed at the different oxidation times were analyzed. The mechanism of oxidation of TiAl3 intermetallics was discussed.

Jan 1, 1998

By George P. Demopoulos

n this study we have sought to highlight the critical linkage between individual reaction kinetic parameters (usually determined in small bench scale experiments) and large continuous reactor performance by focusing on the industrially significant zinc pressure leach process. To this end a comprehensive mathematical model previously developed for the description of this process was employed. In this paper we have examined in particular how small variations in key kinetic parameters impact on the autoclave&apos;s performance, i.e. attainment of autogenous steady-state temperature, zinc conversion and solution chemistry. The reaction parameters studied were: (i) stoichiometry of the marmatite leaching reaction; (ii) the activation energy of the same reaction, E,; (iii) the rate constant of the ferrous to ferric oxidation reaction, k,; and (iv) the apparent equilibrium constant for ferric precipitation, K,. This parameter sensitivity analysis was done under no oxygen mass transfer control limitations. Model predictions were found to be more sensitive to the kinetic parameters under certain conditions than others. The most dramatic finding was the one related to the small amount of sulfate produced during marmatite leaching. In connection to this it was found that the small percentage (< 5 %) of sulfate produced enhances the autothermal operational stability of the autoclave. The need for accurate kinetic parameter determination under conditions similar to those encountered in industrial zinc pressure leaching was demonstrated.

Jan 1, 1999

By Kazuaki Mita

There are various intermetallic compounds in the Zn-Fe system. We synthesized them at about 673K. A specimen was examined chemically and X-ray diffraction was applied to ensure the formation of intermetallic compounds. Material containing two phases was placed in a Knudsen type effusion cell and the mass spectrum studied to evaluate the vapor pressure of zinc. The thermodynamic properties of intermetallics was then evaluated through measured intensity.

Jan 1, 1999

By William Petruk

Many gold operations lose gold during processing because some ore characteristics which affect recoveries have not been determined, and consequently the plant could not be designed to account for them. The ore characteristics can be determined with mineralogical techniques by analyzing the plant feed, final tailings and mill products. The plant feed and/or final tailings are commonly analyzed first as a separate project. Mill products are analyzed only if the process employs a minerals separation circuit to produce a concentrate (e.g. secondary flotation circuit to concentrate gold-bearing arsenopyrite), and if assays and materials balances indicate a recovery problem in the minerals separation circuit. Many ores have been evaluated at CANMET on a confidential cost-recovery basis by custom-designing a work plan which was dependent upon the problem and on the characteristics of the ore. The reasons for gold losses have been identified in most cases, and suggestions for modifying flowsheets have been proposed. The methods used in performing the analyses are described in this paper, and non-confidential results from in-house projects are provided as examples of the benefits of such analyses. The analytical methodology involves a combination of the following procedures: -producing heavy mineral concentrates and identifying the gold minerals in the concentrates; -determining quantities of invisible gold in gold-bearing sulphides, sulpharsenides, etc. by SIMS; -determining quantities and liberation characteristics of all gold minerals and gold-bearing minerals in the sample; -finding and identifying gold minerals in silicates; -extensive grinding and cyanidation to determine the ultimate amount of cyanidable gold; -determining impact of clay minerals and graphite; -performing a mineral balance for the gold in each sample; -performing a materials balance to determine the distribution of the gold minerals, gold-bearing minerals, and other minerals throughout the flowsheet, and; -interpreting the results.

Jan 1, 1995

Two pilot-plant investigations were conducted in which strong-base resins were compared with activated carbon for the extraction of gold cyanide from leached pulp from the Golden Jubilee Mine. The results show that gold can be recovered with carbon, but that the extraction efficiency is poor, probably because high concentrations of humic and fulvic acids are. present m the pulp. .However the extraction of gold cyamde from this material with strong-base resins JS very effo:1ent, and the overall efficiency of extraction is better with resin than with carbon, even when the concentration of resin is one-third that of carbon, and the flowrate of resin is one-third that of carbon. The results of the pilot-plant campaign reported in this paper led to the conversion of the Golden Jubilee plant from carbon-in-pulp to resin-in-pulp in February 1988.

Jan 1, 1989

By Ritayan Chatterjee, P. K. Mukhopadhyay, Surajit Biswas, Dinabandhu Ghosh, Sandeep Agarwal

An Indian magnetite ore from the Nagaland region was characterized by powder X-ray diffraction, spectroscopies (ultraviolet-visible and Raman), high temperature magnetization and thermal analysis. A Rietveld refinement of the diffraction data revealed that the principal phase present in the sample is magnetite with partial substitution of Fe with Mg (mainly) and Cr, leading to the chemical formula of MgCr0.2Fe1.8O4. The UV-visible spectra of the sample in MeCN solution showed three distinct peaks. The lower region bands are due to metal-oxygen charge transitions and the other band is for d-d transition of iron. Raman spectral study at room temperature gave four characteristics bands of magnetite. The sample underwent a magnetic transition at high temperature and the thermomagnetization curve shows hysteresis during cooling cycle which indicates the possibility of first order structural transition at high temperature. The thermal property of the concentrate was studied by differential scanning calorimetric technique.

Mar 1, 2018