Search Documents

By Peter G. Smith

Tri-calcium aluminate (TCA) is a dominant alkaline component of the red mud residue from the Bayer process. A method being considered for industrial implementation partially neutralizes the residue by contacting it with gaseous CO2. This paper outlines the chemistry of CO2neutralisation of TCA under conditions relevant to the treatment of Bayer residue. CO2 neutralisation of the liquor is fast. It results in the formation of amorphous aluminium hydroxide and dawsonite that agglomerate together. Neutralisation of solid TCA is slower and leads to the formation of calcite, dawsonite and amorphous aluminium hydroxide. The dissolution of TCA in partially neutralised slurries causes pH reversion. However the carbonated solutions contain a store of bicarbonate that can supply aqueous carbon dioxide to complete the transformation. The pH at which the carbonation is carried out will affect the degree of TCA transformation during the carbonation process. In particular, if the pH of the carbonation is too low (near 7.0), calcite precipitation is inhibited and the degree of transformation is low. Controlling the carbonation pH helps to optimise the neutralisation process.

Jan 1, 2003

By Alessandro Navarra, Joël P. T. Kapusta

"The converting cost modeling software introduced by Ng et al. in 2005 [1] has been extended to consider the reprocessing of reverts and copper scrap. The original model evaluated the operational costs of a Peirce-Smith converter; algebraic relationships had been implemented with arrays (to represent matrices, vectors and scalar ratios). The new software brings flexibility to the underlying thermochemical balances, by using linked-lists instead of arrays. It is now possible to consider the blending of several feeds, including reverts and scrap.The software computes the length of the converting cycle from the Fe and S content of the charge together with the blowing rate; the times required for other operations (charging, skimming and idle time) are also accounted for. The costs of consumables such as flux, fuel, oxygen or compressed air are all evaluated. Downtime, labor, and materials for converter lining repairs are also considered. The software is easily extended to examine the costs of alternative operating strategies or injection technologies such as sonic single pipe injection and sonic shrouded injection. The potential cost benefits of alternative operating procedures and technologies are discussed through example calculations."

Jan 1, 2009

By Steven Wright

BHP Billiton?s Olympic Dam copper flash smelter employs the direct to blister process for smelting high grade copper concentrates. SO2 evolution during tapping gives rise to safety concerns. A thermodynamic model for the blister copper (Cu-Fe-S-O) was used to predict the volumes of SO2 evolved. The Multiple Phase Equilibria Model (MPE) was used to evaluate the slag chemistry inside the furnace. The blister copper model was used to explore the relationship between %S and %O in the copper and the amount of SO2 evolved on cooling. The volume of SO2 evolved was sensitive to the O content with reduction to levels below 0.2 ? 0.15% likely to suppress SO2evolution on cooling. Concentrations of S and O in copper samples from trials generally lay above the equilibrium line calculated for an average temperature of 1275C and a partial pressure of SO2 of 1 atm. Consequently there is a thermodynamic driving force for SO2evolution when cooling to this temperature during tapping. A number of potential process options to suppress SO2 evolution on tapping were investigated thermodynamically. Some of the options require treatment of the blister in a forehearth or separate furnace, while others impact on current practises in the flash furnace with slag present. The opportunities that these options present are discussed.

Jan 1, 2006

By John R. Goode

The fist part of this paper comprises a general discussion on refractory gold ores and their mineralogy. Processing methods now in use are reviewed and test procedures for the important methods are discussed. Factors determining the selection of a process are outlined. The paper includes a survey of production plants using pressure oxidation, roasting and biological oxidation to process refractory ore. The status of processes under development is briefly reviewed.

Jan 1, 1993

By Hiroyuki. Fukuyama

The pseudo-binary phase diagram of the cuspidine (3CaO2?SiO2?CaF2) - CaF2 system has been studied by electron probe microanalysis (EPMA) and X-ray diffractometry (XRD). To prevent fluorine loss in the form of a HF gas by a reaction of CaF2 with water vapor at elevated temperatures, the equilibrium experiments were conducted with the sample hermetically sealed in a platinum tube. By employing this technique, it was successfully revealed that cuspidine exists as a stable phase and congruently melts at 1684 ± 1 K, and the cuspidine - CaF2 system presents a simple eutectic type of phase diagram, of which eutectic temperature has been estimated to be around 1540 K, corresponding to the composition of 40 mass% 3CaO?2SiO2 - 60 mass% CaF2?

Jan 1, 1999

By A. L. Davies

The MTDATA computer software package consists of a rigorous implementation of an algorithm for calculating chemical phase equilibria by the technique of Gibbs free energy minimization and a database of the thermochemical properties of common materials, such as slags, mattes, metals, gases and aqueous solutions. We have used MTDATA to contribute to our understanding of the chemical reactions occurring in several specific unit operations of the Kennecott Utah Copper Garfield Smelter. The following two examples illustrate the range of environments to which the method is applicable. Calculation of the liquidus phase relations of the FSF fayalite and FCF calcium ferrite slags helped in the early diagnosis of several operating problems. Calculation of the deportment of fluorine between the FSF offgas and the FSG scrubber liquor helped in the identification of operating conditions under which significant hydrogen fluoride concentrations could be introduced to the contact section of the acid plant. Without the painstaking assessment of solution phase properties undertaken over many years, these calculations would not be possible.

Jan 1, 1999

By M. I. Novgorodova

An overview of the systems Au-Ag and Au-Cu is given. The nature and levels of concentration of various elements occurring with native gold is reviewed. The examples cited are mainly from the USSR. The lack of homogeneity within naturally occurring Au-Ag solid solutions is examined.

Jan 1, 1991

By Wei-feng Liu

On the basis of the brief introduction of the gold-antimony concentrate smelting process in China, some problems in the original process were analyzed and the corresponding improvements were introduced in this paper, such as the treatment of antimony matte, the refinement of gold-silver alloy, the concentrating gold from gold-antimony alloy, the treatment of soda slag. The roasting method that was used to treat the antimony matte was transferred to the ore dressing method. The solvent extraction was used to refine the gold-silver alloy instead of the electrolytic method. The technology of selective chlorination leaching under controlling potential was applied to concentrate gold from the gold-antimony alloy and gold-lead alloy instead of the electrolysis method. Soda slag was recovered by the second reducing smelting method substituting for the mixed-salt method of sodium arsenate. After those improvements, the process has been done smoothly; the direct recovery rate of metals has been greatly increased. Meanwhile the procedure

Jan 1, 2008

By S. N. Monteiro, N. A. Cerqueira, E. B. Zanelato, J. Alexandre, M. T. Marvila, B. C. Mendes, A. R. G. Azevedo, G. C. Xavier

Mortar is a widely used building material and has its application in buildings in extremely vulnerable environments and susceptible to degradation, such as facades. The objective of this work was to evaluate the loss of mechanical resistance to compression and flexure and the loss of mass of the mortars with effluent sludge from paper industry, when exposed to saline environments. The specimens were done with 0, 5, 10 and 15% of incorporation in lime paste and subjected to saline mist equipment that sprays salt solution in cycles simulating natural degradation conditions using literature data. It can be concluded that mortars with a15%incorporation obtained a significant loss of mass and a decrease in their mechanical resistance, which impairs their use in civil construction and influence in other properties of the material, with a level of incorporation of 10% the results within Brazilian standards.

Mar 1, 2018

By Zhihe Dou, Jiang Liu, Ting-an ZHANG, Yukun Huang

The paper aimed to propose that mixed rare earth concentrate was decomposed by pressurized calcification where mechanical milling was applied simultaneously (also known as mechanochemical calcification). The bastnaesite and monazite were both decomposed by OH−, where released rare earth formed RE (OH)3, released fluorine and phosphorus formed CaF2 and Ca2P2O7. Then, the calcified slag was leached by diluted hydrochloric acid to extract rare earth and both recover fluorine and phosphorus. The phase transformation regularity, the behavioral trends of rare earth, fluorine and phosphorus were investigated. Results showed under the optimal conditions of ball to material weight 80:1, the calcification temperature 250 °C, the liquid-solid ratio 5:1, the leaching yield of rare earth reached to 92.16%, Ce was 86.47%, La was 97.58%, Nd was 99.99% and the mass fraction of F, P entering into calcified liquor were 8.27, 0.21% respectively. The micromorphology of the mineral has a transition from dense to fluffy, and then became dense again.

Mar 1, 2018

By Baohua Li, Yanhui Liu, Shengping Li, Xuewei Lv, Yun Chen

There are almost ten billion tons of vanadium-bearing titanomagnetite in Panzhihua-Xichang area. However, iron ores in Hongge, which has the most abundant reserves in the four mine areas in Panzhihua, have not been utilized sufficiently so far. The reason behind this is the relatively high Cr2O3 in the ores (0.49 %~0.82 %), that due to its high melting temperature will negatively influence the blast furnace reduction and slagging process. Therefore, in the blast furnace process, Cr is hope to be reduced into molten iron, which can reduce slag viscosity problems. Slag iron reduction experiments were conducted to quantify the Cr reduction. Experimental results shows that with the increase of TiO2, the content of Cr in the hot metal is decreased when balanced. And during the initial stage of the reduction reaction, the reaction kinetic model is a first-order reaction.

Jan 1, 2016

By R. Altman

A Brookfield viscometer fitted with a stainless steel bob was used to measure the viscosity of industrial lead blast furnace slags between 1126 and 1298°c. Slag oxidation state was characterized by first annealing the? slag samples at 750°c in sealed copper tubes in order to precipitate magnetite crystals. The magnetite concentration was then measured on an Outokumpu Saturated Magnetic Analyzer. Using an Arrhenius-type equation, a viscosity model was developed by regression. The equation below accounted for 75% of the variability in the data used to generate the regression coefficients and, on average, could predict viscosity within ± 12% of the measured value. The greatest difficulty encountered in measuring viscosity was due to the occasional presence of solids in the slag which caused, at times, erroneously high viscosity measurements. Precautions to minimize this problem are outlined in the text.

Jan 1, 1985

By Ademar B. Lugão, Sandra R. Scagliusi, Elizabeth C. L. Cardoso

When butyl rubbers are subjected to high energy radiation, they form easy free radicals that initiate various chemical reactions. These reactions alter the molecular distribution of irradiated rubbers by crosslinking or scission affect their physical and mechanical properties. This work aims to the analysis of effect induced by γ-exposure on the crosslinking density in butyl rubbers by swelling measurements accomplished before and after irradiation at 25, 50, 100 and 200 kGy, with further evaluation of crosslinking density accomplished by Flory-Rehner equation; this is a proper procedure for the qualification of radiation resistance. It can be noticed that changes in material structure was due to build-up of new three-dimensional network in studied rubbers. Changes in crosslinking density of butyl rubber compounds emphasize that degradation mechanism is strongly influenced by gamma-radiation doses higher than 50 kGy, since chain scission process predominates over crosslinking reaction.

Mar 1, 2017

By A. Kontopoulos

The Olympias Mine in Northern Greece is producing an extremely refractory gold-bearing arsenical pyrite concentrate, containing on the average 41 3 S, 40 3 Fe, 10-12 3 As, 25 ppm Au and 35 ppm Ag. During the process selection stage, more than a dozen alternative technologies? were considered and an in-depth analysis was prepared for the three most promising, ie roasting, pressure oxidation and biological oxidation. Detailed capital and operating cost estimates were prepared, based, where appropriate, on laboratory and pilot-plant tests. A number of criteria was used for process evaluation and selection, including capital and operating costs; environmental impact, gold' recovery, stage of development, etc. Based on the above evaluation, the Sherritt Pressure Oxidation Process was finally selected. A detailed description of the process selection stage, supported with laboratory and pilot-plant test results on many of the processes considered, will be? presented.

Jan 1, 1989

By Byung-Su Kim

Most electric arc furnace dust (EAFD) treatment processes employ carbon as a reducing agent for the zinc oxide in the EAFD. In the present work, the reduction reaction of zinc oxide with carbon in the present of various additives was studied. The effects of temperature and the additives of calcium carbonate, magnetite, and mill scale on the kinetics of the reduction reaction were measured in the temperature range of 1173 K - 1373 K under nitrogen atmosphere using a weight-loss technique. The mill scale is one of byproducts generated from the steel rolling process. From the experimental results, it was concluded that all three additives accelerates the reaction rate of zinc oxide with carbon, but the effect of addition of calcium carbonate is the highest. It was also found that magnetite, mill scale, and calcium carbonate in the reduction reaction of zinc oxide with carbon promotes the carbon gasification reaction.

Jan 1, 2006

By Jorge Alberto Soares Tenório, Romano Espinosa, Felipe Fardin Grillo, José Roberto de Oliveira, Denise Crocce

"The aim of this work was evaluation of the recovery of Zn and Fe of the EAFD added to the hot metal in the form of briquette at temperature of 1500°C. The EAFD was agglomerated by cold briquetting and introduced in the hot metal. This study utilized a bench-scale equipment to melt, during this process to kept a flow rate of inert gas above the bath. Were collected periodically metal samples and the samples were analyzed for determination of the content of total silicon and carbon by chemical analysis. Zinc oxide, zinc ferrite and other oxides were reduced and were volatized and collected by a cleaning system of dust (baghouse) located on top of the oven. More than 98% of iron were recovered from EAFD during the test. It was possible to produce a dust containing about 68% zinc by means of adding of EAFD.IntroductionIn the first semester of 2010, steel production was about 706 million tons, 27.9 % more than in the first half of 2009. Not a significantly increase if 2010 data is compared with the first semester of 2007 (only 7.2 % higher), before the world’s economic crises. Steel production is divided into two main routes. The first one, and most used, is the Basic Oxygen Furnace Process (BOF process), which in 2008 accounted for approximately 67.1 % of steel production. The second route is carried out in the Electric Arc Furnace (EAF) that in 2008 represented 30.6 % [1 ].Electric arc furnace dust (EAFD) is a solid waste generated during the steel making process. It is classi?ed according to NBR 10004 as dangerous solid waste-class I, because the elements Pb e Cd leach in water exceeding the maximum limits permitted by the NBR 10004 [2 ]."

Jan 1, 2012

By R. Steven Izatt

Green chemistry principles will be discussed, and examples will be given of the use of Molecular Recognition Technology (MRT) to selectively separate specialty metals such as cobalt, nickel, bismuth, rhenium, molybdenum, indium and germanium from various primary and secondary feed streams. Recovery of these metals has numerous advantages including (i) conservation of valuable resources, (ii) prevention of environmental damage, and (iii) elimination of capital and operating expenses due to re-processing or disposal of metal-bearing streams.

By Monica M. Jimenez Correa, Jorge A. Soares Tenorio, Denise Crocce Romano Espinosa, Paula Aliprandini

The surface zone of nickel laterite ore is generally considered as residue. However, because of the depletion of ore sources and the increase in demand, this previously discarded zone may now be processed economically for nickel and cobalt. After leaching and removal of the impurities, the solution contains cobalt, magnesium, manganese and nickel. Solvent extraction is a hydrometallurgical technique used in the separation of metals from aqueous solutions. Cyanex 272 and D2EHPA are extractants used to separate nickel from cobalt. The mixture of extractants can change the performance during the metals extraction. This work aims to evaluate the solvent extraction of nickel and cobalt when Cyanex 272 and D2EHPA are mixed. The results showed that the increased concentration of D2EHPA in the organic phase increased the extraction of nickel and magnesium. However, cobalt extraction was reduced and the manganese extraction was not altered.

Mar 1, 2018

By Guo Chen, Yifeng Shi, Xiaobiao Shang, Nanshang Shen, Bangqi Zhang, Jinhui Peng, Junruo Chen

"The energy is introduced directly into the volume of the honeycomb ceramic regenerator due to the complex interaction of microwaves with minerals in microwave gas heating system. A three-dimensional numerical model is developed to simulate the electromagnetic field by solving Maxwell's equations using finite-difference time-domain method. Computational result is presented for the microwave power absorption of the regenerator. Effects of the dielectric constant and the effective loss factor on the microwave power absorption in the regenerator are studied as well. Numerical results show that the heating pattern strongly depends on the dielectric property of the regenerator. The demonstration of the model of electromagnetic field distribution can be applied effectively and efficiently to optimize the fundamental parameters in the microwave heating processing.IntroductionIn recent years, microwave energy has been utilized in many fields, such as food processing, chemical engineering and mineral processing [l]. In contrast to conventional heating, where heat is transferred from a surface to the interior, microwave energy is introduced directly into the volume of minerals due to the complex interaction of the microwave with the mineral. Based on volumetric heating effects, microwave heating has several advantages such as pollution free, rapid heating technique, internal heating, high efficiency over conventional heating [ 1-4]."

Jan 1, 2013

By D. Y. Wang, G. Y. Sha, X. L. Shen, D. R. Gu

The study of the volatilization kinetics of zinc and lead in pellets made of zinc-leadbearing dust mixed with coal powder, in a nitrogen atmosphere and at a temperature range between 1100 °C and 1300 °C, shows that the reduction temperature has a significant effect on the volatilization rates of zinc and lead, and that both the particle size of the coal powder and the extra carbon content has no effect on the volatilization rates. The obtained activation energies for the volatilization of zinc and lead are 79.42kJ/mol and 88.74kJ/mol respectively. The volatilization rate of zinc is controlled by the reaction between the zinc oxide and carbon monoxide while that of lead is controlled by the lead evaporation reaction, and the diffusion of gaseous lead through the gas boundary layer covering the surface of the reduced liquid lead.

Jan 1, 2000