Search Documents

By Sharif Jahanshahi

Calcium ferrite slags are often associated with Professor Yazawa due to his pioneering work on the thermodynamics of this type of melts. Over the past years CSIRO has invested some effort in studying physico-chemical properties of such melts to fill in some gaps in our knowledge and explore opportunities for application of the understanding developed. These investigations cover thermodynamics, transport properties of calcium ferrite based slags, as well as the kinetics of reactions of such slags with refractories. The present paper provides an overview of some of these studies and highlights some of the interesting behavior of such melts. The oxidation state of copper and arsenic in calcium ferrite based slags are predominantly Cu+ and As3+, respectively, at oxygen potentials below 10.1 atm. The concentration ofCu2+ in such slags becomes significant at oxygen potentials of greater than 10'1 atm at 1300 ?C. The activities of CuOo.s and AsOl.S in calcium ferrite slags show strong deviations from the Raoultian Law, while that of CoO is very close to ideal behaviour with respect to pure solid CoO. Addition of Si02 to calcium ferrite slags can have significant effects on the activities of FeO and Fe2O3 and hence the stability of magnetite phase. Transfer of oxygen in calcium ferrite slags is fast with diffusivity of 2xlO?3 cm2/s at 1350 °C and activation energy of 16 kcal/mol Presence of solid phases, such as magnetite, has pronounced effect on the viscosity of calcium ferrite slags. The observed dependence on solid loading and shear rate indicates deviation from Newtonian behaviour. The interfacial tension between copper mattes and calcium ferrite slags is strongly dependent on the matte grade, with the determined values being much lower than the corresponding ones for interfacial tension between similar mattes and iron silicate slags. MgO, Cr2O3 and MgCr2O4 have low solubility in calcium ferrite slags and their solubility increases with increasing copper oxide content of the slag at 1300 °c. The oxidation state of the slag has strong effects on phase transformation, dissolution rate and disintegration of refractories in calcium ferrite slags. Other key factors with major impact on slag-refractory interactions include viscosity and surface tension of slags as well as the contact angle between slag and refractory material.

Jan 1, 2003

By A. E. M. Warner

Inco Limited has long and extensive experience in converting nickel-copper primary smelting mattes over a broad range of nickel/copper weight ratios and combined nickel-copper-cobalt contents. At the Copper Cliff Smelter, the composition of the converter product matte has to meet the requirements of the matte separation process; at the Thompson Smelter, converter matte of a different composition is cast into anodes for nickel electrorefining; and in Soroako, Indonesia, a very low copper product matte is granulated for the Japanese market. Recently, Inco has conducted pilot plant testing of three possible nickel-copper matte continuous converting routes, namely flash converting, oxygen top blowing-nitrogen bottom stirring, and tuyere blowing. This test work has generated substantial new information on nickel-copper matte converting chemistry. This overview paper reviews the metallurgy of nickel-copper matte converting, in particular the behaviour of cobalt and the operating conditions required to meet the iron and sulfur specifications of the product matte. The relevant thermodynamic information is used to discuss the industrial data.

Jan 1, 2003

By Denise Crocce Romano Espinosa, Andrea Moura Bemardes, Jorge Alberto Soares Tenorio, Daniella Cardoso Buzzi, Tatiana Scarazzato

"In copper plating processes, a fraction of raw materials are incorporated to the final products, while other portions are discarded as effluents. In this study, the application of electrodialysis (a membrane treatment process) was studied for treatment of wastewaters from cyanide-free strike baths, in order to reuse the components of this bath: copper and HEDP. The synthetic solutions studied consider 1 % of ion concentration of the bath used in this process, simulating the rinsing waters to be discarded. The electrodialysis allowed a percentage extraction up to 73% of copper ions and 72% of HEDP from the effluent. Complexes formation between the acid and copper indicates the possibility of recovery of components in the same compartment, obtaining a concentrated solution of these substances that can be reinserted in the process, for compensating drag-out losses. A diluted solution is also obtained, that can be reused as water in rinsing tanks.IntroductionIn metal finishing industries, contaminants in wastewater and the type of treatment required are determined according to the type of operation [l]. Generally, electroplating industries employ conventional wastewater treatments, e.g. oxidation of cyanide and chemical precipitation. This stage promotes reactions with soluble compounds to produce an insoluble precipitate, removed by physical separation. The sludge is dried by press-type filters [2].In this manufacturing sector, part of the raw materials are discarded as hazardous waste. The cost of discarded compounds and the treatment and disposal of waste may compromise profit margins. In addition, water consumption per unit of production stimulates the development of methods able to recover and reuse the largest possible amount of water [3].In some plating processes, cyanide-based substances are used as complexing agents and as raw materials in form of metal salts [4]. However, the toxicity associated with cyanide has been promoting research for the development of new raw materials in plating processes.A study conducted in Brazil [4] evaluated the modification of a commercial cyanide-free bath for processes of copper coating on Zamak. In the performed study, a new alkaline copper bath was formulated using l,hydroxyethane-1,1-diphosphonic acid (HEDP), an organic compound known for forming stable complexes with metal ions.As results of the study, the operational conditions and the formulation of a bath to obtain adherent, uniform and bright layers were established (Table I) [4]."

Jan 1, 2014

By George Grandy

Kvaerner experience is being used to develop software to design or simulate crushing and screening plants. The model techniques discussed are presently being used for open-circuit plants and are being extended to closed circuit plants. The program contains a library of routines, each representing a piece of equipment or unit operation, which are assembled into one of several open-circuit plant configurations. Routines include gyratory primary crushers; standard secondary and shorthead tertiary cone crushers; single, double or triple deck screens; and stockpiles, feed bins and belt conveyors. The program uses steady-state models to simulate the performance of crushers and screens that have small residence times and quickly reach equilibrium when operating conditions and/or parameters are changed. The dynamic aspect of the total circuit model concerns the storage units within the circuit, i.e. stockpiles and bins, and, in the closed circuit configuration, circulating loads and size distributions. In many cases, just vendor's catalog data are necessary for a pre-feasibility simulation; in other cases, actual plant test data are required to obtain more accurate simulations. The entire plant is shown in a single graphic screen so the user can see all the relevant information he might want, and soft-keys are provided for the user to make on- line parameter changes and observe the effects on storage elements, equipment feed rates and the final product size distributions. The model also reports equipment utilization in percentage, power consumption, and other related operating information, and soon, will be able to report estimated capital and operating costs.

Jan 1, 1999

By Husamuddin Ahmadzai

A survey of regulations and state of the art control technologies is presented relating to the smelting of primary aluminium, copper and recycling of residues. Some costs associated with the alternatives and trends for the coming decade in this. sector are identified.

Jan 1, 1992

By Behrouz Abedian, Livia M. Racz

"We address dynamic interactions between high-energy, reactive surfaces of polymer-matrix composites and solid surfaces. A common characteristic of these interfaces is that bonding occurs readily upon contact. In many industrial and biomedical applications, it is desirable to suppress this bonding phenomenon. This interfacial effect is discussed in light of the development of our new method of handling polymer-matrix composites in dental applications. This method involves vibration of the solid-polymer interface at different frequencies. For each material, there is a critical frequency at which the sum of the viscoelastic and inertial energies of the fluid at the surface exceeds the energy available for bonding. When the polymer is vibrated at or beyond this frequency, it does not adhere to solid surfaces. An important aspect of the developed process is that it can be used to characterize surface and interfacial properties of polymers under dynamic conditions, whereas existing techniques are restricted to the study of bulk dynamic properties.IntroductionThe purpose of this paper is to report on the development of a new method for manipulating polymer-matrix composite materials used in dental applications, and the potential of this process for use in materials characterization. The materials under discussion have polymer matrices of a combination of bisphenol A-glycidyl methacrylate (BIS-GMA) and triethylene glycol dimethacrylate (TEGDMA), and contain filler particles of silica and/or zirconia glasses. These materials are called direct aesthetic restorative materials, and are used for filling of cavities, repairing chipped teeth, and for other restorations in which appearance is of importance. They have the appearance of natural tooth material, and are therefore in great demand for use in the anterior portion of the mouth(l,2)."

Jan 1, 1998

By Yuri Gelfgat

"This paper presents some results of the investigation of the steady magnetic field influence on hydrodynamics and heat/mass transfer in processes of semiconductor single crystal growth (Si, Ge, InSn). The investigation employed mathematical and physical simulation techniques of relevant processes and full-scale experiments on growth facilities. A number of additional MHD phenomena have been found generated in the melt due to the rearrangement of flow pattern, the formation of specific convective cells, and the origin of MHD boundary and shift layer.IntroductionMagnetohydrodynamic (MHD) means of creating forces by contact-free methods in liquid conducting media have been widely used in the production of volume semiconducting single crystals. The goal of this method is to control convective transfer processes in the melt volume and on the crystallization front [1-3]. This is due to the sufficiently high conductivity of semiconductor melts (s = 104 /106 O1m-1 ) and an obvious relationship between the hydrodynamics in the melt and at interfaces and the conditions of formation of single crystals and their quality [ 1].All types of MHD effects rest upon the generation of volume electromagnetic forces in the melt by various means as well as on the possibility to direct them arbitrary in space and to adjust easily their absolute values. Fig. l presents different means how to implement MHD phenomena during single crystal growth. It should be emphasized that in all the modifications given in Fig. l additional energy introduced into the melt cannot influence directly the crystallization process since it is incomparable to the energy of molecular forces. Both the influence and efficiency of MHD means are determined solely by the change of motion, heat and mass transfer characteristics."

Jan 1, 1998

By Hongbo Zhao, Jun Wang, Wenqing Qin, Guanzhou Qiu, Xueduan Liu

Bio-hydrometallurgy technology was applied for the extraction of copper from the raw ores of Chambishi Mine in Zambia. A copper extraction of 93.29% was obtained for small scale column bioleaching within 63 days, while a copper extraction of 89.05% was achieved for large scale column bioleaching in 90 days, thus confirming the amenability of the raw ores for effective extraction via bioleaching. The bacteria were cultured in a 6-stage enlarge cultivation. The bacterial cultures with cell concentration of more than 1×108 cells/mL were added into a spray pond of sulfuric acid to be applied in the dump leaching, and a copper extraction of about 50% was achieved within 2 months. The production report revealed that the copper extraction increased by approximate 20%, and the acid consumption was reduced to around 35% as a consequence of adding the bacteria. The industrial demonstration of the bio-hydrometallurgy technique is now well established in Zambia, and further applications of bio-hydrometallurgy in both Zambia and Congo are currently in progress.

Jan 1, 2015

By Pesic. Batric

A novel chitosan-pyridoxal-epichlorohydrin was synthesized and evaluated in our laboratories. The evaluation was achieved by performing kinetic and equilibrium studies of copper sorption. The parameters examined were pH, temperature, concentration of copper, particle size and selectivity of copper sorption against iron, zinc, cadmium and cobalt. It was found that pH was the most important parameter, and sorption of copper increased with pH increase in the range pH 2.5-6.0. The low activation energy of the sorption reaction, 1 1.13 kJ/mole (2.66 Kcal/mole), showed that temperature was not an important parameter. The synthesized chitosan was selective against iron, zinc, cadmium and cobalt. The selectivity with respect to last three metals was achieved by the kinetic difference of sorption, as sorption of copper was much faster than for other metals. Iron (Fe2+) does not adsorb on chitosan. The mechanism governing the sorption of copper is intraparticle diffusion. This finding was supported by the dependance of copper sorption on the square root of time, the low activation energy, and the fit of experimental data in the diffusion through the product layer equation.

Jan 1, 1994

By Hu Long

Pyrite, as the host mineral in refractory gold ores and concentrates, has been treated by pressure oxidation in sulfuric acid solutions at temperatures above 180°C to liberate gold prior to cyanidation since the 1980's. However, no data is available on the kinetics of pyrite during acid pressure oxidation over the temperature range of 180 to 230°C which is the range employed by most commercial plants. The dissolution of pyrite (FeS,) in sulfuric acid solution under oxygen pressure was investigated at temperatures ranging from 170 to 230°C. The effects of temperature, particle size, agitation speed, oxygen partial pressure, and pulp density were evaluated. The effects of foreign ion addition and the concentration of sulfuric acid were also examined. The apparent activation energy was estimated to be 42.6 kJ/mol in the temperature range 170 to 230°C. The reaction orders with respect to particle size and oxygen partial pressure were found to be -1.5 and 0.5 at 210°C, respectively. Experimental evidence suggests that the kinetics are limited by the surface chemical reaction initially, and then also to some extent by the diffusion of ferrous ions away from the particle surface.

Jan 1, 1999

By T. Wang, R. G. Reddy

"A new eutectic of LiNO3-NaNO3-KNO3 ternary system was calculated by using thermodynamic modeling and the eutectic temperature was predicted to be 389.15K. The melting point was determined using Differential Scanning Calorimetry (DSC). On repeated measurements, it was found that the melting point of the eutectic composition showed excellent reproducibility with the predicted value. The heat capacity was also measured using DSC and the data as function of temperature were fit to polynomial functions. Subsequently, the thermodynamic properties such as enthalpy, entropy and Gibbs energies of this novel ternary eutectic salt mixture were deduced as function of temperature.IntroductionIn these days, the provision of the large amount of energy required in the peak period relies more and more on the parabolic trough solar power plant and it works by utilizing the thermal transfer fluid. Consequently, the development of inoovative thermal transfer fluid with higher energy storage density is paramount to lower the expense for generating energy [1-4]."

Jan 1, 2013

By Sesha S. Srinivasan

Mechanochemical synthesis has been employed to prepare new light weight complex borohydrides, Zn(BH4)2. The thermal calorimetric and gravimetric analysis of these complex borohydrides shows the hydrogen decomposition temperature (Tdec) of about 100° C with theoretical capacity of ~8.0 wt%. This advanced materials based technology is considered to be suitable for attaining the US-DOE grand challenge technical targets. The powder x-ray diffraction analysis of the mechanically milled Zn(BH4)2 exhibits the presence of zinc borate and NaCl phase. The FTIR spectra of BH4-ion in NaBH4 has a characteristic band at 2290 cm-1,whereas in Zn(BH4)2, it occurs at ~2061 cm-1 (bridging B-H bonds) and ~2451 cm-1 (terminal B-H bonds) as well. The reversibility of hydrogen decomposition and recombination process is carried out by PCT measurements with multi-cycling procedure.

Jan 1, 2006

By Alan J. Hurd

"New insights into the development of microstructure in sol-gel films have recently been revealed by several diagnostic techniques, including imaging ellipsometry, ""chemical imaging"" by fluorescent tracers, light scattering from capillary waves, and finite-element modeling. The evolution of porosity during the continuous transition from dilute sol to porous solid in restricted geometries such as films and fibers is becoming clearer through fundamental understanding of evaporation dynamics and capillarity.IntroductionWith sol-gel processing, the full flexibility of solution chemistry can be exploited to make ceramic films and fibers with well controlled compositional characteristics. No less important is the ability to tune porosity and connectivity for specific applications such as optical and electrical coatings and membranes. Since the chemical and physical factors that determine the microstructure are not entirely understood, new diagnostics applied to sol-gel processing are welcome.Sol-gel films and fibers are distinguished by processing that takes a sol through continuous stages of increasing concentration and connectivity of a solid precursor. The liquid carrier is usually volatile or, at least, volatilizable through heat treatment. During deposition through states of increasing solids concentration, this sol might gel, as in bulk sol-gel processing, however, the gel state may be a fleeting transient that quickly empties of liquid. Nevertheless, the structures formed in solution during this stage influence the structure of the final solid. In particular, porosity is likely to be a remnant of networks formed in the sol-to-gel transition. Here we report on experiments whose goal is to discover the factors involved with porosity development."

Jan 1, 1994

By Bengt T. Andersson

Outokumpu Consulting Engineers, Outokumpu Oy SF-02200 Espoo 20, Finland This paper describes experiences from some operating non-ferrous flash -smelters and focuses on the advances in smelter byproduct and gas treatment engineering design. In this context a summary is given of the specific technical and economic benefits achieved-by flash -smelting technology and oxygen enrichment. The paper will also briefly outline a few new process and equipment developments.

Jan 1, 1983

By Shekhar Bhansali, Shyam Aravamudhan

"This paper reports on the design and simulation results of a silicon bulk-micromachined diaphragm-type piezoresistive pressure sensor capable of operating linearly over a wide dynamic range (0-1000 meters of water). The piezoresistor elements of the sensor are arranged in a wheat stone bridge configuration to achieve a higher output response. Simulation results (output voltage and sensitivity analysis) obtained using coupled MemPZR-MemMech module of the CoventorWare2003 Finite Element tool are presented. The effect of diaphragm size, diaphragm thickness and thickness of the piezos on output sensitivity were analyzed and optimized to get a linear response over the wide dynamic range.IntroductionThe physical and biological processes in the ocean are critically influenced by ocean parameters (pressure, salinity and temperature). Thus there is a need to develop inexpensive and reliable sensors to continuously measure large volumes of sea-space over long time spans. A key component in any such system will be a pressure/depth sensor. This sensor is routinely employed in marine applications such as wave and tide gauges, tsunami detection, platform leveling etc. More significantly, pressure measurement is needed for depth determination. Depth sensors are vital for remote operated vehicles (ROVs), profiling instruments and towed arrays.Several techniques have been routinely used in the past to measure pressure in the marine environment [1-3]. In general, the pressure sensor design is based on a flexible membrane as the spring element for the sensing pressure [4]. The deflection of the membrane, induced by the applied pressure, is converted into an electrical output through a component that is sensitive to diaphragm deflection (capacitive coupling) or associated stresses (piezoresistors, strain gauges). The temperature compensated pressure measurement can be readily converted to depth using"

Jan 1, 2004

By R. A. Alock

The character, occurrence and genesis of the three types of nickel deposits, sulfide, laterite and deep-sea nodule are described, highlighting the differences in mineralogy and chemical composition that effect the extractive metallurgy of nickel and associated byproducts. World nickel production and current resources by deposit type and geographic location are also reviewed.

Jan 1, 1988

By Paul B. Queneau

U.S. plants solely devoted to recovering values from metal-rich wastes have established market niches based on one or more competitive advantages: superior process technology, access to key feedstocks, unique equipment, special knowledge of markets, and an appropriate exit for outfall water. Plant methodology, competitiveness, environmental factors, and economics are examined, with particular attention to feedstocks, technologies, products, and outputs.

Jan 1, 2003

By Patrick R. Taylor

Glass is used for immobilization of radioactive and hazardous wastes due to its durability and ability to accept a variety of waste constituents into its network structure. Alternative high temperature vitrification techniques have the advantage of increased throughput, increased waste loading and being applicable to variable and heterogeneous waste streams. However, the increased processing temperature places further concerns on the increased volatilization of contaminants, and increased corrosion and erosion of me Iter components. A database of melt properties at higher temperatures, such as partitioning, viscosity, density and electrical conductivity, in the temperature range of 1400-20000 K are being developed.

Jan 1, 2000

By James E. Simpson, Suresh V. Garimella, III de Groh

"An experimental and numerical study of the horizontal Bridgman growth of pure succinonitrile (SCN) and of a succinonitrile-1.0 mol. % acetone alloy (SCN-1.0 mol. % ACE) has been performed. Experiments at growth rates of 0, 2 and 40 µmis were investigated. The solid/liquid interface was stable (non-dendritic and non-cellular); however, it was not flat. Rather, it was significantly distorted by the influence of convection in the melt and, for the growth cases, by the moving temperature boundary conditions along the ampoule. For the alloy, the interface was determined to be unstable at growth rates greater than 2.8 µmis, but stable for the no-growth and 2 µmis growth cases. When compared to the pure SCN interface, the alloy interface forms closer to the cold zone,· indicating that the melting temperature has been suppressed by the addition of the alloying element. Two-dimensional computer simulations were performed for the no-growth case for both the pure and alloy materials. These simulations indicate that a primary longitudinal convective cell is formed in the melt. The maximum magnitude of velocity was calculated to be 1.515 mmls for pure SCN and 1. 724 mm/s for the alloy. The interface shape predicted by the computer simulation agrees well with the experimentally determined shape for the pure SCN case. In ongoing work, numerical simulations of the process during growth conditions are being performed.IntroductionIncreasingly, advanced materials used in the aerospace, automotive, optics and electronics fields require low levels of defects and high levels of solute uniformity. Directional solidification by the Bridgman process is widely used for synthesis of these high-quality materials. During Bridgman crystal growth, heat and mass transfer by both thermal and solutal gradient-driven convection and diffusion influence the shape of the solid/liquid interface and dopant segregation levels, and hence, directly determine the final crystal quality. Key process parameters include the applied furnace temperature distribution and rate of translation, ampoule properties and furnace orientation."

Jan 1, 1999

By J. Phillip Mackey

The Peter Hayes Symposium on Pyrometallurgy, held as part of Extraction 2018, is an acknowledgement of his contributions to the basic science and principles underpinning modern pyrometallurgical processing. After completing his PhD at Strathclyde University, Scotland, in 1974, Peter took up a teaching position at The University of Queensland, Brisbane, Queensland, Australia in 1976. Peter Hayes’ research at the University since then has been focussed on: • The mechanisms and kinetics of heterogeneous solid/solid, gas/solid and liquid/ solid reactions, and • Experimental measurement of phase equilibria in complex high temperature metallurgical systems. This paper provides a brief biography of Dr. Peter Hayes and gives a full listing of Peter Hayes’ publications.