Search Documents

By Leigh J. Wardle

Significant coal reserves in New South Wales lie under areas with steep topography such as valley slopes and cliffs. Subsidence predictions are difficult to make for these locations as existing empirical databases cannot cover all permutations of topography and mining geometry. Two dimensional numerical model alternatives are of limited applicability. Consequently a novel three-dimensional numerical model is developed including the detailed panel layout, realistic rock mass properties including the full stratigraphy, goat behaviour and actual surface topography. Model results show the same trends as subsidence measurements from Baal Bone Colliery in the Western Coalfield of New South Wales

Jan 1, 1992

By S. Paul Singh

The implications of blast damage are harmful in both economic and physical sense. To understand the mysterious nature of blast damage assessment and prediction, field work was done by driving an experimental tunnel in the bench of a quartzite quarry. On the basis of the blast vibration monitoring records, a model was developed to predict the PPV at different distances from a blasthole. Critical particle velocity for damage and the output of the prediction model were used to delineate the extent of damage for different explosives. The predictory model was tested by designing a special blast and the burdens for the back holes have been recommended. The relationship between the critical particle velocity for "Fall Off' and the critical particle velocity for damage has been established. The existing criteria for blast damage have also been renewed in this paper.

Jan 1, 1993

By M. Zaki Rashad

In this paper, if three slant distances are measured from three given points of known coordinates to an unknown point, the position of this point (X, Y, and Z coordinates) can be determined. A computer program was designed for observing the movement of a point in the roof in Abu-Tartour mine (western desert, Egypt) to measure the convergence. This method, for general using, is very fast and can be applied without any restrictions.

Jan 1, 1990

By Kent D. Mctyer

Mining commenced at Tasman Mine in late 2006. The current method of mining is bord and pillar using continuous minerbolters and shuttle cars for first workings and secondary extraction using mobile roof supports. The two stage process was chosen to accommodate irregularly shaped coal deposits, allowing adjustments to be made to extraction ratios for better management of subsidence and to maximize the efficiency of the operation. Following the completion of the first three full/partial extraction panels, the mining method was changed due to variable caving. Another partial extraction method, referred to as the Duncan Method was adopted; it involves stripping the developed square pillars on four-sides on retreat to leave a load-bearing remnant coal pillar. The system of partial extraction has been successful in meeting safety, productivity, and subsidence targets.

Jan 1, 2011

By Dennis Dolinar

"Tailgate entries in U.S. longwalls can be subjected to high loads and deformations. Therefore, tailgate entries are generally supported with varying types and amounts of standing support. However, even with standing support, roof falls and blockages can occur in the tailgate when the support system is not properly designed. Safe and efficient operation of a longwall face requires the selection of the appropriate type and amount of standing support. Because of the importance of maintaining a safe and functional tailgate entry, the National Institute for Occupational Safety and Health (NIOSH) is currently developing a standing support design methodology based on the ground reaction curve. Using the ground reaction curve for design requires that the ground and support interaction be quantified. This can be accomplished by the installation and analysis of data from instrumented field sites. Although necessary, the field results cannot develop the complete ground reaction curve. Numerical models, calibrated to the field results, are used to establish the complete ground reaction curve. In the present study, data was obtained and evaluated to establish points for calibration of the ground reaction curve for two western longwall operations.One test site, Mine A, was located at a depth of 1,550 ft. At this site, the floor consisted of siltstone, while the roof was an interbedded siltstone and sandstone. Because of the depth, a double row of22-in diameter CANs1 were installed to support the tailgate. Both the first and second longwall panels have mined past the instrumented site.The second site in Mine B is at a depth of only 760 ft. The floor at this mine consists of a weak shale/mudstone and the roof consists of thick, top coal overlain by weak shales. At this site, a double row of pumpable cementitious cribs was installed. The second test site has only been subjected to side abutment loading from first panel longwall mining.The measurements indicate that the support at both mines was heavily loaded when subjected to the side abutment loading from first panel mining. At the deeper site, the support began to yield when the face was more than 300 ft outby during second panel mining. In comparison to results from previous test sites in the Pittsburgh Seam and Illinois Basin, the amount of support loading and roof-to-floor convergence was an order of magnitude higher at the western sites. This has resulted in a significant difference in the position and shape of the ground reaction curves."

Jan 1, 2010

By Liu Changyou

This paper analyzes experimentally the stress-strain relationship and the characteristics and variation trends of acoustic emission signals of the medium- and high-burst-prone coal/rock fracture process. The precursor and sensitive characteristics of the acoustic emissions when the burst-prone coal/rock fracture occurs were obtained. The characteristic index and the feasibility for predicting rock bursts using acoustic emissions technology were proposed. Keywords: burst-prone coal/rock, acoustic emissions, energy, prediction index

Jan 1, 2003

By Jesse Puller, Ken W. Mills, Owen Salisbury

"An underground coal mine located in New South Wales has a target coal seam located 160-180 m deep directly below a 16-20 m thick conglomerate unit that has been associated with significant periodic weighting events on the longwall face. As part of the investigations to better understand the causes of periodic weighting at the mine, inclinometers capable of measuring horizontal shear movements through the full section of the overburden strata were installed ahead of mining at two locations approximately 1 km apart above the centre of two longwall panels. These inclinometers were monitored as the longwall approached each site. This paper presents the details of the installation, the results of the inclinometer monitoring at both sites, and the insights that these measurements provide for overburden behaviour about longwall panels.Horizontal shear movements were observed to develop on shear horizons that correlate closely across the two sites suggesting a mechanism that is consistent across a large area of the mine. Shear movements were observed to develop on a single horizon near the top of the conglomerate strata that was mobilised almost immediately after initial formation of the longwall goaf at a distance of 425 m ahead of the longwall face. The direction of horizontal movement was consistent with the relief of the major principal horizontal stress. As the longwall face approached each inclinometer, other horizons within the upper part of the overburden strata begin to shear with the upper strata moving toward the approaching goaf more than the lower strata. Within the last 30 m of longwall approach, tilting of the strata associated with the increase in vertical subsidence toward the extracted goaf caused a change in the style of deformation with tilting and reverse shear offsets.INTRODUCTIONLongwall mining is recognised from subsidence monitoring, surface extensometer measurements, and various other observations to cause significant disturbance to the overburden strata directly above the extracted goaf of each longwall panel. Disturbance to the overburden strata beyond the limits of each longwall panel is not so well understood. Subsidence monitoring indicates that horizontal movements beyond the edges of the extracted longwall panel are generally greater in magnitude than vertical subsidence and horizontal movements may extend up to several kilometres from the edge of the panel in some circumstances (Reid 1998, Reid 2001, Hebblewhite et al 2000, Mills 2001, Mills 2014). The mechanics of how these movements are accommodated within the overburden strata is only poorly understood and there are few direct measurements."

Jan 1, 2015

By C. W. Bollier

In recent years, Peabody Coal Company has enjoyed a great amount of success using roof trussing as a secondary support system. Since 1975, over 180,000 trusses have been installed in 12 different Peabody mines with varying geological conditions. Projections from Peabody, and throughout the mining industry, indicate a continuous growth in the trussing principle for roof control. Peabody's primary supplier has sold over 1,000,000 trusses to 50 different mines throughout the country. (1) Roof trusses provide an improved means of controlling difficult roof conditions which, in turn, improves worker safety and mine production. Since the original development of the truss, (2) the only major modification to the trussing procedure has been the addition of the resin point anchor system in the mid-70's. The resin point anchor was the catalyst needed to provide a reliable anchor and create acceptance of the roof truss by both management and labor. Peabody began using trusses in their mines in 1975. For the first few years, most of the truss effort was geared toward determining proper anchorage, spacing, and gathering historical data. In recent years, Peabody's activities have centered on the development of improving trussing procedures. Through monitoring and trussing activities, a number of areas of improvement have been found.

Jan 1, 1982

By David Hill

Over the last decade, Beltana No.1 Mine has generally been Australia?s most productive longwall operation, with a ROM output of 7.2 Mt in YEJ2007. Characteristically favorable roof conditions and low depths of cover resulted in typically high rates of development drivage and longwall retreat. As a consequence of these high rates of development and extraction, there was a continuing focus on recovering and relocating the longwall face as efficiently as possible to minimize associated production delays and operational costs. This paper presents a comprehensive case study of the conventional longwall recoveries (?take-offs?) at the mine, from Longwall 1 to 14. By examining the take-off monitoring data collected over the life of the mine, the key geotechnical issues are demonstrated, including their relationship to the ground behavior experienced and the issues overcome.

Jan 1, 2011

By Yingxin Zhou

Data from these field studies and previous case study data have been combined to define ultra-dose seam mining environments and relate them to observed failure conditions. A rating system for ultra-close multi- seam design has been developed and field studies have verified the applicability of the design criteria according to geologic structures, lithology and spatial data. This rating system has been combined with design and depth considerations to create a protocol for quantitatively predicting potential damage in ultra-dose seam mining conditions. A brief discussion of the characteristics of ultra-dose seam mining and its related failure mechanisms is also presented

Jan 1, 1990

By Bo-Hyun Kim, Steve Berry, Mark K. Larson

"When coal pillar bursts occur, they involve the sudden expulsion of coal and rock into the mine opening. These events occur when relatively high stresses in a coal pillar, which serve as support in underground workings, exceed the critical capability of the pillar. This causes the pillar to rupture without warning. A cleating is a type of naturally occurring joint system unique to coal seams. However, cleatings are pervasive throughout the coal seam and are much more tightly spaced than joints occurring in other rock types. In this study, researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated 84 coal samples obtained from a Utah coal mine by conducting both unconfined and triaxial compressive tests in order to examine the response to stress as a function of both confinement and orientation between cleat and loading direction. The results of the study show that the confining pressure dictated not only the peak compressive strength but also the brittleness as a function of the major-to-minor principal stress ratio. The spalling limit of the coal estimated by the s-shaped brittle failure criterion appears to be very dependent on the angle between the cleat and the loading direction, particularly at lower confinement.INTRODUCTIONCoal pillar bursts, or bumps, remain a most critical safety concern in underground coal mining, despite significant advancements in engineering controls. As shown in Figure 1, between 1983 and 2014, there were nearly 400 cases of reportable dynamic failure accidents in coal and nonmetal mines, resulting in 20 fatalities, 155 lost-time accidents, and an estimated 48,000 lost man hours (MSHA, 2015). These types of events have been documented for well over 100 years within the American underground coal mining industry. During this time, mining practices and support technologies have evolved considerably, resulting in an overall decrease in the rate of dynamic failure-related injuries and fatalities. Although techniques and practices of mining are highly advanced, coal pillar bursts, or bumps, continue to occur (Mark and Gauna, 2015). If coal is expected to fail in a brittle manner, behavior changes associated with relatively low tensile strength, such as the transition from tensile to shear failure, have to be considered and reflected in the adopted failure criteria. Rock failure in tension takes place at low confinement around excavations due to tensile failure in heterogeneous rocks (Diederichs, 2007). The prospect of tensile-dominant brittle failure diminishes as the confinement increases away from the excavation boundary. Therefore, it is expected that the transition from tensile to shear mode in the failure mechanism occurs as the confinement level changes and conditions for tensile failure are prevented or strongly diminished. In addition, many uncertainties remain because of the highly anisotropic characteristics of coal seams associated with geologic structure and the mining-induced spatial redistribution of stress in coal pillars. Thus, to prevent fatalities in underground coal mining, continuous effort is required to better understand the catastrophic failure mechanisms in coal mines."

Jan 1, 2018

By Ezzeddin Bakhtavar

There are several geotechnical challenges and risks inherent in the interaction between the open-pit and block cave mining environments. This is especially true when they have to work simultaneously for a short time, as well as when only the caving operation is continued. Some of these challenges and risks include the induced zones of stress due to the large and deep open-pit, instability of the slope, instability of the crown pillar and water inflows, subsidence, and sometimes instability of the main accesses to the block cave portion of the mine. These challenges usually occur due to cave propagation. In this paper, these geotechnical challenges and associated risks have been studied and discussed. It was concluded that the majority of the mentioned geotechnical risks could be decreased, and often eliminated, by considering the appropriate dimensions of a stable crown pillar, especially in simultaneously working open-pit and block caving operations.

Jan 1, 2011

By Douglas Tesarik, Mark K. Larson, Habte Abraham, Heather E. Lawson

Dynamic failures, or "bumps", remain an imperative safety concern in underground coal mining, despite significant advancements in engineering controls. While many factors have been empirically linked to the occurrence of dynamic failure events, identifying a consistent, repeatable set of criteria within a field setting has proven elusive; conditions generally associated with dynamic failure might produce an event at one site, but not another. Conversely and more troubling, dynamic failure could occur where relatively few of these factors exist. The presence of spatially discrete, stiff roof units, such as paleo channels, are one such feature that has been linked to the occurrence of dynamic failure events. However, an empirical stratigraphic review investigating the relative frequency of discrete units in bumping versus non-bumping deposits indicates that no significant difference exists based on this criterion alone, and that instead an apparent relationship exists between reportable bump history and the overall character of the host rock with respect to stiffness. Due to the complexity of the bump problem, however, these results are not conclusive, as they do not take into account any variable other than the presence or absence of stiff members in the roof lithology; To weight the relative impact of changes in a single variable, such as the thickness or location of sandstone members, it must be examined in isolation-i.e. in a setting where all other variables are held constant. Numerical modelling provides this setting, and the effects of variability in a stiff discrete member in a hypothetical longwall mining scenario are investigated within the context of three stratigraphic "types'', as determined by the ratio of stiff to compliant stratigraphic members; Compliant, Intermediate and Stiff A modelling experiment examines changes in rupture potential in stiff roof units for each stratigraphic type as discrete unit thickness and location are manipulated through a range of values. Results suggest that the stiff-to-compliant ratio of the host rock has an impact on the relative stress-inducing effects of discrete stiff members. In other words, it is necessary to consider both the thickness and the distance to the seam, within the context of the host rock, to accurately anticipate areas of elevated rupture induced hazard; acknowledging the presence of a discrete unit within the overburden in general terms is an insufficient indicator of risk. Through modelling of anticipated changes in the placement and dimensions of discrete units within their stratigraphic setting, elevated rupture-induced bump hazard can be anticipated on a case by case basis. Were similar modelling studies conducted at mine sites in tandem with tracking of problematic discrete stiff units, areas of elevated rupture risk could be anticipated in advance of mining. Developing this predictive capability beyond identifying rupture potential in discrete roof members is essential to the eventual elimination of dynamic failure related worker injuries and fatalities. As stress is a necessary component in the occurrence of dynamic failure events, this finding helps to refine our understanding of the role of individual stiff, strong roof members in bumping phenomena, and suggests that a more holistic view of overburden lithology, combined with site-specific numerical modelling, may be necessary to achieve greater miner safety.

Jan 1, 2016

By Andrew P. Schissler

Cyprus Shoshone is an underground coal mine in southern Wyoming owned by Cyprus Coal Company, a subsidiary of Cyprus Minerals Company. To date, seven longwall panels have been extracted from the pitching seam under increasing depth of cover from 150 ft to 1200 ft. The purpose of this paper is to describe the geology, rock mechanics needs identification, design, testing and successful application of the current headgate/tailgate cribbing system. The immediate roof of the Shoshone is unique in that the first 50 ft of lithology is interbedded mudstones. The mudstone is slickensided, highly friable and has characteristics of unconsolidated fill relative to self-spanning and beaming abilities. Finite element modelling analysis of the overall geomechanical environment showed the mudstone to yield under applied longwall abutment stress. Roof bolt system design methodology also pinpointed the relative weakness of the mudstone roof. In-mine entry vertical convergence and weight response from the mudstone identified the need to design a crib which had superior weight capacity over a wide range of convergence. Design of a structure ensued to achieve the superior strength properties of wood parallel to the grain and the displacement properties of wood perpendicular to the grain. Testing of the prototype structure along with other alternative wooden cribs was done at the U.S. Bureau of Reclamation facility in the Denver Federal Center, Colorado. The test results verified the design. Crib placement pattern was chosen to maximize support with a confined core crib under the high convergence area. The design has been successfully installed in over 5,000 ft of headgate entry in the 11 left panel.

Jan 1, 1993

By Michael Alber

Pullout tests on resin grouted rock bolts have been executed in coal mines and surface test sites. The goal of this study was to provide some qualitative information about the rock mass quality from mandatory tests with a bit little more effort. Movements of rock bolt head and steel plate at different load levels were analyzed and were found to yield information about the rock mass deformability. The tests were interpreted similar to plate bearing tests and a rock mass compressibility index C was assigned. This index reflects the complex interactions between the rock mass, resin grout and bolt under load. Although further research is necessary it may be concluded that those tests may aid in recognizing geological conditions.

Jan 1, 2003

By Keith Heasley, Christopher Newman, Zach Agioutantis

"Previously, in 2013, a laboratory version of the computer code ARMPS-LAM, introduced at the 32""d International Conference of Ground Control in Mining, successfully integrated the laminated overburden model of LaModel into an ARMPS-style pillar stability analysis. The ARMPS-LAM analysis has now been fully integrated into the ARMPS program allowing users to more accurately classify the stability of a given mine design utilizing a laminated overburden model for the determination of pillar loading within theAMZ. ,This paper introduces the new Windows-based ARMPS-LAM program. The program's ease of use, output result generation, and limitations are highlighted through the parametric analysis of three hypothetical case studies where traditional ARMPS output is compared to output generated by LaModel. As mining operations continue to produce at greater depths and in more complex geometric and geological conditions, flexible and efficient analyses of mine stability for underground room and pillar mining has become more and more essential. The ARMPS-LAM program provides the mining industry with an empirically backed, numerical design tool for the evaluation of underground room and pillar mine plans.INTRODUCTIONIn the Southern Appalachian coal fields of the United States, retreat room-and-pillar methods have allowed mining operations to maintain high rates of production in the face of adverse geologic conditions and shrinking coal reserves. Over the years, research has been dedicated to understanding and mitigating mining-related dangers due to second mining practices, such as: pillar squeezes, floor heave, roof falls, pillar bumps, etc. However, as mining operations continue at deeper depths and with more complex geometric and geologic conditions, there is an inherent industry need for more accurate, flexible, and faster evaluations of stability for underground room-and-pillar mining."

Jan 1, 2016

By William D. Gallant

This paper presents the results of a joint cooperative research project between the CANMET Cape Breton Coal Research Laboratory and the Cape Breton Development Corporation to observe the subsidence profile over the stopline of 2 West panel, Phalen Mine. A novel technique was designed and Implemented to determine vertical displacements of the overlying strata from within a near horizontal borehole drilled over the 2 West panel. Restrictions on data collection techniques due to the submarine nature of the coalfield are discussed. Development and implementation of the borehole technique using a piezometer and inclinometer Is described. Performance of the instruments and profiles obtained by them are presented and compared. Recommendations for design improvements are made to Improve the efficiency of the technique.

Jan 1, 1990

By Joe Zelanko

In order to prevent roof fall accidents and injuries, U.S. underground coal mine operators must develop and implement effective roof control strategies. Various tools are available to assist engineers in developing designs. For example, criteria to address global stability issues (e.g., pillar stability) are well established in the U.S.; effective tools (e.g., empirical and numerical) are available to diagnose potential problems and avoid catastrophic failures. However, most miner injuries occur as a result of local instability (e.g., a roof fall in a single heading or a rib roll from a pillar corner). Hazard recognition and the availability of support plans suitable to those conditions are key to maintaining stability and safety on the working section.

Jan 1, 2011

By Kanchan Mondal, Anthony (Sam) Spearing, Gopi Bylapudi, Joseph C. Hirschi

"The U.S. coal mining industry uses about 100 million rock anchors per year. ASTM F432 specifies the requirements for rock bolts on mines but does not address corrosion. Corrosion has been found to be an issue in Australian coal mines (Hebblewhite et al., 2003 and Villaescusa et al., 2007), where the problem has been researched and stress corrosion has been found to be a significant cause of rock falls. Corrosion is also a major concern for underground civil construction in the U.S. but has not been considered an issue or adequately researched in coal mines. Underground conditions are conducive to corrosion mainly because of water quality and humid conditions. There is a perception, however, that when bolts are fully grouted, adequate corrosion protection is offered to the steel. Research has shown that this is not necessarily the case, due to the formation of micro-cracks as the resin sets and with subsequent rock movement shearing the resin column. This paper outlines a method to determine the corrosion potential of bolts used in long-term excavations and suggests ways to mitigate such effects based on research conducted in the lab and on three mines.INTRODUCTIONResearch on rock anchor corrosion in mines has not been extensive enough in the past, and the effects of several factors in the mine atmosphere and waters are not clearly understood. One probable reason for this lack of research may be attributed to the time required for gathering meaningful data, which makes the study of corrosion quite challenging.Almost all the rock bolts used in coal mines are made from steel, hence the corrosion of iron needs to be understood. The corrosion of iron is an electrochemical phenomenon with the overall equation"

Jan 1, 2010

By Raj R. Kallu

Underground gold mines in Nevada are typically hosted in geologic zones with a wide range of geotechnical properties ranging from blocky competent rock to faulted and highly altered soil-like material. Geotechnical engineering design in weak rock utilizes rock mass classification systems as inputs to both empirical and numerical methods. The most common rock mass classification system utilized in the gold mines of Nevada is the easy-to-use Rock Mass Rating (RMR) system; however, in practice it is difficult to apply in weak to very weak rock masses. This paper attempts to improve the sensitivity of RMR in weak rock masses by utilizing W-RMR?a modified procedure for calculating RMR?and evaluates its performance against other methods of determining RMR for predicting in situ moduli. In-situ rock mass moduli were determined using a portable plate loading device (PPLD), and these data were used to quantify the improved sensitivity of the modified RMR versus existing classification systems. The PPLD was designed for performing rapid and economical in-situ deformability tests in a mining environment. Tests were performed at eight sites yielding thirteen rock mass moduli measurements. Statistical analyses indicate Detailed-Discontinuity RMR-89 and W-RMR provide the best correlations to the in-situ moduli compared to other methods of calculating RMR.

Jan 1, 2014