Search Documents

By Liane J. Terrill

A 9O) ft (275 meter) section of a highly fractured beam of halite was mined from the roof of a supported thirteen year old drift at the Waste Isolation Pilot Plant (WIPP). The operation was conducted with a continuous miner and allowed the unique opportunity to collect spatial information on roof beam geology and to observe ground support conditions during the mining advance. Photographs and fracture maps of the mining face document the progress of the operation and the deteriorated condition of the strata. This case study details the drift's excavation and support sequences. the geomechanical response, and the conditions found in the exposed roof beam.

Jan 1, 1997

By Revendra Awasthi

The application of a horizontal inclinometer and a tiltmeter to measure tilt, curvature, and deformations of shallow footings during mine subsidence is described. The measurements were taken during mining of a longwall panel in Southern Illinois and were supplemented with precision level survey data. Monitoring was conducted under a cooperative agreement between the Institute for Geotechnology at The University of Tennessee, Knoxville, the U.S. Bureau of Mines, the National Science Foundation, the Illinois Mine Subsidence Insurance Fund, and Old Ben Coal Company. Six different footings were constructed and instrumented at two sites; one above the panel centerline, and the second inside the edge of the panel in the anticipated zone of maximum tension. A brief description of the inclinometer casing and tiltplate installation is described, and the results obtained from the two instruments on a plain concrete footing compared. Observations of footing deformations and curvatures calculated from the inclinometer and tiltmeter data are also presented, and the results compared with observed structural damage.

Jan 1, 1990

By Lewis A. Martin

Instrumented cable bolts developed at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health were used in conjunction with existing ground control systems to monitor rock mass loads at Tg Soda Ash's trona mine, Granger, WY. Axial and shear loads were determined to levels of strain gauge accuracy of ±5 N or ±5 microstrain. These gauges were embedded in a remanufactured king wire that replaced the conventional king wire. Cable bolt performance, quality of grout, and installation techniques were also assessed. By using instrumented cables, a mine operator can determine axial load along the cable at predefined gauge locations. These data provide necessary input for an operator to design a safer working environment for miners.

Jan 1, 2001

By Sandin Phillipson

During the course of ground control evaluations conducted by the Mine Safety and Health Administration's Roof Control Division, a number of surface and underground coal mines were visited that exhibited instances of ground failure associated with joints. The evaluations were conducted over a broad geographic area, including the Appalachian Basin from Pennsylvania to Tennessee, and they documented that joints occur in a wide variety of mining conditions and exhibit a wide variety of characteristics. Despite minor local variability in orientations, the joints fit into a cohesive pattern when evaluated on a regional scale in context with the system of thrust faults that define the Alleghany Front. Joints documented for this study, together with joints in sandstone and coal and the trends of drag folds compiled from other studies, were plotted on regional maps using GIS software. The trends of joints, including those that could be described colloquially as "hill seams," were not only parallel to regional fault systems and local trends of drag folds, but were also parallel to the regional patterns of previously mapped joints in sandstone and coal. These observations indicate that the features referred to informally as "hill seams" are in fact joints formed in response to tectonic processes associated with regional deformation of the Cumberland-Allegheny Plateau. The 286-266 million-year-old age of regional deformation significantly pre-dates the time when the Cumberland-Allegheny Plateau was subjected to deeply incised stream valley erosion, which began 25 million years ago. This challenges an existing interpretation that "hill seams" represent local ·stress relief joints that formed when stream valley erosion removed confinement and allowed tensile failure of the rock. Although relaxation of confining stress can reasonably be expected to occur near outcrop, observations indicate that this results in the dilation of existing joints. This paper presents instances of ground failure associated with joints, discusses methods of mitigation, and recommends that the term "hill seam" be abandoned in technical communication because it simply refers to a kind of joint that may exhibit certain weathering and aperture characteristics.

Jan 1, 2010

A computerised influence function approach to subsidence and horizontal displacement prediction is described, with particular emphasis being placed on the applicability of the method to irregular- shaped mine workings. Based on previous work [1], this approach has been put for- ward for inclined seam situations. Examples of graphical output presenting surface subsidence contours, horizontal displacement vectors and principal strain vectors are given and their significance discussed in relation to current problems.

Jan 1, 1988

By N. P. Kripakov

This paper presents a brief overview of current bump mechanics theories and pillar design methodologies, and relates these concepts to experiences at two mines located in a north-central Utah coalfield where different pillar designs were used to control mountain bumps. Experiences gained at the first mine demonstrated the successful implementation of a two-entry, 9.8 m (32 ft)-wide, yield-pillar design. A U.S. Bureau of Mines field study quantified the timing of chain pillar yielding and resulting load transfer from the gateroad. In-mine pillar response, although apparently sensitive to site-specific conditions, compared favorably to estimates derived using two yield-pillar design methods. A second study conducted at another mine located in the same district, but subjected to different geologic conditions, documents the unsuccessful attempts to employ progressively narrower three-entry pillar designs based on successes achieved at the first mine site. This second mine never achieved a true yield-pillar design. Use of pillar widths ranging between 9.1 m (30 ft) and 27.4 m (90 ft) always resulted in violent bumps in the tailgate pillars. The pillars were either too large to yield, or too small to support peak operational loads. Hypothetical gateroad systems were evaluated using both analytical and empirical approaches for configurations comprised of two rows of conventional pillars, and systems incorporating both yield and abutment pillars. Analysis concluded that yield pillars less than 6.1 m (20 ft) wide and abutment pillars ranging between 30.5 m (100 ft) and 39.6 m (130 ft) square would be required to achieve a stable gateroad design. However, results of a field study conducted on a two-entry, 36.6 m (120 ft)-wide abutment pillar concluded that abutment pressures from the first panel overrode the pillar, and that a still larger pillar may be required to preclude bumps in the tailgate during second panel mining. Without the benefit of a demonstrated in-mine success, it is not clear which design would ensure elimination of gateroad bumps.

Jan 1, 1992

By A. H. PH. D Wilson

Compared to the rocks encountered in, say, metalliferous mining or tunnel drivage in igneous and metamorphic rocks, the strata associated with the coal measures are relatively soft. If excavations are made at depths greater than one or two hundred metres, zones of fractured or yielded rock develop around the openings. The stress which can be taken by yielded rock at the boundary of an opening is low, but because of the friction present between the fragments or particles, the sustainable stress rises rapidly with distance from the opening until sufficient confinement has been developed to prevent failure of the rock in the first place. Thereafter the laws of elasticity will apply and increasing distance will reduce the stress field until conditions consistent with the cover load are reached. For rocks which maintain their elastic condition right to the edge of an opening, finite element analysis and similar techniques have proved successful in determining the distribution of stress around the opening. This approach, however, is not successful when a yield zone is introduced between the elastic zone and the opening. Nevertheless, some estimate is required if help is to be given in the siting of roadways and in the determination of adequate pillar sizes. This matter is of particular importance in the planning of new mines especially if retreat faces are involved, as extensive roadway drivage must be planned and executed before experience of the effects of face extraction is gained. In 1977, the author published [I] a method based on 'stress balance'. The total aggregate downward load over a large area will remain that of the cover load even after part of the coal seam has been removed. Any rise in stress in ribsides and pillars must be offset by an equivalent stress reduction across roadways and other areas of extraction, and vice versa. Knowledge of one can lead to an estimate of the other, provided the general form of the stress distribution can be postulated. It is the object of this paper to revue the method in more detail and to give further examples of its successful application.

Jan 1, 1981

By Clare Offner

In 1998, the Australian Coal Association Research Program (ACARP) awarded funding to the School of Mining Engineering at the University of New South Wales to establish a rockbolt testing facility to research anchorage mechanisms associated with fully encapsulated rock bolts and to develop standardised testing procedures for rockbolts. This facility is still under development but has already been used to evaluate the effect of bolt profile and confinement on the load transfer characteristics of a resin encapsulated rock bolt. This paper describes the test facility and presents some of the results of development testing to date.

Jan 1, 2000

By Richard E. Thill

Two Cross-borehole systems were developed by the Bureau of Mines, one operating at a central frequency of 20 kHz for close-in spacing between boreholes (2-20m) and another operating at a dominant frequency between 1-2 kHz for more distant range (40-300+m) between boreholes. The systems are specially designed for the expected ranges and high resolution required in mining applications. Potential applications of the crosshole systems are presented for a variety of geophysical measurements related to underground mining problems.

Jan 1, 1989

This paper is not available for inclusion in the Proceedings at the time of printing, but it will be included as an insert.

Jan 1, 1984

By Takashi Sasaoka, Pinyo Meechumna, Hiroshi Takamoto, Pipat Laowattanabandit, Akihiro Hamanaka, Kikuo Matsui, Hideki Shimada

"The EGAT Mae Moh coal mine is an open-cut coal mine in Thailand that produces about 16 million tons of lignite annually to generate 2,400 mw of electricity. The surface mine pit covers is 4 by 7 km (2 by 4 mi) with mining depths ranging up to 260 m (853 ft). A large pit slope is formed with the progression of the mining operation. However, massive slides in the pit slope often occur due to weak planes, such as faults and bedding, and the weak mechanical properties of the rocks. Hence, a 200-300 m (656-984 ft) boundaries of rock block including coal seams is left in front of faults in order to prevent slides and maintain the stability of the pit slope. As a result, there are significant coal reserves beneath the abandoned area along the pit slope.The focus of this paper is on the applicability and design of the highwall mining for recovering much of the coal left along the pit slope.INTRODUCTIONThe EGAT Mae Moh Mine is located about 630 km (186 mi) north of Bangkok, Thailand (see Figure 1). It is the largest coal mine in Thailand and produces about 16 million tons of lignite annually from open-cut mining (70 % of the total coal produced in Thailand). The coal is used to generate 2,400 mw of electricity at the Mae Moh power plant, which is situated near the mining area. The mine pit covers an area of 4 by 7 km (2 by 4 mi) at varied depths up to 260 m (583 ft) as shown in Figure 2. As the mining operation progresses, the pit becomes to be deeper and deeper. In the year 2035, the bottom of the pit is expected to reach depths of 500-600 m and the open-cut mining operation will be finished. The possibility of an underground mining operation is being investigated.A large pit slope is formed with the progression of open-cut mining. However, massive slides often occur in the pit slope along weak planes including faults and bedding planes due to the weak nature of the rock. As a result, 200 to 300 m (656 to 984 ft) boundaries of rock including coal seams are left in place in front of faults to prevent slides and to maintain the stability of pit slope. Moreover, the dip of the slope is less than that of the planned design. As a result, there significant coal reserves abandoned along the pit slope."

Jan 1, 2010

By Jim Galvin

4 and 6 point timber chock constructions are used extensively on both a systematic and spot basis by Australian longwall operators to support tailgate roadways. In 1996, the School of Mining Engineering at UNSW published design and performance criteria for timber chocks constructed from Australian hardwoods. The research was funded by the Australian Coal Association Research Program (ACARP). In 1997, ACARP awarded funding for a stage 2 testing program. This testing focussed on examining the effect of using thinner timber elements in chock constructions to improve OH&S and comparing the full-scale performance of traditional 4 point chocks to Link-n-Lock constructions. It was established that chocks constructed from thinner elements have failure loads much less than thicker elements. However up to the failure loads of the thinner elements there was no significant difference in the response to convergence of chocks constructed from 25, 50 or 100mm thick elements. Chocks constructed from 150mm thick elements have a similar ultimate strength to the 100mm thick elements. However, they have a significantly lower resistance to load, thereby permitting more convergence to occur. There is more potential for chocks comprised of thin elements to be constructed 'out of plumb' and so suffer eccentric loading. The full scale testing program established that at any given level of convergence up to 10% strain, the timber in a Link-n-Lock chock generates twice the support resistance of the same quantity of the same timber in an equivalent size 4 pointer chock. On the basis of support resistance per cubic metre of timber, there is only a marginal difference in the performance of 1.0m Link-n-Lock chocks and 1.2m Link-n-Lock chocks constructed from select Blue Gum. The cost per tonne of support provided by a Link-n-Lock chock is effectively half of that provided by a 4 pointer chock of equivalent dimension and timber. Up to a strain level of 4%. Link-n-Lock chocks constructed from 1.2m long elements are slightly more cost effective than the same chocks constructed from 1.0m long elements. Thereafter, there is no significant difference in cost per tonne of support resistance. Beyond a strain level of about 4%, Link-n¬Lock chocks constructed from landscape grade Blue Gum are just as cost effective as Link-n-Lock chocks constructed from structural grade 4 Blue Gum.

Jan 1, 2000

By Hamid Maleki

This study presents a historic overview of the role of mobile roof support (MRS) technologies in improving stability and worker safety and presents the results of recent field evaluations of the MRS load rate monitoring device and other remote deformation-monitoring techniques. Field studies were implemented at two sites in cooperation among researchers from the National Institute for Occupational Safety and Health (NIOSH), Maleki Technologies, Inc., and J. H. Fletcher & Co. The objective of the field programs were to (l) study the interaction between MRS's and coal mine strata and (2) develop and test suitable monitoring systems for assessing roof and pillar stability. An MRS consists of a roof canopy, four hydraulic cylinders, a caving shield canopy, and associated electromechanical systems mounted on crawler tracks. The machines are controlled by radio from a remote location and operate on self-contained power units. Typically, MRS's have capacities of 5,340 and 7,120 kN (600 and 800 tons). In comparison to posts, an MRS is capable of maintaining the yield load after significant amounts of roof-floor deformation. Because the mining cycle is accelerated, MRS's help reduce the potential for time-dependent roof falls. MRS performance has been monitored in the laboratory under controlled static loading conditions and in the field under deep, two-scam mining conditions. Laboratory studies have quantified support capacity and system stiffness as a function of machine height. Field investigations have focused on determination of optimum operating conditions and development of warning systems that indicate excessive load on the machine and/or impending roof-pillar stability problems. Analyses of field data show that roof instabilities are influenced by (1) pillar failure, (2) pillar yielding, (3) mine seismicity, (4) geologic structures, and (5) panel layout designs and mining practice. Pillar yielding and failure (unloading) and seismicity can be conveniently monitored by the load rate monitoring device, but for consistent detection of roof falls, additional deformation measurements directly within the cuts ate needed.

Jan 1, 2001

By Josh Johnson, Stephen Tadolini, Mark Ferster, Curt Jacobs

"Stillwater Mining Company is the only U.S. producer of platinum group metals (PGMs) and the largest producer outside of South Africa and Russia. The Company controls a considerable portion of the J-M Reef and is currently developing the ""Blitz Project,"" which will provide a main haulage level, ore pass systems, backfill plants, and flow-through ventilation to increase production and ensure sustainable extraction of this critical strategic mineral. While driving two sub-parallel footwall laterals to about 8,125 m (26,000 ft) long, one of the development drifts experienced a massive fall in a geologically disturbed area created by a dike intrusion. Combinations of a void fill material (Tekseal), polyurethane injection, fore poling coupled with steel arches, and supplemental bolting allow safe and efficient advance through this geologically disturbed zone. This paper presents the details of this project.INTRODUCTIONStillwater Mining Company is the only U.S. producer of platinum group metals (PGMs) and the largest producer outside of South Africa and Russia. The Company controls a considerable portion of the J-M Reef and is currently developing the ""Blitz Project,"" which will provide a main haulage level, ore pass systems, backfill plants, and flow-through ventilation to increase production and ensure sustainable extraction of this critical strategic mineral.Tunnel Boring Machines (TBMs), shown in Figure 1, have been used extensively at both the Stillwater Mine and the East Boulder Mine to develop access to the J-M Reef. The J-M Reef is a PGMbearing reef deposit located in the Stillwater Complex near NyeMontana. The mining property and location are shown in Figure 2.The Blitz Project is named after the Blitz mining claims and is developing the Eastern extent of the J-M Reef Project., This consists of a 5.5 m (18 ft) diameter TBM drive on the SOE (1,562 m (5,000 ft) above sea level and east of the shaft collar) and a 4.7 x 4.7 m (15 x 15 ft) drill and blast heading on the 5,600E (1,750 m (5,600 ft) above sea level and east of the shaft collar). The Benbow Decline will be completed running perpendicular to the TBM by drilling and blasting methods. The TBM drift will be used for exploration drilling, ventilation, and will serve as the main haulage level. The 56E will be used for ventilation and exploration drilling. The Benbow decline will serve as the exhaust drift."

Jan 1, 2016

By S. Jayanthu

This paper presents analysis of strata behaviour with special reference to convergence and stress variation during an experimental trial of extraction of pillars with cable bolts as major support system in 6.5 - 8.0 m thick coal seam. Critical span for roof falls was estimated through empirical models and also evaluated by numerical models. In situ strata behaviour studies during 1992-96 for about 70 local/major falls revealed inadequacy of the available literature for interpretation and prediction of the roof falls. Convergence acceleration and variation of induced stress based on continuous monitoring data showed distinct anomalies and potential for better understanding of strata mechanics during pillar extraction.

Jan 1, 1998

By Keith Heasley

As part of the initial investigation and validation of a new boundary-clement formulation for stress modeling in coal mines. the underground stresses and displacements at two multiple-seam coal mines with unique stress problems are modeled and predicted. The new program, LAMODEL, calculates stresses and displacements at the seam level and at requested locations in the overburden or at the surface. Both linear elastic and non-linear seam materials can he used: and surface effects, multiple seams, and multiple mining steps can be simulated. In order to most efficiently use LAMODEL for accurate stress prediction, the program is first calibrated to the site-specific geo-mechanics based on previously observed stress conditions at the mine. For this calibration process. a previously mined area is "stress mapped" by quantifying the observed pillar and strata behavior using a numerical rating system. Then, the site-specific mechanical properties in the model are adjusted to provide the best correlation between the predicted stresses and the observed underground stress rating. Once calibrated, the model is then used to predict future stress problems abead of mining. At the two case study mines, the calibrated models showed good correlation with the observed stresses, and also accurately predicted upcoming high stress areas for preventive action by the mines.

Jan 1, 1998

By Thomas M. Baraak

This paper evaluates factors which influence longwall support and strata interaction. The longwall system is composed of an immediate and main roof structure and three supporting foundations: 1) longwall panel, 2) powered roof supports, and 3) gob waste. The main roof forms a structure that is generally supported by all three foundations, while the immediate roof acts as a beam that cantilevers from the coal face to the powered support. In most cases, shield loading involves a complex interaction of both main roof and immediate roof behavior and is a combination of loads produced from subsidence of the main roof and displacements of the immediate roof caused by deformations of the cantilevered roof beam. Since the shield stiffness remains constant for all leg pressures and main roof convergence is irresistible in terms of shield capacity, the shield must be able to control the behavior of the immediate roof or floor structure for shield loading to be sensitive to setting pressures. If the goal is to minimize total shield loading, any active setting force must be offset by reduced passive shield loading to justify the active setting loads. Field data suggest that the typical reductions in passive loading do not justify the required increases in setting pressure in some applications.

Jan 1, 1990

By Gerald I. Finfinger

Identifying the properties of overlying rocks in underground mining operations is important to ensure the appropriate roof support design is used to maintain stability of the mine entries. Recently J. H. Fletcher & Co. developed a monitoring and control system for roof bolters for the underground mining industry. The system records the drilling parameters used during roof bolt drilling and the information can provide insight into the physical properties of the roof strata. The parameters include thrust, rotational speed, torque and velocity and the measurements are collected every 0.1 second during the operation. The drilling parameters were analyzed to determine the application of identifying the strength of rocks being drilled from the measurements. The data was converted into the specific energy of drilling which is a measure of the amount of energy required for removing a given unit of rock during a drilling operation. The laboratory studies completed to date indicate a fairly high correlation between the specific energy of drilling and the unconfined compressive strength of the rocks that were drilled. Additionally, the drilling parameters were shown to be effective for identifying the presence of fractures or bed separations between rock ]avers. The thrust, torque and specific energy of drilling were all good indicators for identifying the fractures or separations. Regardless of the drilling parameters used during the drilling experiments, the location of the fractures were identified, In order to determine the application of the drilling parameters for identifying rout rock properties, two series of experiments were conducted. The first series of experiments used three "manufactured" roof layers that had various rock samples embedded in concrete blocks. The rock samples included three types of sandstone, marble. and argillite. Another concrete block was poured with foam inserts to simulate large bedding separations (2 to 8-in). Two other manufactured blocks were constructed using high-strength concrete with cardboard layers embedded to simulate smaller fractures or bedding separations. The size of the cardboard layers varied from 1/8- to 1-in thick. One of the blocks had the cardboard layers embedded at an inclined angle to determine the effect of the orientation or, the drilling parameters. A series of experiments was conducted with the rotational speed and the penetration rate held constant and the thrust and torque allowed to vary. The information collected from the experiments is used to determine the application of the drilling parameter measurements for identifying rock properties, fractures and bedding separations.

Jan 1, 2000

By David Bigby

A remote reading dual height telltale system has been developed to provide mine management with early warning of impending roof failure. This system is a logical development from the visual dual height and triple height telltales which are increasingly being used worldwide for routine monitoring of mine roof. The paper describes the principles and history of telltales from their origins in France, their refinement and routine use in the UK and their subsequent spread around the world. They are now being used in various forms in USA, Canada, Germany, Spitzbergen (Norway), Poland, Ukraine, Russia, Australia, South Africa, Mexico, India, Egypt and China. The remote reading telltale system has coal mine intrinsic safety approval in Europe and the United States (MSHA) and the first commercial system was installed in a German colliery at the beginning of the year. Up to 100 dual height telltales can be connected, in a simple "daisy chain" configuration, to each of 4 underground interrogation units. These are connected through a twisted pair link to a surface computer which displays the readings, updates the database, generates warnings and provides the user interface. The paper describes the features and principles of operation of the system which differs considerably from conventional mine-wide monitoring systems. A European Community funded research programme is currently underway with the aim of developing improved alarm generating algorithms including evaluation of interfacing a neural network to the system. The paper concludes by exploring other potential applications of the system for ground control monitoring currently in development, including extensometry, stope closure monitoring and support load measurement.

Jan 1, 2001

By Anil Mahyera

Under contract to the Bureau of Mines, a roofbolting machine has been developed which will: control torque on the bolthead to within 4 percent of a set point, control thrust to a low level (150 lbf), and implement a tightening method to minimize variability due to bolt tension decay of a group of bolts caused by differing anchor creep rates. This bolter was used to determine bolthead and thread friction factors, and to determine the effect of adding a hardened washer to the bolt assembly on the uniformity of bolt tension in the laboratory and field. Recommendations for torquing speed, bolt lubrication, use of hardened washers, and thrust level on the bolthead are made. The relationship of this system to Improved roof control is discussed, along with additional work that remains to be performed. Patent Notice Patents are pending which protect the hardware and methods of controlling tension decay as discussed in this paper.

Jan 1, 1981