Search Documents

By W. Petruk

Mineral liberations that would be obtained by grinding an ore to a specific size can be predicted by analyzing unbroken ore pieces, and mineral liberations in ground ores and mill products can be determined directly by image analysis. Predictions of mineral liberations are made by measuring size distributions and textures of mineral grains by image analysis and using liberation models. Ground ores and mill products are analyzed to determine the proportion of mineral that is liberated, and the data are used to evaluate mineral behavior during mineral beneficiation. The liberation data for minerals in a suite of mill products from a circuit are processed by a materials balancing technique to calculate recoveries of minerals in different types of particles throughout the circuit. The liberation-materials balance data define mineral recoveries; define the behavior of an ore in a concentrator, pilot plant or bench test: and indicate whether recovery improvements are possible and/or feasible.

Jan 1, 1992

By P. Legast

Serpentinite minerals are available in large quantities from asbestos mining activity. The granular or fibrous serpentite, at temperatures greater than 700°C, will recrystalize into olivine, forsterite and enstatite. These minerals have been used and studied for decades and are environmentally safe. The thermal process changes the composition and properties of the original mineral. Therefore, the substitution of the original mineral cannot simply be made and the applications for these new synthetic minerals need to be redeveloped. The two original mineral forms allow a wide range of new synthetic raw materials which can be adjusted to specific applications or custom needs.

Jan 1, 1993

By William J. Shampine

This map shows general trends of the chloride concentration of water in the upper part of the Floridan aquifer. Below this part of the aquifer, high chloride water can be found everywhere in the State. The accompanying cross section shows the depth to salty water across central Florida. In the center of Florida, fresh water may be found as deep as 2.000 feet, whereas, along the coast it may extend no deeper than about 200 feet. Chloride concentration in small local areas may deviate from the values represented on both the cross section and the main map. This map shows general trends of the chloride concentration of water in the upper part of the Floridan aquifer. Below this part of the aquifer, high chloride water can be found everywhere in the State. The accompanying cross section shows the depth to salty water across central Florida. In the center of Florida, fresh water may be found as deep as 2.000 feet, whereas, along the coast it may extend no deeper than about 200 feet. Chloride concentration in small local areas may deviate from the values represented on both the cross section and the main map.

Jan 1, 1966

By Yi Luo, Jian Yang, YUJIA LIAN

Scale physical models, constructed according to the principle of similarity theory, have been widely used to simulate the mining disturbances to surrounding strata and to evaluate the effectiveness of implemented ground control techniques. This technique has also been used for studying mining-induced surface and subsurface subsidence. The movements of the observation points installed on the physical model at different mining stages are currently measured using total station which is time-consuming and inaccurate especially on small scale models. A photogrammetry-based measurement system has been developed. During a physical modeling process, photos of the model can be taken during the simulation process reducing survey time from hours to a few seconds. A program, Photogrammetry Analysis for Physical Modeling of Mine Subsidence Process (PAPMMSP), developed based on photogrammetric principle is used to quickly identify the installed observation points and accurately determine their coordinates. The measurement accuracy is well under submillimeter level—an ultra-important advantage as any measurement errors in coordinates are magnified by the model dimension scale (commonly 20 to 400). A physical modeling case of subsurface strata movements and deformations associated with longwall mining operations is presented in the paper to demonstrate the functions and capabilities of the developed photogrammetry program.

Aug 11, 2020

By Rene Padilla, Siyanda B. Mngadi, Gerrie van Aswegen, Peter Stonestreet

While many mine tunnels are developed through ground that must be riddled with the sources of small (and larger) mining induced seismic events, recorded by the mine seismic monitoring systems, we do not see planar discontinuities classified as seismic sources in the geotechnical databases. Here we list criteria that may be useful to identify discontinuities in drill core which are dynamic slip surfaces, parts of mining induced seismic sources. Such shear rupture surfaces in core would generally be powdery, cohesionless, and rough on cm scale. Finely broken rock and rock flour may be found in the core boxes at the discontinuities. Slickensides would be soft (easily destroyed) and kinematically consistent with the local stress field. In some cases, a cross fabric would be present, orthogonal to the slickensides, being the intersections of en-echelon extension fractures, within the dynamic shear zones, with the shear zone walls.

Apr 26, 2022

By A. N. Islam, C. Simons, M. N. Hughes, J. Barrett

The effluent from the bio-oxidation of arsenopyrite contains high concentrations of iron(III) and arsenic(V), the pH being in the range 1.0-1.3. The use of lime to increase the pH causes the precipitation of calcium sulfate, calcium arsenate and a mixture of solids containing calcium, iron and arsenic. The presence of calcium is due to slaked lime encapsulated by the iron arsenate precipitates. These iron arsenate solids are related to known minerals. The use of sodium hydroxide to effect the precipitation of iron and arsenic produces solids which are more stable than those produce by using slaked lime. The use of limewater produces an initial precipitate of calcium arsenate.

Jan 1, 1991

By M. A. Bronston

A drill system configuration capable of working in the arctic offshore environment was developed to evaluate the placer gold resources contained in the glacio-fluvial sediments offshore Nome, Alaska. This system is capable of working on the shore fast ice during the winter months and is deployed on a drill ship during the summer. Transfer of the drill between its summer and winter configurations is accomplished with a minimum of modification to the design. The system is designed around the Becker drill. This percussive, reverse circulation drill is capable of penetrating the indurated glacial sediments present in the offshore Nome environment. This drill has operated effectively to depths in excess of 50 m (164 ft) below sea level. Since early 1987, in excess of 2000 holes have been drilled using the system. The drill system often operates in extreme weather conditions. It has averaged approximately 10 holes a day of drill production. The ore reserves defined during these drilling programs have resulted in the recovery of more than 70,000 oz (2.18 t) of gold to date, by the mining vessel Bima.

Jan 1, 1990

By D. M. Hausen

The role of applied mineralogy in mineral beneficiation begins with early prospect evaluation, and continues through stages of amenability testwork and pilot plant studies to the ultimate development of viable processes for mineable orebodies. After plant construction, mineral products from various locations, i.e., grinding circuits, flotation cells, gravity circuits, kilns, smelters, etc., require quick identification and control monitoring for optimum efficiency and recovery. Ore/gangue minerals are identified, quantified, and textural associations investigated by microscopic, spectrographic, and electron-optical instruments. Mineralogic analyses of large numbers of samples have required the development of sophisticated computer systems that merge analytical and mineralogic data into useful diagnostic data bases

Jan 1, 1991

By Hetland Donald L.

Regional Tertiary formations and basins of local sedimentation which contain uranium deposits west of the Rocky Mountains are mainly of Oligocene, Miocene, and Pliocene age (fig. 1). The host rocks have been derived mainly from intrusive and extrusive igneous rock. The major host formations which cover broad geographic areas include the Esmeralda, Truckee, Humboldt, Thousand Creeks, Payette, Panaca, Cedarville, Coso, and San Joaquin Formations. Local areas of Tertiary sedimentation containing uranium deposits occur near Yuma, Safford and Artillery Peak, Arizona; Dillon and Canyon Ferry, Montana; Spokane Indian Reservation and Pend Orielle River, Washington; Topaz Mountain, Utah; Stanley Basin, Idaho; and Sonora Pass, California. Uranium deposits in these sediments have been classified into five categories based on environment (fig. 2). They are: (1) Deposits in lake sediments consisting mainly of water-laid tuffs; (2) Deposits in lake sediments intruded by volcanic plugs; (3) Deposits in lake sediments interbedded with arkoses near batholiths; (4) Deposits in coarse volcanic sediments in local sedimentary basins; (5) Deposits in arkosic conglomerates in local sedimentary basins.

Jan 1, 1969

By K. V. Raj, C. A. Berry, A. T. Weakley, A. L. Miller, P. R. Griffiths, D. A. Parks

Diesel particulate matter (DPM) has been classified as a carcinogen to humans by the International Agency for Research on Cancer. As a result of its potential carcinogenic nature, DPM exposure is regulated by the Mine Safety and Health Administration. Currently, diesel emissions in the workplace are monitored by collecting the aerosol onto filters, which are then sent to a laboratory for thermal-optical analysis using the NIOSH method 5040. This process can take days or even weeks, and workers can potentially be exposed to excessive levels of DPM before the problem is identified. Moreover, the delay involved in getting the loaded filter to the lab inevitably means the loss of some of the more volatile organic carbon. To remedy this delay, researchers from the National Institute for Occupational Safety and Health are seeking to develop a field-portable, real-time method for measuring elemental and organic carbons in DPM aerosols. In the current study, the use of mid-infrared spectrometry was investigated. It is believed that mid-infrared spectroscopy is more suitable for use in a real-time field-portable device than thermo-optical analysis methods. This article presents a method for measuring organic carbon (OC) and elemental carbon (EC) in DPM for a broad range of OC/EC ratios. The method has been successfully applied to laboratory-generated and mine samples.

By Ronald J. Thomas

Prior to 1974, bauxite-producing countries were poorly informed about important aspects of the bauxite/alumina/aluminium industry. This placed them at a disadvantage in negotiations over the development of the industry with interested parties. Since the formation of IBA, its member governments have acquired a fuller awareness of the structure and operation of the industry. The role of IBA is to enlarge the relevant information base of member governments, to act as a forum for the exchange of information on the industry and to form a focal point for multilateral discussions on problems in the industry with corporate interests and with governments of consuming countries.

Jan 1, 1984

By S. C. Tadolini, P. Mills

"INTRODUCTION This research produced a shotcrete formulation that extends beyond stabilization and can be used to restore the structural integrity of damaged infrastructure. The primary challenge was to develop a shotcrete or gunite with structural strength within a few minutes to prevent parasitic loading and allow ingress into damaged structures within a few minutes of the mix formulation being applied. This also applies to mining conditions where rapid support of progressive failures can minimize failure. An additional benefit was the discovery that the product had extremely high adhesion properties in addition to high flexural strengths. The approach to product design was the development of “single bag” dry mixes that are entirely self-contained, can be rapidly transported anywhere in the field or underground, and be deployed using simple equipment. Dry mix eliminates issues relevant to high shear water mixing, as water is added in the form of a mist at the point of delivery; thus low W/C can be achieved. However, as there is no onsite powder mixing, the product must have a high degree of inherent homogeneity. A commercial version of this material is currently offered as Minova’s Tekcrete Fast® product which has been successfully deployed in the mining industry and is currently being used in civil, construction and tunneling operations. The material can rapidly stabilize unstable ground in metal/nonmetal and coal mines. This paper described the technology development, product testing results and applications in mining and civil applications. BACKGROUND The original development of this product was to complete rapid stabilization of shock damaged structures, which falls outside the purview of normal construction and mining practices, due to the critical time issue and the nature of the damaged structure. The stabilization of damaged structures requires materials and equipment that can be rapidly deployed to place materials that have very rapid strength development. These materials need to be placeable at a distance to provide some degree of safety to the responders. In addition, the materials must be able to adhere to structural surfaces that have not been specially prepared and conditioned, and may also be highly fractured, dusty, wet, and quite possibly hot or extremely cold. The technology for the rapid delivery of large volumes of cementitious materials to vertical or even overhead surfaces currently exists. Pneumatic delivery (shotcreting) has been used in construction for over 100 years (American Shotcrete Association, 2014). Shotcreting has played a major role in structures like the Washington D.C. Metro subway system and been used in underground mining applications routinely to serve as part of the primary and secondary support system when used in conjunction with traditional roof bolts. Numerous rapid setting cements are commercially available. They are used for rapid repair of surfaces such as bridge decks, pavements, and commercial floors, as well as structural repairs of vertical and overhead surfaces. Few of these products are specifically marketed for use in shotcrete applications. The majority of rapid setting cements are based on, or at least contain, Portland cement as a principle component. Other components are added that help provide early strength, such as high alumina cement (HAC), organic polymers, chemical accelerators (which can also be added during concrete batching), and calcium sulfate hemihydrate (e.g. gypsum plaster) (Lea, 1971). Cementitious mortars prepared with some of these cements can achieve compressive strengths of 6.8 – 13.8 MPa (1,000-2,000 psi) within 1 hour. However, Portland cement mortar and concrete typically require many weeks of proper curing to reach significant levels of their ultimate strengths, even when used with set accelerators. Also, high early strengths require the use of large proportions of Portland cement in the concrete mix, which can lead to high heat evolutio"

Jan 1, 2017

By S. Jennings

The Red Dog massive sulfide deposit is located in the western Brooks Range of Alaska 100 miles north of the village of Kotzebue. It contains the largest zinc reserve in the world. Reserves were doubled in 1995 with the discovery of the Aqqaluk deposit and significantly increased in 1996, with the discovery of a deep zone of mineralization to the north. At present the global reserve and resource is 143 million tonnes of 16.1 % zinc and 4.3% lead. Red Dog is a silica + sulfide synsedimentary replacement deposit hosted in barite and black shale of the Mississippian Kuna Formation. Red Dog was thrust northward during the late Mesozoic Brookian orogeny. Understanding the setting of the deposit at the time of formation and its subsequent deformation history is critical to current exploration efforts and to future discoveries in the district.

Jan 1, 1998

By S. L. de Moraes

This study aimed to identify a way to reduce the use of bentonite in the pelletization of magnetite. With this goal, different combinations of binders were compared to bentonite by examining the quality of pellets obtained by balling drum agglomeration. Pellets were subjected to routine tests that included simple compression of the wet and dry 105°C pellets, dropping wet pellets to determine their ability to survive handling and submitting pellets to thermal shock to determine how they tolerate drying and preheating. The best results use sodium silicate (1.5%) as a binder and show that it is possible to pelletize iron ore without using bentonite.

Jan 1, 2010

By Newell H. Orr

Titanium's performance characteristics in acidic oxidizing and mildly reducing environments make it applicable to numerous currently defined and many projected hydrometallurgical applications. With titanium's current and projected availability and price stability increased use in pressure leach, piping systems and electrorefining is practical.

Jan 1, 1983

By Joseph E. Worthington

Increases in the price of gold starting about five years ago, and rapid fluctuations since then, have caused a substantial popular interest in the noble metal. Gold prospecting had been at low ebb since the end of World War II in most of the United states except for a flurry of activity in Nevada occasioned by the Carlin and Cortez discoveries. The last five years, however, have seen a great awakening of interest in gold exploration as well as an opportunity for education for many explorationists in the geology and other vagueries of gold deposits. The present writers have participated over the last few years in a search for gold deposits throughout the United States. This search was greatly influenced by the geologic studies of Dr. Wm. Spence at the Haile Gold Mine in South Carolina as reported in a companion paper. Spence's studies resulted in definition of a geologic model that has proven useful in a number of other geologic environments in the united states. These programs were all carried out under the auspices of Cyprus Mines Corporation and permission by Cyprus to present these results is gratefully acknowledged. The writers, however, reserve for themselves all responsibility for the results and conclusions. The exploration program to be described began in the southeastern United States. Spence's studies provided a reasonable basis for interpreting and understanding the geology of the Haile deposit and also provided a means for predicting additional occurrences. This concept was then expanded to other gold occurrences in the Piedmont and became an effective tool for evaluating other prospects. Finally it became evident that the concept could be applied in some western gold districts. The following discussion will then include descriptions of other Piedmont examples and a few western districts that also appear to fit the pattern.

Jan 1, 1978

By Mark H. Johns

Leaching of waste material at Kennecott's Chino Mines Division at Santa Rita, New Mexico, has been accompanied by increasing difficulty in circulating leach solutions through the dumps. As a means of recognizing existing problems and considering alternative applications of the leaching concept, a leaching research program was proposed which could be applied to a specific, typical waste dump. Conclusions derived from the area could then be applied to other leaching areas at Chino. Associated with the program was an evaluation of the physical characteristics of the area using Chino's drilling and radiation logging techniques.

Jan 1, 1970

By Donald W. Foss

The Shiloh Church deposit is a very significant molybdenum occurrence in an ususual, perhaps unique, geologic environment. Work done to date indicate that several million tons of "ore" may be present, occurring as a matrix in limestone and dolomite breccias. Mineralized rocks cored to date are at or near the surface and the deeper resource potential has not been tested. The prospect is located in Polk County, north- western Georgia (Fig. 1). The "ore zone" was outlined by North American Exploration, Inc. (NAE) using geochemical prospecting techniques. Extensive geological work, including core drilling, has been conducted on the properties, together with geochemical and geophysical surveys. The geology, geochemistry and geophysics of the prospect are discussed. It is hoped that these data can be used to formulate exploration programs in similar terranes located elsewhere in the eastern U.S.A.

Jan 1, 1983

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

Jan 1, 1986

By B. A. Rose

Coal is being thermally dried in ever increasing tonnages today. Because of fire and explosion hazards, it is important that drying equipment be designed for maximum safety in operation. It is well then that we review dryer design and operation to bring out those features and operating practices which will provide maximum safety to equipment and personnel. This paper presents the author's views regarding the fundamental requirements for safety and explains the Heyl and Patterson approach to the meeting of those requirements in the design and operation of their dryer.

Jan 1, 1962