Search Documents

By M. Noaparast, F. Woodcock, A. R. Laplante

A novel methodology for estimating gold recoveries in gravity-separation circuits is presented. The methodology makes use of a population-balance model. The model represents gold liberation, breakage and classification behavior and applies preconcentration and recovery performance curves to gravity-recoverable gold. The derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and from a projected application. The methodology makes it possible to estimate the performance of a gravity circuit having a large gold circulating load and a relatively-low unit recovery (e.g., a jig) or having a high recovery on a bleed of the circulating load (e.g., a Knelson Concentrator).

Jan 1, 1996

By Peter Zhang, Daniel Su, Mark Van Dyke, Heather Dougherty

The integrity of shale gas wells in longwall chain pillars under the influence of longwall mining is a safety concern for both coal and gas operators. Previous modeling studies of gas wells in longwall pillars have shown that a FLAC3D model can predict longwall-induced stresses and deformations in gas well casings with reasonable accuracy. The predicted casing deformations can be verified by multi-finger caliper survey. This study concerns the influence of longwall mining on eight shale gas wells in a shale gas well pad located in the chain pillars between two adjacent longwall panels under 1,030 feet of cover. FLAC3D modeling was performed to predict longwall-induced deformations in gas well casings based on site-specific mining and geological conditions. Small deformations less than 0.5 in were predicted in the intermediate casing above 600 ft depth, and very small casing deformations less than 0.15 in were predicted below 600 ft due to high abutment pressure and high frictional resistance along the weak bedding interfaces. After the first panel was mined, a 56-arm caliper survey was performed on one of the wells to measure the longwall-induced casing deformations in the intermediate casing. The predicted casing deformations were then compared with the measured deformations, which indicated that the prediction was generally in good agreement with the measurement in terms of deformation locations and magnitudes. Findings from this study provide valuable information not only for stability assessment of shale gas wells in longwall chain pillars but also for developing engineering guidelines to preserve casing integrity through adequate pillar and casing design.

By Arshad Ali, Mudassar Khan, Waqas Ahmad, Nisar Muhammad, Muhammad Salman

Talc is an important industrial commodity due to its wide-ranging intrinsic properties; however, the presence of iron oxide hinders its industrial utilization. Herein, we report the purification of Pakistani talc through acid leaching assisted by chlorination techniques. Among various acids (i.e., HF, HCl, H2SO4, HNO3, H3PO4, Aqua Regia, H3BO3, and CH3COOH), HF was the most effectual, removing up to 67% of iron oxide at optimized conditions of temperature, 90–95 °C; time, 120 min; HF concentration of 5%; and at a pH of 1. In the second step, chlorination of the talc sample was performed separately by both wet chlorination and dry chlorination. Wet chlorination was carried out using KMnO4 and HCl in slurry phase which shown about 52% removal of iron oxide, whereas dry chlorination with CaCl2 at high temperature attained about 48% removal of iron oxide from talc sample. Further, the wet chlorination of HF leached samples was also performed under optimized conditions which showed up to 87% iron oxide removal. The original and treated talc samples were characterized by EDX and XRD analysis to monitor the changes in the elemental and mineralogical composition of the talc. It can be concluded that HF leaching followed by wet chlorination is an effective method for the upgradation of low-grade Pakistani talc ores.

Aug 9, 2021

By H. M. Lima, P. Wathern

There are many different words to describe mine closure, including rehabilitation, reclamation, restoration and decommissioning. Closing mining operations, mainly open pit mines, has required resolution of numerous issues. Mine closure plans involve environmental-protection issues, regulatory issues and community issues. The obvious, and often most expensive of them, is the physical rehabilitation of the disturbances and the elimination of long-term commitments and maintenance. This paper outlines mine closure planning and its important component, mine-site rehabilitation. Community consultation and involvement are also referred to as an important component of the mine-closure plans, which are required to ensure satisfactory mine site rehabilitation. Considerations of socioeconomic impact of mine closure and long-term responsibilities are presented.

Jan 1, 2000

By Stanislaw Nawrat, Waclaw Dziurzynski

An increasing concentration of coal production, especially in the circumstances of intensive methane inflow makes the coal mine managing staff apply new techniques of safe mining. It paves also the way for scientists to develop new directions of investigations and implementation of state-of -the- art technical solutions. Simultaneously, it could be noticed that the funds assigned for expansive 'En situ ' investigation are continuously decreasing. Better and better results are reached when applying computer technique in calculations of the parameters of ventilation process. Recent theoretical and experimental investigations of air and gas (methane) flow in longwall areas with caving, combined with the implementation of methane drainage system allowed to create, a mathematical model and consequently to elaborate a computer supported numerical simulation of discussed phenomena. The mathematical model has been modified and the simulation program was prepared in such a way that the software is convenient for a user looking for an optimal solution. The paper presented the methodology of optimal choice of following parameters: - ventilation system - rate of flow through the wall. The procedure takes into consideration keeping a safe level of concentration methane in air flowing through the longwall as well as the criterion of maximum methane concentration within the methane drainage pipe line. Results of variant computer simulation regarding the longwall with caving are shown in graphs and tables.

Jan 1, 1995

By R. G. Graber

Field testing of GPS mining applications has confirmed the technical and operational viability of GPS for precise, centimeter-level positioning in harsh taconite environments. GPS hardware has provided consistent availability exceeding 90%, with precision in certain applications of ± 0.07 foot at 95% confidence levels. Despite these technical successes though, challenges persist in achieving effective GPS integration. These challenges include the acceptance of new job tasks by mine personnel, the capacity of typical mine data communications infrastructure and the need to design GPS interfaces for new mining equipment.

Jan 1, 1998

By J. T. Gepford, K. A. Prisbrey, T. Scott, M. Spangler

Using neural networks for plant control is challenging. The objective was to show how to make a neural network effective, even with noise, lag times, and unmeasured disturbances in the plant. The procedure was to evaluate the neural network in a laboratory flotation vision system and in a plant refractory gold autoclave system. Although the resulting neural network easily conquered simple laboratory data, the noisy plant data was much more difficult, and adaptive linear models were equally effective. We concluded that the neural network needs support by combining it with other tools found in the best control packages.

Jan 1, 2000

By J. S. Stachulak

Installation of a computerized mine monitoring and control system in two planned construction phases began in 1983. Phase one consisted of providing a central monitoring station located on surface for monitoring underground CO detection in Frood Mine's heated area. The implementation of this project annualized labour savings of $200,000. The cost of installation of an early fire warning system was $100,000. There are several CO sensor monitoring carbon monoxide trends through mine heated areas. To obtain an early warning, it is not good enough to know that a fire has started, but it is also necessary to know where the fire is located.

Jan 1, 1989

By Herbert S. Richey

Two hundred years ago next April, our forebears embarked upon the difficult path to national independence. They succeeded, and shook off the yoke of foreign domination. In the ensuing two centuries, the country was mobilized several times to protect that political and economic independence from foreign domination. These efforts were also successful. Thus, as we stand here on the threshold of our third century of political independence, we can thank previous generations and congratulate ourselves for establishing and maintaining the world's oldest republic. Now -- once again -- the United States faces the challenge of foreign intervention into our economy. This time the battleground is resource avail- ability. America has been blessed with enormous resources. Whether we speak of minerals or timber or water or "amber waves of grain," this nation has benefitted from a resource base that is the envy of the world. This asset, coupled with a political system that permitted us to develop it, has been the physical backbone of our independence. Without the economic independence that this resource base has given us, the political independence we fought for would have been tenuous, at best.

Jan 1, 1975

By R. R. Rollins

Field data combined with theoretical derivations were used to design a surface mining operation using explosive casting. Calculated casting results varied from 44 to 65% depending on bench height. This model was then applied to field tests at an eastern, contour, coal stripping operation. Results from five experimental casting shots are summarized and compared to conventional mining methods. The overburden material removed by casting ranged from 35 to 65% with an average of 50%. Fragmentation was improved and it was demonstrated that this procedure is economically attractive with a resultant cost savings of $.59/m3 or $5.93/t of clean coal.

Jan 1, 1987

By Koichi Nishimura

Japan's coal reserves are estimated at 8,583 million tons (according to the materials on X World Energy Conference,. 1976). Japan is a long island country in the shape of an elongated cashew nut whose top is pointing to the north and its lower tip is pointing to the west. And her major coal fields are located in the two extreme far parts of Hokkaido in the north and Kyushu in the south. On the other hand, Japan's major industrial center are located in the central part of the country far from either coal-producing areas. This fact places coal a great geographical disadvantage in comparison with petroleum whose refining bases are concentrated on the coastal regions virtually next to major industrial centers.

Jan 1, 1982

By H. Zhu, A. G. Journel

Qualitative and interpretive information as obtained from geological and/or geophysical studies, in addition to precise measurement, is incorporated into the estimation process through an indicator variable. The indicator conditioned estimator is formulated as a cokriging, and its expression is data value dependent as opposed to that of the traditional kriging estimators. The solution of the dual cokriging system provides simultaneously an estimate of the unknown and an estimate of the conditional probability that the unknown belongs to a specific population or class. Being an unbiased and minimum-error-variance estimator by construction, the indicator conditioned estimator is better in the least square sense than the ordinary kriging estimator because it uses additional information carried by the indicator data. A case study using a large reference database is presented; the indicator conditioned estimates have a smaller conditional bias and a smaller error variance than the ordinary kriging estimates. The results also showed that the indicator conditioned estimator is more efficient for selection in mining.

Jan 1, 1990

By D. W. Park

Longwall mining is considered the most efficient underground coal mining technique in terms of coal extraction ratio, production rate, and safety standards. Due to the increasing demand for higher coal production, wider panel and faster face movement have become the recent trends. Thus, longwall mining can create unexpected threats such as roof falls, excessive face convergence, shield damage and numerous maintenance problems causing sudden interruption of coal production and serious safety hazards. A recent study at the University of Alabama is dedicated to develop LoSCoMS (Longwall Strata Control and Maintenance System) which integrates real-time shield monitoring, data presentation, analysis, forecasting, and warning modules. The main objectives of this system is to provide the stability and maintenance information, at every minute, such as high load, low setting pressure, leg leakage, etc., analysis of various mining and geological parameters to determine past and present roof characteristics and forecasting of loading patterns for the following mining cycles, next periodic weighting, etc. Using this unique system, mine operating personnel are well aware of past, present and future roof loading patterns at the longwall face, and thus, proper safety measures can be taken ahead of time.

Jan 1, 1997

By Terence G. McCusker, E. Roy Anderson

A four-mile length of interceptor sewer tunnel in Manhattan has finished sizes ranging from 10'6" to 14'6" horseshoe. Mixed face conditions were anticipated in three areas and encountered in five. All were short but since the tunnel lies well below the water table and failures would involve important utilities, major structures and human lives, great care had to be exercized in choosing a construc¬tion method. Chemical consolidation was selected as the best approach with compressed air working as a backup system. Initially grouting was accomplished from within the tunnel, but treatment from the surface was more successful and was later adopted. The soils consisted largely of impermeable weak silts and it was found possible to inhibit access of water to this material so that it could be controlled by breasting within the tunnel without loss of stability. It is concluded that in the interlayered permeable and impermeable soils encountered, chemical grouting would successfully stabilize the working face. INTRODUCTION An interceptor sewer is currently under construction along the entire length of the west side of Manhattan. When complete, the tunnel will intercept and divert to a treatment plant (also under construction) a daily flow in excess of 200 million gallons per day. About 9 miles of the interceptor sewer is in tunnel and the remain¬der is cut-and-cover construction. The tunnel is almost entirely in Manhattan schist but where its alignment crosses major faults at comparatively shallow depths, mixed face and earth conditions are

Jan 1, 1997

By R. Harris, M. Misra

Column flotation technology has a demonstrated potential for recovering clean coal from high-ash waste fines. The effect of different variables such as air flow rate, frother addition, depressant addition, percent solids and particle size on the quality of separation are discussed. Results indicate that air flow rate and depressant addition are the important variables which control the selectivity in the flotation of fine coal in a column cell. Separation efficiency achieved with column cells is significantly better than that with conventional flotation cells. Under appropriate experimental conditions with a deep column, more than 80 percent coal can be recovered in the concentrate containing 10 percent ash from waste fines containing over 60 percent ash.

Jan 1, 1988

By John E. Wallace

A recent study by the New York Trap Rock Corporation has conclusively determined that the number of blasting complaints is directly related to the noise produced by the blast. In turn it has been known for some years that the noise produced by the blast is directly related to atmospheric structure of temperature, wind, and humidity in the vertical direction. Normally during daylight hours the temperature decreases with altitude at the rate of about five and one half degrees per thousand feet on a sunny day, and to somewhat lesser amounts on cloudy days. Consequently, sound travels slower with altitude because of the lower temperature, and the sound rays tend to bend skyward, and are soon dispersed in the atmosphere. Quite frequently, however, the temperature increases with altitude, and just the opposite effect is attained. That is sound rays are bent downward, and sometimes reach the ground with intensities approaching that at the source. When the temperature increases with altitude a temperature inversion is said to exist. Less frequently than these two atmospheric conditions a condition is observed where temperature remains constant with altitude. This is called an isothermal atmospheric condition, and sound passing through this type of atmosphere tends to travel in straight lines, neither bending upward nor downward. The sound will be greater than normal near the blast, but will dissipate rapidly with distance from the blast site with no zone or zones of silence.

Jan 1, 1962

By L. F. Nicolai, W. J. Schlitt

Lateral migration of leach solution in heaps and dumps is attributed to two phenomena. One is site-specific anisotropic conditions that exist on a macroscopic scale on the surface or within the rock piles. The second is associated with a random walk phenomenon that causes dispersion of solution, especially at gradients in flow or hydrostatic pressure. The latter phenomenon is a general condition that will occur in any leaching operation. Its effects are modeled by computer analysis and are compared with available field data on heap leaching. Under appropriate assumptions, the observed 58° angle of solution dispersion can be reproduced by the model. The combined effects of both anisotropy and random walk are also discussed. Finally, the impact of lateral solution flow on actual leaching operations is considered.

Jan 1, 1988

By B. C. Lewis

The mining industry has experienced a general trend toward an increasing number of longwall operations, an increasing percentage of underground coal being mined by longwalls, and increasing productivity from the longwalls. Longwall operators have not yet reached a state of mining euphoria. Competitiveness both within the industry and from alternate fuel sources is forcing continued pursuit of higher productivities and lower costs. The following graphics present trends in the industry. Longwall mines, as defined for this presentation, are those reportedly having longwall installations in each of the respective years. Production from both the continuous miner and longwall units is included in the longwall mines. Non-Longwall mines are all other underground mines. Productivity calculations are based on total employee-hours associated with the operation.

Jan 1, 1990

By Miroslav Cervenka

The Coal, characterized by coal quality parameters as for example, ash content (Ad), moisture (Wrt), heat content (Qr1), sulphur content (Sd) and other parameters is still in many countries the basic source of energy. Energy is life, especially in modern society, where the demand for ecologically clean energy is very high; and therefore, there is great importance in effective coal utilization Direct utilization - burning of coal for energy generation, is still one of the most effective methods. In most cases, it is one of the cheapest energy transformation methods in spite of the fact that this energy transformation is connected with the deterioration of our surroundings. Deterioration can be substantially reduced if the burning of coal at power stations, heat power stations and other coal consumers is optimized. That means the burning is done in steam boilers, the technical state of which is very good; the coal has minimimum .variations with respect to the projected values; and the burning process is controlled and checked not only from a regulation point-of-view but also from an ecological point-of-view. The instrumentation capable of measuring the characteristic coal quality parameters in real time exists and it forms the basic assumption for the work our research team has made. The proper application of this instrumentation is able to provide information for burning process optimalization. It is the main topic of this paper, which is the compilation of the information on our work -made during the last five years. The whole information is based on practical experience and applied systems in Czechoslovakia in the mines and power engineering industry. See [Cervenka, 1989]

Jan 1, 1992

By C. C. White

Although many notable scientific investigations relating to roof control have been made, roof control still must be considered one of the more baffling problems confronting the miner. Each year contributions are made to our understanding and techniques in dealing with various single phases of the overall problem, however, an equation considering all the variables involved in roof control, if formulated, would indeed be hopelessly complex. Among the factors to be considered is first, gravity which is always acting but which is sometimes less of a problem than lateral forces. There are lateral forces due to expansion, resulting from the weight of overlying rock; to these must be added lateral stresses of orogenic or tectonic orgin, which may be enormous. Stresses due to plastic flow of beds, water pressure, gas pressure, expansion due to absorption of water, faults, joints, fractures, pot heads, and the like may complicate the solution. Therefore, we must base decisions on roof control, and roof bolting in particular, largely on experience, and far too often on few "knowns" and many "unknowns", The development of "in situ" roof trusses may prove of benefit because, they unlike roof bolting, promise positive calculable roof support. These trusses require installation of steel tensioned rods in the roof, which rods are arranged to produce a stress pattern similar to a bridge truss, the roof rock acting to transmit the compression forces. The simplest form of truss (see figure 1) consists merely of two steel rods anchored at the back of holes drilled at an angle of approximately 45° over the pillars, collared near the the middle of the room, the lower ends of the rods being connected together by tierods and turnbuckles. Used in this way, a 3/4" diameter rod can offer greater support than a 10" x 5-3/4" wide flange steel beam. By tightening the turnbuckle, uplist on the roof can be produced,, the downward reaction being transmitted to the pillars by the rods. This simplest form of truss has been used in rooms up to 24' in width. Trusses of four panels, that is, consisting of a truss within a truss, as shown in figure 2, have been used successfully in rooms 30' wide. (figs 2 & 3) It appears a 6 panel truss could be used in a 40, wide room.

Jan 1, 1968