Search Documents

By Yi Luo

In a shearer longwall mining operation, the longwall bits are responsible for breaking into and chip-ping the broken coal blocks away from the coal face. However, underground observations have found that a large number of longwall bits are always working under various degrees of wear. Reduction of the bit wear could be realized by using better designed longwall bits and properly selected shearer operating parameters. A computer program has been developed to simulate the performance of the longwall bits. The shape of the bit head, the installation of the bits on the drum and the operation parameters are the information required by the program. Through the simulations, the main factors affecting the bit wearing process are identified. Suggestions are also made for improving the design of the longwall bits.

Jan 1, 1996

By Rainer Antretter

While respirable crystalline silica (RCS) dust that arises in industrial production mostly emanates from point sources and can be well mitigated, the extraction of dust is much more difficult in underground construction, since locally generated dust spreads widely. Analysis of dust measurements shows that RCS values are difficult to predict, and effective dedusting systems are required to comply with permissible exposure limits (PEL) in breathed air. Dedusting systems are effective near the tunnel face, while dedusting of working areas away from the tunnel face is difficult or even impossible. In general, there is little temporal influence on the tunnelling work—except for drill and blast excavation—which makes it necessary to remove the deduster and ductwork from the face area. Concurrent work in the tunnel is affected by the backflowing air mass of ventilation and therefore the quality of this air mass must be considered. The use of personal protective equipment (PPE), e.g., dust filter masks, is considered the least-desirable safety measure available. However, for certain individual operations in the tunnelling process, the use of PPE cannot be avoided, especially if other technical mitigation measures are not possible. In tunnels with small cross sections for example, dedusting systems often cannot be accommodated and PPE must be used instead. This raises the question of whether the use of PPE can be avoided by designing appropriate excavation cross sections and allowing for the implementation of technically engineered mitigation measures. The paper highlights problems with dedusting measures and shows possible ways to achieve OSHA compliance.

Jun 13, 2021

By J. H. Gasper

The overall success of steep slope (>20°) contour mining is dependent upon many factors. The major factor is the selection of the mining method that best suits the premining site conditions both environmentally and economically. These conditions can be divided into three major categories: 1) Geometric Conditions --machine limitations, slope stability restrictions, erosion capacity, among others; 2) Physical Conditions--material properties, rock strengths, diggability, driving surfaces, among others; 3) Chemical Conditions --acid/base relationships, blending or selective placement of overburden, among others. This paper incorporates these conditions through conceptually modeling compliance oriented contour mining methods; in particular Haulback methods, utilizing: 1) the Front-End Loader (FEL)/Truck; 2) Tractor Scrapers; and 3) Combined FEL-Truck/Scraper. Engineering analyses including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces), drainage requirements and many others can be performed after the geometric constraints dictated by in-situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views, but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By W. Burger

For the development of deep, hard rock, mines fast access to the orebody is critical. In some cases the mineralized area is more than 1,500 m (5,000 ft) below surface. Excavation of shafts or declines is typically on the critical path of the project schedule. Saving time on those activities can significantly increase the net present value of the mining project. Mechanical excavation methods are a step-change in excavation performance and labor safety compared to drill-and-blast operations. In hard rock conditions, roadheaders cannot be used effectively, so disc cutting is the first choice. For excavation of declines, tunnel boring machines (TBM) can be used in many cases. These provide, in certain rock conditions, considerably higher production rates com-pared to drill-and-blast excavation. Herrenknecht AG has developed a vertical shaft sinking machine (VSM) that is able to excavate shallow shafts in soil and medium soft rock. The ground is excavated by a roadheader boom. The muck is removed by a slurry system or a pneumatic system in combination with hoisting of skips. These machines have been applied successfully on shafts down to 100 m (300 ft). A pre-sink for a deep mine shaft has been excavated by this technology. For deep, hard rock shafts, a new shaft boring system has been developed by Herrenknecht AG in collaboration with Rio Tinto. Based on proven technologies, the system uses a unique arrangement of existing proven technologies. The system integrates excavation, mucking, primary rock support, installation of the final lining and shaft infrastructure. This new system improves the health and safety of shaft construction. Detailed performance estimates indicate significantly higher shaft construction rates are possible compared to conventional shaft sinking methods.

Jun 1, 2010

By W. G. Pariseau

Recent advances in rock-mass mechanics and computational technology now allow for the stability analysis of excavations in "wet" mines where mining-induced changes in rock mass deformation and fluid flow are coupled and time dependent. In addition to water pressure and flow in jointed, possibly porous, rock masses, all of the usual dry-mine parameters, including the premining stress state and rock-mass properties, are taken into account. Finite-element analyses of shafts and tunnels, as circular, elliptical, rectangular and arched-rectangular hole shapes excavated in an initially stressed and pressurized rock mass, indicate that the usual guidelines for optimum shape and orientation of single openings apply. Here, optimum means maximizing the minimum wall safety factor or, equivalently, minimizing the peak stress concentration. The results also show that failure originates in elements at the wall and the minimum safety factor at the wall in the wet case is always less than the dry case, regardless of drainage time allowed.

Jan 1, 1997

By V. B. Achanti

This paper deals with the effect of various bit geometric parameters on failure characteristics of rock material. Improvement of rock cutting efficiency of continuous mining machines has been an interesting research topic for the last few decades. In the current study, an automated rotary rock cutting simulator, duplicating a continuous miner, was utilized to study these parameters in the laboratory. Improvement of bit performance in terms of its life, cutting efficiency, dust production and energy consumption has drawn wide spread attention over the years. Research shows that optimizing bit parameters can result in efficient fragmentation of rock. Indiana limestone rock material was utilized in this study while bit tip angle, bit tip size, bit spacing, depth of cut and cutting velocity of rotary drum were varied to investigate the failure characteristics. The cutting pressure, penetrating pressure and the depth of cut were monitored on the simulator during the cutting process. Air borne dust and settled dust were measured for each experiment. Then, the specific airborne dust and specific energy were determined for the each type of bit. Triaxial tests were carried out to correlate the failure angle of the rock in static case to dynamic cutting process failure. The physical and mechanical properties of the rock were also determined in order to assess their influence on the wear characteristics of each bit.

Jan 1, 1998

By William C. Peters

"A large proportion of the earth's surface is blanketed by young sedimentary formations and by recent lava flows. How many Guanajuatos lie concealed beneath the rhyolitic capping of the Sierra Madre of Mexico? How many Kirkland Lakes are under the drift cover of the Canadian Shield? How many Wilunas are still hidden by the alluvium of the desert of Western Australia? How many ore deposits lurk underneath the basalt-covered plateaus of the Columbia River region? If erosion at Goldfield, Nevada, had stopped 100 feet higher, probably no ore would have been exposed. How many Goldfields are still awaiting discovery?" --Hugh Exton McKinstry, 1948

Jan 1, 1969

By Kevin Sierra, Orfelinda Avalo, Julio Guizado, Edwilde Yoplac, David Martinez

Mining tailings are slurry byproducts of mineral recovery. They generate serious environmental risks due to their toxicity when exposed to water and oxygen. Studies focus on eco-friendly alternatives for mitigating these environmental impacts. Processing these tailings enables a sustainable mineral production model through circular economy practices. This study evaluates using gold mining tailings to recover gold and produce bricks. Flotation tests obtained a concentrate with 86.66% gold recovery, containing sulfides (pyrite, arsenopyrite) and a tailing with silicates and oxides suitable for brick manufacturing and ornamental pieces. This approach promotes eco-friendly solutions and a greener approach to mining operations.

Feb 1, 2024

By A. Juganda, Jr. Bogin, S. Saki, R. Gilmore, J. Brune, J. Grubb, S. Lolon

"In longwall mines, atmospheric or barometric pressure fluctuations can disturb the pressure balance between the gob and the ventilated working area of the mine, resulting in a phenomenon known as “gob breathing”. Gob breathing triggers a gas flow across the gob and the working areas and may result in a condition where a methane accumulation in the gob flows into the face area forming an explosive mixtures. This paper discusses results of Computational Fluid Dynamics (CFD) modeling carried out to analyze this phenomenon and its impact on the explosive mixture development under a bleeder-ventilated longwall gob panel scheme. Modeling results indicate that the gas inflow and outflow across the gob and the formation of Explosive Gas Zones (EGZs) are directly affected by the barometric pressure changes. Methane gas and EGZs in the gob expand out toward the face and bleeder entries during the falling barometric pressure. Where methane zones interface with mine air, EGZ fringes may form along the face and in the bleeder entries. When the atmospheric pressure increases, an ingression of oxygen into the gob is observed that can also increase EGZs in volume. The findings from this study help assess the methane ignition and explosion risks associated with fluctuating atmospheric pressures. INTRODUCTION Methane explosions continue to be a daunting risk for underground coal miners, although the number of related fatalities and injuries in the U.S. coal mining industry has steadily decreased since the establishment of the U.S. Bureau of Mines in 1910. Still, the consequences of a methane explosion are often disastrous with multiple fatalities and property damage often leading to permanent shutdown of the mine. Methane is formed during the coalification process and is released from the coal seam to the mine atmosphere when the coalbed is disturbed by mining or natural causes such as earthquakes. If not properly diluted by appropriate mine ventilation, this methane may accumulate in the active mine workings and gob areas. Researchers at the Colorado School of Mines have developed numerical models showing how and where explosive methane may accumulate in gob areas. Historical mine explosions appear to show a connection between mine explosions and fluctuating barometric pressure as a result of stormy weather. McIntosh (1957), Boyer (1964), and Kissell et al. (1973) studied the influence of barometric drops on major coal mine disasters in the United States prior to 1970. Their statistical analyses found that a majority of these disasters occurred in the fall and winter months when the barometric pressures were influenced by unstable weather conditions and noted increased methane content in the mine workings during times of falling pressure. Studies conducted by Fauconnier (1992) and Hemp (1994) found similar connections between methane explosions and barometric pressure fluctuations in a majority of gas explosions in South African mines. Ten out of twelve major mine explosions with five or more fatalities in the U.S. after 1970 were found to have occurred during the months of November through April when barometric pressure swings were more abrupt and intense (Lolon et al., 2015)."

Jan 1, 2016

By Patrick McElhinney, Jacob Carr, Bruce Whisner, Cory DeGennaro, Jingcheng Li

Since 2016, electromagnetic interference (EMI) of personal dust monitors (PDMs) with magnetic proximity detection systems (PDSs) has been observed in underground coal mines. The EMI causes the magnetic field measurements of a PDS to change, which, in turn, alters the calculated location of the miner relative to the machine. Any altered location calculation can potentially cause the PDS to fail to warn a worker who is at an unsafe distance from the machine, arousing a serious concern on safety hazard caused by EMI in underground mines. The search for EMI mitigation strategies led to the development and use of large shielding pouches and boxes to hold the entire PDM to reduce its magnetic emission. Research on these pouches and boxes found that although they were able to reduce the emitted radiation from the PDM, they also disturbed the magnetic field of the PDS, affecting its performance. Researchers from the National Institute for Occupational Safety and Health (NIOSH) have focused on shielding internal PDM components rather than shielding the entire PDM. The PDM air pump motor is one of the PDM components that has been identified as a major source of electromagnetic radiation and has been selected for further study and tests. The measurements show that a small copper or aluminum foil enclosure can effectively reduce the magnetic emission of the motor by between 50 and 85% at 73 kHz. This study compares the test results of the air pump motor with various cost-effective shielding materials. The data provided in this paper can serve as a reference for shielding enclosure design of the PDM air pump motor to reduce its electromagnetic emission as one form of EMI mitigation strategy.

By S. G. Tough, H. J. Hignett

The Transport and Road Research Laboratory is carrying out tunneling trials at Chinnor, Oxfordshire, with a 5-m-diam, full-face tunneling machine. The work, which is for research purposes only, involves driving the tunneling machine through chalk with most of the physical characteristics of the machine and its power consumption closely monitered. At the Conference a film was shown about this work, illustrating both the tunnel construction and the research program.

Jan 1, 1974

By B. Pollack, L. G. Stevens

INTRODUCTION In other chapters of this volume many of the important technical aspects in the design of concentration and dewatering circuits have been discussed. This chapter will deal with the steps necessary to bring that information together in order to produce the specifications necessary to purchase the equipment and complete the design. It deals with the plant as a whole rather than just concentration and dewatering, since the steps are essentially the same. Prerequisites to Engineering Design Feasibility studies will have been completed and design parameters established prior to the start of the engineering design stages for a metallurgical plant. The data base for the feasibility studies will have included laboratory and/or pilot plant test work, historical data, proposed plant site data such as climatology, topographic mapping, geological and geotechnical information. These studies will have established the general project design criteria as well as the process design criteria leading to the preparation of preliminary flowsheet ( s) and/or alternative process flowsheets. These will have incorporated metallurgical and material balances, allowing identification of major equipment items, and development of preliminary plant site plot plans. Preliminary technical and economic assessments and recommendations will have been prepared during this phase for Owner's review and evaluation of the technical, physical, and cost effectiveness of the overall project and its component process, process facilities, and supporting facilities elements. After Ownert s approval and decision to proceed, the engineering design can be initiated, using the above information as the basis. Engineering Design Phase The engineering design of metallurgical plants and their elements are generally developed in two sequential stages, namely: (1) Basic ("Front end") Engineering Design (2) Detail Engineering Design Figure 1 relates these engineering stages to the entire program from feasibility through construction.

Jan 1, 1986

By S. B. Patton

A computer model, which quantitatively utilizes the relationship between the interactive and dynamic processes of methane drainage, mining, and ventilation, is presented. The model includes simulation of the coalbed methane reservoir for prediction of gas-emission rates under the influence of degasification wells and longwall mining, ventilation network-generation, and ventilation simulation. As mining progresses step-wise through the coalbed-methane reservoir, the ventilation network is created and subsequently simulated, iteratively determining fan requirements to safely reduce methane concentrations. The model can be used to quantitatively study the effectiveness of methane degasification on the ventilation system in a longwall panel.

Jan 1, 1992

By W. Jacobi, K. Eisfeld

The primary objective of dosimetric modelling for the inhalation of radon daughters is the evaluation of the dose distribution and of the mean dose to sensitive cells or target tissues in the respiratory tract which are assumed to be responsible for the initiation of lung cancer. The results of such dosimetric models are influencing the practice of radiation protection in a twofold manner: Firstly, they enable us to identify appropriate operational quantities for air monitoring and for the surveillance of individual exposures to radon daughters. Secondly, they can be used to derive secondary and operational limits for these radionuclides from the basic dose limits. The dose to target tissues in the lung from inhaled radon daughters depends on various physical and biological parameters: The unattached fraction of daughter atoms, the AMAD of the carrier aerosol for attached atoms, the geometry of the respiratory airways, the breathing conditions, the parameters for the retention and translocation of daughter atoms in the different lung regions, and the location of the target cells or target tissues, respectively. Therefore, dosimetric modelling for radon daughters has to include a sensitivity analysis showing the influence of these parameters. To meet these objectives we have recently described in a comprehensive report an improved dosimetric model for the inhalation of 222Rn, 22ORn and their short lived daughters (Jacobi and Eisfeld, 1980). In the following this model is shortly described and the main results are summarized. DOSIMETRIC MODEL [Model Structure]. For the geometry of the bronchial airways the model A of Weibel (1963) was used. Each bronchial generation i (i =0.1 .... 16) was considered as a separate compartment i, for which the following transfer pathways for radon daughter atoms were taken into account (see fig. 1): (1) the uptake by deposition (deposition probability wi); (2) the translocation by ciliary clearance (rate constant [A]i); (3) the transfer to blood by diffusion through the bronchial epithelium (rate constant [A]b). To distinguish between attached (Index a) and free (index f) daughter atoms each bronchial generation was divided in two subcompartments (i.a and if) with a transfer rate constant [a]s (ia- if) characterizing the desorption or dissolution rate of attached atoms in the mucus fluid. Thus for daughter atoms primarily deposited in attached form the transfer to blood is a twostep process with the rate constants [a]s and [A]b which were assumed to be independent of the generation number i. [Deposition]. The deposition probabilities wi in each bronchial generation were calculated on the basis of the laminar diffusion model of Gormley et al. (1949); however the deposition in the upper airways was corrected for turbulent air flow, taking into account the results of our deposition experiments (Martin et al., 1972). Figure 2 shows the resulting deposition probabilities per unit surface area of the bronchial generations for nose breathing at a rate of 20 1/min. The values for attached daughter atoms refer to an AMAD of 0.2 - 0.3 µm ([O]g =3) for the carrier aerosol; the deposition values for free atoms were derived with a diffusion coefficient of 0.05 cm2/s, assuming a prefiltration of 50% in the naseopharyngeal region.

Jan 1, 1981

By John Frostiak, Igor Gonzales, Kenneth G. Thomas, Ken Manning

The Pierina deposit was acquired in August 1996 when Barrick Gold Corporation purchased Arequipa Resources, a junior mining company with extensive land positions in Peru. At the time of acquisition, Arequipa ha.d developed two exploration tunnels and drilled 9 exploration holes on the property. Metallurgical tests, conducted on samples taken from the tunnels and the exploration holes indicated that the ore was amenable to heap leaching. Barrick's exploration team recognised from the outset, the potential of the mineralisation and convinced Barrick's senior management that this was indeed a world class deposit that should be pursued. On November 25, 1998, the fi was poured at Pierina, 27 months from the time of acquisition. During that period BmTick completed its exploration programme, prepared a development plan including capital and operating costs, production profiles and cash flow forecasts, and a schedule to develop a mine and construct a leach pad and gold recovery plant, including all supporting infrastructure. All permits and environmental approvals were obtained and all necessary land was acquired. The project was completed on schedule and under budget. This was the first greenfield mine development for Barrick outside of North America. This paper details, mainly, the research and development, engineering, construction and commissioning of the metallurgical process facilities.

Jan 1, 2000

By S. K. Kawatra

Various types of mathematical descriptions of the flotation process are used in the design of a full scale flotation circuit. Mechanistic descriptions developed under controlled laboratory conditions establish theoretical residence time requirements. Empirical models, describing flotation performance as a function of full scale operating variables, are established from one flotation system and applied to another hypothetical system. Problems of design by mechanistic modeling, such as scale up factors, can be alleviated if the model is developed from a full scale flotation circuit. However, the numerous uncontrollable variables encountered in a full scale operation would preclude the practical application of such a model. Incorporating empirical relations into the full scale mechanistic model will facilitate its effective use as a guide for flotation circuit design. A semi-empirical model has been developed that promises to offer a more effective means of flotation circuit design.

Jan 1, 1982

By Delbert L. Keenon

The principal concepts of computer control and automation have been successfully applied in industries world-wide, The enthusiasm generated by the proponents of computer control, and the apparent mystery enveloping the techniques of computer control, have caused attention to be focused on this infant industry from all quarters. Consequently, the motivation to "computerize" may be the hope that computers will solve all economic problems. The truth remains that not only have there been monumental successes, but there have been some colossal failures. This paper will attempt to outline a generalized guide to computer control and present methods for avoiding some of the major pitfalls. Since the investment required for computer control systems has been drastically reduced in the past year, small operations will likely find that computerized process control is attractive in areas where it has never been considered before, The discussion presented here is intentionally non-technical and directed towards those who may soon find they have a possible application for a control computer. The primary purpose of computer control is to reduce expenditure and increase profits by improving the quality of product, increasing the efficiency of operation, reducing the materials and man hours required or a combination of these. Success or failure to reach the desired goal depends, to a large degree, on a well-planned approach. This includes recognizing a possible computer application, properly defining the job which is to be accomplished, evaluating computer systems, selecting a capable manufacturer, and following through with sound systems engineering and programming.

Jan 1, 1965

By Ian M. Loomis, Keith G. Wallace

The Waste Isolation Pilot Plant (WIPP) is a U.S. Department of Energy research and development facility designed to demonstrate the permanent, safe disposal of U.S. defense-generated transuranic waste. The waste storage horizon is 655 m (2150 ft) below surface in bedded salt. To date the WIPP project has not emplaced any waste. There are three intake shafts used to supply air to the underground. All air is exhausted though a single return shaft. The total design airflow during normal operations is 200 m3/s (424,000 cfm). The ventilation system is designed to provide separate air splits to construction, experimental, and storage activities. Separation is achieved by isolating the storage circuit from the construction or experimental circuits with bulkheads. Any air leakage must be towards the storage area of the facility. Field studies have shown that the pressure differential necessary to maintain the correct leakage direction is susceptible to the effects of natural ventilation; therefore, extensive studies and analyses have been conducted to quantity the natural ventilation effects on the WIPP underground airflow system. A component of this work is a monitoring system designed to measure the air properties necessary for calculation of the natural ventilation pressure (NVP). This monitoring system consists of measuring dry bulb temperature, relative humidity, and barometric pressure at strategic locations on surface and underground. The psychrometric parameters of the air are measured every fifteen minutes. From these data, trends can be determined showing the impact of NVP on the ventilation system during diurnal variations in surface climate. Both summer and winter conditions have been studied. To the author's knowledge this is the first reported instance of automatic and continuous production of time and temperature variant NVPs. This paper describes the results of the initial monitoring study. INTRODUCTION The ventilation system at the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico, is designed to perform two distinct functions. First, it supports normal mine ventilation requirements complying with all state and federal mine regulations. Second, the system is designed to prevent an uncontrolled release of radioactive contaminants from the storage and transportation areas of the facility. Although a nuclear radiation release in the facility is considered unlikely, many special features are implemented in the ventilation system to prevent the possible spread of contamination. The facility is constructed with the waste transportation and storage areas separated from the mining and non-radioactive experimental areas. The ventilation system is designed such that air leakage is from the mining and experimental areas to the storage areas. Furthermore, radiation detectors are located throughout the storage and waste transportation areas underground and an exhaust filtration building is installed on surface to prevent the possible release of radiation to the environment. For over two years the underground ventilation system has been rigorously tested and balanced. It was during this period that the adverse effects of NVP were noticed and subsequently quantified. From extensive field studies and computer models, several mitigating features were designed and constructed and special operational procedures were implemented to control the impacts of NVP. To quantify more accurately the NVP at the WIPP, a continuous monitoring system was installed. This monitoring system consists of measuring dry bulb temperature, relative humidity, and barometric pressure every fifteen minutes at strategic locations on surface and underground. From this psychrometric data, the NVP is calculated. Fan operating pressures and flows and strategic differential pressures are recorded from the site Continuous Monitoring System (CMS). The monitoring system provides a means of evaluating how the ventilation system behaves in regard to climatic conditions and to judge the efficacy of the mitigating features and operational procedures. To the author's knowledge, continuous calculation of NVP as a function of time and surface temperature has not been previously reported. Overview of the Waste Isolation Pilot Plant The U.S. Department of Energy determined that the plastic nature of bedded salt may provide the best solution to isolate transuranic (TRU) waste from the biosphere. Initial evaluations at the WIPP site began in 1974. In 1979, the United States Congress enacted Public Law 96-164 for the construction and development of the WIPP project. The mission of the WIPP is to demonstrate the safe, long-term disposal of TRU waste generated by the national defense programs of the United States. TRU waste is classified as a low to medium level waste. The waste is stored in drums and does not produce significant heat (not greater than 1 W per drum). The WIPP site is located approximately 47 km (29 miles) east of Carlsbad, New Mexico in the Chihuahuan Desert. The repository is located in the 630 m (2000 ft) thick Salado Formation. This Permian Basin salt deposit is about 225 million years old and appears to have been minimally disturbed by earthquake, faulting, and ground water activity since it was deposited. The underground facility is 660 m

Jan 1, 1993

By B. J. Arnold

Coal froth flotation cells typically receive little attention in coal preparation plants. They process only a small portion of the total coal feed (perhaps 5-1 0% of the total plant feed in the United States), they are viewed as a way to take the load off the refuse thickener, and their operation is not well-understood by cleaning plant operators. Operating parameters are set based on the equipment supplier information, and reagent dosages are set at the recommendation of the latest chemical vendor. The cells then operate day in and day out, recovering coal and producing a product that may not meet ash or sulfur specifications or that may be the wrong percent solids for downstream dewatering operations. If improvements can be made to this circuit, then the whole plant will benefit. Paying attention to rate and residence time and the wealth of data from the literature or from a series of targeted laboratory tests can give operators the key to improving the performance of froth flotation cells AND overall plant performance. This paper provides an overview of froth flotation rate and residence time data and gives practical suggestions for specifying and using laboratory tests to improve froth flotation performance. Suggestions for improving froth cell performance are also given based on available literature data.

Jan 1, 1999

By Christian F. Baiz

The author will present a discussion of the steps which must be taken by the prospective developer of a small mining operation to establish technical credibility when seeking financial backing. Particular emphasis will be given to the differing levels of technical work (and their relative cost) which must be accomplished to supply the information necessary to satisfy potential investor groups, whether they be other mining companies, equity investors, or financial institutions such as venture capital firms or commercial banks.

Jan 1, 1981