Search Documents

By C. R. Euston, B. T. Field, W. E. Lindquist

Pyroprocessing applications in the minerals industry range from low-temperature drying to high-temperature reactions. Material characteristics and process requirements range over a very broad spectrum and can confuse plant engineers trying to select a pyroprocessirtg system for their plant. This paper examines the important process variables and offers empirical guidelines to assist in a user's overall process evaluation.

Jan 1, 2000

By C. M. Brown

Common operating philosophies and objectives of mining and mineral process operations are discussed. Key information required to effectively monitor operations is reviewed in conjunction with the impact of external variables such as commodity price changes on strategies adopted.

Jan 1, 1991

By C. P. Mangelsdorf

Introduction During the 13 years since C. C. White introduced the Birmingham roof truss there has been a revolution in permanent roof support technology. While not all of the emerging concepts have their origins in the truss-resin bolting is a prime example - the combinations and permutations of devices presently available to the underground mining industry reflect a well-spring of creative activity. The purpose of this report is to chronicle a number of roof support system that have same physical similarity to the Birmingham truss, and to report on their application. Definitions The application of the tern "truss" to the device developed by White of the Birmingham Bolt Company in 1967 may be derived from the classical technique of stifwood, by the attachment of an underslung, sometimes pretensioned metal strap, rod or cable. If the beam is separated from the reinforcement by a single block or vertical post it is called a "King's Post Truss". If two equally spaced blocks or posts are used it is referred to as "Queen's Post". When the immediate roof of a mine is visualized as a beam, the Birmingham device completes a structure resembling this latter form.

Jan 1, 1982

By Robert B. Tippin

A number of recent studies 1-4 suggest that steelmaking expansion might be achieved more economically by a combination of the prereduction furnace and the electric steelmaking furnace rather than through new blast furnace construction. Supergrade concentrates would be the first step in an evolving technology which bypasses the blast furnace and in which the concentrates are first made into pre¬reduced pellets and then used directly in electric steelmaking, Prereduced pellets made from superconcentrates should not only be competitive with scrap, but should be a preferred feed for the electric furnace because of the absence of such residual elements as copper and nickel. Furthermore, geographic areas remote from present steelmaking centers may find the electric furnace to be an economical method of providing local steel requirements. The development of successful methods of producing superconcentrates may also be expected to find application to conventional blast furnace burdens. The need for methods of increasing grade of domestic concentrates will become increasingly urgent in the face of competition from high grade imports. Only a small percentage of domestic iron ore production can qualify as superconcentrates, (Superconcentrates for the purpose of this investigation are limi¬ted to those concentrates which contain a maximum of 2 percent S'02). During the last several years the Twin Cities Metallurgy Research Center of the Bureau of Mines has directed research efforts to develop methods of manufacturing superconcentrates from present standard grade products by cationic flotation, screening, and magnetic separation.

Jan 1, 1971

By J. B. Gwiazda

In designing mine workings and adequate roof supports, it is indispensable to determine properties of the strata surrounding the workings. The proper selection of roof supports is based, before everything else, on a thorough knowledge of the roof rock strength, especially tensile strength. This parameter is a vital factor in the delamination of roof rocks and eventual cave-in. It is also important to know the properties of the floor on which the roof supports are set. While driving galleries, it is essential to know beforehand the strength of rocks that will be encountered in the near future during the work. The devices described will help to obtain this information.

Jan 1, 1987

By C. J. Savage

Rio Tinto Minera, S.A. operates in Southern Spain, at one of the most ancient mining sites in the world, using advanced computerised mine planning. This paper describes the development and application of the mine planning systems to the copper and gold/silver operations. It briefly covers the hardware configuration, and the advantages and improvements in mine planning achieved. The system's application started with the long term mine planning of Cerro Colorado (open pit) copper mine and was gradually extended to cater for the medium and short term planning requirements of the other operations of the Company. The base of the system is a mineral inventory established by the combined use of the geology and geostatistical methods, and compatible with the mine planning requirements. The planning system has three major components: one used for open pit design and long term mine planning, another used for blast evaluation and finally one used for short term mine planning. Recently, a fourth component has been added to the system for reconciliation between predicted and actual tonnages and grades. There is common data file transfer throughout the system.

Jan 1, 1986

By Lewis L. Oriard

The authors outline the development and application of blasting methods put into use 11 years ago at the Berkeley Open-Pit Mine, Butte, Montana. The blast design uses a very short delay (5 milliseconds) between detonation of explosives charges, a feature challenged several times in principle despite its success for Anaconda. Concern is expressed over the categorical rejection of very short delay blasting which can make the difference between success and failure of major mining operations. There is ample evidence to show that the method can be used successfully and not violate the concerns of the public.

Jan 1, 1980

By R. Sandrik

Northwestern Resources Co. (NWR) was established in 1972 as a wholly-owned subsidiary of Western Energy Company of Butte, Montana, to acquire, explore, develop, and produce energy resources outside the state of Montana. Western Energy is a coal mining company with successful operations in Montana and Wyoming. In 1974, NWR acquired its first lignite lease in Texas. NWR eventually acquired a large leasehold in central Texas, which was identified as having a high potential for future production. In 1979. NWR contracted to supply lignite to Utility Fuels, Inc. (UFI), a fuel affiliate of Houston Lighting and Power Company (HL&P). This project, together with leases held by UFI, became the Jewett Mine. Lignite from the Jewett Mine is used as fuel at the adjacent HL&P Limestone Electric Generating Station, at an annual rate of approximately 7.3 Gkg (eight (8) million tons) per year.

Jan 1, 1991

By Gary Buchan

During several months in 1996 and 1997, Cyprus Twentymile Coal Co. (TCC) set world production records at its Twentymile Mine in northwestern Colorado. These records were due to the company's implementation of a state-of-the-art longwall mining and conveyance system along with a -highly dedicated work force. This article is a case study of the design of long panels at the mine from conception to implementation. Obstacles that needed to be overcome included subsidence engineering, environmental regulations, conveyance, ventilation, equipment design and continuous miner (CM) development timing.

Jan 1, 1998

By H. Kempton

New methods for remediating metals-contaminated groundwater include in-situ emplacement of highly adsorptive substrates to permanently retard solutes. Substrates are introduced by sequential injection of soluble components that precipitate in the aquifer, forming a permanent high-retardation zone. This method overcomes the factors that limit pump-and-treat remediation; i.e, long-term source loading and slow desorption. Column tests demonstrated efficient substrate emplacement, increasing retardation coefficients of Cr(VI) by 20 and As(V) by 40. Similar effectiveness is expected for other heavy metals. Simulations using a coupled advective-geochemical model accurately matched substrate emplacement and arsenic attenuation, allowing extrapolation to other constituents and larger-scale applications.

Jan 1, 1999

By F. M. Doyle, J. P. Dwyer

Introduction The mining industry has a poor public image. It is often perceived as a despoiler of the landscape and a polluter of the environment, and there is little recognition of societal needs for the raw materials and fuels that this industry produces. There are many reasons for this poor image, but an important one is that a substantial number of mining operations have caused significant damage to the environment. Many of these operations, particularly those that now are abandoned, continue to have an adverse impact, principally in the form of water pollution.1 In some cases, the damage caused by this pollution extends well beyond the immediate region around the mine. Chemical contamination of ground and surface waters can, and does, occur in nature when these waters flow through or over undisturbed, mineralized rock masses. However, the problem is greatly exacerbated by mining because the mining activities increase, by several orders of magnitude, the permeability and the surface area of rock that can be contacted by percolating water. Water flowing through either the mine workings or the waste rock dumps becomes contaminated. Pollution can also arise if leachate from tailings ponds enters either groundwater or surface waters. This leachate may contain chemicals used in processing the ore. The magnitude of the threat posed by mining wastes depends on the type of minerals in the deposit, and on the chemicals used to process the ore. The magnitude of the threat also depends on two other, site-specific factors. One is the volume of water flowing into the mine and through the dumps, which depends on rainfall patterns, topography, and whether the mine workings are surface or underground. The other is the proximity of the pollution source to groundwater or surface waters, which depends on both the climate and geology. These factors influence the concentration and the quantity of polluted water forming and reaching the receiving water. Mining activities present a potential problem of enormous scale. Vast amounts of rock are mined each year2 and, as noted above, substantial problems have arisen at some mine sites. These problems are usually exceedingly costly to address, and it is imperative that these mistakes not be repeated. There are indications that we can accomplish this goal; we now better understand the processes that cause pollution and have methods to prevent or contain it. In addition, in the past few decades society has started to recognize the need for all industries to operate in a manner that maximizes the health and safety of workers and the public and minimizes adverse environmental impacts. A variety of recently enacted federal and state laws regulating public health and environmental hazards reflect the increasing concern over these issues. Many statutes, such as the federal Clean Air Act and the Clean Water Act, encompass activities undertaken by the mining industry. Other laws, such as the Surface Mining Control and Reclamation Act, have been written to regulate specific hazards posed by this industry. At the present time, the federal government. through the Environmental Protection Agency (EPA), and several state governments, are preparing new regulations specifically tailored to control the disposal of mining wastes. Given the magnitude of the potential environmental and health risks posed by disposal of mining wastes and the regulatory costs to the mining industry (both of which are due to the tremendous volume of waste generated), it is especially important that regulators have a good understanding of the different types of mining wastes and the risks they are likely to pose in various geographic and climatic circumstances. Only then can a regulatory program be designed with suitable procedures and substantive criteria to protect the environment and ensure compliance, while avoiding unnecessary or wasteful expenditures. California has long enjoyed a large, active mining industry. Today it produces a wide range of mineral commodities. The revenue from production of non-fuel minerals in California ($2.85 billion in 1988) greatly exceeds that of any other state. About a third of this revenue is from the production of inert sand, gravel and crushed stone. However, the remainder is from the production of a wide range of materials. These include boron minerals, rare earths, asbestos, talc and pyrophyllite, and gold. In earlier decades, an even broader range of minerals was produced, including mercury, copper, lead, zinc, and barite. There are acute environmental problems at some of these early mine sites. Because in 1987 the state of California was engaged in a revision of its regulations for mining waste disposal, the legislature commissioned a study by researchers at the University of California at Berkeley to investigate and review: the magnitude of the problem posed by these wastes, • the best feasible control measures available for waste management and disposal, • the problems of abatement and cleanup at so-called "problem" mine sites, • the current regulations imposed on mining waste disposal by various federal, state, and local agencies and the effectiveness of these regulations. This paper summarizes the principal findings from this study (Mining Waste Study, 1988). The lessons from this investigation are likely to be of general interest because of the diversity of mineral products produced, and the wide range of geographic and climatic conditions encountered. The acute problems seen at some of the older mines are typical of the western United States, and teach useful lessons on strategies that should be implemented at new mines to prevent recurrences of these problems.

Jan 1, 1992

By A. John R. Hart

INTRODUCTION In each given set of operational criteria for tunnel design, ground conditions dictate the selection of the most appropriate construction method and tunnel lining. The designer has the responsibility to choose or restrict the choice of the tunnel lining to insure that the final solution provides a cost-effective permanent construction which will require the minimum of maintenance and endure to the benefit of future generations. This Paper deals with some of the aspects of precast concrete tunnel linings, their history and development through the years. It does not purport to be a comprehensive review of all that has ever been tried or developed but, hopefully, a starting point to encourage discussion and development for the future. BOLTED LINERS As a result of anticipating a shortage of cast iron tunnel lining in 1936 when work was proceeding on London Transport's Central Line Metro, a design for the precast reinforced concrete bolted lining was born. The design took the form of the traditional cast-iron lining but with substantial concrete stiffeners to take the shield ram forces. This new lining was used to construct some 14,000 feet of running tunnel using a ring width of 1'8" which was the standard cast-iron width of the time. (Groves, G.L., 1943)

Jan 1, 1987

By Sheldon P. Wimpfen

Back in 1970 Congress passed the National Mining and Minerals policy Act, which had as one of its basic tenets to rely on a strong and stable private minerals industry for the development and production of our mineral resources. Since then, a substantial amount of legislation has been introduced that impacts on the minerals industry. Although most of the bills proposed are not passed into law, each bill affecting minerals and mining is given careful review by the Bureau of Mines. Comment is forwarded with the object of being helpful to legislators by providing our assessment of the probable impact of each bill proposed along with suggestions to improve them. Actually few bills introduced become law. For example, in the 93rd Congress 4,260 bills were introduced in the Senate and 17,690 in the House. In the final accounting there were passed 123 private laws and 649 public, 3 percent of the bills introduced. There would be little merit here in attempting to analyze each mineral-related bill that was proposed. Many are similar and aim at making a certain aspect of our minerals activity fit needs. So, to simplify the task the many bills have been grouped by subjects. Slide 1 shows the principal topics and the number of related bills introduced. Putting it altogether, there are 26 principal subjects and almost 200 bills. And these numbers are probably off somewhat, as this accounting was made early in December.

Jan 1, 1976

Some basic terms used in cost management and accounting include: - Cost. A sacrifice made to acquire goods or services, measured by the price paid. Technically, the sacrifice is called a cost until the benefits from the goods or services have expired, at which time the sacrifice is called an expense. In this text, the terms "cost" and "expense" are used interchangeably. - Revenue. An increase in the value of the firm resulting from the sales of goods and services. - Income. The excess of revenues over costs for a specified period. The term is often used with modifiers to indicate specific quantities on an income statement (e.g., pretax income; net income). - Activity. A measure of production work. Traditionally, physical production volume (tons of ore or units of product) has been used as the measure of activity. Other measures include direct labor hours, equipment operating hours, and quantity of materials or supplies consumed. - Responsibility center. A segment of an organization that is responsible for a specified set of activities. In mining, individual operating divisions can be treated as responsibility centers, known as profit or cost centers. Departments within a division are generally treated as cost centers. - Cost center. A portion of an organization having responsibility for achieving specified levels of cost. - Profit center. A portion of an organization having responsibility for achieving specified levels of profit (revenues and costs).

Jan 1, 1999

By Firoze E. Katrak, John R. H. Black, Paul R. Ammann, Michael J. Loreth, Servi. Italo S.

Germanium is produced primarily as a by product from zinc concentrates. The important sources of gallium are alumina ores (bauxites) and zinc concentrates and residues from zinc processing. In addition, gallium as well as germanium may soon be recovered from a depleted copper mine near St. George, Utah. The major uses for germanium are in semiconductors, lenses in infrared optical systems, catalysts, and gamma radiation detectors. The major markets for gallium are in light-emitting diodes, solar cells, laser diodes, integrated circuits, microwave devices, and magnetic bubble memories. CRA projects a healthy growth in the demand for both metals. However, the role of scrap metal will continue to be important over the next decade, thus decreasing the overall demand for primary gallium and primary germanium. This paper summarizes the key elements and the economics of the markets for germanium and gallium. Much of the information, such as plant-by-plant costs of production and estimates of consumption by end use for various countries is from proprietary databases of Charles River Associates.

Jan 1, 1986

By D. B. Stephens

Assessing the occurrence of natural ground-water recharge at mine and mill waste disposal sites may be crucial to addressing regulatory agency concerns regarding the potential impact of waste seepage on ground-water resources. Recharge has been shown to occur even in semi-arid areas where annual lake evaporation exceeds precipitation. Permanent storage of waste seepage in the unsaturated zone is not to be expected if recharge occurs under natural conditions. Establishing the direction and rate of fluid movement in the vadose zone by field measurements is an important element that should be included in the site selection process.

Jan 1, 1987

By Dennis Dolinar

Improperly designed support systems have led to unplanned roof falls in longwall tailgates. To prevent such falls requires appropriate support and adequately designed support systems. The National Institute for Occupational Safety and Health (NIOSH) is currently developing a standing support design methodology based on the ground reaction curve. To design the support system with this methodology requires a quantitative assessment of the ground and support interaction, which is developed from instrumented test sites installed in longwall tailgates. To compliment and expand the field data results and to optimize the support design, numerical modeling is also conducted. The models are calibrated from the test site data. In the present study, data was obtained from a longwall tailgate in the Illinois basin. The test site was located in the Herrin No. 6 coal seam at a depth of 500 ft. At the site, the immediate roof was a weak shale overlain by a competent limestone. Above the limestone, sandstone formed the intermediate roof. The floor consisted of a weak underclay. In the study, the performance and interaction with the surrounding rock mass of two different standing supports, an engineered crib and a conventional 4-point wood crib were monitored. The two cribs have similar load-displacement characteristics at least through 6 in of displacement. Beyond 6 in, the engineered crib becomes unstable and begins to strain soften and shed load. The measurements and developed ground reaction curves indicated that the tailgate at the mine was a low convergence environment until well inby the face. Because the convergence was well below their capacity, both supports provide more than adequate levels of support to the tailgate. Significant convergence and support loading did not occur until 90 to 100 ft inby the face. The results of this study were also compared with results from similar studies conducted in the Pittsburgh seam to further advance the development of the ?ground reaction curve? based support system design.

Jan 1, 2009

By M. A. Ackerson, R. E. Griffin, W. H. Pomroy

Two automated fire detection system configurations have been used successfully in underground mines: the pneumatic "tube bundle" approach and the electronic telemetry approach. The electronic telemetry approach is more widely used, owing to its greater speed, flexibility, and capacity to both monitor other underground conditions, and remotely control underground equipment. However, depending on specific mine conditions and layouts, pneumatic detection, or a combined pneumatic/telemetered system may offer significant advantages over the telemetered approach alone. This paper describes research by the U.S. Bureau of Mines to design and in- mine test a rapid response pneumatic fire detection system tailored to the unique requirements of multilevel metal mines. The relative merits of pneumatic detection are discussed in the context of typical multilevel mine layouts and environments. A Bureau developed proto- type system is described with emphasis on design features which counter commonly perceived and/or experienced pneumatic detection system operating problems. Finally, the results of a 3-yr in-mine performance evaluation of the prototype hardware are discussed. Included are descriptions of system layout and coverage, response time, tube leakage, sample dilution, elimination of accumulated water from sample lines, and system maintenance and reliability.

Jan 1, 1989

By E. C. Speers

The Ray Mines Division has a long and illustrious history beginning in 1911, as one of the early underground block caving copper mining operations. The tonnage mined from the beginning of operations, increased from about 8, 000 TPD in the early years to the present daily tonnage of 22, 500 tons, mined by open pit methods. The Ray basic milling practice has been relatively unchanged since 1927 when the sulphide-flotation process was introduced at Ray. The leach-precipitation-flotation process introduced in 1956 has been the only major process change. The change from underground to open pit' mining was accompanied by a renewed drilling and exploration program which developed large tonnages of low grade copper ores both in the porphyry and the diabase. The ore bodies as outlined were of such a grade and size that it soon became apparent that economical operations could not be developed with the lower tonnage rate. Also that in order to develop these newly proven ores, it would be necessary to move the Ray crushing plant, the Ray. supporting shops, offices, a substantial part of the Ray townsite, and would also involve the rerouting of Mineral Creek, a typical Arizona stream which is dry most of the year but can flow as high, as 8, 000 second feet in the rainy season. This paper describes those changes in flow sheet made necessary both by the increased tonnage .and the requirement to move as much of the crushing facilities from the Ray area as practical in order to free the mine for the extension of its physical limits.

Jan 1, 1961

By Peter J. Alderson, M. P. Evans

The application of conveyor belting in bulk materials handling is crucial to the success of most mining enterprise selection of the cover rubber grade and thickness has a direct bearing on the cost per ton conveyed. Current and future demands placed on belt covers by higher speeds, increase capacities and greater lifts means today's cover will not be adequate for tomorrow's applications. The simple selections of RMA Grade I and I1 and MSHA above and below ground need to be expanded upon. This paper describes various new approaches for selecting conveyor belt covers for specific applications. It also presents examples of material and compounding techniques available to the belt manufacturer to improve the performance of their covers.

Jan 1, 1996