Search Documents

By Alan T. Nelson, Ronald D. Mariani

The Tilden concentrator was originally constructed in 1974 for the processing of low grade hematite. Flotation is a key concentrating process in the operation, and therefore flotation optimization has been a major concern since the plant startup. This paper will discuss some of the modifications made in the process to achieve optimization. The conversion that now enables the plant to process magnetite as well as hematite also will be discussed. INTRODUCTION The Tilden Mine, located in Ishpeming, Michigan, is managed by Cleveland-Cliffs Iron Company and is owned by Cleveland-Cliffs and two Canadian steel makers. It was constructed and started production in 1974 and expanded in 1979 for processing a low grade, fine-grained hematite iron formation for which there was previously no technology available. Several papers have been written describing the unique character of the concentrating operation. The hematite plant consists of 12 grinding and concentrating lines, which utilize two stages of autogenous grinding with crushing of an intermediate sized product. The ground product is deslimed in a highly dispersed alkaline environment to reject silica. Corn starch, the flocculant, has a high affinity for iron at the operating pH range of 10.5 to 11.0. The ore is upgraded from 35% to 45% iron in the desliming step. The deslime thickener underflow is the feed to flotation. Each flotation line consists of a bank of 10 rougher cells, followed by four scavenging banks incorporating 5, 4, 3, and 3 cells each. The Wemco flotation cells are each 14.1 cubic meters (500 cubic feet) in volume. A total of 12 flotation lines are available. [ ] A reverse flotation process is employed, using a straight-chain, 8 to 10 carbon primary ether amine silica collector. At the levels used in the circuit, the amine also serves as a frother. A final concentrate is produced in the rougher cells. The concentrates from the four scavenging steps are combined and recirculated to the feed end of the roughers, with the fourth scavenger froth being discarded as a final tailing. Upgrading to about 65% iron is achieved, with control of the circuit based on final concentrate silica grade. Starch is again used, this time as a depressant for iron. During the years of operation, several key areas of the flotation process have been targeted for optimization. The most significant improvements have been realized in the following areas: *Grade Control Automation *Control of Water System Chemistry *Flotation Spray Water This paper will focus on these areas, but other minor improvements also will be briefly discussed.

Jan 1, 1993

By J. C. Stankus, S. S. Peng

Many coal seams are associated with soft floor strata. During mine development, if coal pillars are not properly designed, floor heave occurs and causes interruption of coal production. In the severe cases, the section or mine is abandoned. One method for controlling floor heave is floor bolting. This paper describes the demonstration of flour bolting methods in a West Virginia, info coal mine. Three methods were used: vertical full resin bolting, floor truss bolting and floor truss bolting pins a floor slot at the center of the entry. The design of each method and the experimental results are discussed.

Jan 1, 1995

By Carl Hansen

Sonora Mining Corporation (SMC) operates the 6,000 tonne per day Jamestown open pit gold mine in the Mother Lode district of California. The mine has been in operation since January, 1987, and has produced approximately 7,800 kilograms of gold since start-up. The property consists of five ore bodies lying along a five kilometer stretch of the famous Mother Lode vein system. At present, only the Harvard ore body is being mined. The Harvard pit is centered around a historic underground mine of the same name that was operated from 1896 to 1916. The present ore body averages 2.5 grams gold per tonne as free milling gold and auriferous pyrite. The project consists of the open pit mine and concentrator complex in Tuolumne County, California, and a carbon-in-pulp leach plant located near Yerington, Nevada.

Jan 1, 1990

By W. Pariseau, J. Goris, S. R. Dismuke

Ore at the Magmont mine in southeast Missouri is extracted by the room-and-pillar method on two and sometimes three horizons. In 1991, a plan was formulated to recover high-grade ore in pillars using cable halts to accommodate spans of more than 27 m (90 ft ). A test area was selected and a recovery plan developed. A cooperative rock mechanics study was established by Cominco Metals, the US Bureau of Mines and the University of Utah. When initially opened in 1968, the planned production rate was about 910 kt/a (1 million stpy). Due to declining reserves, the production rate was decreased in November 1992 to 570 kt/a (630.000 stpy). Pillar recovery now accounts for about 40% to 50% of the mined tonnage. This method plays a vital role in allowing Magmont to continue to operate.

Jan 1, 1996

By Robert E. Gray

The vat leaching operation at the Yerington Mine was started in October, 1953. The original plant facilities consisted of primary and secondary crushing, eight leaching vats, precipitation launders, sulfuric acid plant and the necessary maintenance, warehouse and administrative facilities. By 1961, 35,000,000 tons of oxide ore had been removed from the mine exposing the underlying sulfide ore body. A 5,000 ton per day concentrator was constructed and put into operation to treat the sulfide ore in November, 1961. The original crushing plants were used for both oxide and sulfide ores. By adding a third crushing shift for six days per week, the treated ore was increased from 12,000 to 17,000 tons per day. To balance the oxide and sulfide ore reserves, the concentrator was expanded to 13,500 tons per day in 1967. Again, no additional crushing facilities were added. It was anticipated that the treatment rate of oxide ore would be reduced from 12,000 to 9,000 tons per day. Instead, the addition of two crushing shifts per week, and improved operating procedures, increased the treated ore to 26,500 tons per day, 13,000 tons to the vat leaching and 13,500 tons to the concentrator.

Jan 1, 1975

By J. C. Motz

During the past five years, Rexnord has developed, tested and introduced the Nordberg Omnicone Crusher to the industry. When the Symons brothers invented the cone crusher over 60 years ago, they employed the principle wherein the length of the crushing stroke was related to the free fall of material by gravity. This permitted the material being crushed to fall vertically in the crushing chamber; and in effect, caused the particles to be crushed in a series of steps or stages as the particles got smaller due to the crushing action. This also helps to reduce the rate of wear of the liners since the sliding motion of the particles is minimized.

Jan 1, 1986

By L. G. Wilson

In order to comply with time limitations imposed by this symposium, a very narrow but nonetheless interesting segment of the market has been chosen for discussion of the preparation of a tailor-made product to meet a specific need, and in view of the fact that the barite market is one of the oldest and one of the broadest non-metallic mineral markets in the world, it is necessary that we place this in perspective. Of a recent world annual production; (i.e., 1966 figures released last year in MINERALS YEARBOOK), of some four million tons, the United States consumed over 1/2 million tons, of which approximately 950,000 tons were produced domestically and approximately 700,000 tons were imported. Of this total, something approaching 90% was used for drilling-mud weighting, and of the balance, all but about 60,000 tone is consumed in the production of glass, barium chemicals, aggregates, and other minor uses; thus we are really taking a look at a very minute, however important, and very selective, portion of the total barite-market. The real meat of this paper, after eliminating all irrelevant uses of barite, and delineating the area of discussion, resolves itself into the approach to a favorable marketing area and a specific attack on that area. Cost, to the user, has been, patently, a function of distance, as the basic price of barite has varied very little over the years until recently, and freight rates have been the governing factor. Conversely, the seller of barytes must make concession in the plant price to compensate for distance, if he is to successfully compete.

Jan 1, 1969

By Salt Lake City Research Center, D. G. Foot, J. D. McKay

As part of its research program on column flotation, the Bureau of Mines, Salt Lake City Research Center has performed studies on (1) column flotation amenability and comparison with conventional flotation results for over 15 mineral systems, (2) alternative methods for improving column bubble generation systems, (3) mineral behavior within a column, and (4) the effect of changes in column operating parameters on flotation grade and recovery. Based on results from these studies, flotation columns (1) are capable of producing higher grade concentrates in fewer stages than conventional flotation cells at equivalent or increased recoveries, (2) require less retention time than conventional flotation cells, and (3) can be divided into cleaning and collection zones that have characteristic mineral-upgrading-per-foot values. Attempts to improve the column air sparger have led to the development of a superior external bubble generation system, which can (1) achieve increased air holdups. (2) produce bubbles from 400 Um to 4,000 Um average bubble diameter with minimal frother addition, (3) provide superior bubble size control, and (4) be maintained without column shutdown. Efforts are continuing to improve column flotation and transfer successful technology to industry.

Jan 1, 1988

Using a Mark IV surface force apparatus, adsorption of dodecylamine hydrochloride on mica has been studied at pH 5.7 in the presence and absence of octanol. With amine alone, the repulsive forces between mica surfaces are reduced due to charge neutralization and attractive hydrophobic force; however, the latter is of relatively short-range with its decay length less than 2 nm. In the presence of amine and octanol, the hydrophobic force becomes more significant, its decay length being extended up to 6.5 nm. The increased hydrophobicity in the presence of octanol is attributed to the co-adsorption of the neutral surfactant with dodecylamine, which increases the packing density of hydrocarbons on the mica surface. The increased hydrophobicity due to co-adsorption is reflected in the improved floatability of silica when using octanol as an extender.

Jan 1, 1993

By Vanessa Viterbo, Lia Walker, Hassan Khaniani, Vitor Viterbo

Fatigue is a major contributor to haul-truck incidents in mining, with up to 65% of fatigue-related events associated with operator drowsiness or microsleep episodes, Williamson et al. (2011) and Caterpillar (2007). This study examines whether operator fatigue produces measurable and repeatable signatures in haul-truck telemetry. Eight confirmed fatigue-related disengagement events were analyzed using 20-minute telemetry windows centered around the incident. Statistical descriptors, Z-score normalization, first- and second-order derivatives, sliding-window variability, and cross-signal correlations were extracted from engine speed, throttle position, fuel rate, ground speed, and brake indicators. A logistic regression classifier was trained and evaluated using leave-one-event-out cross-validation. The model achieved a receiver operating characteristic (ROC) area under the curve (AUC) scores of 0.75–0.79, demonstrating consistent discriminative capability. A characteristic shutdown sequence characterized by sudden throttle collapse, fuel-rate decay, RPM reduction, and unbraked coasting was observed across all events, indicating operator disengagement rather than mechanical malfunction. Earlywarning indicators appeared 90–500 seconds before shutdown in the events analyzed, suggesting practical potential for real-time fatigue prediction. These findings provide initial evidence that telemetry-based fatigue detection is feasible and could enhance safety in mining operations.

Feb 22, 2026

By S. Chander, A. Briceno

The properties of surface films on pyrite have been studied through electrochemical techniques of cyclic voltammetry and AC impedance, measurements. The characteristics of the surface films depend on the conditions of oxidation and the source of pyrite. At potentials near 0.0 V, some pyrites have large values of polarization resistance, showing a certain degree of passivity. Some pyrites show more passivation than others, however. On oxidation, meta- stable phases of Fe(OH)2 and Fe(OH)3 form that transform to more stable phases on aging. The growth of surface films near the corrosion potential of pyrite follows a linear kinetics that is attributed to a chemical (or an electrochemical) reaction as the rate determining step. The surface film is considered to be a hydroxide or an oxide because it is hydrophilic. This study has also demonstrated that AC impedance ,measurements can be used to study the growth characteristics of films at mineral/solution interfaces.

Jan 1, 1988

By H. L. Bourne

Not everyone understands the concept of mineral royalty. Mineral royalty is a fee paid to a landowner by someone who extracts a mineral commodity from the owners property. The royalty contract between the lessor and lessee contains clauses and conditions that are significant to both parties, e.g., annual m1n1mum, escalation factor, duration of the lease, reclamation and assignability. Comparison of royalty rates requires knowledge of many conditions that influence the value of a given deposit. People in several different professions benefit from shared royalty information.

Jan 1, 1989

By J. Simmons, P. Ziemkiewicz

Acid-Base Accounting (ABA) is an analytical procedure that provides values to help assess the acid-producing and acid-neutralizing potential of overburden rocks prior to coal mining and other large-scale excavations. This procedure was developed by West Virginia University scientists during the 1960s. After the passage of laws requiring an assessment of surface mining on water quality, ABA became a preferred method to predict post-mining water quality,and permitting decisions for surface mines are largely based on thevalues determined by ABA. In order to predict the post-mining water quality, the amount of acid-producing rock is compared to the amount of acid-neutralizing rock, and a prediction of the water quality at the site (whether acid or alkaline) is obtained. We gathered geologic and geographic data for 56 mined sites in West Virginia, which allowed us to estimate total overburden amounts, and values for maximum potential acidity (MPA), neutralization potential (NP), net neutralization potential (NNP), and NP/MPA ratios for each site based on ABA. These values were correlated to post-mining water quality from springs or seeps on the mined property. Overburden mass was determined by three methods, with the method used by Pennsylvania researchers showing the most accurate results to actual overburden mass. A poor relationship existed between MPA and post-mining water quality, NP was intermediate, and NNP and the NP/MPA ratio showed the best prediction accuracy. In this study, NNP and the NP/MPA ratio gave identical water quality prediction results. Therefore using NP/MPA ratios, values were separated into categories: <1 should produce acid drainage, between 1 and 2 can produce either acid or alkaline water conditions, and >2 should produce alkaline water. On our 56 surface mined sites, NP/MPA ratios varied from 0.1 to 31, and six sites (11%) did not fit the expected pattern using this category approach. Two of eight sites with ratios <1 did not produce acid drainage as predicted (the drainage was neutral), and four of 40 sites with a ratio >2 produced acid drainage when they should not have. These latter four sites were either mined very slowly, had non-representative ABA data, received water from an adjacent underground mine, or had a surface mining practice that degraded the water. In general, an NP/MPA ratio of <1 produced acid or neutral drainage sites, between 1 and 2 produced mostly alkaline drainage sites, while NP/MPA ratios of >2 produced alkaline drainage with a few exceptions. ABA is a good tool to assess overburden quality before surface mining and to predict post-mining drainage quality after mining. The interpretation from ABA values was correct in 50 out of 52 cases (96%), excluding the four anomalous sites, which had acid water for reasons other than overburden quality.

Jan 1, 2003

By Raymond F. Mikesell

This paper evaluates the contributions of "third parties" to surplus capacity in the world metals industries in the 1980s. Special attention is given to the role of international development agencies, such as the World Bank, that have made project loans to state mining enterprises. The paper also reviews the contributions to surplus capacity of the International Monetary Fund and evaluates the large volume of credits from commercial banks to developing countries. Although the credits to Third World countries during the 1970s facilitated the expansion of mining capacity in those countries, no one source of financing can be held responsible for a significant portion of the expansion.

Jan 1, 1989

By Ann M. Hagni

One of the most costly factors in the production of aluminum is the consumption of energy in the form of electricity. Energy consumption is increased as refractories in the Hall-Heroult reduction cells are corroded by penetration of the fluxes cryolite (Na3AlF6) and villiaumite (NaF). To decrease thermal conductivity and refractory waste, protective barrier linings are installed. Dry powder barrier linings form stable reaction products at cell operating temperatures. Four dry powders composed of vermiculite, corundum, wollastonite, and anorthite are characterized mineralogically by X-ray diffraction, reflected light microscopy, scanning electron microscopy, and cathodoluminescence microscopy in this research project.

Jan 1, 1998

By Osvaldo Bascur, Laurent Garrigues, Nouna Kettaneh, Svante Wold

The chemical, oil, semiconductor, mining, and paper and pulp industries, as well as most other modern industries, are rapidly expanding the range of measurements used to characterize raw materials, process steps, intermediates, and final products. In addition, process variables such as temperature, pressure, and flow become more and more numerous, providing extra information on the state of the process. However, no matter how many sensors are added, the underlying sources of variations that drive the process behavior remain constant. On the other hand, the measuring frequency of these data has increased from once a day or once an hour to once, ten, or even hundred times a minute. This gives masses of data that are swelling in both directions (more variables and more observations). These data need to be properly stored, managed, and analyzed to provide diagnostics about the state of the process as well as an understanding of the relationships between different parts of the process and the product properties. Projection methods such as PCA (principal components analysis) and PLS (projection to latent structures) compress process data to informative summaries of the original variables. These can be shown on line, providing an efficient, graphically oriented suite of diagnostics regarding the "health" and performance of the process. The power of these methods is illustrated by two examples of industrial data in the mining industry.

Jan 1, 2000

By J. Reyher, R. Bratton, G. Luttrell, B. Li

"Flotation is regarded as the best available method of upgrading minerals and coal fines. However, its efficiency deteriorates rapidly with decreasing particle size. Further, ultrafine concentrates are difficult to be dewatered economically, forcing companies to discard part of the ultrafine materials to impoundments. To overcome these problems, a new method of separating and simultaneously dewatering ultrafine particles has been developed. Following extensive laboratory-scale test work, the process, known as hydrophobic-hydrophilic separation (HHS), has been tested successfully in continuous operations at proof-of-concept (POC)- and pilot-scale tests. The results show that the HHS process is capable of producing high quality clean coal with high recoveries and low moistures. INTRODUCTION Coal preparation plants are designed with up to four parallel processing circuits for treating coarse (> 12 mm), intermediate (12x1 mm) small (1x0.15 mm), and fine (<0.15 mm) particles. The plus 0.15 mm fractions can be effectively cleaned efficiently with gravity separation methods (Wills, 2006). At present, the only commercially viable option for cleaning the finest fraction is froth flotation (Yoon et al., 1999). In flotation, air is dispersed in the form of small air bubbles in a tank in which coal fines are suspended. The small air bubbles selectively collect the hydrophobic coal particles and float to the surface, forming a froth phase which overflows into a launder. As is well known, ultrafine coal particles of less than 30-50 µm are difficult to be collected by the air bubbles, resulting in low recoveries. Furthermore, fine particle flotation suffers from low carrying capacities and poor selectivity due to entrainment problems. (Bethell et al., 2005; Luttrell et al., 2014). In addition, the froth products containing ultrafine coal are difficult to dewater. Mechanical dewatering in general becomes inefficient with decreasing particle size due to small cake porosity and high surface area, resulting in high moistures (Hucko et al., 1988). The cost often becomes prohibitive with particles of smaller than ~45 µm (Bethell et al., 2005). Moreover, the high-moisture products are difficult to handle and incur high shipping costs and lower thermal efficiencies (Honaker et al., 2013)"

Jan 1, 2016

By Paul C. Miclea

With the growing urban population and the concern for traffic congestion and pollution (emissions control), public transportation is becoming more and more attractive to both city dwellers and managers. To gain access to the central area of the city, the sub- way remains the most viable alternative, despite its higher cost when compared to above ground or elevated transportation systems. There are relatively few regulations and criteria for subway ventilation, particularly when compared with mine ventilation. The main document that provides guidance and general recommendations for subway ventilation and environmental control is the Sub- way Environmental Design Handbook, published in 1976 (2nd edition) by the U.S. Department of Transportation, Office of Re- search and Development. Many of the subway systems in existence today have been designed and built with ventilation features adequate for normal train operation, but their design does not consider stringent criteria for such emergency conditions as a train fire in a tunnel. The National Fire Protection Association&apos;s Standard for Fixed Guideway Transit Systems known as NFPA 130 as well as the ASHRAE Handbook - HVAC Applications (1995) provide specific design and operation requirements for subway ventilation systems. Some of the existing, old subways are upgrading their ventilation systems to comply with the new regulations. The ability of a particular ventilation system design to provide adequate ventilation during normal and emergency conditions can be evaluated using computer modeling and simulation techniques. A train fire will cause a sudden change in the tunnel ventilation pattern by adding an unsteady and fast-growing source of heat. The hot air and gasses created by a fire will tend to flow uphill, possibly against the normal flow, producing a &apos;backlayering effect." To prevent this effect from happening, enough ventilation must be provided and the governing criterion to establish the required airflow is called &apos;Critical Velocity." Several software packages are available for special applications on tunnel and station ventilation as well as to model the spread of smoke and heat in case of a major tunnel fire, using Computational Fluid Dynamics. This paper presents the current issues in subway ventilation, as shared by the public transit community around the world, together with modern alternative design concepts vis-à-vis the more stringent emerging Fire-Life Safety criteria. Examples of recent studies and ventilation systems design are provided.

Jan 1, 1997

By G. W. Luxbacher

Coal mine infrastructure is rarely designed solely on the basis of ventilating the underground workings. Instead the optimization of a mining sequence, the minimization of coal quality variation, reduction of coal losses by adapting to property boundaries and geologic structure (seam inclination, roof conditions, coal thickness, etc.) or other similar considerations have formed the objective for mine plant design and layout. Infrastructure development may also reflect a desire to maximize production early in the life of the mine or to permit flexibility in mining according to market conditions. Requirements for coal mine ventilation, established by the 1969 Coal Mine Health and Safety Act, have mandated changes in the traditional concepts of mine plant design in the United States. Mines, in operation prior to the passage of the Act have experienced severe limitations when attempting to adapt the existing mine infrastructure to meet the requirements of the law. In addition the increased quantities of air required, velocity limitations on trolley haulage and belt lines, the establishment of separate intake escapeways and gob area ventilation have com- pounded the inherent complexity in planning mine ventilation systems. Past practices in mine ventilation planning and design are no longer adequate. Given the complexity of today&apos;s ventilation systems, effective planning and design approaches are required. As such, the interrelationship between the overall coal mine plant design and ventilation system design is examined. An approach to ventilation system design constrained by global considerations of mine plant design, is presented. The proposed approach is, however, applicable to the design of new mine ventilation systems as well as to the modification of existing systems.

Jan 1, 1980

By J. Y. Hwang, M. L. Jeong, R. C. Greenlund

Various aluminum-smelting by-products from three production sources were received and characterized. The waste materials were tested for compound identification and environmental acceptance. A coarse metallic aluminum recovery test using an Eddy Current separator (ECS) was performed using two different Circuit configurations. White dross performed equally well with either Circuit, while black dross processing shows significant difference on the separation results. It was found that ECS technology was effective for particle sizes down to 6-10 mesh.

Jan 1, 2001