Search Documents

By Alwyn Protheroe, Steve Smith, Herbert Jr. Gibson

In September of 2000, Cowin and Company, Inc., contracted with Paramont Coal Corporation to construct a large decline approximately 820 m (2,700 feet) in overall length at a grade of 8 degrees to the Lower Banner Coal Seam. This paper will discuss the methods used by the contractor and owner to overcome the unique problems required to construct this tunnel in a coal mine environment. The problems include, initial design considerations, equipment selection, ventilation, ground control, control of water in?ows, and placement of concrete.

Jan 1, 2003

By Robert L. Gamble

The world's largest fluidized bed steam generator located at Rivesville, West Virginia is currently undergoing initial operation. This unit is designed to generate 3708 kg/s (300,000 Ib/hr) equivalent to 30 MWe of superheated steam while firing coal in a fluidized bed of limestone. Coal was first fired in this unit in December, 1976 and start up operation is progressing.

Jan 1, 1977

By E. D. Thompson, Y. J. Zhang, K. F. Unrug

This paper presents the results of a recent study on the development of an in situ testing method for determining coal strength in mine pillars. The strength testing is performed in the horizontal holes drilled into the coal rib using a penetrometer, which is an hydraulically powered device that uses an indenter to press on the surface of the borehole until the load reaches the failure point of the coal. The pressure and the penetration of the loading pin are recorded by a data-acquisition unit. The results collected from several coal mines indicate that this testing method is ideally suited for the realistic coal strength measurements. The new testing system not only improves the accuracy of the pillar-strength determination, but it is more cost efficient than the conventional method.

Jan 1, 1997

By A. P. Cook

Methane Rating has been developed from a need, in South Africa, for quick and simple measurement of coal face methane characteristics. It employs proven existing direct measurement methods, adapted specifically for rapidly advancing coal face conditions, to deal with the short term high release rates encountered during continuous miner coal cutting. The Rating is a comparative value, relative to the normal or average conditions encountered within a maintained data base. The seam gas content and the initial emission rate are plotted against each other on a graph, where they are compared with the average conditions to obtain the rating. The higher the seam gas content, and the higher the initial methane release rate, then the higher the Methane Rating, on a scale of 1 to 4. Methane being released from a newly mined coal sample is measured once underground, from a sealed gas-tight canister. The sample is returned, still sealed, to surface and milled to rapidly release the remaining methane. It is later intended that the milling process is also completed underground. Applications include the identification of changing methane conditions, outburst prone conditions, methane emission against advance, and mining in devolatilised coal.

Jan 1, 1998

By Jon C. Yingling

A control system for reducing peak loads on mine conveyor networks is proposed. The system involves continuous monitoring of flows into the conveyor network and section feeders with variable discharge capability. The control strategy uses differences in material transit times from various production units to the transfer points in the network to forecast load levels that will be intersected by the discharge of the controlled feeders over future time intervals. Feeder setpoint adjustments are made to prevent excessive peaks in the combined flows at the transfer points, while maintaining adequate feeder throughflow to avoid production bottlenecks.

Jan 1, 1992

By F. C. Turin, T. L. Friend, A. G. Mayton, J. S. Jaspal, W. J. Wiehagen

This paper describes the serious injuries that have occurred to bulldozer operators working at domestic coal, metal and nonmetal mines in the United States. A serious injury is defined as one that results in either a fatality or in lost work time. Examined were 873 injury records compiled by the Mine Safety and Health Administration (MSHA). The time period covered was 1988 through 1997. These injuries resulted in 18 fatalities and 31,866 lost work days. All of these injuries occurred to dozer operators while they were performing common production tasks. An injury classification system was developed to code the narrative information that describes the circumstances surrounding the injuries. Jolts and jars accounted, for 604 or 70% of the serious injuries to bulldozer operators, and jolts and jars accounted for 75% of the workdays lost. Vertical jars comprised the largest set (354 incidents) of jolting and jarring injuries. In more than half of these incidents, the operator was backing up the dozer. Working near an edge carries significant risk for fatal injuries. Of 116 incidents where the dozer fell over an edge, rolled over or fell into a hidden void, 14 (12%) resulted in fatal injuries. In cases where the dozer operator either jumped or was thrown out of the cab in a fallover or rollover, seven out of 17 of the operators were killed. This study finds that further reductions in injury risk would require more widespread use of seat belts; consideration (and maintenance) of the seat and seat suspension systems that might reduce injury risk from jolts and jars; research interventions to assess the effect of alternative engineering designs to dampen or isolate the effects of shock and vibration; and continued attention to skilled performance, i.e., the integration of hazard awareness, recognition and response with dozer operational skills.

Jan 1, 2003

By Abdullah Arik

Verification of computer generated reserve models is essential since the computer does not automatically check the validity of methods and assumptions selected by the user and their results. For the computer to do model verification would require an expert system which would perform tests on the model and determine if the model is valid. Since such an expert system is not available, it is up to users to verify the models they develop.

Jan 1, 1995

By M. M. Botz, F. W. DeVries

Discussion by F.W. DeVries Comments on natural cyanide attenuation. The paper by Botz and Mudder in the November 2000 issue of Minerals and Metallurgical Processing had one disappointing aspect. Table 1 (p. 229) failed to include a significant species - neutral copper cyanide (CuCN). This compound has been most trouble-some in many plant-scale cyanide cleanup processes, includ- ing acidification-volatilization- reneutralization (AVR), hy- drogen peroxide cleanup and air/SO2 cleanup. It has also plagued many pilot efforts to use ion-exchange (IX) resin technology. This author elucidated the concept that, under some conditions, copper cyanide failed to precipitate out of treated effluents and appeared to exist as a filterable colloid that reported as copper and cyanide, with the latter measured as WAD (weak-acid-dissociable) cyanide in that analytical method. The concentrations measured were very near the levels of 0.2 ppm, often the regulatory limit for WAD cyanide. The copper concentration, using the 1 : 1 ratio for this com- pound, would then be more than 0.4 ppm, which could also be unacceptable. We discovered that it was unsafe to assume that the Cu(CN),- would surrender both cyanide ions simultaneously and allow cupric copper to be removed subsequently as, say, cupric ferrocyanide (Hatchett's Brown). This compound could be ignored as safely as the "iron blues," as essentially an inert solid, stable in geologic time if not exposed to sunlight. Under poorly controlled oxidation of the cyanocuprite ions (copper with four, three or two cyanides complexed to the copper), CuCN could well be formed and could not be assumed to precipitate out as a solid. The authors of the paper, by failing to include the CuCN species in their model, may have left users of the model prone to ignore the possible occurrence of the colloidal(?) form in the discharge, thus finding an effluent that failed to meet regulatory limits. (See addendum below.) This somewhat ephemeral material may well have been responsible for some large-scale failures of cyanide destruction technology to succeed at sites in North America and elsewhere. Two specific references alluding to this occurrence may be found: Griffiths et al., 1987, "The detoxification of gold-mill tailings with hydrogen peroxide," Journal of the South African Institute of Mining and Metallurgy, September, p. 282. DeVries, 1989, "Improved understanding in detoxification of cyanide leach liquors using peroxide" Rand01 Gold Conference, Sacramento CA, p. 15 1. It is advisable for workers in this area of cyanide removal or recycle to avoid assuming that CuCN will, with certainty, precipitate out of solution, or that the dicyanocuprite ion will part simultaneously with both cyanide ions and allow cupric copper to be dealt with by other reactions. One further piece of work may be incomplete. That is, a definitive study of the long-term behavior of CuCN that does precipitate when exposed to other compounds present in neutralized tailings. Addendum. The extremely complex reaction of cupric ion on cyanide- which, of course, results in oxidation of cyanide to cyanate, probably through the intermediate stage of forming cyanogen [(CN)2] from oxidation of HCN with its hydrolysis to cyanate and cyanide ion - involves two cyanide moieties and the reduction of the cupric ion back again to the cuprous state. This, then, can form the CuCN potential "solid" that was already the undesirable species. In cyanide cleanup, with either air/SO2 or hydrogen peroxide, copper is generally employed as the catalyst, so it is unclear what happens when the CU(CN)2-1 is ultimately exhausted. Certainly, the field evidence is quite clear that all

Jan 1, 2002

By Kailash Narayan

Atlantic Richfield Company began operating a commercial uranium solution mining project in April, 1975 in Live Oak County, 10 miles southwest of the town of George West (Figure 1). The operation is designed to produce 250,000 pounds of U303 per year and is jointly owned by Atlantic Richfield Company, Dalco and U. S. Steel. The proprietary process employed in this operation consists of injecting an alkaline leaching solution into the ore-bearing formation through a pattern of injection wells. The uranium-bearing solution is then removed through producing wells using submersible pumps in central production wells. The produced solution is pumped through a pipeline to the plant area where the uranium is extracted. The barren solution is refurbished and returned to the pattern area for reinjection. The injection field and plant site are located in the drainage of Spring Creek, a small intermittent stream tributary to the Nueces River. Land use in the area is primarily agricultural -- cattle ranching and farming -- but several producing gas fields are present in the areas as well.

Jan 1, 1976

By H. Sevim

Three transportation systems in surface coal mines: 1-Truck Haulage, 2-Belt Conveying, and 3-Coarse-Coal Slurry Transportation are compared from the operations and cost point of Views. Computerized design and cost models were developed and cost data banks were compiled for each system. These models can be used to evaluate transportation systems and layouts that are practiced in most of the U.S. surface coal mines. A typical midwestern area strip mine was considered for illustration purposes. Sensitivity analysis on critical parameters such as production rate, transportation, distance, etc. was conducted and the outcomes are presented.

Jan 1, 1990

By Robert C. Bates

Published information on costs of radon-daughter control in uranium mines was analyzed to develop estimates of the cost per ton for any level of radiation exposure control. All data were converted to 1967 cost of living index to provide a common analysis base. Results of the analysis show that the cost per ton increases exponentially as the radiation level is lowered. A linear relationship with the cost of living index is assumed, and equations and graphs are provided to estimate control cost per ton for any exposure control level and cost of living index.

Jan 1, 1981

By Roberto Pimentel de Souza

CURD started producing pellets in 1969, with one two-million ton straight grate plant. In the beginning of April '73, the second unit came on stream with an additional capacity of 3 million TPY of pellets. In January '77, the third unit started, bringing the annual capacity to 8 million TPY. For the present year 3 more units, 3 million each, are expected to begin production. CVRD's experience is given about the use of different binders and additives. Over the years several kinds of pellets have been produced to satisfy the market requirements. General quality information is given regarding each.

Jan 1, 1978

By M. Polat, G. Ahuja, S. Chander, M. S. Klima

A study was conducted to investigate the use of flotation in combination with dense-medium cycloning utilizing ultrafine (-10 um) magnetite, as an integrated process for high-efficiency cleaning of fine coal. The objective was to produce a high-quality (low-ash, low-sulfur) coal, while reducing the amount of non-magnetic material that would need to be removed by magnetic separation. Three dense-medium cyclone tests were performed using different underflow diameters to produce feed material for the flotation separations The use of different underflow configurations caused a variation in the pulp and solids splits, which changed the clean-coal yield and the magnetite-to-coal ratio of the cyclone products, and hence, the composition of the flotation feed. Flotation was used to separate the clean coal and to recover the magnetite contained in the cyclone overflow stream. Any ultrafine refuse material, which may have reported to the cyclone overflow stream, was also removed in this step, further upgrading the product. In addition, flotation was used to improve the overall yield by recovering a middlings fraction from the cyclone underflow stream. It was found that flotation was very effective in separating the coal (or middlings) from the ultrafine magnetite, even under variable feed conditions. Magnetite recoveries approaching 99% were possible using rougher-cleaner separations in a laboratory flotation cell. This paper presents the results from this study.

Jan 1, 1995

By T. V. Vasudevan, J. Blaakmeer

Adsorption experiments were conducted at two different solid loadings to investigate the mechanism of oleate adsorption on apatite. Adsorption density at pH 10 was found to be dependent on solids loading in an oleate concentration region where surface precipitation could occur. Analysis of adsorption isotherms indicated three distinct regions of adsorption. In region I (below the region of calcium oleate precipitation), molecular adsorption was observed. Simultaneous molecular adsorption and surface precipitation occurred in region 11, while surface precipitation was predominant in region I11 along with some bulk precipitation. Correlation between flotation of apatite with sodium oleate and the mode of oleate interaction with the surface is established.

Jan 1, 1988

By Kirk H. P. E. McDaniel, Mark T. Strever, Keith G. Jr. Wallace

This paper presents the design and installation of an underground ventilation remote monitoring and control system at the Waste Isolation Pilot Plant. This facility is designed to demonstrate safe underground disposal of U.S. defense generated transuranic nuclear waste. To improve the operability of the ventilation system, an underground remote monitoring and control system was designed and installed. The system consists of 15 air velocity sensors and 8 differential pressure sensors strategically located throughout the underground facility providing real-time data regarding the status of the ventilation system. In addition, a control system was installed on the main underground air regulators. The regulator control system gives indication of the regulator position and can be controlled either locally or remotely. The sensor output is displayed locally and at a central surface location through the site-wide Central Monitoring System (CMS). The CMS operator can review all sensor data and can remotely operate the main underground regulators. Furthermore, the Virtual Address Extension (VAX) network allows the ventilation engineer to retrieve real-time ventilation data on his personal computer located in his workstation. This paper describes the types of sensors selected, the installation of the instrumentation, and the initial operation of the remote monitoring system.

Jan 1, 1995

By A. H. Baldo

Covers a very broad spectrum of problems and solutions. The problems are multitudinous and their solutions are sometimes simplistic, sometimes ingenious and sometimes within a very broad interpretation of the law. However, one thing is quite certain: the problems and their solutions will have a direct impact upon corporate and personal well being. First of all, why does one mine in a foreign land? Since the Bronze Age, when ancient man discovered the metallurgy of copper, tin and zinc, intrepid souls have been wandering afield searching for and exploiting those mineral deposits which would create wealth and security for his city-state or community.

Jan 1, 1981

By Yi Luo

A massive roof fall occurred in a small room-and-pillar coal mine. The roof falls occurred under a barrier pillar in a closed coal mine located a short distance above the active mine. The extensive fractures connected the active mine with the old mine, turning them into a “combined mine.” Since completely sealing off the roof fall area is prohibitively expensive for the mine, ventilating the connected old mine became the only option. A comprehensive investigation was conducted to understand the atmospheric condition in the old mine and to find an efficient way to ventilate the “combined mine.” A set of studies involving geology, gas content, pillar stability and mine subsidence were performed to explore whether the closed mine is filled with an explosive air-methane mixture. The air quantity measurement data were used to determine the resistance of the air path formed through the fractured zone. Observations and measurements made from a tour to the underground and mine surface enabled the formulation of simple but effective ways to ventilate the old mine. The ventilation network analysis also suggested methods of control, so that sufficient ventilation air can be directed to the two parts of the old mine.

Jan 1, 2010

By M. E. Orman

Many factors must be considered when designing a heap leach pad. Geotechnical properties of the ore, can and will affect how well an ore leaches, the solution recovery, stability of the heap, and settlement. As a heap is stacked some of these properties will change due to the increased load. In order to properly design a heap these properties should be determined beforehand so that the heap performs as intended.

Jan 1, 1997

By G. Q. Huang, Q. X. Yun, Z. Y. Gui

This paper provides a new approach to deal with control of ore-rock excavation by means of the optimal control theory-an important branch in cybernetics. In the optimal control theory, the elementary functions are state-transition function and objective function. According to the characteristics of mining planning and production, a set of formulation are established to cope with ore- rock excavation. The formulations include basic formula, anti-disturbance formula as well as other special formula. The new approach has been successfully used in several mines of China.

Jan 1, 1996

By P. A. Korpi

The angular spiral lining system reduces energy consumption and grinding media consumption in grate discharge ball mills. This paper discusses the effect of this lining system on mill product size distribution. Performance comparisons of a grinding circuit outfitted with angular spiral liners in the ball mills are made with respect to standard double-wave liner installations. The angular spiral lining system was developed by Waagner-Biro of Austria. The installation of this lining system at Magma Copper Company, San Manuel, Arizona, is the first of its kind in a grate discharge ball mill used for wet grinding.

Jan 1, 1979