Search Documents

By S. Norman Kesten

The Resource Conservation and Recovery Act, commonly known as RCRA, which amends the previous Solid Waste Disposal Act, was signed into law on October 21, 1976. Members of the mining industry began their contacts with EPA in this area two to three years before the Act finally was passed, and that seemed and probably was all to the good. We reviewed and commented upon their studies and in general tried to acquaint them with the peculiarities and the uniqueness of the wastes generated by our industry, of which they were abyssmally ignorant. I suppose we thought that through the bureaucracy we might have some influence upon the provisions of the solid waste legislation that was being bandied about on the hill. Certainly the industry, in general, did very little direct lobbying, as I recall, and there were several reasons for that. For one thing we conceived that the legislation was aimed at the chemical industy and believed that if their people looked after their interests, ours would be safeguarded automatically. Also, the Federal Land Policy and Management Act (FLPMA) was heating up at the same time and, in fact, was signed into law on the same day. In addition, a great deal of lobbying activity was required by amendments of the Clean Air Act and Federal Water Pollution Control Act that were being put together in Congress. These were conceived to be of far greater importance to our industry than a bill to control mostly chemical wastes and, in fact, new bills in both areas became law the following year. Finally, the solid waste bill, RCRA, was patched together by committee staffs over one weekend and was reported out by a conference committee rather hurriedly. Some little goodies about mining were almost after-thoughts in this process.

Jan 1, 1981

By E. Steel, V. S. Znamensky, A. Wylie

The asbestiform habit is most commonly developed in certain amphiboles and chrysotile, but other minerals also may crystallize with this unusual habit. The habit may be characterized by (1) a fibril structure, single or twinned crystals of very small widths (generally less than 0.5 pm), which have grown with a common fiber axis direction, but are disoriented in the other crystallographic directions; (2) anomalous optical properties, primarily parallel extinction; (3) unusual tensile strength; (4) high aspect ratio; and (51 flexibility. In addition, there is evidence to indicate that some amphibole asbestos may have unusual surface properties. ASBESTOS AND THE ASBESTIFORM HABIT Asbestos is defined as a group of highly fibrous silicate minerals that readily separate into long, thin, strong fibers of sufficient flexibility to be woven, are heat resistant and chemically inert, and possess a high electric insulation, and therefore are suitable for uses where in- combustible, nonconducting, or chemically resistant material is required (Gary, et al., 1974). The most common minerals that may occur with the asbestiform habit are chrysotile, grunerite (amosite], riebeckite (crocidolite), actinolite, anthophyllite, and tremolite; although the development of this habit among these minerals is rare. Other minerals, most notably other amphiboles, can occur in this habit, but no others have been mined commercially as asbestos. All asbestos is confined to metamorphic rocks, even though other habits of the amphiboles are common in igneous rocks. Slip fiber veins are the most common deposits (South African amosite, Canadian chrysotile, etc.), but mass fiber deposits also may occur such as California chrysotile or mountain leather. Field relations and experimental data support the hypothesis that metasomatism is the dominant process in the formation of asbestos fibers, amphibole as well as serpentine. The crystal habit of a mineral is the shape or form a crystal or aggregate of crystals take on during crystallization. The asbestiform habit has a number of characteristics that differentiate it from other habits. Chief among these is the fibril structure.Afibri1 is a single or twinned crystal with a very small width, generally less than 0.5 pm, and an extremely high aspect ratio; bundles of fibrils may have lengths reaching into the cm. Fibrils share a common crystal growth direction along the long axis of the fiber, but appear to be disoriented with respect to one another in the other crystallographic directions. The structure of the individual fibrils, and the organization of fibrils within a fiber may differ among the various types of asbestos. The fibril structure of asbestos is probably a factor in controlling a number of secondary properties that include high tensile strength, flexibility sufficient for weaving, and anomalous optical properties. The high tensile strength of asbestos is quite remarkable, exceeding that of the ordinary varieties by a thousand fold (Zoltai, 1978). In part, this may be attributed to the lack of defect on the fibril surfaces (Zoltai, 19781, but some contribution also must come from the existance of bundles and the nature of the ordering of and forces among the fibrils. The flexibility is not only enhanced by the fact that the fibrils may slip past one another, but by their small widths and extreme aspect ratios. However, structural defects parallel to the fiber axis also may contribute to this property. Among the common commercial asbestos types, the greatest flexibility is found in chrysotile and the least in grunerite asbestos (amosite), varying inversely with fibril thick- ness. In addition, at least for chrysotile, composition also may affect the flexibility of the fibers. Finally, most asbestos minerals are mono- clinic, but optically display parallel extinction (Heinrich, 1965, and Wylie, 1978). This also must be due, in part, to the ordering or lack of ordering of the fibrils. The fibril structure is probably a random

Jan 1, 1986

By Fathi Habashi

Precipitation of a metal from an aqueous solution of its salts by another metal is known as cementation, because the precipitated metal is usually cemented on the added metal. This phenomena was once described by the alchemists as "transmutation," when they dipped a piece of iron in a solution of copper sulfate and the iron was coated with a layer of metallic copper. The process can be predicted in terms of electrode potentials. The metal with the more positive (oxidation) potential, as given in Table 13-1 of the electromotive series, will pass into solution and displace a metal with a less positive potential.

Jan 1, 1970

By Cao Changlin, Gong Qian, Hu Jiexue

The thiosulfate, effects copper of concentrations of and ammonia ou the extractlon of gold from sulfide gold concentrate have been studied. The experimental results showed that it is possible to reduce thiosulfate concentration. Above 95% of gold extraction was obtained in O. 2M thiosulfate leaching solution in two hours under the suitable conditions. Therefore, the process of washing residue was simplified, the consumption of thiosulfate and the loss of thiosulfate carried were reduced. by washing residued.

Jan 1, 1992

By Malcolm J. McPherson

Mine shafts that are used as primary ventilation routes are different in their airflow characteristics to other subsurface openings because of the aerodynamic effects of guide rails, buntons, pipes, cables, ropes, and shape, size and velocity of conveyances. As many shafts contribute heavily to the overall resistance of a mine ventilation circuit, it is important to be able to predict the resistance of a planned shaft with reasonable accuracy. This paper describes part of a study on the ventilation characteristics of hoisting shafts, conducted for the Basalt (Nuclear) Waste Isolation Program (BWIP). Methods of quantifying each of the four components of shaft resistance are developed; namely the shaft walls, fittings (buntons, pipes, etc.), the skips or conveyances, including the dynamic effects of their motion, and shaft stations. Practical guidance is given on ways of reducing the shaft resistance. The paper concludes by giving a step by step procedure for the ventilation aspects involved in the design of combined hoisting/ventilation shafts.

Jan 1, 1987

By Dennis Ofiara, Paul Zick

Two 8.2 m diameter flood control tunnels are being constructed in the Taylor Shale Formation beneath San Antonio, Texas. These tunnels use precast concrete segments as final lining. This paper describes the features of the segments chosen for this project. The tunnels are being excavated with a hybrid Tunnel Boring Machine. This paper also describes the features of the TBM which make the machine compatible to the type of segments chosen.

Jan 1, 1989

By A. W. Deurbrouck, W. W. Agey

Introduction The modern wet concentrating table is a rectangular or rhomboid shaped normally rimed-deck operated in essentially a horizontal plane (Fig. 23). A drive mechanism imparts a differential motion to the deck along its long axis while water flows by gravity along the short axis. Tables are currently employed for processing large tonnages of coal and lesser tonnages of barite, beach sands, chrome, glass sand, garnet, iron, manganese, mica, phosphate, potash, tantalum, tin, tita-

Jan 1, 1985

In a world dependent in part on the consumption of depletable natural resources, development of new areas of mineralization is a necessity for replacing those reserves. Exploration, which is the initial task of replacement, is an information-gathering process which supplies input for management decisions on mine development. If the demand for resources is the driving force of exploration, then the scientific basis for its pursuance is the hypothesis of anomalous mineralization in a metallogenic province, which is tested by measuring physical characteristics of natural phenomenon. The resulting data are reduced, analyzed, and interpreted to locate expressions or responses associated with possible ore bodies. The process is, in fact, repeated in ever increasing measurement detail to increase the accuracy and precision of information for decision making. Exploration ceases when management makes the decision to develop a mineralized area, to hold a property for more favorable market conditions, or to drop a property because it is not economically viable.

Jan 1, 1979

By Patricio Zarate

Due to the intrinsic variability in orebodies, similar metallurgical behaviour of all material sent to the concentrator is expected to have some variability. Still some specific ores have anomalous performance which can severely impact on the concentrator’s production of metal, in this case copper. The study first will show the mineralogical characteristics of “usual ore” and of this specific “abnormal ore” which will have to be processed by the concentrator in the future. After that base conditions on both ores and flotation test procedure will be explained. Later the different alternatives tested regarding collectors and modifiers results will be compared. Finally, after discussing the different results with different reagents and considering operational variables of the concentrator, Floticor PD 702 is recommended to obtain the best copper recovery without increase in excess mass recovery.

Feb 1, 2025

By S. Rezaei

Moving ground in the mining industry is almost inevitable; however comprehensive awareness of these movements is necessary to mitigate risk. Monitoring of displacements caused by mining is a key tool for geomechanical risk management. Good monitoring may prevent unexpected failures and protect personnel and equipment. Many displacement monitoring techniques are available, however not all are reliable, accurate, and cost effective. Close range photogrammetry (CRP) is a monitoring method with high accuracy, reliability, and cost effectiveness; and has the ability to measure places that are inaccessible. In CRP, some series of photos are taken in different positions with different angles at different time intervals depending on the displacement rates. These photos are processed using PhotoModeler software and 3D models are made. By comparing 3D models, displacements can be measured. This method has been demonstrated at the Freeport-McMoRan Safford Mine in Arizona. A fault related instability in part of the pit is reactive to mining, and provided an opportunity to compare results between traditional monitoring methods and CRP. In this project, multiple series of photos were taken at different times using a Canon 5D Mark III digital camera, then PhotoModeler software used to make 3D models for each specific measurement event. Movement rates were determined by comparing different 3D models. These results are then compared to results of other monitoring methods to validate the CRP displacement method.

Feb 27, 2013

By M. Polat, S. Chander

Many models have been suggested in the past to obtain a satisfactory fit to flotation data. Of these, first-order kinetics models with a distribution of flotation rate constants are most common. A serious limitation of these models is that type of the distribution must be pre-supposed. Methods to overcome this limitation are discussed and a procedure is suggested for estimating the 'actual' distribution of flotation rate constants. It is demonstrated that the classical first-order model fits the data well when applied to coal flotation in narrow size-specific gravity intervals. When applied to material which is fractionated on the basis of size alone, the use of three parameter models, which were modified from their two parameter analogs such as rectangular, sinusoidal, and triangular, gave most reliable results.

Jan 1, 1995

By J. Frostiak

The Campbell gold operation of Placer Dome Inc. produces an arsenopyrite-sulphide concentrate which must be treated either by roasting, biooxidation or by pressure oxidation to obtain high gold recoveries. Pressure oxidation is a proven process and has the inherent advantage of meeting the stringent environmental regulations in the province of Ontario. A comparison of biooxidation and pressure oxidation was completed early in 1990 and the latter was selected by Placer Dome as the preferred process for replacement of the roasters. The commercial plant design was based on technology supplied by Sherritt Gordon and in July of 1991, the existing roaster operation was shut down and a new pressure oxidation plant was commissioned. The following summary describes the start up of the new facility and presents typical operating data.

Jan 1, 1992

By Donald E. Hulse

Selection of a block size for a computerized 3 dimensional ore body model is an exercise in compromises. Larger blocks decrease the use of computer resources and decrease the variance of the block estimates. Smaller blocks increase the resolution of the model and the selectivity which can be used in the planning, but increase the variance of estimates in the individual blocks. A common rule is that blocks can be as small as one fourth the average sample spacing, however this ignores the interrelationship between the block size, the sample spacing, and the variogram model. This paper will explore this relationship Kriging estimation variance will be used as a comparative measure of estimate quality. Graphical techniques will be used to show that there is a point where smaller block sizes cease to contribute to the resolution of the model. A method of evaluating the consequences of block size decisions will be examined.

Jan 1, 1992

By N. W. Johnson

The behavior of non-sulphide gangue in chaloopyrite flotation circuits has been investigated. Plant and laboratory tests were carried out on five different ores, and linear relationships were found to exist between the rates of recovery of water and free nonsulphide gangue in the concentrates although there was evidence from pilot plant tests that these were linear approximations to parabolic curves over the limited regions which were observed. There was evidence that the free non-sulphide gangue enters the concentrate by hydraulic classification and a classification function has been proposed to define this behavior. This function is suitable for inclusion in a mathematical model of the process.

Jan 1, 1972

By D. R. Schmitt, B. L. Jensen, T. J. Ahrens, C. L. Smither

The in situ elastic moduli of rock are measured holographically by a borehole instrument in marble and oil shale. A point force induced displacement field is recorded with double expo- sure holography. Data consists of a fringe pat- tern on the viewed hologram. The elastic moduli are determined by modelling of the fringe pattern. Only Young's inodulus is fairly constrained by the present data reduction. For an applied force of 520 [ ] 50 Newtons, a marble was found to have a Young's modulus of 56 [ ] 8 GPa, near an ultrasonically determined value of 48 [ ] 6 GPa. In an oil shale, an applied force of [ ]

Jan 1, 1986

By James A. Brierley

The author has known Professor Wadsworth since the 1960s, when interest in the application of microbial technology for metallurgical processes was beginning its rapid rise. The development of bioleaching and mineral biooxidation was advanced, in part, by Wadsworth's belief in the potential for its application, as well as by his numerous contributions to the understanding of the fundamentals of hydro-metallurgy. Wadsworth is recognized for fostering research and development of the field and adding credibility to microbiological-based metallurgical processes, now often referred to as biohydrometallurgy. This Wadsworth Award is recognition of the field of biohy-drometallurgy. It is an honor to serve as a representative for all those individuals involved in research and commercial development of this technology. Modern commercial application of biohydromctallurgy began with the bioleaching of copper from submarginal-grade. run-of-mine material. Kennecott Copper successfully developed this process in the 1950s at the Bingham Canyon Mine in Utah. Other mining operations around the world followed Kennecott's lead. Today, dump bioleaching remains a very low-cost process for scavenging copper from rock that cannot be economically processed by any other method. Despite the commercial success of dump bioleaching, little effort has been made to enhance the micro Biological component of this leach process. Expansion of biohydro metallurgy into recovery of other metals did not occur until the mid-1980s, when the first commercial plant for the pretreatment of refractory gold-bearing concentrate was commissioned at the Fairview operation in south Africa. Now, processes for copper bioleaching and refractory gold pretreatment are engineered specifically to promote the activity of the microorganisms. This paper reviews the current state of commercial applications of biohydrometallurgy. It examines potential future developments and portrays the role of the microbiologist in facilitating continued growth and commercial acceptance of the technology. The commercia1 examples in this paper illustrate the expansion of microbial processing in the mining industry during the last 20 years. Copper bioleaching Early commercial applications of bioleach technology involved processing submarginal-grade, copper- bearing, run-of- mine rock in dumps. Recent applications of the technology use engineered bioleach heaps. Currently. all of these operations are in the Southern Hemi-

Jan 1, 2000

By Charles W. Rountree

Industrial Engineering in the industrial world is a relatively new field, having been conceived about the turn' of the century by Frederick W. Taylor, who was not satisfied with the hit-or-miss methods of evaluation and estimation. Through crude Industrial Engineering techniques never before used, he completely changed the bricklaying industry so that work accomplished was more than doubled. To help us better understand what we mean by Industrial Engineering, I think a very simple definition Is in order. Industrial Engineering is a scientific approach to problems in cost, production and operations: and is designed to provide a means of increasing producitivity and reducing costs through standards measurement and standardization of the best methods, practices and equipment, There are many complicated definitions, but pure and simply, it all boils down to providing the means for increasing productivity and reducing the cost. Industrial Engineering has been applied in manufacturing since Frederick W. Taylor?s time and in the last 20 years has grown in stature by leaps and bounds. It is a basic function of successful manufacturing companies and is an accepted fool firmly entrenched in manufacturing organizations. You may know of some successful manufacturing companies that do not employ Industrial Engineers as such, but someone in that organization is doing Industrial Engineering work. They have standards and controls whether they call it Industrial Engineering or not. The manufacturing industry has benefited from this tool; other wise, it would have been discontinued long ago.

Jan 1, 1958

By D. R. Zuchelli

The purpose of wrapping ball mills with thermal/acoustic blankets is twofold: 1) to maintain the desired temperature inside the mill, and 2) to reduce the sound emanating from the mill. This field case study focuses solely on the latter, evaluating and documenting the sound level reduction attributed to the installation of the blankets on ball mills and its potential to reduce the noise dose experienced by the process attendant. One of the three ball mills had already been treated (baseline) before the evaluation started. However, treating the remaining two mills still proved to be very effective, further reducing ball mill noise in the near field by as much as 10.0 dBA and producing far field noise reductions of 3.0 dBA or greater, extending as far as 35 feet from the mills and to the floor above. The model developed from the survey data shows that a process attendant spending a substantial portion of a shift in the mill building will experience a significant reduction in overall noise dose.

Jan 1, 2010

By Harold E. Goetzman, Blair R. Benner

The U.S. iron ore industry is located primarily in Northern Minnesota and Michigan's Upper Peninsula with one additional small plant in Missouri. There are currently some 10 plants operating that produce about 48 million tons per year of pellets. The major reagent use occurs in the three general areas of: flocculation, flotation and pellet additives. Minor areas of usage are for corrosion inhibition and dust suppression. Current practice as to types of reagents, consumption, and method of application are reviewed. The interaction of reagents with other parts of the process are discussed. Also included is a discussion of future reagent needs.

Jan 1, 1994

By Fred N. Kissell, Jeffery L. Kohler, Edward D. Thimons

Aerodynamic stall of vane-axial fans is both an operational problem and a safety concern. While deep stall is relatively easy to detect, the diagnosis of a partial stall is often more difficult. Its transient nature and the fact that its symptoms can mimic electromechanical problems of the fan and fan drive assembly, or vice-versa, compound the difficulty of making a timely and accurate diagnosis. A knowledge-based expert system known as FANPRO has been developed to aid in the diagnosis of these problems. FANPRO and its application are the subject of this paper.

Jan 1, 1991