Search Documents

By Tzou-Shin Ueng

Rock reinforcement of rock anchors and rock bolts are commonly used for the support of large rock caverns. The rocks at the location of most large underground openings are usually under very high initial stresses prior to excavation. Hence, the stress redistribution caused by excavation will induce considerable rebound deformations of rocks surrounding the caverns. Since the pressures exerted by the reinforcement are generally far below the initial rock stresses, the reinforcement will be stretched along with the rock deformations, and the stresses in the reinforcement increase accordingly. It is not uncommon for the stress in the reinforcement to reach the yield strength, and in some cases the reinforcement may even have failed. Therefore, the increase of stresses caused by the rebound deformations of rocks should be taken into account in addition to the force required to stabilize the caverns. It was found that the measured stress increases of the prestressed tendons after installation were in good agreement with those computed based on the measured rock deformations between surface and the anchoring point of the reinforcement. The rebound rock deformations and the stress increases in the reinforcement can be estimated based on the results of the finite element analysis and experiences in previous field measurements incorporated with considerations of the geologic conditions, rock properties, rock reinforcement and construction procedures.

Jan 1, 1986

By J. J. Schwoebel

Resource Enterprises, Inc. (REI) is exploiting the coalbed gas resource by working in unison with active underground mining operations. At REI?s pilot project at the Soldier Canyon Mine, Carbon County, Utah, REI has drilled nearly 15,250 m of horizontal in- seam and slant boreholes during the initial two years of drilling activity. Produced gas has been sold to a natural gas transmission company on a continuous basis since mid 1983.

Jan 1, 1986

By C. W. Chiaretta

Utah Power and Light Company's Deer Creek Mine had been developed to a point where mine ventilation efficiency had declined to an unacceptable level. Problems identified were ventilation of inactive areas, excessive leakage, and restrictions in the return and intake air ways. Mine management implemented an intensive mine ventilation improvement program to alleviate future problems with respirable dust in the working sections and diesel equipment emissions. Program objectives included sealing of inactive areas of the mine, rehabilitation of high resistance areas, and construction of additional intake and return aircourses. Applications of computer modeling techniques are used to predict the effects of ventilation changes and improvements. Improvements are then prioritized to achieve the largest efficiency increases first. Actual real time assessment of the mine environment and ventilation changes are accomplished with a mine wide monitoring computer system. The Deer Creek ventilation improvement program has more than doubled the ventilating efficiency of the mine.

Jan 1, 1990

By R. A. Thomas, C. D. Litton

"The objective of this study was to develop a laboratory-scale method to rank the ignition and fire hazards of commonly used underground mine materials and to eliminate the need for the expensive large-scale tests that are currently being used. A radiant-panel apparatus was used to determine the materials’ relevant thermal characteristics: time to ignition, critical heat flux for ignition, heat of gasification, and mass-loss rate. Three thermal parameters, TRP, TP1 and TP4, were derived from the data, then developed and subsequently used to rank the combined ignition and fire hazards of the combustible materials from low hazard to high hazard. The results compared favorably with the thermal and ignition hazards of similar materials reported in the literature and support this approach as a simpler one for quantifying these combustible hazards. Resumen ¦ El objetivo de este estudio fue el desarrollo de un método a escala de laboratorio con el fin de clasificar los peligros de ignición y fuego de materiales comúnmente usados en minería subterránea y la eliminación las pruebas costosas y a gran escala que se realizan actualmente. Se usó un aparato de panel radiante con el fin de determinar las características térmicas relevantes de los materiales: tiempo de ignición, flujo de calor crítico para ignición, calor de gasificación y tasa de pérdida de masa. Se derivaron tres parámetros térmicos de los datos: TRP, TP1 y TP4, luego fueron desarrollados y subsecuentemente usados para clasificar los peligros combinados de ignición y fuego de materiales combustibles, de bajo riesgo a alto riesgo. Los resultados tuvieron una comparación favorable con los riesgo/peligro térmicos y de ignición de materiales similares reportados en la literatura y apoyan este enfoque como uno más simple para la cuantificación de estos riesgos combustibles"

Jan 1, 2015

By Steve Garcia

GEORGE WEINMAN: Our next speaker is Steve Garcia, operations vice president and general manager of mining at IMC-Agrico, Florida. Steve was born in Lakeland, Florida, to an IMC mining family. He has 17 years with IMC-Agrico and Freeport companies, including assignments in North Carolina, Nevada, Arkansas, and Indonesia. His work within the industry includes technical and operating positions including chief metallurgist, drying superintendent, and mines operations manager at Pane Creek. Other experiences include design of a grassroots phosphate facility in North Carolina; construction and start-up of a gold facility near Elko, Nevada; work in the Blytheville, Arkansas, ammonia urea facility; and three years managing engineering, construction, and support services in Irian Jaya, Indonesia. Steve's presentation is "Evaluation and Standardization of Multiple Slurry Pumping Systems."

Jan 1, 1998

By William Petruk

Performance assessments are carried out to monitor operations, to evaluate performance and to identify processing problems. The assessment involves collecting and analyzing representative samples from critical points in a flowsheet and interpreting the data. Sample analysis techniques include chemical analyses, mineralogical investigations, mineralogical analyses, and materials balancing. Chemical analyses provide the lowest cost assessment and should be used liberally, particularly in monitoring a process. Materials balances performed on chemical assays for a suite of samples are used as a first step in evaluating a process. Mineralogical investigations are more expensive than chemical analyses but need to be used only at the beginning of mining and metallurgical operations and as a second step in assessing processing problems. Quantitative mineralogical analyses combined with materials balancing provide the most complete performance assessment, but the procedure is expensive. On the other hand, the assessment has the potential of a large payback when carried out where warranted.

Jan 1, 1991

By Charles A. Hickey

The dining industry game tome Spruce Pine area a few years after tine Civil War. Two Yankees came down from Massachusetts to mine sheet mica to sell to the stove manufacturers for windows in heating stoves. At this time the method of mining was very crude; it was done only with pick and shovel. They were mining mica from the soft veins. Later they progressed to hand grilling and blasting. Hand drilling was quite an art in the area. One man would hold and turn the steel while one or two other men would drive the steel with hammers. In shaft raining, the muck and water was removed by hand winches called windlasses. About 1920 air compressors and jack hammers came into use. These were perhaps tide greatest improvement that has ever come to the area's mining industry. Later carne gasoline hoists, air drive water pumps, and all electrical equipment. Mica mining has, for the past few years, been very modern and efficient.

Jan 1, 1962

By R. Frenette, A. W. Mo, H. A. Hamza

Fine particles present major technical and economic problems to those who deal with solid/liquid separation processes. In the coal industry the problem is compounded by the large amounts of produced fines such as those present in Western Canadian coals. Flocculants in the form of high molecular weight water soluble polymers are commonly considered an effective solution for the enhancement of the separation process. These reagents are relatively expensive especially when considering a low-price commodity such as coal. Optimization of the use of these reagents is therefore an operational necessity. Six polymers were evaluated as to their effectiveness in flocculating a fine coal tailing. Results were compared with those for a reference flocculant, in-use at that time in the washery. It was shown that, in general, flocculants significantly improve the solid/liquid separation process. The ranking of the flocculants as to their effectiveness in settling and filtration indicated that the best flocculants for settling were not necessarily the most effective for filtration. Flocculants that showed the best filtration improvement were generally cationic and those best for settling were anionic.

Jan 1, 1988

By Arpad E. Torma

The electrochemical behavior of a zinc sulfide concentrate during the microbiological leaching was investigated using ZnS-carbon paste electrodes and a cyclic voltametric technique. The effects of Zn2 [ ] , Fe2+, Fe3+ and Cu2+ on the cathodic and anodic currents associated with zinc sulfide leaching in presence and absence of microorganisms, were assessed. The semiconductor nature of zinc sulfide was discussed in terms of ability of microorganisms to obtain their metabolic energy (through removal of electrons) from this high energy gap substrate. The intermediate electrochemical reactions involved in the ZnS leaching were described.

Jan 1, 1989

One of the major objectives of cost analysis is to enable the manager to predict the financial outcomes of decisions. To accomplish this, the future costs and benefits of alternative courses of action must be determined. If care- fully used, information about past financial performance can be helpful in this analysis despite the fact that, by definition, financial reporting information is historical. In many cases, both revenues and costs need to be estimated for decision- making. For the production manager, additional revenue is a result of increased throughput or recovery of valuable material from the stream of mined material. A reduction in operating cost, although similar to a revenue increase in its financial impact, is estimated using slightly different techniques. Generally, the estimation of cost is more difficult than the estimation of revenue. Most cost estimates have two components: an estimate of fixed costs and an estimate of variable costs. As discussed in chapter 5, the total cost of an activity during a specified period can be expressed as: Total cost = (Variable cost per unit of activity) x (Units of activity) + Fixed cost or TC = VX+F

Jan 1, 1999

This paper presents the development of a knowledge based integrated decision support system (E.X.I.S) for the extractive industries to provide information concerning the environmental impact of extractive operations on land quality, surface and ground waters, and the best solutions for the rehabilitation/revegetation of the waste disposal areas to the relevant target groups (extractive industries, regional authorities, national authorities, research institutes, public). GIS was integrated with the decision-making models for the rehabilitation and revegetation of mine spoil. The system design involves several steps including site selection ? mine type identification ? waste identification ? selection of rehabilitation (revegetation or other methods). The knowledge based model consists of two integral parts: the model base, in which the input data are processed and classified using special fuzzy algorithms and criteria and the knowledge model, which hosts the various decision algorithms concerning evaluation of vegetation covers, selection of trees and plant species, selection of rehabilitation and revegetation schemes and also economic analysis for each option. The system input will include parameters on site characteristics (climate, topography, geology, hydrology etc), waste type and properties (physical-geotechnical and geochemical data) as well as environmental parameters of the existing waste disposal area. Based on the values of the above parameters and the characteristics of the rehabilitation technologies developed worldwide, the system, using IF-THEN rules will define a list of appropriate techniques for the rehabilitation of the examined waste. Then, the model will involve the application of multi-criteria analysis (MCA), i.e. a structured system for ranking alternatives and making selections and decisions. Each technique shall be judged based on its behavior into four fields, i.e. financial, social, technical and environmental criteria. In turn these fields will be analyzed into a lower level of evaluation criteria.

Jan 1, 2006

By Jindrich Fiala, Jirí Kout

The paper contains knowledge that have been achieved when the problem of airflow temperature and humidity changes prediction in mine airways was investigated. The substance of physical processes has been consistently applied. The methods of dry-bulb and wet-bulb temperatures calculations can be applied in any type of mine airway. The exceptionality of auxiliary ventilated airways is in the original solution of so called losing air flowing when a ventilation pipe is leaky. The combination of aerodynamics and thermodynamics solutions enable to determine climatic conditions on projected workplaces with a sufficient accuracy.

Jan 1, 1991

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to operate in parallel with, and supplement, its two existing main fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) Carlsbad Area Office facility designed to permanently dispose of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for either modifying, supplementing, or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (K. McDaniel, et al., 1997) to: identify and quantify operational concerns, evaluate possible alternatives, and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans, and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness, and improving system performance. The fan installation project accommodates several operational and scheduling constraints. WIPP is scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP's ability to declare facility readiness and had to minimize operational disruptions during the system tie-in. All engineering for the project is completed and physical modifications started in July 1997. The project will be completed in early 1998.

Jan 1, 1998

By Alain Broussaud, Guy Fourniguet, Jacques Franck, Pierre Conil

Steady-state simulation is now in current use to assist mineral processing plant design and optimization. However, the reliability of results generated by simulators has not until now been seriously investigated. A simulator supervision algorithm was designed and programmed to study both the influence of the reliability of experimental data on the accuracy of unit operation model calibration, and the influence of unit operation model accuracy on the results of direct plant simulations. An application to a grinding flotation plant is described and discussed. The approach may open the way to the quantitative analysis of the risks taken in mineral processing projects, which would be similar to the application of geostatistics to mining projects.

Jan 1, 1990

By K. A. Natarajan, M. R. Sabari Prakasan

"Biodegradation of sodium isopropyl xanthate using two types of bacterial strains, Paenibacillus polymyxa and Pseudomonas putida, is demonstrated. At concentrations higher than 50 mg/L, the presence of xanthate in the growth medium resulted in bacterial toxicity, retarding growth kinetics. Adaptation through serial subculturing in the presence of higher xanthate concentrations resulted in the development of xanthate-tolerant bacterial strains. Stress proteins secreted by bacterial cells grown in the presence of xanthate were isolated. Bacterial cells could utilize xanthate as a growth substrate, degrading xanthate species in the process. Acidic metabolic products generated by bacterial metabolism promoted efficient xanthate decomposition. Probable mechanisms for the biodegradation of isopropyl xanthate are illustrated.IntroductionDifferent types of alkyl xanthates (ethyl, isopropyl, amyl, etc.) have been used as flotation collectors in the concentration of sulfidic ores for several decades. Large quantities of waste water and xanthate-containing effluents are generated by ore flotation processes, posing considerable environmental challenges. Billions of cubic meters of such process waste waters are produced annually across the world, most of which are discharged to the environment, often without any treatment. Leakages and accidental release of xanthate reagents from manufacturing plants and during transportation and storage can also contaminate the environment. Residual concentrations of xanthate reagents are encountered in waste effluent, which are found to be toxic to aquatic life and unfit for human consumption (Harris, 1984; Okibe and Johnson, 2002). Further, direct recycling of such waste waters for plant operations can compromise water quality standards required for process operations. The presence of residual xanthate in recycled waters from flotation plants deleteriously influences flotation processes. Xanthate can be easily decomposed at low pH values; however, CS2, which is more toxic, will be produced by the acidification of neutral and mildly alkaline xanthate-containing solutions. Physico-chemical methods such as flocculation, chemical oxidation and decomposition and physical adsorption used to remove residual collector reagents from mill process waters are often expensive and not environment-friendly (Oliveira and Rubio, 2009; Cheng et al., 2012; Molina et al., 2013,)."

Jan 1, 2015

By Prasad S. Mulukutla

INTRODUCTION The use of specialty chemicals In mining Is an Important consideration In determining the economic efficiency of a floatation plant. The plant metallurgist would like to maximize the recovery of valuable minerals while maintaining an acceptable grade product. The direct cost of the reagents, while significant, Is only a part of their economic effect. Reagents determine the flotation rates and the selectivity of the mineral separation. In flotation practice, mineral selectivity can be achieved through the addition of various reagents that can control the wettablllty of a particular mineral In the flotation pulp. The reagents which will generally optimize the flotation process are commonly classified Into three distinctive categories: collectors frothers and modifiers. Large tonnages of metal sulphide concentrates which are the source of most of the common base metals are produced economically by fairly standard flotation techniques. The advent of modern technology coupled with the necessity of processing finely disseminated and complex ores of low grade has Increased the need for utilization of non traditional and high selective chemicals reagents for the economic recovery of metals and raw materials. Mining operations in developing countries continue to progress at a rapid growth as many countries mine and process both metallic and nonmetallic ores. The total mine production of base metals, precious metals, Iron ores and coal In developing countries In Africa, Asia and South America has been much higher as compared to the western world production In terms of tonnage and dollar value. Global capital Investments In mining during 1991-95 Is $ 55.1 billion and It Is anticipated that the development of new and specialty reagents may be concentrated In the processing of aluminum , copper, precious metals and Industrial minerals with special reference to potash, phosphates, kaolin and silica sands.(1) The challenge for the design and development of new specialty chemicals Is dependent on Its cost performance and environmental acceptability. Information on the theory and application on the development of mining chemicals has been reviewed In several conference proceedlngs,(2-4) publications(5) and also discussed by several Individual authors.(1,6-10) These publications serve as a comprehensive reference source on the reagents used In several flotation processes. This paper discusses the present trend in the use of specialty mining chemicals In diversified mining operations on several mineral systems with particular reference to sulfide ore systems. The necessity to expose these specialty chemicals through aggressive marketing techniques In mining operations In many developing countries Is also presented. SPECIALTY CHEMICALS Specialty mining chemicals, like other specialty chemicals, share common business characteristics that transcend geographic boundaries. They are manufactured 1n a few selected areas, generally expensive relative to commodity chemicals, shipped and compete globally and usually require specialized knowledge for proper use. Specialty mining chemicals are relative newcomers to chemical markets. The vast majority of mining chemicals are derived from products that are less than two decades old. Traditional collectors and frothers have been available for a considerably longer time. The emphasis on adding value to existing products and byproducts Is responsible for several characteristic features of the mining chemicals business. Most raw materials for these chemicals are related to oil and gas byproducts, chemical refineries, pulp and paper mills and all chemical manufacturers. Until the last several years these operations were located In Industrialized countries, while a significant number of mining chemical users were In developing countries. Therefore International trade In mining chemicals developed through agencies or agents in each particular country.

Jan 1, 1993

By Richard Stoltz, Gary Smith

This paper presents the findings of a face ventilation investigation, conducted by the Ventilation Division, Pittsburgh Health Technology Center, at a underground coal mine operating in the Illinois No. 5 coal seam. The purpose of the investigation was to evaluate the effectiveness of a blowing face ventilation system in controlling methane liberation in the face area while mining with brattice distances up to a maximum of 40 feet from the face (extended cut). The continuous miner on this section was remotely controlled and equipped with a machine mounted dust collector. Data collected during this investigation included methane concentrations, intake and return air quantities in the face area, and scrubber air quantities. In addition, a time study was conducted to correlate the methane peaks to activities in the face area. In conjunction with the face study on Section A, separate methane liberation studies were conducted on three additional sections: B, C, and D. This was done in order to compare intake methane concentrations and methane liberations from other sections in the mine to the test section. Calculations indicated that the minimum intake air quantity necessary at the inby end of the line brattice for the section investigated was 7,000 cfm. Due to the higher intake methane concentrations and average methane face liberations measured on three other sections, the minimum air quantities necessary at the inby end of the line brattice were determined to be 13,900 cfm, 11,100 cfm, and 15,000 cfm, respectively.

Jan 1, 1991

By M. Misra, J. Nanor

The removal and stability of arsenic over a wide pH range (3.0-10.0) from synthetic solutions and industrial waste effluents (including mining waste tailing slurry) can be accomplished with addition of impure lanthanum chloride alone or in conjunction with ferric sulfate. The long term stability of these correspond­ing precipitated compounds is critical from the disposal stand­point. In this paper test results of this new process for arsenic removal and stabilization from the above mentioned systems are presented. Also, precipitated arsenic compounds (lanthanum arsenate, lanthanum-ferric arsenate, ferric-lanthanum arsenate and ferric arsenate) from synthetic solutions have been charac­terized. The characterization technique used was XRD. XRD patterns which shows that the lanthanum arsenate and lan­thanum-ferric arsenate formed in acidic and alkaline pH at room temperature are crystalline. On the contrary, ferric arsenate and ferric-lanthanum arsenate compounds formed under the same conditions as lanthanum arsenate were amorphous.

Jan 1, 1998

By M. Kumral

The in-situ mineral characteristics of a deposit are simulated by sequential co-simulation and averaging the simulated characteristics within specified block volumes creates a three-dimensional block model. This model is then submitted to optimal open pit and production scheduling algorithms. As the market values of industrial minerals depend on the satisfaction of predetermined blending criteria rather than metal content, a Linear Programming (LP) scheme has been used to identify all blocks that can be included in the blend without violating the grade requirements. The Lerchs-Grosmann algorithm using the blocks identified by the LP program determines optimal pit limits. All blocks that lie outside the optimal pit are removed from the system and the blocks within the optimal pit are submitted to the production-scheduling algorithm. Production scheduling optimisation is done in two stages: Lagrangean parameterisation, resulting in an initial sub-optimal solution, and multi-objective simulated annealing (MOSA) improving the sub-optimal schedule further.

Jan 1, 2002

By R. Houot, C. Leschevin, G. Gillet

In mineral processing, conventional magnetic separators are equipped with traditional magnetic circuits (magnetic iron yoke with copper coils or iron-clad solenoid) that develop magnetic fields of less than 2 T'. For minerals of low magnetic susceptibility, use of these circuits has many disadvantages. Only a separator with a superconducting magnet can contribute to solving the problems and produce a high magnetic field. This paper presents and describes a magnetic separator having a superconducting magnet with integrated closed circuit for helium liquefaction. The system generator and maintenance are simplified by extensive automation realized by a versatile program- mable autocontrol unit. A comparative study if the results on concentration and purification of different raw materials with the new and with conventional separators is described.

Jan 1, 1987