Search Documents

By K. E. Hjelmstad

Solution mining operations often encounter difficulty maintaining adequate leach solution flow into the ore formation because of loss of formation permeability near the injection well. Permeability loss caused by swelling and breakup of clays and fine particle migration can often be the cause of the problem. Combined permeability and leaching tests were done in the laboratory on samples of clay bearing ores to evaluate a clay-stabilizing polymer's effectiveness in preventing the problem. Test results indicate that treating the ores with cationic polymers could maintain permeabilities two to five times greater than the long-term permeabilities present in untreated ores. Both alkaline (pH 8.5) and acidic (pH 2.0) leaches were used in the permeability leaching tests. To determine the reasons for the success of the clay stabilizing polymer, clay swelling tests and zeta potential measurements were made on untreated ore samples and on ore samples treated with the cationic polymer. Test results indicate the cationic polymer could reduce the degree of negative charge on fine particles and their tendency to disperse, as well as reduce clay swelling. Test results indicate a potentially beneficial effect on operating parameters such as capacity and injection pressure during leaching, if clays and fines are kept stabilized. This may be done by treating the zone of high fluid velocity near injection wells with cationic polymers.

Jan 1, 1991

By David Brown, Glen Hall, Ken DeVos, Frank Barone

Dredging and Flooding was completed on the Falconbridge Limited "New Tailings Area" in the period from 1996 through 1998, as part of their site closure measures. Part of the decision making process and closure planning was water quality prediction, including oxidation and diffusion modelling. The purpose of this modeling was to define the potential water quality that would result during and after dredging. A significant body of research on the geochemistry and oxidation kinetics of this site had been compiled. The results of the modeling provide practical insight on the potential water quality that may be expected. Water quality in the pond has steadily improved since flooding was completed with the exception of short term peaks during spring runoff. Aquatic vegetation is appearing through natural recovery and transplanting of local species, and colonies of minnows are now observed in the ponds.

Jan 1, 2000

By Terry Ritzel

Predictive maintenance technologies include vibration analysis, tribology, infrared thermography, ultrasonic detection and electrical measurements. These technologies have been applied to large electric mining shovels at the Cyprus Sierrita Mine outside of Tucson, AZ. The predictive maintenance program was initiated on the P&H models 2300 and 4100 electric shovels during August 1996. Results of these technologies have shown the potential for improving electric min- ing shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition-based planning of component replacement. Maintenance costs are minimized by focusing resources through condition-based prioritization.

Jan 1, 1997

By D. W. Fuerstenau

One of the more energy-efficient methods for size reduction, namely particle-bed comminution under high compressive loads, was employed to grind eight minerals and ores, using up to 250 MPa pressure. A new approach based on the self-preserving character of the ground product size distributions and a linear energy-reduction ratio relationship is proposed for analyzing this mode of size reduction. The grind ability of the material when comminuted in a particle bed is about one-half that of the single-particle crushing mode, which is in agreement with previous estimates of the relative efficiencies of energy utilization based on direct measurements of surface area produced. The loss of efficiency may be attributed to energy dissipation by particle interaction phenomena in compressed beds.

Jan 1, 1993

By A. J. S. Spearing, G. Bylapudi, K. Mondal

The mining industry is a major consumer of rock anchors in the United States. Due to the high humidity in the underground coal-mining environment, the rock anchors corrode and lose their load bearing capacity, which, in turn, reduces the life expectancy of the ground support. This creates operational difficulties and a number of safety concerns (Li and Linblad, 1999). Research on rock anchor corrosion has not been adequate in the past and the effects of several factors in the mine atmosphere and waters are not clearly understood. One of the probable reasons for this lack of research may be attributed to the time required for gathering meaningful data. Underground water samples from different mines in the Illinois coal basin were collected and the major chemical content was analyzed and used for laboratory testing. The corrosion performance of the different commercial rock anchors was investigated by techniques such as laboratory immersion tests in five different corrosion chambers and potentiodynamic polarization tests in simulated ground waters based on the Illinois coal basin. The tensile strengths were measured for the selected rock anchors taken every three months from the salt spray corrosion chambers maintained at different pH values and temperatures. The corrosion potential, corrosion current and the corresponding corrosion rates of the #5, #6, #6 epoxy-coated and #7 forged-head rebar steels, #6 and #7 threaded-head rebar steels were measured in the pHs of 5 and 8 at room temperature. The open circuit potential (OCP) readings of the different rock anchors were recorded in three selected underground coal mines (A, B & C) in the Illinois coal basin and the data compared with the laboratory electrochemical tests for analyzing the life of the rock anchors installed in the mines with respect to corrosion current measured.

Jan 1, 2010

By Paul C. Schmall, Arthur B. Corwin, Hugh S. Lacy, Derek Maishman

For reasons of hydraulic design and constructability, water supply tunnel systems are often located relatively deep, in competent rock. Where the rock lies below a thick cover of water bearing soils, artificial ground freezing offers a low risk, cost-effective method of constructing access shafts. Several examples, in Kansas City, MO and in Brooklyn and Queens, NY, illustrate the use of freezing to provide structural support and ground water exclusion. In the case histories presented, the shafts range from 6m to 12m (20 to 40 ft) in diameter and soils vary from clays to boulder beds with depths in excess of 73m (240 ft) to competent bedrock. Where tunnels for infrastructure are designed to be driven in rock, vertical access may encounter a considerable thickness of overburden soils with groundwater. In such cases, shaft sinking problems are analogous to those confronted by mining engineers over 100 years ago. At that time, newly developed refrigeration machines were set to freeze the ground water and stabilize running sands. Although modern technology has refined our efforts, the basic features of the ground freezing to be described here are the same as those used in the last century. Vertical holes drilled on a circle surrounding the shaft site are equipped with leak-free steelpipes through which a refrigerated brine is circulated. In this manner, a frozen cylinder, seated in rock, is formed when the earth freezes between adjacent pipes. Shaft excavations take place inside a self-supporting, ground-water excluding structure. For mines, no better method of sinking production shafts through deepwater-bearing ground has yet been established. Indeed, major deposits of coal, potash, and salt would have remained inaccessible to this day were it not for the continued use of artificial ground freezing. If mine shaft freezing became relatively commonplace, early applications to civil engineering were few. Mussche and Waddington (1946) mention only five projects between 1892 and 1935; three of these relate to subway or vehicular tunnels in Paris, Antwerp, and (the most extensive) at five locations of the Moscow Metropolitan Railway development. In the United States, the method was used to spectacular effect in 1936, freezing about 3,000 cubic yards of silt to stop a slide

Jan 1, 1999

By Gurses Oner

In situ leaching is a relatively old mineral extraction method; however, historically only a small portion of copper has been produced from small scale operations. Recently, in situ leaching technology because of its intrinsic advantages over conventional mining and milling is being considered as a viable option for recovering copper from both low grade oxide and sulfide deposits. This paper presents the application of computers to investigate in situ technology using large whole core leaching experiments. Computers were applied to three different areas: (1) experimental control and data acquisition, (2) non-destructive evaluation of samples using x-ray computed tomography and image processing and (3) mathematical modelling and data analysis.

Jan 1, 1992

By Jozef S. Stachulak, Bruce R. Conard

INTRODUCTION The concern of occupational exposure to diesel exhaust pollutants is an important workplace issue for the mining industry. During the last three decades of diesel operations at Inco, a significant amount of research and improvement has been made in the area of work environment, and effective diesel operation. This paper will review the experience gained by Inco's Ontario Division from the implementation and the use of modern engines, improved fuel quality, and the exhaust control technology, coupled with adherence to proper maintenance and ventilation design and practices. Past monitoring practices and the current occupational monitoring program at lnco are outlined. A major new research initiative involving multi-stake holders in diesel performance is described. MINING IN THE SUDBURY AREA The discovery of nickel-copper ore in the Sudbury area dates back to the year 1856. The existence of this orebody was noticed when a strong compass deflection was observed by a provincial surveyor. This discovery, even though documented in official re- ports, failed to arouse any public attention at that time. In 1884, a rock-cut was blasted through a small hill near the village of Sudbury to permit laying track for the Canadian Pacific Railway (Boldt 1967). The rock-cut uncovered a body of massive sulfides with a copper content of over nine percent. The mineralization is concentrated along the outer margin of the Sudbury Basin, an oval-shaped structure having a dimension of 55 x 95 kilometres. The ore extends down-dip to to at least 3000 metres below the surface. The mining methods at lnco can be divided into two categories: "filled-stope" and 'bulk" mining. This division, in the broad sense, may also reflect the environmental conditions of the mine. In the past, the selection of a mining method was based on the size, shape, grade and the strength of the ore and its surroundings. The recent development of improved technology and mining equipment permitted wider application of low cost bulk mining methods. UNDERGROUND DIESEL EQUIPMENT The first diesel-powered machine, a 145-horsepower scooptram, was put into operation in March 1966, in a cut-and-fill stoping complex at Frood Mine. The number of diesel machines underground in the Inco, Ontario Division, mines was increased to 360 units by 1971,550 in 1977 (Rutherford 1978), and over 830 diesel-powered units in 1995. The following list indicates current mobile diesel equipment. LHD 194 Loaders 81 Trucks 28 Jumbo Drills 78 Personnel Carrier 101 Service Equipment 155 Locomotives 50 Bolters 30 Scissor Lift 113 About 20 percent of the LHD and truck units are equipped with electronic fuel controlled engines. COMPOSITION OF DIESEL EXHAUST Diesel exhaust contains hundreds of pollutants (Watts 19921, including components of unburned fuel and lubricating oil and products of incomplete combustion of the fuel and oil. These pollutants are emitted either as gases or as particles. Gaseous pollutants include carbon monoxide, nitrogen oxides, and sulfur ox- ides, as well as a variety of organic compounds, such as hydro- carbons, aldehydes, and polynuclear aromatic hydrocarbons. The particle phase, also known as diesel particulate matter (DPM), is the filterable portion of diesel exhaust. Figure 1 depicts the trimodal particle size distribution that arises from different mechanisms of aerosol generation (Cantrell and Rubow 1992). Primary combustion aerosols, including diesel exhaust aerosol, are formed as very small particles (in the 0.001 to 0.08 micrometre range), but physical mechanisms such as condensation and coagulation quickly transfer the aerosol mass from the nuclei mode to the accumulation mode. These processes result in a mass median diameter of approximately 0.2 micrometres for diesel particulate matter, and 90% of the particles are less than 1.0 micrometre in size. These particles have a high surface area, permitting the adsorption of different substances produced during combustion. Mechanically generated aerosols, on the other hand, typically contain particles greater than 1 micrometre in diameter. The particle phases of diesel exhaust contain three components (Bagley, et al, 1996) shown by Figure 2, namely: a carbon- aceous fraction composed mainly of solid-carbon particles, a sulfate fraction containing small hydrated sulfate particles, and a soluble fraction that contains compounds that are soluble in organic solvents and are adsorbed or condensed onto carbon core particles. These compounds consist primarily of higher molecular weight hydrocarbons and PAH's and may contribute 15% to 45% of the weight of the total particulate matter (Schuetzle, 1983). The control of these pollutants is necessary to ensure a healthy work environment. Proper engine maintenance, engine design modifications, improved fuel quality, and use of exhaust control technology, coupled with good ventilation practices, all

Jan 1, 1997

By Kenneth R. Miller

Surface mine equipment operators in the Campbell County region of Wyoming's Powder River Basin have found new ways of solving old problems. Technology, experience, competitive pressures and an increasing grasp of economies of scale have driven mine operators, equipment manufacturers and suppliers to specialization of applications. In economic terms, today's coal price of $4.95/t ($4.50/st) equates to $2.53/t ($2.30/st) in 1980 terms - an incomprehensible value at that time. This article describes some examples of change and adaptation made by Powder River Basin coal operators in overburden stripping equipment and techniques. It focuses on the evolution of the design and use draglines, shovels, trucks, scrapers and dozers.

Jan 1, 1998

By P. T. Luckie

The selectivity curve -- a continuous function which predicts the expected proportion of feed material of a particular size that will appear as coarse material -- is the preferred model for describing classification. In a previous paper (I), the authors presented a technique for determining the selectivity curve of a classifier from experimental data. The separation process is defined by a binomial distribution of the form [ ] where s(x), the probability of particles of size x reporting to the coarse stream, is obviously the selectivity value for material of size x.

Jan 1, 1975

By Lei Zhang, Zhibo Ma, Pingye Guo

The mechanical behavior of hard roofs often leads to significant deformation and strong mine seismicity in gob-side entry retaining (GER) of the longwall mining, affecting the mining safety and efficiency of coal mines. Field investigations indicate that the failure process of the retained entry by hard roofs can be divided into three stages. In this paper, theoretical analysis and numerical simulations are first used to evaluate the damage process of the retained entry under the hard roof. The results show that the instability of the retained entry in the conventional GER method results from the combined static-dynamic loads (in stage II and stage III) from the hard roof. Then, an innovative method, through fracturing roofs to maintain entry (FRME), based on GER with the hard roof is introduced to solve this problem. In this method, the roof of the mining area is pre-fractured, and when the coal seam is mined, the direct hard roof will collapse along the fractured surface due to its deadweight and mining pressure. The hard roof control effect on the static and dynamic loads, taking into account the innovative method, is verified with simulations and theoretical analyses. The results are compared with those of the conventional GER method. Furthermore, based on the numerical simulation study of dynamic responses, it is found that compared to the GER method, the dynamic response of the retained entry using the innovative method is more moderate and more conducive to the stability of the entry. Field application also validated the effectiveness of the innovative method to control the mechanical behavior of the “massive sudden collapse” of the hard roof.

Aug 14, 2023

By Robert L. Runkel, Kenneth E. Bencala, Briant A. Kimball, Katherine Walton-Day

The solute-transport model OTIS and the reactive solute-transport model OTEQ were used to simulate geochemical conditions in Cement Creek, a tributary to the Anirnas River in Colorado. OTIS was used to depict instream zinc concentrations, and to simulate the effects of two remediation scenarios on zinc concentrations at the mouth of Cement Creek. These simulations do not account for effects of changing stream pH on metal concentrations. Preliminary simulations using OTEQ to account for instream pH changes were unsuccessful due to the spatial nature of mixing processes, and insufficient information about the thermodynamic properties of precipitates forming in mixing zones.

Jan 1, 2000

By J. C. Irvine

A recent development in underground drilling has been the introduction of the down-the-hole drill, an old and very familiar tool to the surface operator. The idea of moving such a rig underground is not new. Tests were conducted at INCO in Canada and Mt. Isa, Australia in the early 1960's, and St. Joe used one for underground exploration in their Missouri lead mines in the mid-1960's. However, the trend to full scale production programs did not start until the mid-1970's. The first successful North American test was at INGO in early 1973. This led to a large-scale pillar recovery and open stoping program which en¬compassed 25 drilling units by mid-1976. Meramec Mining Company tested a unit using air boosted up to 200 psi (140, 000 kg(m2) in the summer of 1973 which by 1976 led to an open stope and pillar drilling program using 12 units. By mid-1976, production units using boosted air were also in use at Pilot Knob in Missouri and at St. Joe in Balmat, New York. Experimental and utility units were in use in several other mines and down-the-hole drills were being seriously considered for at least one major new underground mine.

Jan 1, 1976

By L. B. Rothfeld

In anticipation of RCRA reauthorization and subsequent rulemakings, the Bureau of Mines is studying potential economic impacts of RCRA on mining. For U.S. copper heap and dump leaching operations in a variety of terrains, the cost of liners and closure caps to comply with RCRA Subtitle D ranges from $55 million to $158 million per site, or about $500,000 per hectare ($200,000 per acre). If RCRA technology requirements and financial assurance had been required on current operations, 27 to 100% of production from heap and dump leaching would have been non-competitive at market prices between $2,310 and $1,650 per metric ton ($1.047 and $0.75 per pound) copper. This result is based on an analysis that considers return on capital, corporate overhead, marketing, and freight costs as well as operating and maintenance costs at the mine. Over the same price range, economic analysis using the IMPLAN input-output model on one-or two-county regions indicates potential net job losses of about 570 to 2,700 jobs. Total economic output of those counties could be reduced by about $180 million to $360 million.

Jan 1, 1994

By William W. Kephart

Brockway Glass Company, Inc., manufactures glass containers at fourteen plants located in nine states. The relatively high place value of the major glass batch components dictates that raw material supplies be obtained from numerous sources in the United States and Canada. One objective of our central composition control program is to arrive at a glass composition with similar physical properties at each of our plant locations. This requires that adjustments be made in the batch compositions to compensate for chemical variations from one raw material source to another. Minor chemical variations will occur in sand, limestone, and dolomite from one source to another. Major variations are present in the alumina sources because of the diverse rock types utilized.

Jan 1, 1973

By Kent S. Roessler

The Bureau of Mines is currently investigating the geophysical application of Tomography to monitor leachate during in-situ mining. Determining the location of the leachate is important for both economic and environmental reasons. By analyzing a sequence of tomographic images, we can determine where highly permeable/fractured regions are located and hence, major flow paths. Since BOMTOM (Bureau Of Mines TOMography - Tomographic Reconstruction Program), and BOMCRATR (Bureau Of Mines Curved RAy Tomography - Tomographic Reconstruction Program) are sensitive to user-selected ray path arrival times, we are also investigating the use of neural networks to automate the process of recognizing this feature. This paper presents a technique for detecting fracture zones and their orientations in a region between two boreholes, by using a motion analysis study of a sequence of tomographic images. It also addresses the need for an automated/unbiased method to pick crosshole seismic arrival times using a trained neural network. In exploration geophysics, the picking of first break arrivals represents a pattern recognition task. The neural net paradigm has proved to be a good method of solving this type of task. To pick the first arrival peak of a trace, the network is trained with a set of known (user selected) first arrival peaks by creating a binary image of a set of traces. Once trained, the neural net correctly picked first arrivals of the remaining traces in the set.

Jan 1, 1992

By Alfred G. Hoyl

The author, in exploring a virgin area vertically in two known ore shoots requiring decline shaft sinking, drifting, crosscutting and diamond drilling, chose to use electric, electric hydraulic, and diesel rubber-tired equipment. A rebuilt hoist, and electric hydraulic shaft shovel (mucker), hydraulic sinking drills, single boom electric hydraulic jumbo, electric hydraulic LHD, and electric hydraulic diamond drill were used successfully. Slides of the equipment and its use are shown. The advantages and disadvantages of the equipment are discussed, together with costs and production.

Jan 1, 1984

Automation and robotics are the keys to new intelligent autonomous mining systems which can remove operators from the hazardous and stressful mining environment and provide the tools for greater productivity. This pa-per presents the components necessary for a mining Intelligent Task Control System (ITCS) in dynamic unstructured mining environments. The proposed concept is applied to develop the ITCS for an autonomous excavator. The design and implementation of a fuzzy logic controller for an excavator that uses force/torque sensor feedback to complete excavation tasks is presented. Initial experimental results are also given.

Jan 1, 1994

By W. E. Foreman, A. Hayatdavoudi, A. Ghalambor

The objective of this investigation was to determine the sensitivity of three selected input parameters in the operational control of continuous bottom fed thickeners used for the treatment of coal refuse slurries. The three variable parameters were "Feed Flow Rate," "Feed pH," and "Feed Solids Concentration." These three input parameters were studied under three cationic-anionic polymeric conditions. For each polymeric condition, two mathematical models were developed, one for overflow response and the other for underflow response. The combination polymers produced the best quality of overflow and underflow. For this polymeric condition, change in the feed solids concentration was the most sensitive factor in the maintenance of the overflow quality, and the feed pH was the most sensitive factor for the maintenance of underflow quality. The mathematical models generated a set of plots that would allow an operator to control and/or adjust any of the three variables to achieve optimum conditions.

Jan 1, 1991

By Takashi Goto

In 1968 three historical rockbursts had occurred at Bibai Coal Mine in Hokkaido. At the time they had been observed by several seismic observatories as natural earthquakes away more than 100km from Bibai City. These facts taught us that the occuerrence of failure yielded in underground opening that was accompanied with seismic wave could be observed by seismometer on the surface. After two years from this desaster, the study concerning to microseismic events generated from underground mining panels has been begun by researchers with heart-throb.

Jan 1, 1982