Search Documents

By Paul C. Miclea

Hanford Reservation, in the State of Washington, with its deep basalt formations, is one of the three sites recommended by the Department of Energy for detailed investigations in order to select the first nuclear waste repository in the United States. Information obtained from several deep bore-holes drilled at Hanford indicates that the underground facility can be developed in one of the major basalt flows belonging to the Grande Ronde Formation in the Columbia Plateau, at depths greater than 3200 ft. One of the main concerns in the underground repository design is the achievement of acceptable environmental conditions during the development and the operation of the repository. For this, ventilation and air-conditioning are of prime importance and should be fully addressed. Besides the factors that determine the airflow requirements to meet the personnel and equipment operation needs, there are two major concerns that impact on the ventilation system design: the temperature of the in situ virgin basalt rock and the influx of groundwater. These two factors are related by the fact that the groundwater has the same temperature as the rock itself and they both constitute main sources of heat underground. Current information indicates that the temperature of the virgin rock at a depth of around 990 m (3250 ft) is 52°C (12S°F). However, there are some indications that the rock temperature at the selected horizon might be higher. This paper addresses the impact of the virgin rock temperature on the ventilation system and air-cooling requirements. Graphs with heat loads and cooling required for different rock temperatures have been prepared for a given model and network, using computer techniques for simulating the climatic parameters.

Jan 1, 1987

By Keith Whiting

The Van Stone zinc-lead mine is located in northeastern Washing- ton in Stevens County. It is about 24 km (15 miles) south of the Canadian border and 48 km (30 miles) west of the Idaho line. The deposits occur in late Cambrian age limestones and dolomites of the Metaline Formation. The bedding controls the trend of the zones containing the lenses of zinc-lead mineralization. The Van Stone property and vicinity is almost entirely covered with glacial drift averaging perhaps 6 m (20 ft) in thickness. Outcrops are very sparse. Outcropping gossan with zinc mineralization was first discovered by George Van Stone in 19 13, in what is now known as the South Ore Zone. Only minor trenching was done at that time. The property was idle until the mid- 1920s when Hecla Mining Co. drove several short adits and performed minor diamond drilling. In 1938, Willow Creek Mines of Nevada Inc. acquired the Van Stone plus adjacent parcels and commenced drilling on the known South Ore Zone. In the course of an expanded drilling program, the nonoutcropping North Ore Zone was discovered and was drilled out along a N30°E strike for about 305 m (1000 ft), beyond which point no mineralization was intersected.

Jan 1, 1991

By Earl M. Frizzell

This paper addresses considerations for the use of artificial support of pit walls in surface mines, a new project of the Bureau of Mines. Results to date indicate that a polymer-coated cable with embedded grit could provide good anchorage for stabilizing benches and highwalls, and an electronic method of recording discontinuities in the field is being reviewed and developed for application to mining. The objectives of the work in progress are to define the engineering parameters and evaluate the concepts for artificial supports in order to provide safe working environments when pit slopes are steepened to increase ore recovery and reduce overburden handling.

Jan 1, 1986

By C. R. Daly, D. Biswas

This study presents the development of a simplified artificial neural network (ANN) for the characterization of rock mass with a simultaneous display of its output in a three-dimensional interactive environment as well as in the form of a text document. The system was developed using JAVA object-oriented language, virtual-reality modeling language (VRML) and JavaScript, and it runs on the Internet. The user can walk through a three-dimensional virtual roadway, checking the underground rock mass behavior and, consequently, can design a support system. The system first characterizes the rock mass with the help of a neural network and recommends a suitable support system for the particular geomining condition. The system then represents its output in a three-dimensional environment. The neural network developed in this system was trained with 261 data sets, and its performance was evaluated with five case histories. The evaluation results showed that the network could identify the rock category and support system adaptively. The average error for the support load was 2.7%. Among the five case histories, two were represented in a three-dimensional environment. The output obtained from the overall system compared favorably with the existing underground conditions.

Jan 1, 2003

By Edwin H. Bentzen, Immo H. Redeker

Important industrial minerals are separated and concentrated by froth flotation by industry today. The following descriptions are presented as an overview of the methods employed to separate and recover a few of these industrial minerals. The minerals described in this section of the book are not, by any means, the only important minerals treated by froth flotation. Other minerals, such as calcite, kaolin, wollastonite, rare earths and vermiculite were not included, primarily due to the confidential nature of the information held by the Minerals Research Laboratory and the Colorado School of Mines Research Institute. Flotation of nonmetallic minerals is sometimes viewed as alchemy. However, the art is, in reality, based on sound chemistry, experience and a little luck in the treatment of new ores. In the flotation of nonmetallic minerals, as opposed to base metal sulfides, highly specific treatment conditions are required to accomplish separations. The presentation of the treatment of each of the minerals described was outlined as follows: DEPOSITS PROCESSING SPECIFICATIONS FLOWSHEETS (in some cases) A presentation of the factors, often critical, which must be carefully investigated to accomplish successful flotation of nonmetallic minerals is presented in the section on Sulfonate Collectors, elsewhere in this volume.

Jan 1, 1986

By R. H. W. Chadwick

We in Kennecott are well aware that Alaskans are interested in the progress of our project at Ruby Creek. We would very much like to be able to present you with a final report at this time and tell you about a new mine. I'm afraid, however, that it will be several years at best before such a report can be made. This, then, is an interim report to describe briefly some of our findings to date, and to acquaint you with some of the problems, both geologic and economic, which must 5e resolved favorably before we can talk about a mine. There are several things about this project which make it unusual and interesting to those of us who have been connected with it. Firstly, there is the fundamental importance to Alaska, in the present stage of its economic history, of any undertaking which offers promise of turning a natural resource into a competitive export product. I am sure all of us would get a lot more satisfaction out of having a part in bringing in a new mine in Alaska than we would out of adding another one to the long list in, say, Arizona.

Jan 1, 1960

By V. Perdikatsis

The aim of this paper is the study of the pollution of soils in greenhouses because of the use of pesticides. The degree of pollution was studied in relation with the mineralogical and pedologic properties of the soil. The study was con-ducted in the region of Kountoura, Palaiochora, situated in the south of the prefecture of Hania/Greece. Several samples of soil, originated from 4 greenhouses were analyzed. 5 pesticides with organic drastic compounds were chosen for analytical determination using GC-MS from 18 which were applied in total during the period of sampling. It was concluded that the adsorption of pesticides in the soil of greenhouses is connected with the percentage of the clay fraction and the content of organic carbon.

Jan 1, 2006

By John T. Cumberlidge

The Groveland deposit, in the Upper Peninsula of Michigan, consists of an E -W trending overturned syncline of Middle Precambrian Vulcan iron formation. At Groveland, the Vulcan formation can be divided into four units or facies. The total succession may be more than 550 feet thick, and consists of a basal unit composed of a lean chemical quartzite with traces of magnetite; a non-banded, partly clastic unit characterized by the preponderance of hematite over magnetite; a transition unit of well-banded magnetite-bearing iron formation interbedded with non-banded oolitic hematite; and a well-banded magnetite-quartz silicate unit at the top of the exposed sequence. The present magnetite-hematite ratios of different units within the orebody are considered to be a primary (post-diagenetic) feature of the original sediment. Subsequent regional metamorphism has increased the grain size of the original iron oxide minerals, but did not appreciably alter the oxidation state of the original sediment.

Jan 1, 1964

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. The roof bolts tested are also used to identify the possible corrosion mechanisms that influenced the bolts’ performance over time. Initially, the most commonly used bolt material in the USA, the ASTM A615 grade 60 steel roof bolts, was tested with and without stresses in a simulated underground coal mining environment for approximately 6 months, and the results are discussed. Localized corrosion forms such as crevice and pitting were mainly observed after testing. The stressed and unstressed roof bolts with and without threads that were tested in alkaline coal mine corrosive environment for 6 months passed their load-bearing capacity as per ASTM F432 test standards. From the results, it is concluded that this test protocol could be applicable to test the material performance of different roof bolt metallurgies and coatings with desired modifications to the proposed methodology for the specific underground mine environment. This paper mainly discusses the test system and protocol and shortcomings of the system and makes recommendations based on the observations and results.

By Guy D. Bruno

Through the remainder of this century, world consumption of fluorine per ton of primary aluminum produced will continue to be substantially reduced. Growth of the primary industry will offset some of the unit consumption, but demand for new fluorine sources will decline sharply. Continued application of dry fume scrubbing systems will be the most significant factor in reducing demand.

Jan 1, 1978

By G. T. Adel

The selective recovery of fine particles by flotation has been a long-standing problem in the mineral processing industry. Fundamental studies carried out at Virginia Tech since 1980 have suggested that many of the problems encountered in separating fine particles can be alleviated by using significantly smaller air bubbles than those used in conventional flotation processes. The main advantage of using smaller bubbles is found in an increased recovery rate, which can be attributed to an improved bubble-particle collision efficiency. This concept has been applied in column flotation as a means of improving flotation kinetics. A computer simulator has been developed to better study the effects of various parameters on flotation column performance. The simulation results suggest that the use of small bubbles and tall columns improves the recovery of fine particles while a judicious use of wash water greatly improves product quality. Information collected as a result of this analysis has been applied in developing scale-up relationships for column flotation.

Jan 1, 1989

By R. Velkova, D. Bojinova

The objective of the present investigations is to establish the effect of the preliminary mechanical activation of phosphates on the degree of phosphorus extraction by bioconversion of Bulgarian and Tunisian phosphates using A. niger fungi and T: thiooxidans microorganisms. The influence of the phosphate concentrations, the type of the nutritive medium and the incubation times on the process of biological mobilization of the phosphates was studied. When the concentration of phosphates in the medium is twice as high, an equal and/or higher degree of phosphorus extraction can be achieved through the bioconversion of mechanically activated phosphates compared with non- activated phosphates under similar conditions. A maximum degree of 90+% phosphorus extraction in utilizable form was achieved at definite conditions.

Jan 1, 2002

By J. C. Heter

Industrial Mineral Fillers, LLC. is in the initial stages of mining and processing Anorthosite (CASPAR TM) at its CASPAR mine located in Soledad Canyon, Los Angeles County, California The CASPAR is being mined from the Precambrian San Gabriel Anorthosite Complex of the western San Gabriel Mountains. Preliminary results suggest that CASPAR is a desirable alternative to silica sand used in construction applications, such as, stucco, grout, abrasives, and other uses including filtration and golf course recreation sands. With the use of standard ore dressing techniques, CASPAR is suitable for use as a filler in paint, plastics and rubber. Environmentally, CASPAR has advantages over silica sand, in that, there is no detectable Free Silca.

Jan 1, 1997

By Raúl Castro, Marco Vera, Alfonso Ovalle

The underground mining evolution for block cave mines in Chile and worldwide has made important strides in the last decades. Nonetheless, reserves determination in the initial stages of these types of projects—mainly for long-term planning—is not studied in as much detail as it should be, especially regarding the impact on the final value of the enterprise. Today, the first estimation of the size of a block cave mine, typically expressed in tons, tends to determine very large footprints and ore bodies. The resulting large-scale mine is obtained by applying the marginal cut-off grade (COG) to determine reserves. Yet, in many cases, it is possible to obtain an equal or higher benefit, extracting fewer reserves in less time, with a smaller active area, which significantly reduces the project’s uncertainty. To explore scenarios obtained by applying a higher marginal COG in the initial phases of the project, the Hill of Value methodology is used to estimate the net present value (NPV) in relation to the production rate and the COG. However, the application of this methodology considers certain simplifications that generate results which are not completely satisfactory in specific cases. This paper suggests an improvement of this method to obtain more reliable results regarding determination of a COG profile that will optimize the NPVof a block-cave project. The methodology was developed and applied in a massive polymetallic deposit with zinc, lead, and silver mineralization, corresponding to a real block caving project. The methodology provides NPV results that differ by approximately 15% in comparison to the real mine plan, while also being considerably simpler and faster to calculate. In summary, the proposed methodology provides a reasonable and fast procedure to estimate higher than marginal COG that increases the NPV of block cave mine projects.

By Yingbao Yang, Jinyue Liu, Yonggang Wei, Bo Li

Due to the depletion of copper ore with high-grade and low impurity contents, the raw materials for copper smelting exhibit low copper contents and high impurities. High-impurity elements lead to the poor performance of the final copper product; thus, the removal of impurity elements during the oxygen-enriched copper smelting process is crucial. In this study, based on the production of high-grade matte, the occurrence states of impurity elements (such as As, Pb, and Zn) are analyzed in the input and output materials of the oxygen-enriched smelting process, and the phase transformation mechanisms of impurity elements are revealed during the oxygen-enriched smelting process. The effects of temperature, Fe/SiO2 ratio and oxygen concentration on the distribution behaviors of impurity elements in dust, slag and matte and the removal rates of impurity elements in matte are clarified. The results show that the impurity elements mainly exist as As4, As4S4, As2O3, Pb, PbS, PbO, Zn and ZnS in dust, as FeAsO4, As2O3, FeAsS, PbSiO3, Zn2SiO4 and ZnFe2O4 in slag, and as As, FeAsS, PbS, PbO and ZnS in matte. High smelting temperature, low Fe/SiO2 ratio and low oxygen concentration are beneficial for improving the matte grade and the removal rates of impurity elements Pb and Zn in matte. Low smelting temperature, low Fe/SiO2 ratio and high oxygen concentration are beneficial for removing impurity element As in matte.

Aug 8, 2023

By David Brown, Glen Hall, Ken DeVos, Frank Barone

Dredging and Flooding was completed on the Falconbridge Limited "New Tailings Area" in the period from 1996 through 1998, as part of their site closure measures. Part of the decision making process and closure planning was water quality prediction, including oxidation and diffusion modelling. The purpose of this modeling was to define the potential water quality that would result during and after dredging. A significant body of research on the geochemistry and oxidation kinetics of this site had been compiled. The results of the modeling provide practical insight on the potential water quality that may be expected. Water quality in the pond has steadily improved since flooding was completed with the exception of short term peaks during spring runoff. Aquatic vegetation is appearing through natural recovery and transplanting of local species, and colonies of minnows are now observed in the ponds.

Jan 1, 2000

By D. W. Fuerstenau

One of the more energy-efficient methods for size reduction, namely particle-bed comminution under high compressive loads, was employed to grind eight minerals and ores, using up to 250 MPa pressure. A new approach based on the self-preserving character of the ground product size distributions and a linear energy-reduction ratio relationship is proposed for analyzing this mode of size reduction. The grind ability of the material when comminuted in a particle bed is about one-half that of the single-particle crushing mode, which is in agreement with previous estimates of the relative efficiencies of energy utilization based on direct measurements of surface area produced. The loss of efficiency may be attributed to energy dissipation by particle interaction phenomena in compressed beds.

Jan 1, 1993

By Jean-Luc Cornet

As modern conveyors are increasing in size and complexity, their control requirements are becoming more and more critical. In addition to the safety and equipment protection requirements, control systems are now called to implement intelligent drive controls derived from dynamic analysis modelling, as well as to provide fast and accurate diagnostics while keeping operator controls simple. These requirements led to the development of a new and innovative approach to control system development. This paper describes the control philosophy used by Conveyor Dynamics, Inc. (CDI) and some of the key features of our approach to the architecture of control systems.

Jan 1, 1993

By K. E. Hjelmstad

Solution mining operations often encounter difficulty maintaining adequate leach solution flow into the ore formation because of loss of formation permeability near the injection well. Permeability loss caused by swelling and breakup of clays and fine particle migration can often be the cause of the problem. Combined permeability and leaching tests were done in the laboratory on samples of clay bearing ores to evaluate a clay-stabilizing polymer's effectiveness in preventing the problem. Test results indicate that treating the ores with cationic polymers could maintain permeabilities two to five times greater than the long-term permeabilities present in untreated ores. Both alkaline (pH 8.5) and acidic (pH 2.0) leaches were used in the permeability leaching tests. To determine the reasons for the success of the clay stabilizing polymer, clay swelling tests and zeta potential measurements were made on untreated ore samples and on ore samples treated with the cationic polymer. Test results indicate the cationic polymer could reduce the degree of negative charge on fine particles and their tendency to disperse, as well as reduce clay swelling. Test results indicate a potentially beneficial effect on operating parameters such as capacity and injection pressure during leaching, if clays and fines are kept stabilized. This may be done by treating the zone of high fluid velocity near injection wells with cationic polymers.

Jan 1, 1991

By Terry Ritzel

Predictive maintenance technologies include vibration analysis, tribology, infrared thermography, ultrasonic detection and electrical measurements. These technologies have been applied to large electric mining shovels at the Cyprus Sierrita Mine outside of Tucson, AZ. The predictive maintenance program was initiated on the P&H models 2300 and 4100 electric shovels during August 1996. Results of these technologies have shown the potential for improving electric min- ing shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition-based planning of component replacement. Maintenance costs are minimized by focusing resources through condition-based prioritization.

Jan 1, 1997