Search Documents

By Bhaskar B. Thapa

The proposed Caldecott fourth bore will consist of a two lane highway tunnel along California State Route 24 near the City of Oakland. The proposed design and construction sequence for the 15-m-diameter tunnel are based on the New Austrian Tunneling Method (NATM). The initial support system incorporates combinations of shotcrete, rock dowels, lattice girders, spiles, and grouted steel pipe canopies. The final lining is cast-in-place reinforced concrete. A waterproofing membrane and drainage system are placed between the initial and final linings. State Route 24 is a lifeline route, required to be open to emergency vehicles within 72 hours after a major earthquake, defined as having a return period of 1,500 years and a peak ground acceleration of 1.2 g. Although the seismic design criteria are stringent, the design of the tunnel lining system is ultimately controlled by static ground loads in the weak rock along the alignment.

Jan 1, 2008

By John F. Abel

Convergence measurement across the 17.4 m (57ft) high shaft station/loading pocket at Mt. Taylor provided continuing verification of stability and safety. Three levels of instrumentation, consisting of three lines each, were installed and monitored. The instrumentation showed that the flexible lining restrained the adjacent rock. The flexible lining consisted of pea gravel with neat cement between rock and liner plate, wooden crush blocks between liner plate and steel ring beams. The loading pocket is elliptical, 11.6 by 9.6 m (38 by 31 1/2 ft) I.D. The crush blocks were designed to allow 15 cm (6 in.) of convergence. Maximum predicted convergence was 7.0 cm (2 3/4 in.) and 5.7 cm (2 1/4 in.) was measured. Convergence measurements also demonstrated decreasing deformation with respect to elapsed time and distance from the measurement station to the temporary bottom of the shaft excavation.

Jan 1, 1984

By V. K. Kollipara

Air flow patterns in the face area of a room-and-pillar mining are critical for understanding the dust dispersion characteristics and for developing engineering controls. SIUC has previously performed a CFD study to analyze the airflow patterns in the face area when continuous miner is making a straight cut. Results from this study identified low air velocity and re-circulation zones in the face area and illustrated the significance of line curtain, and scrubber operation on the air flow patterns. This paper discusses similar analyses when continuous miner is making a right turn cut as it is considered to be the dustiest cut among all the cuts made to advance an entry through a crosscut. This paper presents results for box-cut development for a right hand turn x-cut. This paper also addresses line curtain advance and air leakage through the curtain on the airflow patterns in the face area for such a cut. Low air velocity and recirculation zones were identified by analyzing the velocity vectors.

Jan 1, 2012

By B. Spigarelli

Carbon dioxide sequestration by conversion to carbonates has become a promising option for CO2 storage. Experiments were conducted to determine the feasibility of CO2 sequestration at ambient conditions using a Ca-rich industrial waste in a carbonate solution. The Ca-rich industrial waste used in this study was lignite fly ash. Fly ash was chosen because it is cheap, available near large CO2 point sources, already in powder form, and reactive due to amorphous properties. In the experimental set-up, CO2 absorption was inferred by monitoring feed and exhaust gas CO2 concentrations. The addition of an alkali to a fly ash-distilled water solution provided a 50% increase in CO2 absorption of the solution. Absorption time also increased by 50% compared to a fly ash-distilled water solution. TGA analysis was used to determine the extent of CO2 sequestration in the carbonate form. At a liquid to solid ratio of 20:1, the conversion of ?free? calcium to carbonates was 75%. A CO2 balance on the system concluded that at the current operating conditions 42% of the total CO2 fed to the system was sequestered in the carbonate form. SEM-EDS analysis of the fly ash particles before and after reaction with CO2 indicated that the carbonate compound being formed was calcium carbonate. The analysis identified rhomboidal structures on the surface of the fly ash particles after reaction with CO2, but not before. These rhomboids are characteristic of calcium carbonate formation and they had higher Ca, C, and O concentrations than the host spheres, suggesting calcium carbonate formation.

Jan 1, 2012

By D. Drymonitis, G. Gialoglou

"Placer gold mineralizations have been observed in the north-eastern parts of Greece. Some of them have been at first evaluated to be of special interest so, exploration campaigns have been designed and carried out. Among the other exploration techniques applied on the sites of interest, drilling was the one to give the detailed information and data for the evaluation of the deposits. Having collected the data from trenching and two consecutive drilling campaigns, they were processed geostatistically to estimate the ore reserves and therefore the economic interest of the deposits. The latter was done by using exploitability indices, which would give a rough idea whether the deposits were economically feasible. A small number of such deposits have been spotted in the area and have been explored and evaluated as above. The present paper deals with the most important of them, giving all the process followed and the results derived from the exploration carried out."

Jan 1, 2005

By S. Ersayin

In 1998, the Concentrator Modeling Center was established within the Coleraine Minerals Research Lab, Coleraine, Minnesota, to develop models for simulation of iron ore processing plants, and to assist plant operators in improving performance of their aging plants. The short-term objective was to develop necessary models for reliable simulation using conventional techniques, while the long-term objective was set as liberation-based modeling and simulation of these plants. The short-term objective was achieved in 2002 after the development of models for magnetic separators, hydro-separators and fine screens. A project funded by the U.S. Department of Energy was carried out to demonstrate the capability in improving iron ore processing at the Minorca plant. As a result of this study, a 10% improvement in throughput at the plant was obtained, and simulation became a desired tool for plant operators. A significant step in the long-term objective was reached in 2005 with the development of a liberation model. This was followed by incorporation of models capable of processing liberation data into the software. By early 2007, the Concentrator Modeling Center had the capability of performing liberation-based simulation of entire plants.

Jan 1, 2009

By Hiroshi Yamazaki

The paper describes prediction, control and validation of face pressures, and special TBM features for the bored tunnels of the New Metro Rail City Project, Perth, Australia. The selected EPB-TBM passed below a heritage bridge and the operational Perth Railway station in ground conditions consisting of fully saturated uniform sand combined with shallow overburden and a horizontal alignment radius of only 135m. Therefore, strict control of volume loss, TBM operations and ground movements was vital requiring continuous evaluation and adjustments to TBM operation parameters. The paper discusses the effectiveness of applied TBM face pressures and the used foam/polymer soil conditioning which was measured against achieved volume loss and the predicted range of ground settlements.

By Scott Ellenbecker

Soon New York City will have a new train station. A tunnel project is under construction to extend Line 7 to a new station that is located near the Jacob K. Javits Con-vention Center. This is also part of the Hudson Yards redevelopment project that is intended to aid redevelop-ment of the west side of Midtown Manhattan around the Long Island Railroad?s Caemmerer Railyard. The station, or ?cavern? as it?s called by those excavating it, will be the portal for that growth. In the city, public transportation means high-rise residential proper-ties will have better access to the business district, and those outside the area will have greater access to event facilities ? two factors that are critical for development investment.

Jan 3, 2010

By P. Rambalee

A multiple coal fired boiler house provides steam for utility usage in various production plants. Maintaining stable header pressure and boiler availability is of critical importance for downstream consumers. Advanced Process Control comprising of a G2 based expert system and Model Predictive Control was implemented to improve the boiler house performance. The results yielded improvements in the main header pressure stability, reduction in boiler saturation and significant saving in coal consumption. All information used for this document is from a published whitepaper written and led by Prevlen Rambalee (Anglo Platinum) and Gustaf Gous (BluESP) titled, ?Control and Stabilization of a Multiple Boiler Plant: An APC Approach?.

Jan 1, 2012

By L. K. Marshall

Last month's engineering fundamentals article discussed some general considerations of underground mine ventilation. This month's article takes a look at auxiliary ventilation-brattice, fans, and ducting-in underground mines. The need for good, efficient auxiliary ventilation increases as mines get deeper and move farther from ventilation shafts. New mining methods and equipment resulted in faster work area advances, liberating more dust, gas, and heat. As a result, worker health and safety requirements in the face area have become more stringent. For all these reasons the safety and efficiency of any underground mine depends heavily on its auxiliary ventilation. The purpose of such ventilation is to supply sufficient quantities of clean air to the face of the drift and to maintain air quality within desired limits until expelled from the mine.

Jan 2, 1982

By Jacques F. Abrahamse, Kevin A. Bahe, T. Arthur Palm, Gregory E. McCluskey, Stephen L. Bessinger

Introduction Basis For System San Juan Coal Company (SJCC) is a subsidiary of BHP Billiton. Until recently, BHP Billiton operated three surface mines in northwestern New Mexico: Navajo, San Juan, and La Plata. The San Juan and La Plata Mines supplied the San Juan Generating Station operated by Public Service of New Mexico. Stripping ratios at those operations were increasing, and by 2000 a feasibility study was underway to develop SJCC’s vast underground reserves as a replacement. Early in the evaluation and planning phase for the San Juan Underground Mine, it was determined that the target seams (Fruitland #8 and #9) had a high propensity for spontaneous combustion. Spontaneous combustion was identified as a risk, both to personnel and equipment, and to the ability of SJCC to reliably fulfill its obligation to the power plant. In the last 20 years, several western US coal mines suffered underground spontaneous combustion events and/or mine fires. Included in this group were Colorado Westmoreland’s Orchard Valley Mine (1987), RAG’s Willow Creek Mine (1998 and 2000), Oxbow’s Sanborn Creek Mine (1999), the West Elk Mine of Arch Coal (2000), Arch’s Skyline Mine (2002), Western Fuels’ Deserado Mine (1996), and the West Ridge Mine of Andalex Resources (2003). The cause for the majority of these fires was spontaneous combustion. Fighting the fires required injection of an inert gas or foam. Nitrogen and carbon dioxide were the predominant choices of inert gas. In all cases, the gasses had to be trucked in from considerable distances. Before the inert gas could be used, injection holes had to be drilled into or near the suspected fire locations. This drilling and trucking caused costly delays in the timing of the fire fighting effort, and was not as precise as desirable. Emergency purchasing of gas and pumping services was extremely expensive, running as high as $70,000 per day at one mine. As a result of the experience of other western US coal operators, and the risk inherent with spontaneous combustion at SJCC, it was decided to pursue installation of a nitrogen delivery facility on-site at SJCC. This decision was later expanded to include a continuous supply of nitrogen.

Jan 1, 2005

By Kenneth W. Torpey, James G. Ball, Richard F. Flanagan, David S. McAllister

INTRODUCTION Under a Federal grant by the Urban Mass Transit Administration (UMTA) (80%), and sponsored by the State of New York (200), Niagara Frontier Transportation Authority is constructing a 10.3 km (6.4 mile) light rail rapid transit system in Buffalo, New York. The $450 million project, which began construction in the Spring of 1979, is unique in rail transit alignment designs in the U.S.A. and the first predominantly underground light rail system in North America. The Buffalo project is unique in that the first phase of the expandable system follows the alignment of Main Street and is on the surface in a proposed 1.6 km (1.0 mile) pedestrian mall in the downtown business district. The alignment then progresses northward into a cut-and-cover portal and standard double-box configuration for 2.74 km (1.7 miles) at a depth of 9.1-10.7 m (30-35 ft) and subsequently drops into bedrock at depths of 18.3-27.4 m (60 to 90 ft). The 5.63 km (3.5 mile) rock tunnel section consists of two single tunnels 4.88 m (16.0 ft) nominal finished diam. and includes five stations. The rock tunnel line section was divided into a north and south contract of 2 316 m (7,600 ft) and 3 243 m (10,640 ft), respectively. Due to the existing surface facilities and the future station locations, the line tunnel contracts differed considerably in their shaft access

Jan 1, 1981

A practical core-based method for estimating in situ stress was tested using 360° measurements of rock core diameter in a laboratory setting. In several mining districts across West Virginia, rock cores were recovered from exploration core holes and oriented using an acoustic televiewer (ATV) summary log. Measurements of diametral variation were performed at 0.1-foot depth intervals using a benchtop device comprised of a pair of diametrically opposed contact digital indicator gauges working in tandem. The diametral profiles were evaluated to determine strain direction and strain magnitude. Stress magnitudes were calculated when values for Young’s modulus, and Poisson’s ratio were available. Stress direction results are compared to other stress determination methods, including downhole overcores, drilling-induced fractures, and borehole breakouts. The testing and analytical methods used are similar to the diametrical core deformation analysis (DCDA) method (Ito, Funato, and Shono, 2012), but with a number of important improvements.

Jan 7, 2020

By Felix E. Mutschler

Alkaline rock-related precious metal deposits include: • orthomagmatic platinum group elements (PGE) ± gold (Au); • porphyry copper-silver-gold (Cu-Ag-Au, ±PGE); • epithermal Au-only, and Au-Ag-base metals; • submarine exhalative Kuroko-, Cyprus-, seamount- and Yellowjacket-type deposits; and • enigmatic deposits akin to Olympic Dam. Coeval epithermal deposits related to porphyry deposits suggest the two types represent separate immiscible fluids evolved in oxidized, CO2-rich alkaline magma chambers. Alkaline rock provinces develop above mantle hot-spots, but crustal structures control the final distribution of magmas and ore fluids. Prospecting guides for alkaline rock-related precious metal deposits include the presence of evolved alkaline rocks, pervasive K-metasomatic, redox and carbonatic alteration and low level Au (±Te, etc.) anomalies. Although alkaline igneous rocks crop out in less than 1 % of the area of the North American Cordillera and craton, alkaline rock-related ore deposits have produced nearly 13% of the total United States and Canadian lode gold production. Large (31-t or 1 million-oz) deposits are common (Fig. 1), and additional deposits and reserves are being discovered. New genetic models are evolving, making alkaline rock-related precious metal prospects attractive exploration targets.

Jan 1, 1991

By M. R. Shahan, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3000 cfm (1.42 m3 /s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3 /s).

By R. Pothina

The objective of this research was to develop a mathematical model for gyratory crushers to help in the prediction of energy consumption and to analyze dominant parameters that affect this energy consumption. The development of a gyratory crusher model was achieved in the following three main stages: mathematical representation and coding of the crushing process; building an amperage constant model to derive an energy-scaling formula; and modifying the amperage constant model to represent a full-scale model. Due to their significant influence on feed-size distributions, two blasting parameters, i.e., burden and spacing, were considered. The crusher parameters that affect energy consumption were also identified. A case study of an operating dolomite mine was performed. The results indicated that by changing the burden, spacing and crusher closed-side setting, the overall (blasting and crushing) costs could be reduced by 4.7% to 7.9% annually. It can also be concluded that burden and spacing values have a linear positive relationship with the crusher energy consumption, while closed-side setting values have an inverse linear relationship with the energy consumption.

Jan 1, 2007

By Adam H. Zimmerman

Introduction Noranda, like similar businesses, is suffering the pain of previously unheard of currency relationships, a cost structure built in better days, and conditions of gross oversupply possible in almost any commodity. Indeed, it does seem like the worst of all possible worlds is out there before us. To understand a Canadian natural resource company, you must know how the country is organized. So far as natural resources are concerned, Canada is not Canada. Canada is 10 provinces and each own the resources situated therein. Thus, the conditions of extraction, exploitation, and operation are all set by the province, while the conditions of trade and currency are set by the Federal government. This means that what may be the rule in Newfoundland may not be the rule in Manitoba or British Columbia. The second thing is that the Canadian currency has been a satellite of the US dollar for a long time. This means that we hold the unenviable and unjustified position of being the country with the second strongest currency in the world. What this has meant to us is what it has meant to an American operator. Since 1980, a pound of copper fetches 214% more for a Chilean than it does for us and a pound of zinc 115% more for a Belgian. From an American point of view, Canada is favored because its dollar is valued at 25% to 30% less than the U.S. However, because of industrial indiscretions in years past, Canada has a locked in labor cost disadvantage that is very hard to cope with. Canada has a unique situation with its labor unions. Many of the unions are, or have been, internationals and therefore gained undue strength in early days. Canada has a third political party of socialist persuasion. It is entirely funded by dues from laor union members. Thus, we have a politicized workforce. And finally, we have a public service that has the right to strike. This had made the public service unions by far the strongest now in Canada. What this means to the mining industry is that there is somebody out there blazing the trail. The unrelenting power of these public service unions probably creates a climate more conducive to excessive wage settlements in industry than would otherwise be the case. Study, Work, and Pray So what do we do when times get tough? In simple terms, we study a lot, we work harder, and we pray a great deal. We study a lot in terms of learning hitherto unknown strengths and weaknesses of our products, processes, and operations. We work hard in the sense that we do everything possible to improve our productivity. And we pray a lot because, so far, anything else we have done has not been enough. Some years ago, Noranda recognized that its principal base and precious metal operations were diminishing. To provide for the future, we should branch out into other resource type operations. These might be countercyclical and also perhaps a little more permanent. For this reason, Noranda entered the potash, aluminum, and forest products businesses. This, of course, was a 'brilliant' strategy that was much applauded in its early days. We built an excellent potash mine, the smallest inte-

Jan 6, 1985

By R. Hardy

LaModel is a boundary-element program capable of calculating the displacements and stresses in thin bedded deposits such as coal, salt, or potash. Throughout its history, it has continually been upgraded in order to expand analysis detail and stay current with the latest advances in computer technology. The most recent enhancements include: an increased grid size capability, a significant increase in the speed of the automatic grid generation using an AutoCAD visual interface, implementation of subsidence-based horizontal strain calculations for multiple-seam situations, and pillar safety factor calculations. To demonstrate these new features, a multiple-seam case study of a longwall panel undermining an active set of main entries is presented.

Jan 1, 2006

By M. Slatter

The need for anti-corrosion coatings has existed for many years in the ground support industry, but the application requirements have made coating selection limited. Varying groundwater and chemical conditions continually challenge long term coating performance. Traditionally the industry coating preference has been hot-dip galvanizing due to its performance characteristics in highly corrosive environments and low cost nature. However, the galvanized coating has application limitations. This paper highlights some of these limitations and provides selection criteria for a new organic coating developed for one such difficult application, DSI?s Omega BoltPTM Pwhich is an expandable ground support. [ ]

Jan 1, 2009

By J. C. Yingling, R. J. Sweigard, P. W. Conrad, J. M. Ringe, D. H. Graves

Much of the land reclaimed since enactment of the 1977 Surface Mining Control and Reclamation Act is over-compacted. Research has shown that excessive compaction in replaced growing media is detrimental to establishment of trees. If trees are to be grown on reclaimed surface mined sites, something must be done to alleviate this excessive compaction. Dry bulk density and penetration resistance are two soil parameters that can be used to indicate the level of compaction in reclaimed growing media. The University of Kentucky has developed test cells on reclaimed sites at a surface mine in eastern Kentucky to determine the impact of tillage (ripping) on soil compaction and tree survival rate. The ripping methods being evaluated include shallow tillage using conventional farm equipment and deep tillage using a dozer with a ripping arm. The impact of organic soil supplements on soil physical properties and tree survival rates is also being evaluated at the site. The organic soil supplements being evaluated include application of hardwood bark and application of straw and mulch. Each test cell has been planted with various species of trees, and for the first two years, data have been collected at these test cells for soil dry bulk density, penetration depth and resistance, and survival rate of trees. These data are currently being correlated to determine how ripping and the application of organic soil supplements affects the relationship between soil compaction and tree survival rate.

Jan 1, 2002