Search Documents

By M. J. Sapko

The Bureau conducted, through joint funding with the Colorado Mining Association, large scale oil shale rubble fire tests to investigate flotability characteristics and different methods of extinguishment. Ignition of large rubble piles was easily accomplished. Foam blankets could be used to control surface flames. The results of these large scale tests confirmed that water was effective in extinguishing deep seated oil shale fires but not particularly efficient. It took up to 1.7 times as much water to extinguish a fire as anticipated on the basis of a simple cooling model, assuming 100 pet utilization.

Jan 1, 1989

By V. K. Karra

Research by various workers has shown compressive comminution to be significantly more efficient than impact comminution. Based on the work being done at Nordberg, wet compressive crushing in cone crushers producing finer and finer products, shows the feasibility for partial substitution of conventional tumbling mills. For further substitution, major challenges are processing of fine feed slurries in cone crushers to realize a significant size reduction of the particles, and understanding the limitation of the gyratory type units in terms of finest product achievable. The paper addresses the challenges involved, efforts at Nordberg, and the implications to conventional comminution flowsheets.

Jan 1, 1989

By J. M. Manka

American mining companies operate many drum hoists, hoisting from varying depths with varying payloads. This paper reviews the procedure for selecting optimum wire rope constructions for existing hoisting installations. Selection for proposed installations, along with recommended hoisting parameters, is also discussed. To achieve optimum rope performance, preventive and corrective maintenance procedures are required and are reviewed here, along with examples of rope problems and their causes.

Jan 1, 1993

By Guido Deissnann, Jennifer L. Kirkaldy, Stephan Kistinger, Carol M. Pettit

Contaminated mine drainage presents a potential hazard for aquatic ecosystems and groundwater resources. Reliable predictions of long-term developments in seepage quality are necessary to select reasonable decommissioning options and remediation measures for waste-rock heaps during mine closure and/or mining site rehabilitation to minimize future risks and environmental hazards. Extensive geochemical modeling work was used to assess the consequences of various remediation options for waste rock heaps at a former uranium mine in Eastern Germany. The predicted contaminant discharges are used for an assessment of long- term benefits of decommissioning alternatives to derive conclusions for sustainable remediation measures using risk-based cost/benefit analyses.

Jan 1, 2000

A series of laboratory based push and pull tests were carried out to investigate how surface profile influence the load transfer mechanism of bolt/resin interface. Tests were carried out in both 75 mm and 150 mm long steel sleeves. Three types of bolts were examined, they were bolts most commonly used for strata reinforcements in underground coal mines in Australia. The bolts had near equal core diameter but of different profile configurations. The change in the length of the encapsulation sleeve was examined in light of the small number of profiles encapsulated effectively in short 75 mm long sleeves. The results showed that peak loads and displacements were directly related to the height and the spacing of the bolt surface profiles. Profile spacing appears to have greater influence on load transfer capacity than the profile height.

Jan 1, 2006

By Matthew J. Hrebar

Dragline stripping operations account for over one-half of the U.S. bituminous coal production mined by surface coal mining methods. The dragline is a popular stripping tool because of its flexibility in varying overburden depths and relatively low operating costs per cubic yard of overburden. Because of the relatively high capital costs of the machines and their use as a primary stripping tool, the selection process is an important step in the mine planning procedure.

Jan 1, 1979

By G. Bourque

Early in the design stage of their new concentrator for the Mount Wright Plant, Quebec Cartier Mining decided to use a process computer for total control of crushing, grinding and concentrating. A map of the area is given in figure 1 and a view of the plant in figure 2. Although the use of process computers is not a new idea in petrochemical and chemical industries, their use in the mining industry is very limited. We innovated in using the computer, not only for data logging, as we have seen in some other plants, but a sole operator located in the administration building, starts and stops mill lines, crushers, load-out system, tailings, thickeners, etc ... by means of a CRT console. Our process is fairly simple as can be seen on the schematic process flow diagram (figure 3). .The ore, carried by 136t diesel electric trucks, is dumped through ore pockets onto two primary pan feeders. The feeders supply two 1,52mx2,79m gyratory crushers which reduce the ore to minus 20,32 cm. Each crushing line have a capacity of 5600t per hour and feed a shuttle conveyor distributing the crude ore into six silos.

Jan 1, 1979

By Yousef Ghorbani, Abolfazl Danesh, Fatemeh Kazemi, Ataallah Bahrami, Morteza Abdollahi

The abstract highlights the impact of flocculants used in the middle thickener of a copper-molybdenum plant on both process water quality and molybdenite floatability. The study investigates the effect of a starch-based flocculant (wheat starch) on the efficiency of the middle thickener and molybdenite flotation. The findings indicate that the presence of starch influences the settling behavior of particles with different shapes, and the dosage of starch affects both molybdenum recovery and the presence of copper minerals in the molybdenum concentrate.

Mar 7, 2022

By V. J. Kecojevic, W. A. Wilkinson

Mining companies are increasingly looking at Global Positioning System (GPS) technology coupled with 3D mine planning and visualization systems to deliver increased productivity and reduction in operating costs in drilling and blasting operations. Leveraging GPS into drill and blast operations requires that a drilling plan be developed and imported into the GPS to guide the operation to a planned and desirable outcome. State-of-the-art mine planning software systems provide the engineer with a 3D environment in which to design and visualize drill and blast plans. This paper discusses producing and exporting 3D drill and blast plans to GPS and how some coal companies are utilizing GPS and mine planning software technology in the drill and blast process.

Jan 1, 2004

By Christopher Haycocks

Successful ground control is an essential part of all viable underground mining operations. To a large extent ground conditions influence the choice of mining methods, percentage and cost of extraction, and often the degree of safety that can be achieved. Utilizing the computer for ground-control planning offers great potential under many diverse conditions as not only are computations facilitated, but also details of the often complex geologic and structural framework of the mine can be readily stored and retrieved. Two basic approaches have been developed for applying the computer in solving ground-control problems. The first uses an analytical method, such as the finite element technique, for solving a specific problem. The second is more general and involves storage of geologic data and application of general design equations. The latter has found wide application in stratified deposits. It is the purpose of this chapter to describe both approaches as they are used for improving the ground-control aspects of mine planning.

Jan 1, 1979

By P. D. Roa, O. Noirot, H. Owens, D. E. Walsh, J. R. Mokka

Over a period of eight years (1989 through 1997) the Mineral Industry Research Laboratory (MIRL) at the University of Alaska, Fairbanks, AK, has investigated the effects of temperature, residence time and particle size on the degree of low-rank coal (LRC) upgrading for a nonevaporative, hydrothermal drying process, also known as hot water drying (HWD). The following three Alaskan LRCs were used in this study: Usibelli coal (Seam No. 4) from the Nenana Coal Field, Little Tonzona coal from near McGrath, and Beluga coal from the Beluga-Yentna field on the west side of Cook Inlet. Replicated factorial tests were conducted. Experimental results indicate that most of the low-rank coal upgrading via HWD occurs rapidly within the first 10 to 20 min of residence time. Thereafter, the upgrading process slows down, and more than 100 min of additional residence time is required to produce percentage increases equivalent to what was achieved in the first 10 to 20 min. The properties of the hot water dried products were very sensitive to process temperature. Calorific value, carbon and oxygen contents, equilibrium moisture levels and Hardgrove gindabilities all appear to change linearly with temperature within the 275°C to 325°C (525°F to 61 5 OF) range.

Jan 1, 2000

By KAGAN BENZESIK, OMUR CAN ODABAS, SELCUK KAN, Onuralp Yucel

In this study, domestic molybdenum disulfide (MoS2) concentrate was roasted in a chamber furnace and then in a rotary kiln. The behavior of the roasting process was examined in both furnaces, and which type of furnace is more advantageous to use in mass production was investigated. It is theoretically possible to roast in a chamber furnace, but a major problem was observed when the amount of concentrate was increased in the chamber-furnace experiments. The problem was solved by using a rotary kiln. This study improves the understanding of the roasting of  MoS2 concentrate and presents a different perspective to the industry, showing that rotary kilns can also be used for roasting.

By Alex Harrison, Steve Kasper

Various countries around the world have testing and manufacturing standards in place for steel cord belting. These standards are very comprehensive in what they allow the end user to specify, however, their practical significance in terms of belt life is more difficult to quantify. Such testing standards will be briefly reviewed in this paper in relation to the implication for end user expectancy. Since there is no US standard of manufacture, the end user is left with writing their own specifications. In addition, such standards do not address the effect on belt life of manufacturing faults, such as cord plane buckles, or lateral cord movement. Some new technology used to test steel cord belting will be described as an aid to both manufacturer and end user. Specific end user related issues addressed on this paper are: Tracking and belt quality Cord plane irregularities and performance Cord size and belt life Cord fatigue and testing

Jan 1, 1993

By R. W. Reisinger

An historic underground copper mine in Wyoming is discharging neutral but copper-laden water into a pristine creek. The EPA-deferred site qualifies for reclamation by the Wyoming Abandoned Mine Land (AML) program; restoring the discharge so that the creek can eventually support a trout fishery is the cleanup goal. Hydrological and geochemical investigations underground have suggested two sources of mine water: one clean and the other copper-containing. Results of bench-scale and pilot-scale tests support the viability of using low-cost passive treatment techniques to reduce copper concentrations in the near-freezing mine discharge.

Jan 1, 1998

By S. K. Kawatra

In order to meet federal air pollution guidelines, it is necessary to remove a considerable quantity of sulfur from many North American coals. This may be accomplished by oxidizing the sulfur to water soluble forms, followed by washing the coal. Selective oxidation of the various sulfur forms can be accomplished through the use of a variety of types of bacteria. In this paper, the various bacteria and their requirements are described, and processes using bacteria to remove coal sulfur are discussed.

Jan 1, 1987

By H. E. Epstein, B. K. Parekh, W. M. Goldberger

Comminution is the single most expensive operation in mineral processing. It consumes about 50% of the energy required for mineral extraction (Agar, 1976). Current comminution technology is both energy-intensive and inefficient. A novel noncontact comminution process concept was developed in this study, whereby selective lib¬eration of minerals from an ore could be potentially achieved. The process involves application of electric and ultrasonic energy to liberate minerals from gangue particles. Introduction The mineral industry is a large user of energy in the US. Energy usage is increasing as the grade of ores processed decreases. It is es¬timated that comminution of ores uses about 32 000 kWh (115 trillion kJ), or 2% of the electric power produced in the US (NMAB-365, 1981). Among other minerals, ce¬ment, iron, and copper processing plants are the largest users of en¬ergy in comminution. Very little of this energy used in conventional grinding (about 1%) is used to gen¬erate new surface. The remainder is wasted (Table 1). Thus, there are substantial energy-saving and economic incentives to improve the efficiency of crushing and grinding techniques for mineral recovery. With an energy efficiency of only 1%, it would seem possible to devise methods to significantly improve comminution technology. This requires that breakage force be applied only where needed, not indiscriminately as in a conven¬tional ball mill (NMAB-365, 1981). Can apparatus and methods be de¬ veloped for large-scale commer¬cial use that allow energy to be fo¬cused at intergranular bounda¬ries? If this can be done, mono¬mineral grains would remain in¬tact and the grinding action would be selective and substantially more efficient. The novel comminution process concept described in this paper uses a combination of electric and ultrasonic energy. This energy breaks the ore and selectively lib¬erates minerals. The process has also been termed a two-stage or electroacoustical comminution process (Goldberger, Epstein, and Parekh, 1982). The mineral grain boundary is usually the weakest area in an ore. By applying electri¬cal energy to the ore, the rock frac¬tures mostly at grain boundaries. At the same time, the electric shock creates secondary hairline fractures in the ore. Additional application of ultrasonic energy to this ore provides further break¬age. The concept was proven on a molybdenum porphyry ore but needs additional study. Technical Background There have been substantial im¬provements in milling machinery and grinding operations, but rela¬tively few attempts have been made to develop alternatives to conventional impact milling. Sev¬eral methods, however, have been investigated that relate to this study. In the early 1970s there was considerable interest in a size re¬duction method known as the Snyder Process (Cavanaugh, 1972). It involved charging coarse ore into a pressure chamber, pressur¬izing with a gas, and activating a quick-opening (15 msec ) dis¬charge valve that connected the chamber to a discharge duct. This allowed solids to fluidize and ac¬celerate, subjecting the material to a variety of impulse phenomena that caused the desired size reduction. Other nonimpact means of achieving breakage and selective size reduction have been de¬scribed in technical and patent literature. Kanellopoulos and Ball (1975) considered using heat to induce thermal stress in quartz¬ite. This would cause cracking and, thus, increase grinding efficiency. The use of electrical energy to induce thermal stress was studied by the General Elec¬tric Co., in cooperation with the Montana School of Mines, under a research grant from the Anaconda

Jan 9, 1984

By C. W. Armbrust

At FHC Gold Company's Paradise Peak Mine gold and silver are produced. Precious metals recovery rates are very satisfactory along with the recovery and production of a relative high volume of mercury. At Paradise Peak precious metals are recovered via the Merrill-Crowe process and delivered to the refinery area as a mercury-bearing precipitate cake. The recovery of mercury is then obtained through a vacuum retort system. The balance of the material is mixed with fluxes and then melted and cast into dore' bars for shipping. Issues of retort capacity and concerns over efficiency led to research into the retort process itself.

Jan 1, 1990

By Paul Grisley

Air-supported belt conveyors-conveying systems that replace troughing idlers with a film of air-were a revolutionary concept when introduced in the 1970s. But high installation and operating costs limited their application. Now, system refinements have led to successful applications, even under the challenging conditions of mines and process plants. In this presentation the author will discuss the latest developments in the engineering of these systems, including the ability to retrofit existing transfer points with modular air conveyor components. Air conveyor applications and limitations in mineral-handling operations will also be examined.

Jan 1, 2002

By Fulian He, Jianhang Chen, Dongdong Chen, Shoubao Zhang

"The Wangjialing Coal Mine is the main colliery of the China Coal Huajin Energy Limited Liability Company. The average thickness of the coal seam in District 201 is 6.21 m. Fully mechanized longwall mining was used in this district. The ventilation roadway of panel 20102 was influenced by the retreat mining of the adjacent panel 20104. Therefore, large deformation and severe roof falls occurred in this roadway, seriously influencing the safety production of this coal mine. To support the roadway, cable truss was proposed to strengthen the reinforcement of this ventilation roadway. First, numerical simulation was used to optimize the reinforcement parameters, including the cable installation angle, cable length, and eccentric distance. Based on numerical simulation results, in-situ tests were conducted in the ventilation roadway of panel 20102 with the cable truss technology. In-situ monitoring results showed that the roof-to-floor convergence and the convergence of roadway on two sides were within the safety range. Furthermore, no apparent separations occurred in the roof. These indicate that based on the designed parameters, the cable truss system can effectively maintain the roadway stability under the severe influence of the adjacent longwall mining.INTRODUCTIONCable bolts are flexible tendons composed of multi steel wires, which are wound into a strand (Chen, Hagan, and Saydam, 2018). They were initially introduced in the hard rock mining industry in the 1960s. Later, they found rapid application in coal mines to maintain the stability of excavations (Wang et al., 2015).The standard cable bolt is composed of seven steel wires with a diameter of 15.2 mm. Laboratory and in-situ tests showed that there is a low bonding capacity between the standard cable bolt and the grout (Craig and Holden, 2014; Chen, Hagan, and Saydam, 2018). Then, modified cable bolts are developed based on the standard cable bolts. They are improved by changing the surface geometry of standard cable bolts, such as birdcaged cable bolts (Hutchins et al., 1990) or nutcaged cable bolts (Hyett et al., 1993). Further tests proved that modified cable bolts have better mechanical interlock and friction between the cable bolt and grout, leading to larger load transfer capacity of cable bolts.Although cable bolts have been used for many years, failure of the cable bolting system still occurs. A common failure mode is the damage of surrounding confining medium while the cable bolt is still hanging in the roof, which is caused by the bond failure of the cable/grout interface (Hutchinson and Diederichs, 1996). To prevent the cable bolting system from failing, the cable truss system is more widely used in mining engineering."

Jan 1, 2019

By D. R. Nagaraj

Adsorption of sulfide collectors such as xanthate on pyrite has been studied extensively over several decades using a wide variety of techniques. In spite of this, there are unanswered questions as to the identity of adsorbed species on pyrite surfaces -dixanthogen vs. iron xanthate complexes. Far less is known in non-xanthate collector systems. We have used Secondary Ion Mass Spectroscopy (SIMS) successfully in the past to obtain direct evidence for the identity of the adsorbed collector species on copper sulfides, galena and Cu-activated quartz. The present study is an extension of the SIMS analysis to investigate the adsorption of xanthate, dithiovhosphate, dithiocarbamate, and modified thionocarbamates and thioureas on pyrite. Adsorption of these collectors on chalcocite was also studied for comparison. An attempt was also made to obtain SIMS spectra for pure dixanthogens at room temperature. Only in the case of dithiocarbamate (DTC) was there direct evidence for the presence of not only the collector dimer, but also iron-DTC complexes. On chalcocite, only the copper-DTC complexes were detected (no dimer). In the case of xanthate, the collector molecular ion and its S adduct -which are possible fragments from dixanthogen -were detected on pyrite, along with a fragment peak: suggesting Fe2X. For dithiophosphate, the collector molecular ion and Fe(DTP)(OH) complex were detected (no dimer). For modified thionocarbamate and thiourea, adsorption on pyrite was negligible.

Jan 1, 1997