Search Documents

By N. A. Abdel-Khalek

The objective of this investigation was to compare the results of counter-current flotation column versus conventional flotation cell for the cleaning of a sulphur ore and its discrete size fractions. The tests were carried out using diesel oil as a collector and alcohol as a frother. Generally, flotation column produced concentrates of higher grade. For example, the grade of a rougher concentrate for a given feed obtained with the column increased by 33% higher than that produced with the flotation cell. Such higher grade could not be obtained using conventional cell even after 3 cleaning stages. Moreover, the column gave superior results for flotation of fine and ultrafine particles.

Jan 1, 1991

By G. P. Brahmaprakash, K. A. Natarajan, N. Jyothi, K. N. Sudha

Some important electrochemical aspects involved in the bioleaching of mixed sulfides have been discussed with reference to selective sphalerite dissolution from different binary mineral combinations. Combination potentials and galvanic currents were measured in different binary combinations of sphalerite with other minerals such as galena, chalcopyrite and pyrite in order to under- stand the electrochemical dissolution behaviour of sphalerite when coupled with other minerals. The effect of applied DC potential was also studied with reference to selective sphalerite dissolution from a binary mineral mixture. An application of a potential of -500 mV (vs SCE) was found to enhance bacterial growth as well as selective sphalerite dissolution. Factors influencing bioleaching of sphalerite under a negative applied potential are discussed.

Jan 1, 1989

By Fredrick C. Kruger

We can confidently predict such obvious long-term trends affecting the minerals industry as - increasing consumption, exhaustion of easily discovered near-surface ores, and sharp limitations upon open pit mining by environmental considerations. There- fore, we must intensify the exploration for, and the development and exploitation of, deep bodies of potash and other ores. This paper examines the state of the art of the search for, and the evaluation of, potash from both a geological bias and a mining practicability. The use of indirect geological methods and geophysical techniques, followed by expensive deep drilling, are the conventional approach to evaluation and development of mining plans. The geologist and the geophysicist will have to find ways to perform both of these tasks better and cheaper.

Jan 1, 1973

By Janet E. Lamarre

Current statistics show that 90% of new-business failures are caused by the unsuitability of the entrepreneur for the business he has started. Are you a suitable candidate for success as a consulting geologist? Should you start your own geologic consulting business, and when? This paper investigates the demand for consultants with respect to general economic trends and mineral exploration activity trends. Furthermore, the study reveals certain technical skills and personal characteristics important to the success of the consulting geologist. Research shows chat certain expectations which prompted geologists to change careers are fulfilled while other unanticipated expectations often are also met.

Jan 1, 1985

By Steven H. Brown

Ore bodies which were once uneconomical to mine by conventional methods such as tunneling or open pits, have become attractive due to the development of nonconventional techniques, involving considerably less capital expenditure. Technologies such as uranium solution mining or in-situ leaching, have enabled commercial scale mining and milling of relatively small ore pockets of lower grade, and may make a significant contribution to overall U.S. uranium supplies during the next 20 years. Commercial size solution mining production facilities have operated since late 1975. Solution mining involves the pumping of ground water, fortified with oxidizing and complexing agents into an ore body, leaching and solubilizing the uranium in-situ, and then pumping the solutions to the surface where they are fed to a processing plant. Processing involves ion exchange, precipitation, calcining, and packaging operations. This paper presents an overview of the solution mining process and the health physics monitoring programs developed over the last four years at several production facilities as a result of the radiological character of these processes. Although many radiological aspects of the process are similar to that of conventional mills, conventional-type tailings as such are not generated. Some special monitoring considerations are presented which are required due to the manner in which radon gas is evolved in the process and the unique aspects of controlling solution flow patterns underground. An overview of the major aspects of the health physics compliance and monitoring programs that have been developed are discussed.

Jan 1, 1981

By L. MacHue

Sulfur containing collectors have been shown over the years to function as strong, selective and non-selective sulfide mineral collectors. Unfortunately, the majority of the widely known sulfur based collectors are of low molecular weight, volatile and subsequently, possess an objectionable odor. Higher molecular weight sulfur based collectors (C9 and higher) are significantly less odiferous due to lower volatility and lower vapor pressures. In this study, a specific proprietary higher carbon number collector, Orfom® MC 37, was blended and used successfully to recover 2-3% additional molybdenum in a laboratory flotation system, when compared to a standard collector blend. Copper recoveries were also positively affected. Further testing is required to give additional conditions favorable to increased copper and molybdenum recoveries, but indications at this time show the proprietary sulfur based collector blend to be a selective collector of molybdenum, while providing a significant increase in copper recoveries.

Jan 1, 2010

By Wenhua Wan, Jan M. Mutmansky

Many concerns have been expressed worldwide regarding the use of diesel equipment in underground mines due to the potential health risks associated with diesel particulate matter (DPM). In assessing the risk to the health of miners and designing control strategies for DPM, it is important to know the concentration of DPM in the working areas of a mine. In some mines, significant stratification occurs due to the characteristics of the diesel exhaust, affecting exposure and the ability to measure DPM concentrations accurately. This study outlines some of the concentration profile data obtained during sampling at three mines where diesels were employed. Mine #1 (a gold mine) employed large openings in which a diesel-powered roof bolter was used. Mines #2 and #3 are both room-and-pillar operations with varying conditions. Mine #2 is an experimental mine where two stationary diesels were utilized for sampling purposes, while Mine #3 is a traditional evaporite operation using two mobile diesel vehicles for section haulage. These field studies indicated that some level of stratification occurred in all the mines, but the stratification was not as pronounced in the case of Mine #2 due to the complex pattern of exhaust emissions generated by the vehicles. The stratification seemed to depend on the distance from the vehicle, the mine air velocity, whether the vehicles were moving or stationary, and whether the exhaust was diluted by equipment design features. The concentration of DPM was generally higher at samplers located near the roof and lower at samplers located near the floor. However, this was not found in all cases. This paper provides conclusions on how knowledge of stratification patterns can be utilized in sampling and control of DPM in mine atmospheres.

Jan 1, 1997

By Jerome C. Motz

Los tipos, tamaños y número de trituradores empleados en un sistema completo de reducción varían con factores tales como: el volumen de mineral que debe ser procesado, tamaño de la mina, tamaño máximo del todo-uno, dureza del mineral y de su roca soporte y tamano requerido para el producto final. Básicamente, sólo existen tres tipos distintos de equipos de trituración para la etapa primaria. Estos son: machacadoras de mandíbulas, trituradores giratorios y molinos de impactos, y cada uno tiene unas características operativas propias. Las trituradoras de mandíbulas operan por aplastamiento de las rocas entre dos paredes, una fija y otra móvil, en una cavidad determinada. Han sido ensayadas variaciones en la caída y movimiento, pero la mayoría de las máquinas del tipo Blake tienen un ángulo de trituración de aproximadamente 27° entre las mandíbulas fijas y móviles. El principio de trabajo del triturador giratorio es muy simple. Si un cono es montado en un eje vertical y la parte superior del eje se sitúa estacionaria mientras que la parte inferior gira excéntricamente, el cono tendrá también un movimiento excéntrico. Si el cono se coloca en una carcasa conveniente se movers aproximándose y retrocediendo de las paredes que lo contienen a la vez que gira. Si el cono y las paredes de la carcasa son suficientemente robustas y pesadas, cualquier cosa apresada entre ellas será triturada. Al lado de los incrementos de la eficacia desarrollados por las continuas acciones de trituración y el curvado de las caras de trituración, los trituradores del tipo giratorio tienen las siguientes ventajas: 1. La gran abertura de alimentación disponibles en comparación con trituradores de otro tipo. 2. El alto rango de tamaños y capacidades, que se encuentran entre 600 y 6.000 toneladas por hora. 3. Generalmente no es necesario control en la alimentación. Dumpers de 150 a 200 toneladas descargan directamente en las actuales instalaciones.

Jan 1, 1982

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity, drivability to safety. Accurate subsidence prediction, correct influence assessments, and effective mitigation measures are the keys to ensure the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures (e.g., road surface pavements, concrete slabs, transverse joints, etc.), vehicle dynamics, comfort level, and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed along with an application case.

By Robert P. Moodry

It was attempted to revitalize an old sulfide leach dump by increasing the oxygen content within the dump. Compressed air was introduced into the old dump. This was accomplished by drilling 300 foot angle holes into the dump surface with an Aardvark drill which holes are then cased with 1-1/2 inch perforated PVC pipe. Compressed air is injected through these cased holes during a 10 day rest cycle. The second case consists of bedding perforated polyethylene pipe at the interface between the old dump surface and the next Lift of a new dump. Compressed air is then blown through the bedded perforated pipe on a continuous basis while leach solution is applied.

Jan 1, 1976

By 1980, the U.S. mining community had reached a broad consensus regarding coal pillar design. The pillar load could be estimated from tributary area theory, and the pillar strength from empirical formulas and laboratory coal strength testing. Then the growth of longwall mining required new thinking. Recently, powerful design methods have emerged from analysis of large data bases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. Sophisticated numerical models have also helped transform the pillar design landscape. In the process, our understanding of pillar mechanics has been greatly enriched. A new paradigm divides pillar failure into three categories:

Jan 1, 1999

By W. L. Price

I. INTRODUCTION Today, there are two conflicting trends facing the designer of the bulk material handling system. The first trend is the necessity to stockpile increasingly larger amounts of bulk material (coal, ore, stone etc.) as economically as possible. Fig. 1 illustrates such a typical large storage pile. The second trend is the increasing awareness of the ecological problems of today manifesting itself in a new concern over possible air pollution from storage pile surface particles. The conflict between these two trends can become dramatic when this bulk storage pile is located near a heavily populated area. Strong winds can easily create a severe local problem by blowing the particles from the pile surface toward residential and commercial areas, igniting a crisis in public relations. (2), (3), (4). To help define our combined subject and ecological culprit more accurately, Fig. 2 shows the commonly accepted size range of dust particles. A descrip¬tion of the present state-of-the-art of dust control for large storage piles is the intent of this paper. II. OPEN STORAGE PILE SYSTEMS - ALTERNATE CHOICES AND RELATIVE COSTS In discussing the open storage dust problem and possible solutions, one obvious question arises - what are the economics of placing large bulk storage under cover? Part or this answer will be found in Fig. 3 - an approximate unit capital cost comparison between several methods of storage. It will be noted that the cost curve(s) for the closed concrete silo storage illustrated in Fig. 4 is cheaper per ton at relatively small tonnage capacities, but as tonnage increases, the open pile storage unit cost (B) becomes more economical. Curve (T) covers the cost of open storage using the plow feeder arrangement shown in Fig. 5. A gravity draw-down pile with feeders at the base as shown in Fig. 6 represents yet another open storage choice.

Jan 1, 1972

By A. López-Valdivieso, M. A. Corona-Arroyo, M. Llamas-Bueno

Magnetite (Fe3O4) ore is concentrated by low-magnetic-field drums to recover a magnetite concentrate that is low in silica (SiO2). The presence of SiO2 in the magnetite concentrate for steel production increases the steel processing costs, so a major challenge in magnetic concentration is to lower the SiO2 grade in the Fe concentrate. This work presents studies that were carried out on the removal of SiO2 from the magnetite concentration at the plant scale. Studies were performed with a three 36 × 96″ drum unit processing 46 ton/h of rougher magnetite concentrate. These studies showed that silica appears in the magnetite concentrate by three mechanisms, namely SiO2 entrainment in Fe3O4 chains, heterocoagulation between Fe3O4 and SiO2 particles, and mineral locking of SiO2 to Fe3O4. The SiO2 entrainment mechanism had the highest contribution (75%) to the SiO2 recovered in the Fe concentrate. Electrokinetic studies on Fe3O4 and SiO2 showed that heterocoagulation occurs because of the low negative zeta potential of the minerals at the pH of the plant slurry. This study also showed that a high percentage of ultrafine size SiO2 particles trapped in Fe3O4 agglomerates was not removed by the dilution water for the slurry fed to the drum. To lower the SiO2 recovery in the drum magnetic concentration process, work should be directed towards the removal of trapped SiO2 in Fe3O4 agglomerates.

Over the last two decades, the mining industry has spent considerable time and effort in installing sophisticated control systems (including expert systems) to regulate and improve the performance of AG/SAG mills. Yet the need for these systems is often overlooked – unmeasured and uncontrolled variation in the feed material. With AG/SAG mill technology replacing rod and ball mills as primary grinding equipment, the need for careful and thoughtful feed preparation has gone. To maximise mill throughput, operations need to better understand the ore characteristics affecting AG/SAG mill performance. Industrial operating data will be used to illustrate these ideas and concepts. It is often quite surprising which ore characteristics that are the most influential on mill throughput.

Jan 1, 2004

By J. Keng, S. T. Chen, T. M. Shih

Kwanyin Tunnel is presently the longest (7.7 km) railway tunnel in Taiwan. Due to heavy railway traffic, a pass-by station will be built inside the tunnel to increase the traffic flow. Since the concentration of toxic gases released by the locomotives may reach dangerous levels, a research program was conducted for the purpose of designing a ventilation system which could dilute and/or remove the toxic gases to maintain an acceptable pollutant level. The program consisted of two parts. The first part was field measurement during which the concentrations of pollutants and wind velocities were measured at various points inside the tunnel to acquire basic data regarding ambient air quality, piston effects for the different types of trains, and existing ventilation conditions. Weather data (temperature, humidity, atmospheric pressure, wind direction and velocity) were gathered at many stations, both on the surface and inside the tunnel. The amount of pollutants released by each type of locomotive for various conditions were also measured. The second part of this study involved establishing mathematical models for predicting the air quality of the various proposed ventilation systems. Three different models were used for this work. The first one is a piston effect model which assumes that the gases and air undergo immediate mixing inside the tunnel. The second one is also a piston effect model which assumes that the diffusion ability of the gases is zero. The third one is a conventional ventilation model which was used for natural and mechanical ventilation conditions. From the result of field measurement and mathematical model studies, a ventilation system was chosen with consideration of both ventilation effects and construction costs.

Jan 1, 1987

By Ning Liu, Di Yin, Xuming Wang, Yongqiang Lu, Jan D. Miller

Air-sparged hydrocyclone (ASH) flotation technology has been evaluated for phosphate recovery from the central Florida phosphate deposits. As expected, it was demonstrated in pilot-plant tests that the ASH system has a specific capacity about 50-100 times higher than that of a traditional flotation cell. In the case of fatty acid flotation, single-stage ASH flotation produced a recovery of 75-77% in a rougher concentrate containing 24% P2O5 In reverse flotation with amine, the single- stage ASH system produced a phosphate recovery of 98% in a cleaner concentrate containing 31% P2O5. These results are comparable with those obtained at plant operations in the Florida phosphate industry. Based on these pilot-plant results, the effects of process variables are discussed in terms of separation efficiency. Subsequently, a 6-inch ASH system was fabricated and tested in a central Florida phosphate plant for reverse flotation in the amine flotation circuit. The high capacity of the ASH system was again demonstrated for the 6-inch ASH system. A single-stage phosphate recovery of 91% was achieved with a concentrate grade of 30% P205. During plant tests, it was established that porous tube plugging, the most significant engineering problem identified, was due to the poor quality of the plant water. Possible solutions to this problem are discussed.

Jan 1, 1999

By R. H. Roberts

The Environment Weipa is located at 12° south latitude on the west coast of Cape York Peninsula, North Queensland, Australia. The climate is tropical with most of the 1 600 mm. average annual rainfall falling between November and March. During the short winter months (May/ August) the weather is clear and pleasant, with temperatures seldom exceeding 27°C.Throughout the remainder of the year, conditions are frequently oppressive due to consistent high ambient temperatures accompanied by high humidity. The terrain is of low relief, and generally not more than 6 to 10m. above mean sea level adjacent to the coast. The coastline features numerous short estuaries which discharge run-off from the heavy rains collected by creeks and rivers. The whole area is covered by an open forest, the predominant species of which is Eucalyptus tetradonta. These eucalypts have only limited commercial value and are heavily infested with termites. Despite the fact that Weipa is close to the location of the first reported sighting of the Australian coastline by a European (William Janz - 1606), it remains very isolated. There is no developed road or rail connection to centres of population, so that transport of practically all products, personnel and materials to and from Weipa is by sea and air. Cairns (population 49 000) is 580 km. by air and 670 nautical miles by sea; Brisbane, the

Jan 1, 1977

By Lei Zhang, P. Somasundara

The beneficiation of phosphate is complicated due to its sparingly soluble nature. The surface proper- ties of phosphate and associated minerals are determined, in addition to the ionic composition of the solution, by the dissolution of the lattice ions of the minerals and subsequent complexation, hydrolysis, adsorption, and precipitation of the dissolved species. These, in turn, are influenced by the pretreatment of the mineral. These complex interactions determine the interfacial properties of phosphate and associated minerals and thereby the efficiency of beneficiation processes such as flotation and flocculation. Under- standing of the chemistry involved in such systems is helpful to develop the optimum beneficiation schemes. It is shown that desired selectivity can be achieved by controlling the chemistry of the systems. More important, the need to conduct development tests under plant conditions is clearly demonstrated.

Jan 1, 1999

By M. M. Foss

Geophysical methods are gaining acceptance in the evaluation of coal mine ground control condition. The use of in-seam seismic investigations has contributed significantly to the body of information concerning ground control feature identification and analysis. Seismic methods have been used successfully in locating voids, faults, fracture zones, roof and floor rock interfaces, and more recently in characterizing in-seam stress distribution. Seismic tomography is an effective tool in data interpretation for several of these applications, but as is the case with other engineering application of geophysical techniques, there are limits as to how much substantive information can be interpreted from a given data set. This paper discusses some of the applications of in-seam seismic geophysical tomography, and the limits to which the transformation from raw data to information should be taken.

Jan 1, 1995

By Juan P. Camus, Sergio G. Jarpa

INTRODUCTION Chuquicamata mine is a large copper open pit located in the north of Chile. It has been in production for more than 80 years and now is in the later stages of its life with declining grades and increasing haul distances. As any old mine with long established organizations and procedures, it has faced one of the most difficult managerial problems: to conduct changes. Since 1994, the new management team has been devoted to a modernization pro- gram focused mainly in restructuring business operations. downsizing the labor force and introducing a mine planning pro- cess consistent with the company's goal. The explicit identification of the latter issue has been made because of the management’s conviction about the importance of it in the profitability of the business. The mine planning process at Chuquicamata mine has evolved from an old manual technique towards a modern computarized system, however the fundamental aspects and the procedures involved in this process have been the same. For in- stance, the cutoff grades policy has not changed during the last said 20 years, regardless of the changes to grade distribution, commodity prices, plant capacities, etc. To review and rethink this process, the strategy was to work with a small group of inside engineers and the management in order to interact with several mining consulting firms. The idea was to open a discussion about the fundamental principles used in the mine planning activities and, at the same time, to explore new ideas to improve the operating practices that have been followed for a long time. Thus, the goal of this paper is to present the mine planning approach that was the result of this work and the improvements that were obtained. THE CHUQUICAMATA MINE The Chuquicamata division is one of the five operations of Codelco and is currently devoted to operating the Chuquicamata mine; a copper open pit, concentrator, smelting and refining complex. It also operates Mina Sur which consists of an open pit mine, a leaching-solvent extraction and electrowinning process. There is also a dump leaching and a Sx-Ew plant for treating the low grade suifide ore (under the cutoff grade) from the Chuquicamata mine. Prior to reviewing the mine planning process, capacities for the Chuquicamata sulfide line were 640 000 tpd of run of mine material, 160 000 tpd of ore and 4 200 tpd of concentrate. This meant a total annual movement of around 230 Mt in the mine and a treatment of 57 Mt in the concentrator with a stripping ratio of approximately 3: 1. The old exploitation strategy consisted of an "open scheme", which means that all benches must have a berm with enough space to allow the traffic of large haulage trucks. This fact implied working with a great flexibility, but the consequences were flat slope angles. One of the reasons for using this operating practice in short term planning was that the grade consistency from the pit has always been a controversial variable. Schedules were designed to meet grade targets accurately and they were modified immediately when deviations become apparent. This reality led to working with a great deal of independent pushbacks and it required flexibility in the traffic system. The cutoff grade policy has been the same for a long time and the figure was 0.5 %CUT either for sulfide or oxide ore. This was the reason why a balance was produced between the mine and the concentrator. The mine is operated principally with benches of 26 m but in the upper part of the pit there are benches of 24 and 30 m. The main production equipment is shovels of 28 and 34 yd3 along with trucks of 200 and 240 st. Regarding the crushing facilities, there are two main systems located inside the pit and an old one in the periphery, close to a stockpile and near the concentrator. In the north part of the pit there is a crusher for waste material and in the north-east area is located the ore crusher facility. Both restrict a significant area of the pit and the mine sequence is considering to move the ore crusher again to the south-east sector where it used to be located. Relating to the waste crusher, the idea is to move it up to a bench near the surface in order to use the same conveyor belt and, at the same time, liberate an important sector. THE MINE PLANNING PROCESS The objective of the mine planning process is to develop a mine plan for the life of the deposit, in harmony and consistent with the company's goal. It includes the origin and destiny of tonnages and grades from the mine(s), along with the necessary resources to carry out this plan such as: fleet requirement, consumable goods, manpower, etc. From the financial point of view, it means to establish the cash flow for each time period of the mine life. That is. the revenue, capital investment and operating cost associated with each period of the plan. The fundamental principles involved in the mine planning pro- cess have been a controversial issue for a long time. One of the reasons for these divergent views could be produced by the difficulty of modeling a complete extraction policy for a geological re- source. This particular problem has to deal with several decision variables that are time dependent. So far, there is no mathematical formulation for managing such a problem, and the approach to solve it is based on a circular analysis combined with certain heuristic tools. So, a global model rather than a formula, requires a clear understanding of mine operations as well as economic theory and its application to a non-renewable resource. In order to manage this complex problem, the mine planning process can be conveniently split off in three stages which are conceptual, feasibility and operational planning. The characteristics of each stage are basically the timeliness in which they are developed and the kind and number of variables involved. Thus, conceptual planning is devoted to the definition of key variables like: the size of the operation, mining method, extraction se-

Jan 1, 1996