Search Documents

By Vivek Priyadarshi, VIVEK KUMAR HIMANSHU, A. K. Vishwakarma, M. P. Roy, A. K. Mishra, RAVI SHANKAR

The nature and orientation of joints in rock strata affect the damage pattern under explosive loading. Most of the limestone deposits in India are found with severity of joints. Categorically, these joints may have variable orientations such as dipping out of the blast face, inside the face, horizontally or having strike parallel to the face. The damage pattern under the varying category of orientation will be different. Accordingly, a numerical model in Ansys-Explicit Dynamics was prepared to compare the damages of rock mass under different joint orientations. The physical nature of a joint reflects frictional and stiffness behaviour. Accordingly, the damages have been compared under bonded and frictional nature of joints. The output damage pattern from the model has been validated on the basis of blastability index proposed by Lilly. Different limestone mines in India show different nature of jointing in their rock strata. Accordingly, the blasting outputs from three different limestone mines, viz. Rawan limestone mine, Sagmania and Birhauli limestone mine and Injepalli limestone mine, have been compared along with their blast design parameters and the nature of joint. The comparative results show that the closely spaced horizontal joints support maximum in burden movement and rock fragmentation due to blast.

Nov 23, 2023

By M. M. Champion

INTRODUCTION Since the first introduction of explosives into mining operations, safety considerations have prohibited the use of machinery in association with the explosives. Only within the last 25 years has this situation changed appre¬ciably; the closest thing to "machinery" used by a powderman in the "old days" was his wooden tamping stick. With the blackpowder and dynamite used during the first 150 or so years of mining blasts, substituting a drill steel or a metal "spoon" invited serious disaster. With the advent of ammonium nitrate-fuel oil (ANFO) explosives (1950s) and water-gel explosives (1970s) for underground blasting, machinery started to play a large part in blasting procedures. The lower sensitivity of ANFO and water gels allows these prod¬ucts to be loaded in a variety of safe ways. Not only has this meant cost savings in labor and blasting materials, but it has also resulted in whole new mining concepts where the limitations of dynamite previously made those concepts uneconomical, impossible, or excessively risky. Increasingly (totally for some mines), the traditional tamping stick has given way to a variety of pneumatic machines for loading explosives and blasting agents. The resulting blasting operations have become safer, more efficient, less uncomfortable for personnel, and a major step forward in mining technology. ANFO LOADING EQUIPMENT Three basic types of loaders are used for ANFO explosives, these being the pressure-vessel loaders, Venturi loaders, and combination loaders. Pressure-Vessel ANFO Loaders ANFO consists of prilled ammonium nitrate (porous pellets I to 2 mm in diam) and fuel oil in the appro¬priate 94 to 6% blend. The material is fairly dry, pourable, and easily conveyed by an air stream. One device or system for handling (hole loading) ANFO is the pressure-vessel loader. ANFO is dumped into the vessel or "pot," and the vessel then is pres¬surized. The ANFO is conveyed out of the bottom of the vessel into a semiconductive hose that has been inserted into the blasthole. Fig. 1 illustrates a typical pressure-vessel loader in use. Applications: The use of pressure-vessel loaders is widespread in room-and-pillar mines, including salt, potash, trona, lead, and other rubber-tired mines where the heavy pressure vessels can be mounted on a vehicle for transport from face to face. The vessel often is large enough to hold eight or more 23-kg (50-1b) bags of ANFO, so several faces can be loaded before refilling. Pressure-vessel loaders also are suitable for effec¬tively loading long holes such as those that are 6 m (20

Jan 1, 1982

By Richard R. Klimpel

This article introduces the basic definitions and philosophy behind process hazard evaluation procedures and the determination of risk as being a function of accident probabi1ity and accident consequence. The general concepts of good engineering practice and predictive hazard evaluation are discussed. The most commonly employed methods used in the processing industries are reviewed with an eye towards briefly presenting what each method offers as far as information, time and resources required, etc. Some initial references on the actual practical use of each technique in the processing industries are also given.

Jan 1, 1991

By Ashis Bhattacherjee, Rahul Upadhyay, Nearkasen Chau, Aditya Kumar Patra, Dhanjee Kumar Chaudhary

Heavy earth-moving machineries used in openpit mines intensively expose drill operators to whole-body vibration and shocks, and thus to musculoskeletal disorders. The roles of individual, machine and rock-related factors in their exposure remain poorly understood. This cross-sectional study investigated their roles in 39 drill operators from Indian iron ore mines. It shows that 70 percent of the operators were exposed to high levels of vibration, above the limit values recommended by ISO 2631-1 (1997). Multiple linear regression models showed that the whole-body vibration and shock exposures were strongly associated with operator’s age, drill-machine model and rock hardness, uniaxial compressive strength and density. The role of body mass index was close to significance (p = 0.08). Univariate analyses found the drill’s age, seat-pad thickness and seat backrest height were also strong predictors. These results help in identifying risky operators, materials and occupational situations, and in implementing appropriate prevention and intervention strategies to reduce and monitor the exposures and health risk. In addition, during the planning stage of acquisition of new equipment, anthropometric data of the operators should be considered for the ergonomic design of the seat.

By Terry Mattioli, Buck Bradshaw, Terry Fagg, Larry G. Nisle

Deposition of calcium carbonate scale on activated carbon in the Pinson Mining mill carbon column circuit was causing erratic gold recovery rate, long acid wash time, high carbon attrition and long strip times. Continuous addition of a blended antiscalant into the mill thickener overflow at 8 ppm reduced the average carbon acid wash weight loss from approximately 10% to < 2%. Cleaner carbon improved the gold loading rate in the mill column. The loading on Column I was increased to 175-225 oz/ton carbon from 125-150 oz/ton for a two-day carbon advance cycle. The higher loading capability has given Pinson more flexibility and better control of gold flow through their carbon adsorption, stripping and electrowin­ning processes. Preventing calcium carbonate build-up on activated carbon with this antiscalant reduced acid wash batch time. This enabled Pinson to acid wash and regenerate every batch of stripped carbon for all the adsorption circuits. Shorter strip times have also resulted from the lowering of the calcium carbonate scale level in the loaded carbon. Carbon consumption has been reduced and is now averaging 0.046 lb/ton ore for the first six months of 1990 compared to 0.072 and 0.083 lb/ton respectively in 1989 and 1988.

Jan 1, 1990

By John W. Trammell

The White Pine Mine is situated in Ontonagon County, approximately six miles south of Lake Superior, in the Upper Peninsula of Michigan (Figs. 1 and 2). The ore body mined by White Pine Copper Company occurs in the lower - most 20 to 25 feet of the Nonesuch formation, a series of middle - to upper Keweenawan shales, siltstones, and sandstones. This paper elaborates on the solution of problems in ore grade control and mine planning arising from the presence of an essentially barren sandstone stratum within the ore body.

Jan 1, 1964

By J. M. Rotter, R. A. Lohnes, J. Y. Ooi

Reliable prediction of wall pressures in a coal silo demands careful characterization of the stress-strain properties of the coal. This paper describes the results of triaxial compression tests on a typical fine-ground coal used in power generation and describes the fitting of several different constitutive models to the data. The fitted parameters for the constitutive models are well suited to application infinite element analyses. The different models are used to give the reader flexibility in choosing a model and to show the shortcomings of some models. To explore the quality of the fitting process, the fitted results are compared with finite element predictions of the triaxial test itself.

Jan 1, 1998

By T. M. Barczak, S. C. Tadolini

Reduction in the recovery time required and improvements in safety during a longwall face move have compelled coal mine operators to examine and use pre-driven longwall recovery rooms. The recovery entry is developed at the longwall stop position and supported ahead of time so that the required combinations of standing and internal sup-ports can be installed before the longwall face approaches. A calibrated three-dimensional finite element model, developed in conjunction with an underground test area, provided the critical components and design principals for a comprehensive parametric study. The study indicates that vertical, horizontal, and shear stresses concentrated on the outby abutment pillar corner of the recovery room resulting in deformations in the immediate roof above the primary roof support anchorage level. The results of the numerical model and field site observations indicated that the combination of the internal bolting system and the standing concrete supports are critical for the successful and safe extraction of the longwall equipment. Cable supports installed at and angle over the pillars can help stabilize the disturbed zone above the adjacent fender and outby pillars, however; standing supports are required in most sedimentary roof conditions to increase stability and assure a safe longwall extraction.

Jan 1, 2004

By K. Kavouridis

On 30 April 2004, a large scale slope failure incident occurred at the external waste dump facility of the South Field Mine, in the Western Macedonia Lignite Center, Greece. This landslide involved the mobilization of waste overburden material (that was continuously deposited for the last 20 years) in the order of 40 Mm3, while the material that moved outside the boundaries of the waste dump was in the order of 3 Mm3. The factors that led to failure as well as the procedures and measures taken in order to stabilize the failure and resume normal operations at the South Field Mine are presented and discussed. Emphasis is given to the impact on mine operations and the cost related to resuming of normal production operation as well as to implementing important modifications and improvements of the materials handling system.

Jan 1, 2006

By K. Hanumantha Rao, K. S. E. Forssberg, H. R. Manouchehri

The fundamentals of electrical separation, the electrical properties of minerals, the principal methods used for charging minerals and their mechanisms, the effective factors controlling the acquisition of charges by minerals, the general configuration of commercial electric separators and the forces operating during electrical separation of minerals are reviewed and presented.

Jan 1, 2000

By F. Montgomery Lyon

Pyritic sulfur in coal occurs as discrete mineral particles, and its liberation and physical rejection is the primary target for coal desulfurization. An acceptable solution to the pyrite removal problem from fine coal is not found in the standard methods of coal cleaning such as jigging, heavy-medium separation, tabling, and hydro-cycloning. Although fine coal is an ideal size for froth flotation, this method, as currently practiced is also unsuitable as the fine pyrite usually floats with the coal. One possible solution to this problem may be the froth flotation of pyrite from coal. This reverse flotation scheme would have the major advantage of removing both free pyrite and locked pyrite-coal combinations. With this possibility in mind, we have, as a first step, compared the flotation and adsorption. characteristics of an ore-pyrite and coal-pyrite with potassium-ethyl-xanthate as a collector 1 Related Research. The action of ethyl-xanthate on coal has been studied 2 by Horsley. He measured the contact angles of coal in distilled water and in the presence of purified ethyl-xanthate. The results indicated that the xanthate was not adsorbed by the coal. Additional contact angle data were obtained to determine the effects of cupric, ferric, and ferrous salts on the system. Then either the ferric or cupric salts were in, solution with the xanthate, there was an increase in the natural contact angles of the coal. This indicated that these heavy metal ions activated the flotation of the coal with xanthate. However, ferrous iron did not act as an activator. Horsley stated that the most attractive explanation was that the xanthate is oxidized to dixanthogen in the presence of the ferric and cupric ions.

Jan 1, 1971

By Stéphane Servant, Jacques Ouellet, Ferri Hassani

This paper presents essentially the logistic and practical aspects involved for in situ testing of mine paste backfill with a self-boring pressuremeter. The investigation discussed in this paper is part of an extensive and ongoing research project to identify and validate an in situ testing technique for cemented mine backfill such as hydraulic or paste backfill as well as Insitu behavior of backfilled stopes. After a literature review on field testing of soils and past experiments on mine backfill in situ testing, the self-boring pressuremeter was selected as the most appropriate instrument for this task. The authors presents in this paper the technical aspect involved in a field trials that was conducted in a Canadian underground mine using paste backfill. The results of this first successful trials show that self-boring pressuremeter test can provide high quality and reliable backfill characteristics results, using analytical techniques developed for soils (Ouellet et al., 1998). The parameters obtained were: estimation of the lateral stress in the ground, the soil stress-strain response and the soil strength. The logistic and equipment required to conduct such testing underground is fully described. Performance achieved in the field and technical difficulties encountered are highlighted. Recommendations for future experiments with such instruments are given. Some potential technical improvements to better adapt this in situ testing technique to mine backfill are proposed.

Jan 1, 2001

By Geoffrey G. Hunkin

This is a brief state of the art paper describing current (1975) Uranium recovery plant flowsheets, some notes on system selection, design philosophies, and materials of construction. The in-situ, or borehole solution mining, of Uranium is a process which has been developed over recent years to better match Uranium mining and milling technology with the size, shape, grade and territorial distribution of the remaining identified Uranium deposits of western United States. Solution mining recovery plants are pure hydrometallurgical units ideally suited to automation, modular design, and mobility. Similar to conventional Uranium mills, two basic flowsheets, one acid and one carbonate, are in use, but the predominance is reversed so that the majority of plants employ the alkaline carbonate flowsheet, All plants incorporate resin bead ion exchange Uranium recovery for both acid and alkaline circuits.

Jan 1, 1976

By J. A. M. Cano

With a view toward increasing its product competitiveness in the foreign market, SAMARCO MINERACAO S/A has developed high MgO type pellets at its pilot plant for performing direct reduction simulation tests. Additives such as dolomitic lime and magnesite were used for increasing pellet MgO content. Comparative direct reduction simulation tests were conducted both in SAMARCO and foreign laboratories. The test results showed that it is possible to produce direct reduction type pellets with satisfactory metallurgical properties, which can be successfully processed at increased temperatures in direct reduction furnaces.

Jan 1, 1992

By T. L. Myron

To determine the effect of flux crystal size on the production rate and strength of sinter, batch sintering tests were conducted on samples of both dolomite and limestone of various crystal sizes. In addition, calcination tests .were performed on the dolomite and Limestone to determine the effect of crystal size on calcination rate at various temperatures normally attained in sinter beds. The results indicate that flux crystal size does not affect sinter production rate or sinter strength.

Jan 1, 1962

By M. M. Rajkovich, L. Adams, J. J. Zaluski, S. Gardner

In 1998, a group called Kentuckians for the Commonwealth filed an Administrative Petition with the Kentucky Natural Resources and Environmental Protection Cabinet to designate 8,903± hm2 (22,000± acres) on Black Mountain, which contains the state&apos;s highest point, as unsuitable for mining. A fast track legislative process was triggered that could have "taken" 91 Mt (100 million st) of coal reserves or, in the alternative, imposed severe restrictions on mining. Even with all parties represented by reasonable individuals, this process can be extremely cumbersome and expensive. The legal and technical preparation for this unusual hearing process as well as issues and strategies of the negotiated resolution are reviewed

Jan 1, 2002

By M. S. Celik

Salt-type minerals are usually floated with anionic and cationic collectors. Flotation of a number of systems has been reported to remarkably increase above the concentrations where surface precipitation of collector-metal salt is initiated. Some studies attribute this phenomenon to heterocoagulation of oppositely charged collector colloid and mineral particles. In this study, examples are given on boron minerals to demonstrate that the high flotation region occurs when particles, colloidal precipitates and bubbles acquire a similar charge which induces Van der Waals interactions resulting in hydrophobic bonding.

Jan 1, 1995

By Arpad E. Torma

The introduction of biotechnological principles in hydrometallurgy has created new opportunities and challenges for the industry of mineral processing. During the 1950&apos;s and 608s, the mining wastes and unused complex mineral resources have been successfully treated in bacterial assisted heap and dump leaching processes, especially for the production of copper and uranium. The economic viability of bio- leaching technology lead to its world-wide acceptance by the mining industries. During the 1970&apos;s this technology grew into a more structured discipline which is called "biohydrometallurgy". Currently, bioleaching techniques are ready to be used, in addition to copper and uranium, for the extraction of cobalt, nickel, zinc, gold and silver from diverse mineral resources and for the desulfurization of certain coals. However, in a foreseeable future the biohydrometallurgical processes may be applied also for the treatment of high- grade ores and mineral concentrates using native and/or genetically engineered microorganisms.

Jan 1, 1989

By J. J. Moore

Combustion synthesis, or self-propagating high-temperature synthesis (SHS), reaction systems are discussed with respect to thermodynamics and kinetics. In particular, the effect of the process parameters, e.g. particle size, [All] ignition and combustion temperatures, on these self-sustaining reactions is discussed. Combustion theory is used to investigate the effect of the overall actuation energy of the SHS reaction on the combustion front propagation rate and in obtaining a clearer understanding of the transition from stable to unstable propagation. Finally, examples of the application of combustion synthesis to advanced materials processes are made, in particular the synthesis of Ni-Ti-X intermetallic shape memory alloys, TiC-AI2O3 and ZrB2-AI203 ceramic composite materials.

Jan 1, 1992

By Rainer Alles, Markus Keller

INTRODUCTION For overland conveyors of several kilometres length and as well as wide for conveyors designed for high mass flows, the cost for the conveyor belting share is 40% to 50% of the invested cost 173. The German Standard DIN 22101 is used for calculation and dimensioning of - conveyor belts and belt conveyor components. Developments in rubber technology and conveyor belt design required a revision of the standard released in 1982 121, which was published in August 2001 131. New research results and publications 16-9, 13-15] led to a better understanding of the material behaviour and their influences on conveyor belts. Test and calculation methods have been established to determine the most important parameters which are related to the performance of a conveyor belt line. These parameters are • The running resistance of the idlers • The indentation resistance of the belt • The dynamic splice efficiency • The distribution of belt load in the splices, transition zones and on pulleys. As a result, new rubber compounds with low indentation losses allow the use of reduced friction coefficients and thus lead to reduced power consumption, smaller drives and lower belt tensions. The deeper understanding of the flux of forces within belt splices led to both optimised splice design and optimised rubber compounds which significantly improve the dynamic splice efficiency. Therefore, in accordance with the standard, the benefits of these technologies and the better understanding of material behaviour allow a reduction of belt strength still maintaining sufficient safety factors. Thus engineers are enabled to calculate belt tensions more exactly and users are encouraged to pay more attention to starting and braking techniques. DETERMINATION OF DRIVE FORCE According to the DIN standards the resistance to motion generally has to be determined for each different section of the belt conveyor including upper and lower run separately. The necessary drive power P is calculated as [ ] with v as the conveying speed. The total of all resistances to motion of carry and return run can be determined as [ ] FHo and FHu are the primary resistances consisting of the running resistances of the idlers, the indentation resistance of the belt, the fulling of the conveyed material and the flexure of the belt. While indentation resistance and idler resistance are measurable, they have been deter- mined to be responsible for up to 70% of the primary resistances covered by FH. Further FN is the secondary resistance that covers, for example, the resistance of feeding points and scrapers. Fa are the total slope resistances and Fs is the total of all special resistances, resulting, for example, from belt steering devices. These three resistances should be neglected in the following discussion. For conveyors where a determination of the substantial parts of the resistances to motion is not possible, according to the new DIN standard [31 a determination of the drive power is acceptable by using the fictitious friction factor) [ ] In this formula the index i identifies the individual section of the conveyor, 1 is the length of the section and MR, MG and ML are the related masses of the idlers, the belt and the load in kg/m. The fictitious friction factor f determines the ratio between the overall resistance to motion and the total of moved masses within the

Jan 1, 2004