Search Documents

By Surendra K. Mishra

Metallic and oily components are the major contaminants of industrial wastes. Underground burial and incineration have been the commonly practiced methods of waste management. To provide a relatively more permanent solution, different processes have been developed. In addition to reviewing these processes, potential of using flotation as a process to treat hazardous metal and oil contaminated wastes is discussed in this paper.

Jan 1, 1989

By C. Haycocks

Damage prediction during multi-seam mining is an essential precursor to optimizing mine design. Ground control problems associated with interaction are influenced by both fixed geological and site conditions as well as mining variables which may be controlled to varying degrees. To quantify interaction effects across an affected seam a hazard map approach was selected, which allows interaction data to be presented in a form that can facilitate future planning. Study mines were analyzed using boreholes as sources of geological and spatial data, together with information from mine maps which gives the extent of mining activity. To demonstrate the method the safety factor against interactively caused shear failure in the lower seam roof was computed. Input data included depth of cover, inner burden thickness, remnant pillar size, extraction ratio, immediate roof type, seam thickness, percent sand-stone, and rock strength values. These safety factors were then contoured to produce a hazard map. An assumption was made to assign a high safety factor at the outcrop line to permit realistic contouring of the safety factors. The software also allowed mine workings to be drawn onto the map to facilitate interpretation of the overall results. Hazard analysis permits delineation of unsuitable mining areas within a seam. The application of the method for refining mine design and improving reserve recovery is verified using case studies.

Jan 1, 1992

By R. J. Matetic

Mining operations have long been accused of causing a disruption to local, domestic and agricultural water supplies. More recently, concern for water supplies has increased with the advent of high-extraction mining techniques, namely longwall mining. Theoretically, any water bearing zone in the overburden above a high-extraction mining operation may be affected by mining. In some cases, a confining bed may be fractured causing a loss of water to a particular zone. In other cases, increased fracture permeability may enhance the ability of an aquifer to transmit and deliver water. Unfortunately, only a limited amount of studies have been conducted that characterize hydrologic changes and also quant1fythe magnitude of mining-induced subsidence. The U.S. Bureau of Mines conducted such a study at a mine site located in Greene County, PA. A total of 8 water wells were drilled and hydrologic parameters such as specific capacity, transmissivity and well yield were determined both before and after mining. Electronic water level recorders were installed on each water well to provide continuous observations of water level fluctuations.

Jan 1, 1990

By Scott G. Britton

Up to now, the hands-on approach to construction has been stressed. This chapter reviews the basic tools available for construction design and monitoring of a construction project. It is divided into three discussions, all under the general title of computer aids, since the trend for using these tools-is via the computer. In the context of our discussions, the focus for computer aids will be on the use of evaluation and analysis techniques for coal mine construction applications, including mainframe programs, CPM techniques, as well as mini and microcomputer applications. Although the presentation of material in this chapter may be detailed at times, by no means does it cover the entire field of computer applications for design or project scheduling and monitoring. It is only an attempt to illustrate the possibilities that are available to construction and mine engineers. Interested persons can pursue computer applications for coal mining by reviewing Computer Methods for the 80's. by Alfred Weiss, editor, published by SME-AIME.

Jan 1, 1983

By J. L. Fuller

Mine ventilation surveys were conducted by Technical Support engineers during June 1987 and September 1989 at the Dutch Creek Hine. The mine is located near Redstone, Colorado and is operated by Mid-Continent Resources, Inc. Following completion of the initial survey, several recommended improvements were incorporated into the ventilation system by mine personnel. The second survey permitted documentation of the effects of those changes on the ventilation system performance. This paper describes the processes involved in the implementation of the recommended changes. The substantial improvements in system efficiency and reduced operating costs are also described.

Jan 1, 1991

By Janusz S. Laskowski

Studies carried out over the last 10 years reveal that precipitating particles which may appear in alkaline solutions of long-chain amines and in acidic solutions of fatty acids exhibit clear isoelectric points around pH 10.6-1 1 for dodecylamine and around pH 2.5-3 for fatty acids. These colloidal species can accumulate at solid/liquid and liquid/gas interfaces and affect flotation. While the precipitate in solutions of fatty acids apparently can chemically interact with the mineral surfaces and is flotation-active if sufficiently long conditioning time is available, the cationic flotation of quartz in alkaline solutions is depressed by the colloidal precipitate. The experimental data available in literature on the adsorption, electrokinetic, contact angle and surface forces measurements in the solutions of the weak electrolyte collectors are analyzed and the role played by the precipitate is discussed. It is shown that these concepts allow for an explanation of the selective flotation of sylvite from halite with long-chain amines in potash ore flotation.

Jan 1, 1999

By V. G. Hill

The term bauxite was first used by O.P.A.P. Dufrenoy in 1845 for an ore which was discovered by Pierre Berthier in 1821 near the village of Les Beaux de Provence near Arles in southern France. His data suggested that this mineral was an alumina hydrate with two molecules of water. However, it was subsequently shown by thermal analysis that the mineral was a fortuitous mixture of the mono-hydrate and the tri-hydrate. Diaspore had been previously discovered in 1801 and gibbsite in 1822. The term was however retained as a rock name. The name of the village was changed to Les Baux around 1885; Sainte Claire Deville suggested that the mineral name should reflect this, and it was changed to bauxite (Bracewell, 1962, Rkgnier, 1988). Mining of bauxite began around 1860 in the Auriol region in the Bouches du Rhine area in the south of France. This ore was transported toMarseilles by carts and was processed in the Salindres plant, which at that time was the only plant producing alumina using the Deville process and aluminum by the chemical process. During that period white bauxite (low iron content) was particularly sought after for the production of aluminum sulfate, refractory bricks, and quick setting cement. Export of bauxite from France began in 1880 and was initially delivered to Chemische Fabrik, Goldschmischen near Breslau, and to Guilini's Ludwigshafen plant in Germany in 1885. These companies produced alum and aluminum sulfate (RCg- nier, 1988). The next bauxite mining operation was in Antrim County in Northern Ireland in 1873. This was first used for the manufacture of alumina refractory bricks and quick setting cement (Bracewell, 1962). It is important to emphasize that initially almost all of the bauxite which was produced came from France and was mainly used for non-metallurgical purposes. At that time even the production of alumina was mainly for use as a mordant in textile dying. However, with the development of the Hall-Héroult process, the alumina which was available was increasingly used for smelting to aluminum. In spite of this the demand for non-metallurgical bauxite continued to increase and a set of applications were developed. These include refractories, abrasives (including the recently developed proppants), high alumina cements, aluminum chemicals, activated bauxite, and alumina. It became increasingly evident that the high alumina-low alkali raw materials have special advantages. The question however was one of cost benefit. Chin (1989) has pointed out that the non-metallurgical operations have been traditionally grafted on a bauxite/alumina/aluminum industry tree. In this context the non-metallurgical alumina produced was, with few exceptions, regarded as either coproduct or byproduct i.e.: Bauxite Trunk Sector Alumina Trunk Sector Aluminum Trunk Sector

Jan 1, 1994

By B. C. Flintoff

In general, process control systems in solid-solid separation have not evolved to the same level as in flotation circuit control. Perhaps one of the more significant contributing factors in this regard is the lack of suitable on-line analytical instrumentation. In spite of the obstacles, some interesting work has been done. This paper presents a review of current industrial control strategies in ore sorting, dense media separation, gravity separation and electrical and magnetic separation.

Jan 1, 1986

By Richard R. Klimpel

INTRODUCTION Froth flotation is the most widely used and economic means of concentrating metal sulfide ores such as those containing copper, lead, zinc, nickel, molybdenum, and pyrite. Also recoverable are other metal species that are often associated with sulfide ores, such as cobalt, platinum, gold, silver, etc. Flotation of metal sulfide ores has been successfully practiced at the industrial scale for more than 50 years. It is the relative technical/economic ease of floating metal sulfide minerals that has been a major driving force behind the rapid expansion in the supply/demand of metals over this 50 year period. It is estimated that 1.6 billion tons of feed sulfide ores are processed each year in the free world based on the froth flotation process, Klimpel (1987) and the manufacture/use of associated chemical reagents is a major portion of the 1.5 billion dollars (U.S.) free world mining chemicals business, Klimpel (1988b). The use of froth flotation appears to be increasing partially due to the ever decreasing feed grades and liberation sizes of the feed minerals. Froth flotation has shown itself to be a flexible process that lends itself well to many solid/solid separations. Thus, with surprisingly little equipment modification, separations can involve very different particle sizes and densities, and relative weight ratios of materials to be separated. In addition, the flotation process is economic, especially when compared to size reduction, its associated precursor process. Flotation also lends itself to continuous operations with a variety of equipment configurations. Such operations exhibit an ability to vary feed rate of solid to the process by as much as 50% without a total collapse of separating efficiency. In addition, the widely used mechanical flotation cell is scalable from 2.8 to 57 or 85 m3 (100 to 2000 or 3000 cu ft) with surprising ease relative to other unit engineering operations over the same relative size increase. The separating medium used is water. Most of the chemicals required -- pH regulators, frothers, collectors, activators, and depressants -- are all relatively inexpensive and common. They are not usually used in large quantities. While there has been a tendency for the quality of metal sulfide ores in any one geographic location to deteriorate over time due to mining intensity, the overall global supply of sulfide minerals is still very ample. Thus, the physical supply side of sulfide ore concentrates has not been under strong technology improvement pressure with increasing metal demands. Part of this is due to the ability of capital to consistently move to new geographic sources having suitable-grade sulfide ores. In these moves, the actual froth flotation technology used (including collector chemicals) has had to change little. As an illustration of this trend, of the approximately 80,000 metric tons of thio collectors used commercially (1980) in the free world, almost 987 were known and manufactured in some form 25 years ago. This is clearly not typical of reagent development in other process-related industries. In addition, the industrial-scale practice of froth flotation applied to sulfide ores has proceeded since the 1920's with often little direct (predictive) scientific explanation due to the extreme complexity of the flotation process. Empirical testing has been a mainstay of industrial flotation reagent development and use. Even today there is often strong disagreement between researchers as to the mechanisms of chemical flotation practices that have been performed successfully on an industrial scale for many years. Thus the industrial process of froth flotation, especially as applied to the recovery of sulfide minerals, poses a dilemma: such a process is widely used, economic, versatile, forgiving, etc. and yet is still not very well understood in a mechanistic sense leading to prediction of results from fundamentals even after 50 years of usage. Lack of such predictive ability has not limited the general over-all industrial use of froth flotation in sulfide mineral recovery. Rather the lack of

Jan 1, 1989

By Donald Bishko

Zoning is the legal means by which land use can be controlled. Although zoning laws have historically been quick to prevent quarrying, one is hard pressed to find zoning ordinances which specifically state that land should be used (or held in reserve) for quarrying and prevent other uses such as recreation, housing, etc. This situation is especially true when the mineral to be quarried has a low intrinsic value such as sand, gravel, and crushed stone. The chance of a gold mine surviving urban sprawl is probably considerably greater than that of a sand and gravel pit, even though it is possible that the dollar value of the sand and gravel' would exceed that of the gold mine. The research reported herein was concerned with two major topics: to delineate the real costs associated with the non-protection of our construction aggregate resources (growth minerals) and to develop a computer simulation model which would aid planners in making economically sound decisions. This paper describes the problems faced by the mineral aggregate industry and discusses the role of computer simulation in planning problems. It briefly describes a simulation model which has been developed and previously reported12 and discusses the results of a pilot study conducted on the Tri-City area (Albany, Schenectady, and Troy, New York). 3

Jan 1, 1970

By R. A. Speirer, T. C. Bettinger, L. P. Richardson

INTRODUCTION The Bureau of Mines (The Bureau) remote sensing researchers at the Denver (CO) Research Center, have been investigating computerized methods to detect and map surface linear features called "lineaments" for ground hazard assessment in mines. Many of these lineaments at the test mine site were found to correlate to subsurface geologic discontinuities such as faults, fractures, and joints that intersect coal seams at depth. These features adverse1 y affect the roof and rib integrity in underground mines, thus contributing to rock failures that may result in injuries to mine workers and loss of production. Advance knowledge of the existence of such hazardous geologic features can aid in mine planning and development. Lineaments may be observed in a variety of images of the earth's surface. Linear features that can be observed using Landsat mu1ti spectral scanner data (MSS) images range from regional (greater than 3 miles in length) to an intermediate length of from 1 to 3 miles. These images are recorded in discrete radiation bands in the green, red, and near-infrared portions of the el ectromaynetic spectrum. These data are acquired from the EROS Data Center of the U.S Geological Survey, Sioux Falls, SD, in digital format on magnetic tapes that are suitable for processing on certain minicomputers. Shorter lineaments length (less than 1 mile) can be observed in high- to low-a1titude aerial photography, radar, and infrared images with image scale ratios of 1:1,000,000 or less. These linear features can correlate to smaller dimensioned faults, and to fracture and joint sets at the local geologic scale. Other informational sources can help substantiate 1ineament analyses, such as well logs, mine naps, topographic data, and geophysical data acquired over the study site. These data must be in a digital format to process on the "DEC PDP 11/23 minicomputer system1". Data can be acquired in

Jan 1, 1986

By William J. Halvorsen

We are currently doing work on three ways to improve the performance of our froth flotation systems. One development is the use of a cationic flocculent added to the feed of the froth cells. This does give some improvement in ash of the product particularly in a situation where there is a good bit of clay present. Difficulty is usually experienced with clay carrying over with the water contained in the froth product and also adhering to the coal surfaces. Addition of the flocculent to the flotation feed preferentially flocculates the clay causing it to drop into the tails. The results of some laboratory test work on Pittsburgh 88 Seam coal in Eastern Ohio is shown in Table 1. [ ]

Jan 1, 1979

By Michael J. Shulman

During-all phases of exploration limited resources must be allocated among exploration methods and among exploration prospects. This problem,, an exercise in optimization, can be treated mathematically. For three objective functions - maximizing return, return to cost and return minus weighted cost - theoretical results exist which enable the exploration planner not only to gain valuable insight into the problem, but also to estimate the resources necessary and to allocate these resources for' at least-two stages of exploration prior to initial field work. A two-stage exploration strategy for volcanogenic-sedimentary iron in northern Egypt illustrates, how the results can be used. Stage 1 consists of an aeromagnetic survey to map the structure of five areas;" stage 2 consists of field reconnaissance work. For the three objectives, lower bounds are calculated as a function of exploration expenditures for each stage in order to facilitate the choice of an-optimal exploration budget. Nomograms are then presented which, based on the Kuhn-Tucker Conditions', enable the incremental allocation of airborne and reconnaissance effort among the five areas.

Jan 1, 1989

By Jennifer Gallagher

The Henderson molybdenum mine, near Empire, CO, has operated since 1976 using a panel caving process and a rail haulage transportation system. After two decades of service, the rail haulage system required a substantial capital expenditure to improve operations. The timing for this worked well because Henderson was able to combine this capital need into a mine plan that addressed process bottlenecks and current mining practices as a new production level was designed and developed. This process was a logical step, following an equipment upgrade program, and became known as the Henderson 2000 project. One of the key components of Henderson 2000 is a new ore transportation system. Throughout Henderson's life, the bottleneck has been the rail haulage system. Henderson staff evaluated several transportation alternatives and decided on a truck haulage configuration feeding an underground crusher and conveyor system. This configuration will eliminate the haulage bottleneck and will allow the mine to increase capacity. The installation of this system will be completed by the year 2000. The second key component of Henderson 2000 is the development of a new 7175 production level to extract the lower reserves of the ore body. Henderson staff benchmarked other caving operations and compared their mining practices to Henderson's basic mining guidelines. It became apparent that Henderson's practices could become more efficient, particularly in the areas of drawpoint spacing and column heights. These concepts were incorporated into the layouts

Jan 1, 1998

By R. L. McNearny, K. A. Barker

Four numerical models written with the "PFC2D " program were compared against four similar physical models. The numerical models were constrained numerically to closely follow the caving behavior of the physical models. Results from the numerical analyses closely simulated both the granular and blocky behaviors of the physical models, including bridging and interlocking of the simulated orebody during draw. The drawdown patterns and the rate of draw developed during numerical modeling also closely simulated the physical models. The same assumptions and governing parameters used in analyzing the first four models were applied to an additional model. The fifth model employed a completely different, uneven, draw sequence than the other four models, allowing the material to flow in a more granular manner with a demonstrated instability of the undercut sections between each drawpoint opening. Drawdown patterns and behavior of the numerical material of the first four models progressed at uneven and inconsistent rates, similar to those seen in the physical models. By inspection, the overall shape and flow lines of both the numerical and physical models were close in the area removed and in the flow characteristics. The fifth model proved to be the most unstable of all the models tested, with poor correlation to the physical models. The uneven draw sequence, coupled with an additional frictionless wall condition and an added drawpoint, caused the material to flow in a very granular manner. Information generated by this study can be used as a first approach in determining the proper draw rate, drawpoint spacing and undercut thickness for a block-caving operation. Numerical models are often difficult to predict and interpret. However, this study should increase the confidence level for use of the PFC2D program in the future.

Jan 1, 2000

By E. Woodburn, Harrison R. Cooper, R. Putman

The key to concentrator automation is practical means for obtaining continuous assay data from concentrator streams. The technique most successfully used is x-ray fluorescence analysis. The practical reality of on-stream x-ray analysis has been achieved through effort over the past twenty years, marked by an occasional breakthrough, but more typically a step-by-step development to which many individuals and organizations have contributed. The net result of this progress is the present capability to install on-stream x-ray analyzer systems on a turn-key basis. It is now possible to provide all components of an x-ray analysis system as a completely engineered unit which can be put into immediate use, minimizing needs for specialized application know- ledge to benefit from continuous assaying in process control. The economic factors which influence the choice of system and limitations of the x-ray fluorescence technique for slurry analysis are reviewed.

Jan 1, 1976

By G. P. Richards

RIP is the process of recovering uranium from an unclarified slime pulp which comes in contact with a moving bed of ion exchange resin, T e sand-slime separation of the acid-leach slurry is accomplished through the use of cyclones and spiral, akins type classifiers. Course sands are discarded to tailings and the combined slimes and leach liquor become the IX feed. Uranium in the IX feed is absorbed on the resin and after exhaustion the barren pulp is directed to tails, Following the uranium exhaustion cycle an eluant solution passes through the resin bed stripping the uranium from the beads, The uranium is precipitated from the clarified pregnant eluant, filtered, dried and packaged for shipment to the AEC, Normally, the ore received at the Mines Development plant is a loosely cemented sandstone containing small quantities of clay and bentonite, The ore is easily crushed and requires only a 1/3 load of rods in the rod mill to reduce the ore to grain size, Very little of the ore is recirculated by the 42" spiral classifier.

Jan 1, 1958

By Matthew E. Fowler, Jean Habimana, Roy F. Cook

The West Side CSO Tunnel, Pump Station & Pipeline Project is currently beginning construction along the downtown waterfront of Portland, Oregon. This4.3 meter diameter, 5,500 meter-long soft ground tunnel will be driven along the westbank of the Willamette River adjacent to buildings and utilities and several major pile-supported bridges. High groundwater pressure, extended lengths of gravel to cobble-size alluvium, and the need to control ground loss and surface settlements were key considerations in the selection of slurry tunnel boring machines for the project This paper presents an overview of the numerical modeling that was performed during design to estimate the strains and additional loads in the pile-supported structures and to assess the efficiency of proposed mitigation measures.

Jan 1, 2003

By D. R. Nagaraj

Secondary Ion Mass Spectroscopy (SIMS) was used to study copper ion adsorption, and its effect on subsequent sulfide collector adsorption, on pyrite and pyroxene minerals under flotation related conditions. Copper was found to adsorb on both of these minerals and cause enhanced sulfide collector adsorption. The distribution and depth profile of copper and collector on these mineral surfaces were obtained by using SIMS in the imaging mode. The results of this study have provided a valuable insight to understanding pyrite and gangue flotation observed frequently in operating plants.

Jan 1, 1995

By Robert C. Bates

Published information discussing uranium mine radon daughter controls and related costs was examined and used to develop an estimated (projected) cost per ton for any level of control. Results show a clear power function increase of cost for conventional dilution ventilation as the annual exposure limit is lowered. Projections can be made using any assumed changes in consumer price index (CPI) and radon daughter working level months exposure limit. Bounds on the estimated costs are provided, and applicability of the final equation is discussed.

Jan 1, 1983