Search Documents

By R. C. Woodhead

During past years the most difficult problem presented to the coal preparation engineer has been the cleaning of fine coal, The problem of handling fine coals is more involved than the coarser sizes, because the higher surface moisture contents complicate screening, and the larger percentages of fine near size material complicate separating problems. Low gravity high capacity specific gravity separations were not possible with equipment available at that time. Coal preparation engineers did develop machines that would effect a separation of the fines, however, to maintain a high efficiency, the point of separation had to be a relatively easy one. The more difficult separations were made in the coarse coal sections of the washeries, and the fines were generally cleaned at higher specific gravities in equipment such as tables, feldspar jigs, rheolaveurs, etc. Clean products from both processes were mixed, resulting in overall lower ash contents, During the last several years, however, we have been confronted with increasing demands ZGP more precise separations of finer coals to still further reduce ash contents. A study was begun and a program instigated to improve the cleaning of fine coal, The result of this endeavor was the development of the new cycloidal heavy medium cyclone.

Jan 1, 1964

By Mehmet Guney

[The Atlantis-II-Deep is a hydrothermal mineralization located along the median valley of the Red Sea at a water depth of about 2200 m. Extensive exploration of the metal-rich brine deep revealed a potentially mineable deposit on economic interest consisting of oxides, silicates and sulphides with considerable concentrations of zinc, copper, cadmium and silver. Geostatistics was applied to assess the most likely in-situ vague of the metal potential for economical exploitation. Semi-variograms were constructed to characterize the structure of the regionalized distribution of the geological parameters. Volume grades and thicknesses were determined by the kriging technique, avoiding systematically biased high or low grades, and then block .tonnages were computed. The estimation variances, distribution of errors and histograms of observed and kriged values in each grid Mock were also produced.]

Jan 1, 1983

By L. Alan Weakly

The U.S. Department of Energy (DOE) has entered into a $l.5 million Cooperative Agreement with Alpine Equipment Corporation/Astro International Corporation ("Alpine") of State College, Pennsylvania, for the evaluation of water-jet-assisted (WJA) mechanical cutting of oil shale under actual mining conditions. A commercial-sized, heavy WJA mechanical miner is being assembled based upon the successful "factory testing" of a smaller prototype miner utilizing standard tungsten-carbide and Polycrystalline Diamond Composite (POC) bits in large oil shale boulders. Actual field testing of the machine will be conducted in an oil shale mine located in the Piceance Basin of Western Colorado. In-mine logistical support is being provided by several oil shale companies through the Colorado Mining Association (CMA) and the U.S. Bureau of Mines (USBM).

Jan 1, 1990

By Jesse L. . Jr. You

Tunnels in the granitic Climax stock at the Nevada Test Site were inspected for keyblock occurrence. Thirteen relatively large pyramidal keyblocks were located in about 230 m (750 it) of tunnel. Orientations, dimensions, joint roughness coefficients, and joint compressive strengths were measured for the faces of nine keyblocks. The measurements were used to back-analyze keyblock stability to check the validity of a numerical model for keyblock behavior. A newly developed three-dimensional numerical model correctly predicted whether or not each keyblock failed in six of eight cases. The two exceptions involved stress conditions and keyblock locations that clearly violated the assumptions that underlie the stability model. The observations also allowed the effect of tunnel orientation on keyblock occurrence to be evaluated. Of the thirteen observed keyblocks, nine large blocks were found in less than 30 m (100 ft) of the Piledriver drift (which runs N56E) while only four blocks of comparable size were observed in 200 m (656 ft) of the Spent Fuel Test--Climax drifts (N61W). The orientations of the keyblock faces were checked against known discontinuity set orientations; some of the faces correlated well with mean set orientations, whi.le other faces were fringe members of sets. Stereographic techniques were used to examine the frequency of keyblock occurrence and to determine the maximum keyblock size that could be encountered with a given combination of discontinuities. Keyblock occurrence was found to be affected by tunnel orientation in a predictable way; this can be used to guide or improve tunnel design practices.

Jan 1, 1986

By Vijenac Quarry, A. Iljazagic, t. Knezicek, T. Omeragic

Limestone quarry Vijenac, is one of the key limestone producers in B&H. Conventional massive drilling and blasting is the technique applied for limestone exploitation. Utilized blasting scheme causes appearance of large oversize stone pieces, uncontrolled flying stone and undesirable seismic effects. In order to reduce or eliminate exposed disadvantages and to improve environment in the area of Vijenac quarry, an innovative blasting scheme was tested. Conventional blasting scheme was changed from single row, deep inclined blast holes combined with two lines short horizontal holes to multi row, inclined blast holes combined with a single line short horizontal blastholes. Applied innovative blasting scheme reduces negative blasting impact on the environment through safer working conditions, reduced amount of dust after blasting, reduced explosive and energy consumption, reduced appearance of explosive gasses and reduced earth and air vibrations as the result of seismic effects.

Jan 1, 2005

By Charles C. L. Smith

A review and comparison is made of the circuitry utilized for dc crane control systems. Anti-parallel three phase full wave thyristor bridges for dc motor reversing and speed control are compared with a single three phase full wave thyristor bridge for speed control and either contactor or static switching for reversing control to obtain complete four quadrant operation for crane material handling. In recent years the Harnischfeger Corporation has developed a solid state adjustable voltage control system to control the speed and direction of dc motors for crane applications and handling materia1.1 Shunt wound dc motors are utilized and speed is controlled in the motor base speed operating region at constant torque by a thyristor, silicon controlled rectifier (SCR), adjust- able armature voltage supply. The three phase thyristor bridge is the power controlling element of the dc adjustable voltage control. ELECTROTORQUE is the Harnischfeger Corporation registered trade name for this type of drive system. By controlling the gating signals or firing pulses to the thyristor bridge SCR's the dc output voltage can be varied over a wide range. This range is limited only by the magnitude of the ac applied voltage. To obtain operation of the motor in both directions two thristor bridges are connected in an anti-parallel arrangement. A typical schematic for two anti-parallel connected three phase SCR bridges is shown in Figure 1.

Jan 1, 1973

By Kathleen Y. Knoebel

This paper describes a graphical mini computer system called MPASS 2 (Mine Performance Analysis/Simulation) which has been designed to conduct analysis of underground room-and-pillar mining operations using both conventional and continuous mining methods. Dynamic, graphic displays of mine face machine activities are presented on the CRT screen to provide extensive visibility into underground mining activities. MPASS 2 consists of: an interactive inputting system that graphically creates a room-and-pillar mine and describes the mine when production is initiated; a time-step simulator that produces statistical summaries of shift activities and uses CRT screen graphics for accelerated-time display of machine activities and delays; a statistical analysis subsystem for analyzing mine performance data; an industrial engineering system that permits users to enter actual machine activity statistics and replay mine operations on the CRT screen; and a data management system to store historical performance information on mine characteristics and operations. MPASS 2 operates on a Hewlett-Packard 9845B mini computer with 450 K bytes of extended memory, and is written in H-P BASIC. It has been installed at Freeman-United Coal Mining Company in West Frankfort, Illinois and at the U. S. Department of Energy Pittsburgh Mining Technology Center. Applications include production system simulation, industrial engineering analysis, production scheduling, new equipment evaluations, and training.

Jan 1, 1982

By G. H. Roybal

Humic-acid-rich deposits exist in Arkansas, Florida, Louisiana, New York, North Dakota, Michigan, Minnesota, Texas, and Wyoming (Burdick, 1965) and in New Mexico (Shomaker and Hiss, 1974). New Mexico humic deposits are associated with coal in the northwestern part of the state where humate and weathered coal are presently mined. Discussion of the humic -acid industry in New Mexico requires an understanding of complex terminology and coal geology. TERMINOLOGY Humic material is not a pure substance so an ambiguous and complex terminology is in use by geologists, chemists, soil scientists, agronomists, and producers. Material mined for its humic-acid content is an extremely variable mixture of base-soluble humic, fulvic, and ulvic acids and their salts, formed during partial or complete decay of organic matter. This decay releases a high-molecular-weight organic material which is darkly colored, partly colloidal, and weakly acidic.

Jan 1, 1985

By A. F. Stewart

Slope design in an open pit mine includes the determination of a number of parameters, including bench height, bench face angle and berm width. By way of a case history of two highwall slopes (160m and 220m high) excavated in dipping strata in an operating coal mine, this paper illustrates the influence that bench face angle can have on the stability of an entire slope. The two highwall slopes, the lower of which experienced significant instability, were excavated in essentially the same lithologic and structural environment, with the main differences between the slopes being the angle at which the bench faces were excavated and the excavating methods that were employed. In addition to describing the instability that occurred on one of the pit walls, relevant aspects of the engineering geology, slope design and excavation procedures are described.

Jan 1, 1998

By Ronald L. Wiegel

Success has been achieved in developing mathematical models of rod mills, ball mills and recently to a limited extent autogenous grinding mills. There is also considerable activity in the development of mathematical models of various mineral concentration opera¬tions, such as flotation, magnetic separation and electrostatic concentration. However, at present there is a technological gap which hinders the integration of both size reduction and mineral concentration models into an overall process simulation model. This gap exists because size reduction models have been aimed at describing the size of the product and have not dealt with the equally important problem of identifying the product composition in each size fraction. Without this information the concentration model is ineffective. This situation is especially critical in the simulation of the magnetite-taconite beneficiation process, where a portion of the ore is rejected from the process following each stage of size reduction. Consideration has therefore been given to the merging of a size reduction model and a mineral liberation model to permit prediction of mineral composition as a function of size. The results of this integration of size reduction and mineral liberation models are discussed from both theoretical and practical viewpoints using batch grinding data for a magnetite iron formation sample as a demonstration vehicle.

Jan 1, 1975

By J. M. Avasthi

Gulf Research & Development Company conducted the nation's first underground coal gasification test in steeply dipping beds near Rawlins, Wyoming. The geotechnical considerations played a major role in the initial site selection. The test plan included a detailed geotechnical program for site evaluation, test design, permitting, and environmental studies before the burn. During burn, the geotechnical activity continued in the form of monitoring surface subsidence and acoustic emission. The postburn evaluation included studies of the drill cores obtained from the burn zone and effects on the surrounding rock mass.

Jan 1, 1981

By Brian Y. Lattimer, Kray D. Luxbacher, Jonathan L. Hodges, Manuel J. Barros-Daza

The abstract discusses the importance of predicting fire response time (the time before conditions become untenable for firefighters) in underground coal mines. It introduces a data-driven approach using artificial neural networks (ANNs) to predict response time and fire size based on measurable parameters like CO concentration, mine geometry, air velocity, and time since fire detection. The approach was tested using simulations from fire models (FDS and FSSIM), showing promising results for real-time predictions during mine fires.

Mar 6, 2022

By Duk-Won Park

Ground water has been a problem in underground mines (Anon., 1981; Aughenbough, 1973; Stansbury, 1981). Water migrates from water-bearing formations and surface water bodies such as lakes, ponds or creeks into the underground workings through fractures and cracks. As a result, under- ground workings become plagued with the necessity of having the water pumped out in large quantities. Underground workings become flooded when unexpected amounts of water flow into the openings, especially when mines use pillar extraction or longwall mining methods. It is difficult to detect water bodies above the coal mine roof before water problems take place. The resistivity method was used as a method for detecting water saturated rock layers and bodies of water above the roof of a coal mine in northern West Virginia, where the multiple seam mining method was being used.

Jan 1, 1983

By Alphonce Wikedzi, Mussa D. Budeba, Samwel V. Manyele, Sospeter P. Maganga

The present study provides an overview of the challenges and opportunities in processing complex gold-copper ores. The systematic literature review was conducted using Scopus database and seven-step methodological approach. The study indicates that the major challenges in processing complex gold-copper ores through the conventional cyanidation method include (1) increase in cyanide consumption; (2) increase in cyanide destruction cost; (3) low gold recovery; (4) decrease in adsorption efficiency; (5) decrease in electrowinning efficiency, and (6) difficulties in the measurement of free cyanide concentration in the leaching system. Moreover, the study indicates that several methods have been developed and some have been implemented in the mining industry for processing complex gold-copper ores. This includes ore segregation, pre-aeration, pre-treatment methods (e.g., ammonia), alternative lixiviants (e.g., thiosulfate, thiocyanate, glycine), cyanide destruction methods, and cyanide and copper recovery technologies. The study concluded that using lixiviant mixtures (e.g., cyanide-glycine), pre-treatment with environmentally friendly reagents (e.g., glycine) and the integrated membrane-based process (SuCy process) are new directions in processing complex gold-copper ores. However, more investigations are required to advance these processes to a commercial scale.

Sep 30, 2023

By A. S. Ibrado

Research investigations on the chemistry of the adsorption of gold cyanide on activated carbon have mostly reduced the role of activated carbon as the provider of the large surface area needed for adsorption. Most do not go beyond suggesting that oxygen functional groups on carbon play a key role in the adsorption process. Our research shows that the nature of the material, specifically its structure, is a crucial factor in the adsorption equation. To delineate the effect of adsorbent properties, gold cyanide was adsorbed on a series of carbonaceous adsorbents, including lignite, coals, anthracites, carbon blacks, graphite and activated carbon, which covers wide variations of composition, surface acid group content, and degree of graphitization. The results show that the adsorption of gold cyanide per unit area of adsorbent is not related to the amount of oxygen groups on the surface or even the total oxygen content of the material. However, they show very strong correlation with the degree of graphitization of the adsorbent, which indicates that the graphitic plates of activated carbon play the most important role. The findings suggest that majority of the adsorption occurs on the plate faces of the graphite crystallites of activated carbon.

Jan 1, 1992

By Seppo] [Kreula

Outokumpu Oy has acquired considerable experience with on-stream X-ray fluorescence analyzers and with computer control of flotation processes over several years. It became evident at the outset of this work that a reliable and accurate on-stream analyzer was more than a collection of different pieces of hardware linked together. Extensive work was done to develop an integral analyzer system, beginning with process samples through the spectrometer to report typewriters, recorders and the control computer. To date, over ten Courier-300 analyzer systems based on this development have been installed world-wide, several of which provide the key information for successful computer control systems. Computer control of flotation processes has been under development at the Pyhäsalmi concentrator since 1968. Two different control strategies have been implemented. The copper flotation is controlled by means of a mathematical model and economic criteria, whereas the "evolutionary operation principle" is applied to the zinc flotation. The computer control system installed at' the Vuonos-mine has been developed according to the same guidelines. In order to consolidate this wide experience, a flotation computer control system, Proscon-100, was developed by Outokumpu Oy, and the first system was installed at Kotalahti in 1972. In addition to the technological experience, enough information has also been gathered to illustrate the economical, benefits accruing through the use of these advanced tools of automation.

Jan 1, 1973

By Paul B. Queneau, Barry J. Hansen, D. Erik Spiller

Most lead and zinc secondaries are recycled pyrometallurgically. However, many problems encountered in secondary smelters have been solved by addition of physical concentration and/or hydrometallurgical processing steps, with resulting important environmental benefits. U.S. secondary lead and zinc operations are described, covering conventional smelters, EAF-dust treaters, and zinc sulfate/fertilizer producers, including plant capacities, technologies, and outputs. During the past two decades, remarkable advances have been achieved by recycling spent lead-acid battery components. Interaction between primary and secondary zinc producers, the fertilizer industry, and the zinc chemical industry has substantially decreased waste generation.

Jan 1, 1993

By M. Liu

In-situ soil washing using surfactants shows great potential to remove hydrophobic organics from subsurface environment. Lab scale soil washing experiment were performed using Sodium Dodecylsulfate (SDS), an anionic surfactant, and anthracene, a highly hydrophobic compound. The results of this research show that solubility of anthracene increases linearly with an increase in SDS concentration above the critical micelle concentration. Furthermore, SDS can be effective in removing anthracene from contaminated sand.

Jan 1, 1992

By PDF

Flotation columns are widely used in mineral processing and coal preparation industry today. Mathematical modeling of flotation columns has conventionally been done using axial dispersion or tank-in-series models. However, for design and scale up purposes these models are not adequate enough because they do not provide detailed information of the flow fields within the column. This paper presents a Two-Dimensional, Two-Phase. Fluid-dynamic Model and its numerical solutions for some cases encountered in column flotation. The MAC (Marker and Cell) method was employed to obtain the numerical solutions, and based on this method a computer code COLUMNFLOW was developed. The simulated flow field reveals the presence of a circulation flow structure in flotation columns, which could be one of the main reasons for mixing in column flotation. The effects of some parameters such as superficial gas and liquid velocities on the characteristics of the flow structure in flotation columns were also tested with the numerical model.

Jan 1, 1994

By M. Westerstrand

The processes involved in the concentration of magnetite ore with process water as the aqueous medium can have a strong influence on the surface properties of the magnetite particles. In this study, different leaching methods, as well as zeta potential measurements, were used to examine the major easily accessible ions on the particle surfaces and their effect on the surface charge. The results show that the enrichment of elements on the surface of the particles appears early in the refinement process. Ca was enriched up to 15 times and Si up to 50 times compared to what pore water alone would have given. The leaching experiments also showed that the addition of water glass increased the surface enrichment of Si and that the collector might hinder desorption of Ca. An alkali leaching method was evaluated, which showed that Si was much more enriched than S and Cl. Zeta potential measurements on synthetic magnetite particles showed that process water resulted in zeta potentials different from the potentials measured for these particles in aqueous calcium and silicate solutions. Therefore, it is important to consider the complexity of the process water when making predictions about the properties of the particle surfaces in the final magnetite concentrate, which most studies do not. Zeta potential measurements were also used to rule out a strong influence from organic matter in the process water on the magnetite zeta potential.