Search Documents

By William E. Horst

Ore grindability data based on various techniques to measure comminution characteristics are used to evaluate the crushing and grinding efficiency in mineral processing operations. The importance of achieving improved comminution efficiency, in terms of energy consumption, has been emphasized by recent increases in the cost of electricity. From a theoretical standpoint, the objective of a grinding operation might be expressed as maximizing the production rate at a given grind size while minimizing the energy consumption per ton of material ground. To achieve this objective in an industrial operation presents a challenge especially in view of changes in the raw material which are normally encountered. Various procedures1-5 used to determine energy-size parameters and grindability measurements have been reported. The proposed relationships between particle size and energy consumed have much in common between many of the techniques for measuring grindability. Probably the most widely used parameter to measure ore grindability in recent years is the Bond work index6, Wi, which is defined as the kw-hr per ton required to break from infinite size to a product size of 80 percent passing 100 microns. If the breakage characteristics of a material remain constant over all size ranges, then the calculated work index would be expected to remain-constant since it expresses the resistance of material to breakage. However for most naturally occurring raw materials differences exist in the breakage characteristics depending on particle size, which can result in variations in the work index depending on grind size. Consequently work index values are generally obtained for some specified grind size which typifies the comminution operation being designed or evaluated.

Jan 1, 1975

By Chuang Sun, Feng Luo, Guo‑dong Li, Xue‑qing Li, Tuan He

The mining-induced failure of the coal seam floor is essential for water inrush. The mining disturbance to the floor, especially in the thick coal seam, is severe, and the water inrush risk is also higher than that in regular thick coal seam excavation. The superposition of many stresses, including in situ stress, mining-induced stress, and confined water pressure, must be considered in the prediction of the floor failure depth. This study adopted the elasticity analysis, FLAC3D numerical simulation, and on-site acoustic wave test comprehensively. The thick coal seam working face of the Zhong-Yu coal mine affected by confined water was selected as the engineering background to study the characteristics of the floor failure. Based on elastic foundation theory and the superposition principle, the mechanical model and the failure depth criterion of the floor were established, respectively. The distribution and evolution of mining-induced stress and the plastic zone in surrounding rock during the mining process are obtained by FLAC3D. In addition, the changes in the P-wave wave velocity in the floor before and after mining were compared and studied by the acoustic wave test method. The range of floor damage depth is determined on the basis of the above research.

Jun 8, 2022

By Cyrus W. Field

Metalliferous sediments constitute an important component of the sedimentary veneer that overlies basaltic oceanic crust of the Nazca Plate and elsewhere. Although first collected more than one century ago near the East Pacific Rise during the Challenger Expedition and recognized for their anomalously high content of Fe and Mn, occurring as very fine-grained, yellow-orange, oxides, hydroxides, and oxyhydroxides, it was not until the more detailed studies of Bostrom and Peterson (1966) that their geologic significance and concentrations of other transition metals were fully appreciated. The Nazca Plate is a dynamic lithospheric unit bordered by the Peru-Chile trench and the East Pacific Rise to the east and west, and by the Galapagos Rift and the Chile Rise to the north and south (Fig. 1). Samples employed in this study were taken from piston core recovered from the Nazca Plate (Fig. 2), D. S. D. P. drill core from the northeast Pacific (Dymond and others, 1973), ferromanganese nodules from dredge-haul s at several locations, and from hydrothermal mineral deposits of the Andes. Our efforts have been largely sponsored by the National Science Foundation through its International Decade of Ocean Exploration Pro- gram. The metalliferous fraction of these sediments is widespread, but generally small. Sedimentation is dominated by biogenic silica in the equatorial latitudes, terrigenous debris adjacent to the South American Continent, and by biogenic carbonate elsewhere, except at depths below 3500 m in the central and northwest parts of the Nazca Plate near the East Pacific Rise. Contributions of these distinctive sediment types are shown by the distributions of Si02, A1203, and CaC03 given in Figure 3.

Jan 1, 1982

By E. Ashworth

A thermistor probe has been developed to measure in situ temperature profiles underground. A full description of the probe is given. Data collected from the probe has been used to compare the actual profiles with those predicted from a finite element analysis using laboratory measured thermal properties of the different rock types. This comparison indicates the applicability of laboratory measured parameters in modeling the real conditions. Factors such as applied pressure, moisture content and anisotropy on laboratory measurements is discussed.

Jan 1, 1983

By Walter C. Jr. Sherman

6.1-SOIL MECHANICS WALTER C. SHERMAN, JR. 6.1.1-DEFINITION Soil mechanics is concerned with the behavior of soils in relation to the design, construction and performance of engineering works. In this context, soils include all uncemented materials, such as, gravels, sands, silts and clays, either naturally or artificially deposited, and, under certain conditions, weakly cemented, badly broken or weathered rocks. Many types of mine wastes have physical properties similar to those of soils and thus are amenable to analysis by the principles of soil mechanics. The principles of soil mechanics are used to solve such problems as the stability of various types of structures with respect to failure of the supporting soils, determination of soil pressures and deformations in the design of foundations and retaining structures, analyses of seepage and under seepage, and stability with respect to sliding of excavated and natural slopes and embankments. 6.1.2--SOIL PROPERTIES Soils are classified on the basis of index properties, such as, particle-size distribution and plasticity characteristics. The Unified Soil Classification System1 used to classify soils for engineering purposes is shown in Table 6-1. Other physical properties important from an engineering standpoint include natural water content, density, permeability, shear strength and compressibility. Physical properties are evaluated on the basis of carefully conducted laboratory tests. Procedures for laboratory testing are presented by Lambe. 2 Soils, either of natural or artificial deposition, are complex three-phase materials consisting of solids, water and gas (usually air or water vapor). One of the most important principles in soil mechanics is based on the concept of effective stress in the soil-water system. A stress, a, applied to a saturated soil is taken partly by the soil particles (effective stress, a'), and partly by the water in the voids (neutral stress or pore water pressure, u,) so that a' = a - u,. Only the effective stress affects the mobilization of frictional resistance between soil particles. In partially saturated soils, the pore-water pressure is negative due to capillary effects. The effective stress relation remains valid for small negative pore pressures, but anomolies arise if the soil is significantly unsaturated. In this case, the pore pressure is commonly assumed as equal to the pore air pressure, u,, so that [ u' = u - u..] 6.1.3--SOIL EXPLORATIONS Soil explorations are carried out by borings or test pits. Hvorslev3 has reviewed procedures and boring requirements, such as, type, depth and spacing employed. In general, soil strata are logged and representative exploratory samples are recovered for classification purposes and for determining the subsurface soil profile, which is constructed utilizing also knowledge of the geology of a site. Undisturbed samples are recovered if the properties of the undisturbed soil are required, as generally is the case. The undisturbed soil sampler consists of a thin-wall tube

Jan 1, 1973

By J. H. Dietz

The electric assist option for diesel-electric trucks can improve truck productivity while maintaining the inherent flexibility of a truck and shovel operation. In addition, the resulting cost reductions offer a rapid investment payback for many mine situations. A review of the present technology and performance experiences verify the projected benefits in productivity and operating cost. New technologies can further improve the productivity/cost scenario.

Jan 1, 1984

By R. W. Utley

The purpose of this study was to seek and evaluate possible relationships between the composition of coal refuse, as expressed by washability data, and factors affecting the product ion of a lightweight aggregate from refuse by bloating. The study was related to an intense program in the Department of Mineral Preparation at the Pennsylvania State University to study the possible elimination of air pollution from coal refuse fires by producing a low- carbon secondary refuse. Another phase of this program is considering possible uses of such a secondary refuse. Thus one study was to determine if a lightweight aggregate could be produced from this new refuse material and what effect the nature of refuse beneficiation would have upon the characteristics of a commercial aggregate product.

Jan 1, 1965

By J. S. Hall

The performance of a full-scale balling drum circuit is well known to fluctuate, and is difficult to control. The fluctuations stem from causes that are not readily quantifiable. Results from plant tests show that surging of the recycle tonnage is dependent, inter alia, on the method of bentonite addition, small variations in drum or cutter bar speed and the method of drum water addition. This paper presents detailed observations from experiments on full-scale drum circuits, including preliminary results of a computer measurement and control scheme. Size distributions measured at points along an industrial drum are presented, together with the results of a mathematical model fitted to one plant data set. Model predictions are also included emphasizing the importance of screen performance on circuit stability.

Jan 1, 1983

By Richard B. Stein

This paper will present an overview of several hydrometallurgical processes which can be used for sea-nodule metal recovery and some simplified economics. Before going any further, here are some of the basic figures from which the economics were developed. The first is to establish a representative composition for a typical nodule feed (Slide 1). This set of chemical analysis figures can be taken as typical for a deep Pacific nodule feed and shows manganese at 30%, copper at 1.1%, cobalt at 0.2%, nickel at 13% and iron at 10% for the metals of economic interest1.

Jan 1, 1982

By Donald M. Hausen

Microscopic evaluation of trace quantities of metalliferous phases in flotation products requires counting large numbers of particles. Particle counts of many thousands may be required for precision, but not obtained practically by conventional microscopic techniques. A less tedious microscopic method for evaluating trace sulfides in mill tailings was developed for the O'okiep Mining Company in South Africa. Hundreds of thousands of particles were evaluated by this method called "gross-counting." Gross-counting consists of counting microscopic fields rather than point-counting individual particles. Total counts are calculated by multiplying the average number of particles per field by the total number of fields examined over the entire mount. Total gross-counts range from about 20,000 particles for +200 to 100,000 or more for -400 mesh size material in lucite mounts. Sulfides and metallic particles in each field are identified and tallied along with field counts. Totals for each type of metallic particle are divided by the total gross-count to give volume percent which is corrected to weight percent by specific gravity factors.

Jan 1, 1969

By S. Nunoo

The shape of particles has a significant effect on the shear strength and deformational characteristics of granular materials. Weathering can change the grain shapes. For example, more weathered sands tend to be rounder regardless of particle size. Particle shape analysis was performed on samples collected from the Questa mine rock piles, a debris flow and the pit alteration scar. In order to increase the validity of the particle shape analysis, 4 persons including 2 geologists and 2 mining engineers were involved in describing the particle shapes. The results of this analysis indicate that rock fragments in the collected samples are mainly subangular, subdiscoidal and subprismoidal. The sphericity and angularity of the rock fragments of the older analogs are similar to those of the rock piles. This suggests that short-term weathering (<100 years) has not noticeably changed the particle shapes at the test locations. Rock piles made of more angular particles are more stable compared to rock piles with rounded particles.

Jan 1, 2009

By Xuehui Li, Xinshuai Shi, Jun Wang, Jianguo Ning, Shang Yang, Zhaohui Zhang

Pressure relief is an important step in preventing and controlling rock burst disasters. Hydraulic slotting has emerged as a strategy for pressure relief and energy release in roadway surrounding rock. There is no qualitative description for the response relationship between hydraulic slotting parameters and the degree of pressure and energy release in a roadway, which is a scientific problem. In this paper, theoretical analysis, numerical simulation, and on-site industrial practice were comprehensively used. First, a structural model for the pressure relief and energy release of coal by hydraulic slotting in a deep roadway was established, and the pressure relief and energy release principle by hydraulic slotting was revealed. The principles and methods for determining hydraulic slotting parameters in the roadway were proposed. Three evaluation indices for the pressure relief and energy release effect of coal after hydraulic slotting were proposed, namely, the stress ratio of coal, elastic energy density ratio of coal, and displacement rate of the roadway rib. According to the evaluation indices, the degree of pressure relief and energy release was divided into three levels: reverse pressurization, full pressure relief, and transitional pressure relief. Then, a FLAC3D numerical model was constructed, the levels of pressure relief and energy release under different hydraulic slotting parameters were analyzed, and the optimal slotting parameters were determined. Finally, on-site industrial practices were carried out in Panel 7312 of the Xinhe Coal Mine. An effect test showed that the effect of pressure relief and energy release was remarkable after hydraulic slotting was adopted on the roadway surrounding rock, which can effectively reduce the risk of rock bursts. These research results can further improve hydraulic slotting technology systems and provide a theoretical basis and technical reference for the stability control of deep roadway surrounding rock.

Sep 20, 2023

By Neil D. Donnell, O&apos

Bituminous sands of the Lower Cretaceous McMurray Formation in northern Alberta constitute the ore for the surface mining operation at Syncrude Canada Ltd. These sediments represent a complex succession of fluvial, estuarine and marine depositional environments. Grade prediction is realized through a combination of geological interpretation, computer modeling, and reference to past mining experience. Accurate forecasts of feed grade permit reliable predictions of volumes for removal to meet budgeted synthetic crude oil production. This planning facilitates efficient allocation of mining equipment and resources. The feed grade to the Extraction Plant is monitored at various points along the delivery system.

Jan 1, 1984

By O. D. Christensen

The Carlin Trend is a 60 km (38 mi) long northwest alignment of epithermal, sediment-hosted, disseminated gold deposits. Collectively, these orebodies contained more than 620 t (20 million troy ounces) of gold. The Carlin deposit, located near the center of the Trend, has become the "type" deposit of this class. There are, however, significant differences between the individual deposits. Six subdistricts can be distinguished, based upon geographic, structural, lithologic, alteration, mineralization style, and geochemical characteristics. They are, from northwest to southeast, the Bootstrap, Bluestar-Goldstrike, Lynn, Maggie Creek, Rain and Bullion (Railroad) subdistricts. Regional Geologic Setting The Carlin District is located centrally within the Great Basin Geologic Province. Host rocks for the deposits include sedimentary units that range in age from Ordovician to Mississippian, as well as a Jurassic-Cretaceous granodiorite stock. During the Early Paleozoic, the area that is now Nevada lay along the western margin of the North American continent. A westward-thickening wedge of sedimentary units was deposited offshore in a eugeoclinal basin; these vary from continental shelf carbonates toward the east to fine-grained siliceous clastic and cherty units to the west. Tectonic activity associated with the Antler Orogeny in Late Devonian to Early Mississippian time resulted in the eugeoclinal Western Assemblage rocks being thrust as much as 140 km (90 mi) eastward over time-equivalent transitional to miogeoclinal Eastern Assemblage rocks along the Roberts Mountains Thrust fault system. The leading edge of the Roberts Mountains Thrust plate formed the emergent Antler highland from which siliceous clastic sediment, eroded from the overriding eugeoclinal rocks, was shed eastward into the adjacent foreland basin. Erosional products derived from the overthrust plate are termed the Overlap Assemblage.

Jan 1, 1987

By Jorgen Elbrond

In a stream of ore in an underground mine or in a beneficiation plant bins are installed between machines or machine system. When the upstream machine is stopped the downstream machine can continue operation for a while and vice versa. The paper describes a procedure for calculating the total capacity of a system consisting of two machines with an intermediary bin as a function of the bin&apos;s live volume and of the installed machine capacities and their production variations, which are defined. Extensions to several machines in parallel and in series are shown as well as practical examples.

Jan 1, 1982

By N. M. Levine

This work defines and systematizes the physical factors of the problem of leaching and demonstrates for the first time the utility of macropore volume, micropore volume, specific surface, pore size distribution and permeability as parameters of leaching based on a study of the recovery of uranium from the Top Black member of Chattanooga Shale.

Jan 1, 1962

By A. E. Isaacson

Bureau of Mines researchers developed and tested equipment to measure corrosion rates on a commercial-scale mill. Bench-scale experiments were designed for duplicating ore grinding conditions closely enough that realistic rate determinations can be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1987

By Frank A. Jerabek

Problems of mine backfilling and fill material deposited underground, the characteristics and relationship between the deposited fill material and overlying ground, and the practical applications and limitations of hydraulic backfilling as ground support are discussed. A great variety of materials ranging from coal washery refuse to concentrator tailings is used as hydraulic fill. Some materials will solidify and cement; others will resemble quicksand, Hydraulic fill as ground support is more efficient in inclined mine openings than in horizontal mine openings, where it cannot be placed tightly to the back. This and other deficiencies of hydraulic backfilling led to the development of pneumatic stowing. Research work in hydraulic backfilling at the Pennsylvania State University is also discussed. This research work includes the investigation of segregation in the discharged fill slurry, the quantity of solids escaping in the drain liquid, the relationship of escaping solids to slurry concentration and discharge rate, and the compressibility of fine fill material.

Jan 1, 1965

By Clayton J. Parr

Introduction This chapter contains brief discussions of various environmental protection requirements that relate to underground mining operations. Environmental disturbances at an underground mining operation can result from subsidence; water discharges; waste dumps; construction and operation of access roads and utility lines; construction and operation of surface facilities such as maintenance shops, bathhouses, and storage yards; and emanation of dust and noise from surface crushers. Construction and operation of a concentrator or washing plant may result in the emission of air pollutants, the discharge of water pollutants, the creation of noise, and disturbance of the surface. Tailings ponds can be the source of fugitive dust.1 This chapter is not intended to provide a detailed discussion and analysis of laws and regulations dealing with environmental protection. Rather, its purpose is to provide the engineer with a basic awareness of the existence and nature of such laws and regulations, as well as the procedural requirements that must be followed in complying with them. The body of law relating to environmental protection has grow" very rapidly and should continue to do to for some time. Because many of the laws have been enacted recently, numerous court decisions are being rendered to resolve disputes over their interpretation. Hence, the reader is cautioned to be alert for subsequent modifications of statutes and regulations, and new case law. Rules and regulations pertaining to environmental protection are implemented at all governmental levels. The most widely known laws are those enacted by the federal government that have nationwide applicability. However, separate requirements exist in each state, county, and municipality. Because of their general applicability, federal laws are discussed most extensively in this chapter. Ownership of the property is the most significant factor considered in ascertaining what rules govern the conduct of an operation thereon. If the land is held under lease, reference to the lease terms must be made in the first instance to determine what obligations must be met in order to prevent default and possible loss of the property. If the land is held under a lease from the federal government, the operator is subject not only to compliance with the lease terms, but also to a large body of laws and administrative regulations that pertain generally to the conduct of mining operations on land held under federal leases. Although operations on unpatented mining claims, the legal title to which remains in the federal government, are not subject to the same rules and regulations that are applicable to operations conducted pursuant to federal leases or permits, they soon will be governed by a special set of regulations that provide for protection of surface resource.2 Operations conducted on lands leased from a state usually are subject to numerous environmental protection requirements specified in the lease terms, in addition to rules and regulations promulgated by the state agency having jurisdiction over mining on state lands. Operations conducted on privately held lands are subject to fewer such requirements. Leases from private parties sometimes have environmental protection and reclamation requirements written into them, but generally to a far lesser extent than governmental leases. Operations conducted on properties owned by the operator are subject only to those laws and regulations that have general applicability without regard to land ownership. COAL SURFACE MINING CONTROL AND RECLAMATION ACT OF 1977 Introduction On Aug. 3, 1977, the Federal Surface Mining Control and Reclamation Act of 1977 was signed into law.3 It governs coal-mine operations on private lands, as well as on public lands. The Act is pervasive in its scope and is extremely long and complex. The basic purpose of the Act is to control and minimize the environmental effects of surface coal mining. Surface coal-mining operations are defined as activities conducted on the surface of lands in connection with a surface coal mine and surface impacts incident to an underground coal mine.4 The Act is administered by the Secretary of the Interior through a new agency named the Office of Surface Mining Reclamation and Enforcement.5 The Act contains detailed environmental protection standards and reclamation requirements, and it establishes a permit system for all surface coal-mining operations. Mining in certain areas and under ceri-in conditions is restricted or prohibited, and a mechanism for enforcement by the states is provided. Stiff penalties are provided in the event of noncompliance. Implementation Schedule Nonfederal Lands: As required by Section 501 of the Act, interim regulations setting mining and reclamation performance standards based on and incorporating standards set out in Section 502(c) were adopted effective Dec. 13, 1977.6 They will. be incorporated as amendments to Chapter VII of Title 30, Code of Federal Regulations. Permanent regulatory procedures for surface coal-mining and reclamation operations performance standards, which were directed to be promulgated by Aug. 3, 1978, were published in proposed form on Sept. 10, 1978. 7 They govern surface coal-mining operations in any state until a permanent state or federal program is adopted. As of Feb. 3, 1978, all new operations, and as of May 3, 1978, all existing surface coal-mining operations, on lands on which such operations are regulated by a

Jan 1, 1982

By James M. King

Analytical models for transient groundwater phenomena, such as those of Theis, Cooper, and Jacob, are important but often limited tools for aquifer evaluation and drawdown prediction. Most were developed using simplifying assumptions which compromise their treatment of complex boundaries and most also contain functions that are mathematically complex and difficult to solve explicitly. Examples of such functions are the Bessel functions, the exponential integral, and similar well functions for leaky confined and water table aquifers. This paper describes the joint use of simple numerical techniques and numerical approximations of these functions to extend many analytical models beyond their conventional applications. The enhanced analytical methods represent many hydrologic problems more easily and realistically, permit a wider range of application, and often provide insight into the response of pumped groundwater systems without the need to resort to more complex numerical flow models. Use of the enhanced analytical methods usually requires the use of microcomputers due to the large number of computations. Examples presented here are the development and extension of type curves and the determination of drawdown distributions.

Jan 1, 1984