Search Documents

By Jerry G. Rose

This paper addresses a process by which both the disposal and utilization of preparation plant coal refuse can be simultaneously accomplished with an attendant benefit of significantly increasing the percentage of extractable coal. A laboratory study is described in which coal refuse was successfully utilized as an aggregate in low cost concrete (coal-crete) mixes under simulated mine environments. Coal-crete specimens with compressive strengths of 14,000 kPa (2,000 psi) were consistently produced. A construction sequence and mining plans are offered for placing the low-cost coal-crete pillars in accessible areas in room-and-pillar mines so that a Substantial portion of the remaining coal pillars could be extracted. The method could be applicable in areas where mining procedures do not permit pillar extraction because of possible surface subsidence, roof problems, or other conditions. Possible structural difficulties with the coal-crete pillar support system are discussed. Using a discounted cash flow analysis, the economic feasibility of mining with the coal-crete pillar system is investigated. The cost of the coal-crete pillar system is compared to the cost of a mining system which would have less coal recovery. The analysis indicates that although at higher coal selling prices the coal-crete mining system may yield an acceptable rate of return, the alternative of leaving the coal pillars is more attractive at the present time.

Jan 1, 1977

By Yoginder P. Chugh

Physical mine modeling and computer simulation techniques were used to conduct technical feasibility and economic analyses of selected pit configurations for surface mining a single coal seam dipping at about 15 percent to a maximum depth of 150 feet. The pit orientations along the dip (dipline), strike (strikeline) and along an apparent dip were studied. Physical models of each pit configuration were prepared first to delineate potential operational problem areas, and also to furnish a data base-for the computer simulation models. A dragline micro- simulation model (Fluor), a shovel/truck simulation model and a cost analysis model were used to conduct the study. Sensitivity analyses were conducted on variables such as the pit width, block length, and angle of dip. The productivity (Cu.yds/hour) of the mining equipment (dragline or stripping shovel) under each set of conditions was used to optimize the pit configuration. Both block length and panel width were found to significantly affect the dragline productivity larger size trucks were preferable to smaller size trucks in the pit configuration along an apparent dip. The cost analysis results showed that the pit configuration along the seam dip was more economical than the pit along the strike or along an apparent dip.

Jan 1, 1984

By R. C. Emmett

In extractive metallurgy, separation of insoluble solids from solutions is an important economic factor in almost all flow- sheets. This separation step can employ sedimentation, filtration (vacuum and pressure), or centrifugation. Since practically all systems require a relatively complete separation, multiple unit, countercurrent thickeners or vacuum filters are generally used.

Jan 1, 1974

By Donald M. Podobnik

The Cuajone Concentrator of the Southern Peru Copper Corporation is located approximately 900 kilometers southeast of Lima, Peru, near the 500 year old town of Moquegua, in an area that has been occupied since antiquity. Since the plant was started in July, 1976, the throughput has steadily increased from 36,000 to 46,000 metric tons per day. The widely distributed molybdenite content of the ore body ranges from 0.02 to 0.04% MoS2. The molybdenite content of the copper concentrate has always been sufficient to justify operation of a byproduct molybdenite plant. During the first nine months of 1980, the average grade of the ore was 1.169% copper and 0.026% molybdenite.

Jan 1, 1981

By Robert A. Cummings

Disintegration of the immediate shale roof in coal mines interferes with ventilation, production, and safety. The effect is seasonal and correlates with high levels of moisture in the intake ventilation air. Disintegration, though not completely understood, is caused by shale dilation and weakening upon exposure to atmospheric moisture. Fluctuating moisture conditions are particularly deleterious, and may be at least partially controlled by "tempering" the air before it is brought to the working places. Roof behavior was studied in an operating mine during a 12-month monitoring period. This approach can be used in developing criteria to reduce or prevent shale roof deterioration.

Jan 1, 1981

By D. R. Tweeton

A modified push-pull field test and a computer model of cation exchange were developed to aid in evaluating cation exchange parameters prior to in situ mining. Reliable determination of these parameters is essential when modeling restoration of groundwater quality. The field test involves a much larger volume and much less disturbance to the ore sample than is feasible with laboratory measurements. This test can be performed in two or three weeks. It is relatively inexpensive, requiring one injection- production well and two or more wells for collecting samples of leach solution. The use of the model in interpreting test results is illustrated with field data from an in situ uranium mine. Much of the research was performed by the University of Texas at Austin, and was partially funded by the Bureau of Mines.

Jan 1, 1986

By Kefton H. Teague

An article entitled "The Rule of the Geologist in the Industrial Mineral Field" by G. R. Gullet, was published in the August, 1967, issue of the Canadian Mining Journal. Mr. Gullet defined industrial minerals as follows: "Industrial minerals are largely non-metallic minerals and rocks that find value because of their physical or chemical properties." This definition is brief, but all-inclusive. Mr. Gullet continues, "They include all useful minerals and mineral commodities except those used as fuels and those from which metals are extracted. Factors in the evaluation of an industrial mineral deposit are generally as different from those used in the evaluation of a metal deposit as is the assessment of a potential oil field. The key to the successful development of an industrial mineral, deposit is more often a balance of accessibility, transport, and proximity to markets than to any natural quality advantage of the deposit itself."

Jan 1, 1972

By R. D. Hammett

This paper describes an investigation that MS carried out using the three-dimensional, stress analysis computer program "NFOLD" to assess pillar stability in relation to existing mining conditions and the proposed layout of future stopes. The stress analyses were designed to assess the present stability of the mine (particularly the pillars adjacent to the shaft), the change in pillar stresses as mining proceeds, and the optimum stope geometry to minimize ground control problems. The existing conditions were modelled first, and rock mass strengths were adjusted until a good agreement between the predicted and observed conditions was obtained. Analyses of alternative mining layouts, based on the calibrated rock mass strengths, were then compared. The paper describes the results and the conclusions of the study.

Jan 1, 1983

By H. E. Rowen

I hope my title is not confusing; even more so that I am not. Actually pelletizing and sintering, meaning both the formation of pellets and the hardening of them, are closely related to each other and to phenomena of nature. Figure. 1 This many-celled porous structure, frozen as it was at the fusion temperature and was being frothed by fast-moving gases, may be considered a typical piece of sinter. The same structures have been found in natural ores.

Jan 1, 1962

By Donald R. Rathburn

Screening during the production of high-grade lump ore for blast furnace burden, particularly from recently developed ore deposits in Australia, South America, and Africa, has resulted in large tonnages of fine iron ore. Certain owners have decided to stockpile these fines until some later date; however, others have either sold these fines "as is" for agglomeration at the steel plant or have established their own pelletizing plants to produce a premium quality agglomerate. Normally these fines consist of the higher oxides of iron and the hydrated oxides. Unfortunately, grinding these types of materials in a wet process produces a slurry that is difficult to filter to obtain the requisite moisture level for the subsequent balling and indurating operations. The purpose of this paper is to review recent developments in fine dry grinding of iron ore and to discuss the various design and operating parameters involved. Although dry grinding of raw feed and clinker has been practiced in the cement industry for many decades, its significant application to the iron ore industry has taken place within the past ten years. Even though the basic concept of dry grinding has been borrowed from the cement industry, the successful application to iron ore grinding has not taken place without some difficulties. Consequently, the application to iron ore has required the solution of several unique design and operating problems.

Jan 1, 1970

By V. K. Karra

An improvement in the present day screen sizing methods calls for knowledge on i) how material in the size range: 0.5 x 1.5 times the through-fall opening of the mesh on a deck, splits between the oversize and undersize streams of the deck, and ii) how near-mesh content of the feed affects the screening performance. In the throughput based sizing method given here, this is accomplished through the introduction of a generalized partition curve and a near-mesh factor. A newly developed efficiency factor is employed in addition to the traditional screen sizing factors.

Jan 1, 1979

By R. P. King

Knowledge of the behaviour of flotation machines had developed and increased considerably over the last few years. Although much work remains to be done on the study of the fundamental processes that influence the collection of hydrophobic particles at an air-water interface, there is enough information to permit the building of realistic models of the gross flotation behaviour of various ores. These models serve as an ideal base for the development of simulation techniques for the steady-state behaviour of entire flotation plants that consist of a large number of individual flotation machines. Simulation techniques have a very real role to play in assisting with the design of new plants and in improving the operation of exisiting plants. Recently, highly efficient data-logging systems have been introduced on flotation plants. These systems are based on the on-line measurement of volumetric flowrate, pulp densities, and metal contents, and they generate enormous quantities of information regarding the operation of the plant. Unfortunately, this information is largely wasted at the present time because efficient data-reduction techniques, although available10 are not in common use. Simulation techniques play a central role in such data reduction because they form the essential link between the fundamental kinetic flotation processes on the one hand and the plant data on the other.

Jan 1, 1974

By Justus B. Deen

Given that the majority of mine ventilation operating costs are imposed by shafts, the need to predict the resistance of a planned shaft with reasonable accuracy is important. During conceptual design, shaft resistances are usually predicted by use of published friction factors, k, based upon lining and fitting configurations. More often than not, published friction factors do not directly coincide with "real" shafts, so their use is somewhat limited. For more accurate shaft resistance determination, equations both theoretical and empirical may be employed if there is detailed knowledge of the shaft. These equations treat the shaft resistance as discrete components, with their sum being the overall shaft resistance. This paper describes the basic shaft resistance equations and verifies these equations by comparison to field measured shaft resistances. Several shafts were examined which varied in depth, shape and fitting arrangements. Results are presented and conclusions drawn to show that the shaft resistance equations are accurate.

Jan 1, 1991

By P. Mousset-Jones

The USBH Mining Systems and Ground Control Generic Research Center funded a project leading to the improved planning of airflow and refrigeration in underground mines experiencing hot working conditions. The project was broken down into approximately five phases: 1. Visiting some of the known hot mines in the U.S. and sending out a questionnaire to determine other mines which might be experiencing hot working conditions in the future. 2. Choosing two mines in which to conduct measurements to determine the insitu rock thermal conductivity and diffusivity, and comparing these values with laboratory determined values. 3. Investigating computer programs available for mine climate simulation, and testing these programs with case study examples from the two mines where the rock thermal properties were measured. 4. Considering improved ways of estimating the wetness factor and experimenting with the use of heat flux meters to more directly measure the rock heat inflow into the airstream. 5. Applying the results of these investigations to simulating the climate for future mine development and production areas at the two- mines. The project is approximately two thirds completed. At the time of writing, the insitu measurements at one of the mines are still being recorded. This paper will be describing the procedures and results of the insitu rock thermal property measurements, and give a brief description of some of the simulated results obtained for a mechanised cut and fill stope case study from the Homestake Gold Hine in South Dakota.

Jan 1, 1985

By Martin Herenknecht, Michael Knabe, Ulrich Rehm

In Switzerland at present, the longest railway tunnels in the world, the Gotthard(57 km) and the Loetschberg base tunnel (34km) are under construction. For thischallenge six high-tech HERRENKNECHT Hard Rock Tunnel Boring Machines (TBM)are applied, which have to excavate approx. 80 km at the Gotthard and 20 km at the Loetschberg Tunnels. The machines being used are of a single Gripper-TBM type, which are equipped with the latest rock support techniques, in order to optimize the quality of the working conditions for the personnel which have direct impact on the quality of the tunnels. The different requirements of the projects based on different speci?cations within the tender documents led to completely different TBM concepts which will be reviewed in detail in this paper.

Jan 1, 2003

By Gy. Deák

The Romanian mining industry, especially salt mining, is going through a restructuring phase taking into account the Environment Acquis of the European Union1. In order to preserve the centuries-old salt mines and to develop new ones, in the same salt rock deposit, the long term stability assessment of the saline complex is very important. This case study refers to the Praid salt mine, which includes old salt mines, with impressive sizes, located above the new mines, with activity in progress, in order to provide the means and solutions for efficient conservation and sustainable exploitation for the salt resources. The DKRControl method and FLAC 3D code were used in order to assess the confidence level for the computed prediction of the stability of the salt mine complex salt.

Jan 1, 2008

By K. Yatsunami

NKK has developed a new cold bonded pellet process. The features of this process are; 1) it is a continuous process with 10 hours curing. 2) Products can be used as materials for various metallurgical furnaces. 3) Various kinds of slag are used as binders if necessary. 4) The quality of products is excellent. The pilot plant completed in 1981 is now being successfully operated. We are also constructing a commercial plant at our Niigata works. We produced cold pellets containing carbon as material for ferroalloys (Si-Mn), by pilot plant and used them in furnaces. Consequently, considerable economic advantages were obtained.

Jan 1, 1984

By Everett M. (Original by) White

Numerous articles have been written about the coal mine ; he has been compared with brave men who have gone out to conquer some unknown hazard throughout the ages. Now, however, modern mining is no longer something to be avoided, but a vocation that anyone can be proud of, with remuneration equal to or above that of almost any industry. A concerted effort is being made each day by both the operators of most mines as well as the state and federal inspectors to see that coal mines are as safe or safer than work places in any other industry. How- ever, it is true that mine fires and explosions have occurred in the mining industry since its inception. One of the earliest accurate references to such an occurrence is found in the transactions of the Royal Society of London. In the Colliery Managers' Handbook, 1898, Caleb Pamely writes of an explosion that occurred at Fatfield, England in August 1708, resulting in the deaths of 69 persons. He states: "Three of them, viz, two men and a woman, were blown quite up from the bottom of the shaft, fifty-seven fathoms deep, into the air, to a considerable distance from the mouth of the pit." It is interesting to note that women were employed as miners in England during that period. In the United States, the first record of coal mined was in 1702 by the Jamestown colonists. In 1786, about 20 years after Pittsburgh, PA was first settled, a charter was granted by William Penn to mine coal on the banks of the Monongahela River. Then in 1803, the first important coal company, the Lehigh Coal Co., was established. From this beginning, the mining industry continued to grow in importance and the first state mining law was formulated in 1870. The Pennsylvania state mining law was followed in 1873 by Ohio's, and in 1876 by Maryland's. A mine explosion at Avondale, PA in 1869 stimulated state legislatures to formulate these early laws. In 1907 near the town of Fairmont, WV, there were, within three days, two explosions resulting in a total of 597 deaths. Because of this, the federal government took action and by 1910, the US Bureau of Mines had been established. This was perhaps the most significant change in health and safety for miners during the first half of the 20th century as the USBM concentrated its entire efforts in the study, research, and testing of methods totally directed towards improvement of the health and safety of the miner. After a mine disaster in Illinois, a federal law was passed in 1940 calling for federal coal mine inspectors. Then in 1969, Congress enacted the Federal Coal Mine Health and Safety Act following a mine explosion near Farmington, WV. In 1977, the law was revised and included noncoal mining operations.

Jan 1, 1981

By Gerald C. Smith

Carlin Gold Mining Company is a wholly owned subsidiary of Newmont Mining Corporation and is located 76 kilometers north west of Elko, Nevada. Multiple bench open pit mining methods are being used to mine 24.5 Mt of ore and waste per year. Mining started in 1964 and up through 1983 Carlin has mined 138 Mt of ore and waste and has milled 13.8 Mt of ore. Selective mining of carbonaceous and oxide ores together with a good grade control program have been key factors in the success of the operation. This paper will present the raining methods and the mining equipment being utilized to make Carlin Gold Mining Company a very profitable operation while mining and milling low-grade gold ore.

Jan 1, 1985

By J. N. Albright

Both microgravimetry and crosshole seismic tomography are means by which subsurface collapse and rock failure may be observed. We show results of calculations that predict changes in gravity and gravity gradient that result from void migration, bulking, and hydrology disruption due to room and pillar mining. Crosshole seismic tomography also holds promise for detecting and mapping changes in structure during subsidence. Commercially avail- able logging tools, advances in theory, and recent field results strongly suggest tomographic surveys are now possible. Subsidence phenomena which may be located are faulting, joint separation, bed parting, water table changes, and formation outgassing.

Jan 1, 1982