Search Documents

The concept of "classification is expanded beyond the performance of the classifying equipment to include all aspects of the fines removal system of the grinding circuit. Design and operating parameters which affect fines removal are identified and discussed, and a quantitative index for circuit fines removal effectiveness is defined. This approach lends new interpretation to certain observed phenomena, and suggests useful guidelines for circuit design and operation.

Jan 1, 1985

By Eugene C. Robertson

The exchange of heat from wall rock to ventilating air was studied in a cross-cut driven through fresh rock on the 4600 level of the Kelley Mine, Six- teen thermocouple probes, 10 inches long, twenty-three probes, 7 feet long, and five probes, 50 feet long, were emplaced in the walls soon after blasting and wall -rock temperatures were monitored intermittently over a two-year period to determine heat loss from the wall rock. Temperatures, humidity, and velocity measurements were made of the air at the same times to determine heat gain. An important but less well-defined variable was the heat transfer by water entering the crosscut from fractures and leaving in the ditch. The balance of heat in and heat out at each probe station is within an acceptable range. Theoretical and empirical models for heat flux into a cylindrical opening fit the data reasonably well, also.

Jan 1, 1970

By Robert D. Coale

This paper will describe the copper concentrate slurry pipeline and pumping system between the concentrator and the port at Bougainville Copper Ltd. The operations of Bougainville Copper Ltd. are located on the island of Bougainville in the South Pacific. Geographically, it is the northernmost island of the Solomon Group but, politically, it is part of Papua New Guinea. Papua New Guinea is a United Nations Trust territory administered by Australia, having recently been given self-government, with independence scheduled for December 1974. (Fig. 1). The island is approximately 130 miles long by 30 miles wide, with the Crown Prince mountain range forming a spine along its length. The mountains in place are over 8,000 feet high with the mine located on the western flank at an elevation of 2,200 feet. Exploration on Bougainville for copper by Conzinc Riotinto of Australia (CRA) began in 1963 and by 1968, through geophysical, geochemical and diamond drilling methods, an orebody containing nearly one billion tons of ore grading approximately 0.48% Cu. and sane gold had been outlined. Bougainville Copper Ltd., the company operating the mine, is 53.6% wined by CRA, 20% mined by the government of Papua New Guinea with the public Folding the remainder of the shares. The first copper concentrate was produced in early 1972, with production for the first full year, 1973 being:

Jan 1, 1974

By H. W. Gao

During the last decade, the feasibility of applying the in situ leaching technology to the recovery of copper from deeply buried deposits containing chalcopyrite has received much attention.(1-4) The major incentive for using this technology is that under certain circumstances, copper in deep underground deposits, which cannot be mined economically by conventional means, can be recovered economically. Basically, this technology involves rubblization of the deeply buried copper ore body followed by in-place leaching of the rubblized copper ores. Rubblization of the ore can be achieved by some suitable method such as the use of block caving mining. The rubblized chimney is then filled with water until the original water level is reached. Leaching occurs when the eater saturated with oxygen is introduced into the chimney- and flows through the fractured rock masses and within pores of rocks. As the dissolved oxygen oxidizes the primary sulfides, heat is generated. Because of low conductivity of the surrounding rocks, the generated heat is able to raise the temperature of the chimney. The increase in the temperature of the chimney and the relatively high content of dissolved oxygen in the leach solution under high hydrostatic pressure will result in an enhanced dissolution of the primary sulfide minerals. To ensure a successful application of the in situ leaching technology, a complete understanding of the effects of the ore particle size distribution, ore grade mineralogy, temperature, pressure, lixiviant concentration, pH, etc. on the rate of copper recovery is necessary so that copper can be recovered efficiently and the amount of copper extracted can be predicted. These can be achieved through mathematical modeling of the in situ leaching process and conducting laboratory tests. In this paper we will present a mathematical model that simulates the in situ leaching process as depicted in Figure 1. To model this process properly, not only the 'kinetic and thermodynamic aspects of leaching chemistry must be known, but the effects of heat generation, the physical aspect of fluid flow and other related multicomponent transport phenomena must be considered. Furthermore, since most factors involved in the leaching process change with time, a leaching system must be described using unsteady state equations.

Jan 1, 1981

By Nord L. Gale

The discovery of important new ore deposits of lead, zinc, copper and silver in 1955 in Southeastern Missouri has resulted in the development of a thriving mineral industry known as the "New Lead Belt" or "Viburnum Trend", to distinguish it from the older lead producing areas to the East. This region has recently become the world's largest lead producing district with production in 1970 reaching 432,576 tons or 74.4% of the entire United States lead mine production. The area is heavily forested with rolling hills dotted with numerous clear running streams in the Clark National Forest of the Missouri Ozarks. The location is within 70 miles of St. Louis, Missouri and has a natural abundance of water resources which provide an important recreational area for fishing, hunting, camping and other outdoor activities. Until this recent development, the area was sparsely populated and industrialization was almost unknown. The infusion of $150 million in mining capital has brought about a dramatic change in the economic structure of the area and will almost surely be accompanied by changes in its environmental picture. In an effort to maintain this bountiful national resource and to evaluate the changes occurring in surface water quality and aquatic life forms present, an inter- disciplinary research program at the University of Missouri has been undertaken with the support of the National Science Foundation. Research has been carried out to determine background values, establish natural baselines, and to evaluate the extent and causes of changes in streams effected by mine water discharges and wastewater from ore milling operations. The unique topography of the "New Lead Belt" area allows the channelization of milling and smelter wastes to separate stream systems (Figure No. 1) thus allowing measurements of the pollutional effects on an individual basis.

Jan 1, 1973

By S. S. Peng

The generation and transportation of the airborne dust are mainly governed by the velocity and the movement pattern of the ventilation air in the longwall face. Generally speaking, the higher the air velocity, the more the airborne dust will be generated and the longer the period of the dust of certain size will be carried away from the source. In order to effectively prevent the production and the spread of the airborne dust, The airborne dust concentration distribution in the longwall face must be known in advance. Before the dust concentration distribution can he predicted theoretically with confidence, the air velocity distribution pattern of the ventilation air in the longwall face area must be determined first. However, the complicated, time-dependent and unpredictable mining conditions along and around the face area make the theoretical studies of the problem rather difficult. For instance, one of the factors commonly affecting the air velocity distribution at the longwall face is the air leakage, either into or from the gob area. The leakage quantity and the location of occurrence differ from mine to mine, face to face, and time to time. They depend not only on the compactness of the caved roof fragments in the gob, but also on the degree of obstructions in the working space and in the return entry. Another obstacle to the theoretical studies about the velocity distrbution is the complicated boundary conditions of the ventilated spnce which is very difficult to represent accurately in mathematical forms. In this paper, the air velocity distributions measured in four longwall faces are presented. A statistical model for each longwall face is also derived for prediction of air velocity distribution in the longwall face.

Jan 1, 1985

By H. Weber

This paper is in three parts. Part I discusses the various types of cement clinker coolers now in full-scale operation. Part II is a detailed study of the criteria for selection of the type of cement clinker cooler best suited for a given installation. Part III covers a number of cooling problems and their solutions in some of the metals industries. The large and world-wide problem of cement clinker cooling has motivated much study and development and the coverage here of this work is somewhat detailed. In contrast the cooling problems of the metals industries are quite varied between industries and often quite different from plant to plant in the same industry because of basic differences in the requirements of the particular material being processed. Therefore the coverage of metals industries coolers is somewhat more general. It is believed that all of the technology covered here may be of interest to those working with the problems of cooling hot materials.

Jan 1, 1980

By R. K. Singhal

Optimization of a load-haul system for a surface mine involves two processes. The first is proper selection of mining equipment compatible with the minesite job specifications and the second is an efficient utilization of this equipment. All things being equal optimal productivity and cost is achieved when the capacity of the hauling equipment is matched at all times with that of the loading equipment.

Jan 1, 1986

By James J. Brady, Kenneth L. Faught, Chadi El Mohtar, Chaoshi Hu

"During construction of a 9.5-ft. diameter sanitary sewer tunnel, the City of Edmonton encountered a large pocket of flowing sand that flooded their TBM and caused significant surface subsidence, stopping further tunneling by the TBM through this zone. A unique collaborative effort ensued between the authors representing the city, consulting engineers and academic researchers to develop the optimal strategy for grouting the problematic soils. The site has a layer of very find sand between 20 and 30 ft. in depth with fines contents ranging from 5% to more than 40%. The collaboration extended from requesting additional site investigation efforts to shipping samples to the UT-Austin laboratories for grout testing plus ground and grouting characterization tests resulting in field recommendations for a full scale ground improvement program. New research information on the grouting of fine sands along with a collaborative framework for the design of in-situ grouting projects are the key topics presented. INTRODUCTION Encountering a large unexpected pocket of flowing sand with an open-faced TBM while excavating a tunnel below the groundwater table is never a good thing. This was certainly true for the City of Edmonton when one of their Lovat TBM’s became inundated by flowing sand while excavating the 9.5-ft. diameter Millwoods Double Barrel Replacement Tunnel in September 2013. However, since the City of Edmonton self-performed this work, a rare situation existed where the site could be investigated objectively, without the prejudice of contending parties selectively influencing how information was gathered and presented, to accurately examine site conditions with a goal of identifying the best remediation measures."

Jan 1, 2016

By A. T. Yu

The broken hill proprietary company Ltd., Australia's only steel producer, has come a long way. Since 1885 to reach today's. Capacity of 6.6 million long tons of ingot steel per year.* its Newcastle steel complex in New South Wales, located 100 miles north of Sydney and on-stream since 1915, has likewise shown continued impressive growth (fig. 1). The most recent expansion plans at Newcastle call for sub¬stantially increasing its production, with the help of some added facilities, but principally relying on the increase in efficiency of the furnace operation. Its modern raw materials blending system will playa major role in meeting Newcastle's new targets.

Jan 1, 1969

By D. W. Frommer

Processing nonmagnetic taconites by selective flocculation-desliming and flotation requires large volumes of water. If impounded without treatment these off-process waters require excessively large areas for containment. To discharge the waste water into natural waterways would contribute to stream pollution and likely would not be permitted. In Bureau of Mines experiments conducted in the Twin Cities Metallurgy Research Center&apos;s 900-lb/hr pilot plant, approximately 85 percent of water requirements for the flotation-based treatment of a Michigan nonmagnetic taconite were met by reclaimed water. Water reclamation of the off-process streams from flotation was accomplished by controlled additions of lime, sodium carbonate, and a synthetic flocculant to reduce turbidities to <1,000 ppm equivalent Si02, while maintaining a Ca(II) content of 516 ppm in the finished effluent. Flotation concentrates of good quality were obtained using the reclaimed water. The cost of chemicals used in water reclamation was approximately equal to the savings in flotation reagents attributed to recycling of the water.

Jan 1, 1970

By I. Papadopoulos

Nowadays, geophysical prospecting is implemented in order to resolve a diversity of geological, hydrogeological and geotechnical problems. Though plenty of applications and a lot of research have been conducted in the country-side, only a few have been reported in the literature concerning urban areas, mainly due to high levels of noise present that aggravate most of the geophysical methods (e.g. electromagnetic, seismic, gravity etc.) or due to spatial limitations that hinder normal method implementation (e.g. electrical). Among all geophysical methods, electrical tomography proves to be the most rapid and urban noise insusceptible technique. This work presents a case study in the urban area of Hania (Crete I., Greece), where Electrical Resistivity Tomographies (ERTs) have been carried out for the detection and identification of possible buried ancient ruins or other manmade structures, prior the foundation of a building. Nineteen profiles were surveyed in a 20x40m grid using dipole-dipole configuration. The results indicate two areas of interest, that are interpreted as probable old wells, in the context of the existence, in former times and in the same area, of an olive oil plant. In the vicinity, near surface ancient ruins have been disclosed, but no such evidence provided this survey, for the particular area under study and the prospected depth. The collected ERT-data were processed by applying advanced algorithms in order to obtain a 3D-model of the study area that depicts more clearly and accurately the interesting subsurface structures.

Jan 1, 2005

By George K. McCord

It is a pleasure to participate in this Fall meeting of the Society of Mining Engineers to discuss energy conservation trends in the cement industry. Energy is the "life blood" of American industry, and the ability to use available energy resources efficiently may well determine the future of our nation and of its industries. The Federal Energy Administration has classified cement manufacture as one of several energy-intensive industries in the U.S. and has selected the Portland Cement Association to make a detailed study of possible energy conservation measures. Member companies of the Portland Cement Association represent about 85% of the cement producing capacity of the United States and 100% of Canadian capacity. Stated briefly, the purpose of the Association is to extend the uses of portland cement and concrete through research and development, market promotion, education, and public affairs work. PCA&apos;s general offices and research laboratories are located in Skokie, Illinois. Our staff of engineers, scientists, and research personnel make the PCA uniquely qualified to perform an energy conservation study of the kind requested by FEA.

Jan 1, 1975

By Roberto de Moraes

Lunar construction faces unique challenges arising from the nature of regolith and megaregolith. Unlike terrestrial soils shaped by weathering, lunar regolith is composed of angular, poorly sorted particles produced by impacts, with bulk Density, strength, and trafficability varying sharply with depth and terrain. Boulder fields, floaters, and talus aprons add further complexity, disrupting excavation and mobility. Apollo missions documented these conditions through drive-tube samples, trenching, penetrometer data, trafficability tests, and seismic profiling, but the results remained as datasets rather than a unifying classification. This paper introduces the LRC (Lunar Regolith Classification) Framework and the Overconsolidation Ratio applied for the Moon (OCR*), the first contractor-ready system to organize Apollo-derived trends into excavation demand zones (L1–L5). LRC is explicitly a classification, not a stratigraphy: depth ranges are indicative and require in-situ verification before use. Each zone is defined by bulk density and strength ranges, field proxies (bootprints, trench stability, auger torque, seismic contrasts), and corresponding excavation implications. Worked examples from Apollo 15 (mare), Apollo 16 (highlands), and Apollo 17 (pyroclastics and talus) demonstrate how observed data translate into LRC zones. These cases show that LRC captures both systematic depth trends and sharp local heterogeneity. The framework standardizes excavation planning for landing pads, haul roads, berms, foundations, and tunneling trials, while converting floaters from hazards into resources. LRC thus provides a common language for lunar construction. Rooted in Apollo evidence but designed for Artemis verification, it is proposed as a living standard; a reference framework to guide site preparation, excavation, and risk management in the next phase of lunar development.

Feb 22, 2026

By L. J. Buchanan

The relationship between hydrothermal ore deposits and hot spring systems has received intensive study in recent years, particularly as a consequence of interest in the energy potential of geothermal systems. Base and precious metal deposition in surface pools and at shallow depths in modern geothermal systems has been recorded in numerous publications (1, 2, 3) Theoretical studies of hydrothermal fluid flow at depth, connected to surficial hot springs systems, have been presented by White and others (1), Cathles (2) , Henley and McNabb (3). As a result of these and additional studies, numerous hydrothermal ore deposits are thought to have originated as genetic parts of larger geothermal systems. In particular, it appears that metal precipitation is greatly enhanced in zones of boiling where volatiles and steam are escaping (4). High grade, near surface concentrations of base and precious metals, deposited as a result of partial vaporization of rising fluids, are such a common aspect of modern not spring systems that ore deposition models are becoming based on what may be called a geothermal model. In its most general terms, this model requires an anomalously high thermal gradient which acts as the driving force behind a convecting hydrothermal system. The water may be entirely meteoric or may be In part at least of other origins. The water migrates towards the higher temperature area, becomes heated, and picks up alkalies and metals by dissolving minerals along the fluid path. As water exits to the surface above the heat source, a mass balance requires the incoming hot water to rise to replace the lost water. As the water rises past the elevation where the hydrostatic pressure is insufficient to prevent boiling, then boiling will occur. Depending on the salinity and the temperature of the water, boiling can occur anywhere from great depths to near surface. Boiling results in a loss of volatiles, a pH rise in the fluid phase, cooling of the remaining fluid, a rise in oxygen fugacity, a concentration of salts in the remaining liquid, and precipitation of ore and gangue minerals.

Jan 1, 1980

By James M. Barker

The occurrence of borates and zeolites at Mesa del Alamo is well documented by McAnulty and Hoffer (1) and Lefond and Barker (2). Further investigation indicates the presence of priceite and meyerhofferite in addition to the howlite (1) and colemanite (2). Analcime occurs in addition to the clinoptilolite and phillipsite (2). The Mesa del Alamo area is about 200 !a south of Tucson, Arizona, and 13 km southeast of Magdalena, Sonora, Mexico, just south of the unpaved road to Cucurpe (Figure 1). The geology and mineralogy of northcentral Sonora is known only on a regional basis except for small areas mapped in detail during copper exploration. The study area is within the Basin and Range province of North America from which borates and zeolites are now produced in California. The borates and zeolites at Mesa del Alamo occur in geological environments similar to those of the Mojave and Death Valley regions of California (3, 4). Thus, a detailed exploration pro- gram in the Magdalena area could result in the discovery of economic borate and/or zeolite deposits.

Jan 1, 1979

By Keshavan Nair

In connection with Project Payette, which is concerned with the detection of underground nuclear explosions, it was necessary to determine the technical feasibility of constructing and maintaining a large (approximately 315 feet in diameter) unsupported underground cavity at a depth of approximately 2700 feet in the Tatum Salt Dome in Mississippi. The dimensions and the location of the cavity in the salt dome were governed by criteria laid down by the Atomic Energy Commission. Within the framework of the specified criteria, cavities of various shapes and dimensions could be utilized. One aspect of the feasibility study was to investigate the structural stability of various cavity shapes and to recommend a preferred shape. This paper summarizes the studies that were conducted to evaluate the structural stability of various proposed cavities.(l)

Jan 1, 1968

By R. H. Olson

Pigments are used in two segments of papermaking, as the major component in paper coating formulations and, in small percentages, as fillers in the paper web. Historically, the dominant use has been in coating, however, recent developments have fostered a multifaceted effort to substantially increase the pigment component in the paper furnish. Factors responsible for these developments together with their relationship to recent and forecast changes in papermaking technology are reviewed. Finally, some thoughts are presented on the probable timing and extent of these changes as well as their expected impact on the future demand for the common paper pigments.

Jan 1, 1985

By R. A. Williams

Surface and electrochemical techniques have been used to describe the surface chemistry of ferrosilicon powders, as a function of pH and electrochemical potential, for conditions typical of operating DHS plants. The practical consequences on the likely corrosion behaviour and associated electro- kinetic particle-particle interactions (which affect stability to sedimentation) in the suspension, are discussed.

Jan 1, 1987

By George Vranesh

Synfuels development in the upper Colorado River basin and the population growth attendant with such development demand sizeable quantities of water. Unfortunately, the water supply in the basin is limited and such limitation may impose a significant constraint on the development of the West&apos;s abundant energy resources. Although the water for the synfuels development will be governed by the law of prior appropriation adopted in the upper basin states, the authors point out that an apparently senior water right .my not deliver a firm supply of water. The federal and Indian Reserved Water Rights Doctrine, the Colorado River Compacts the Doctrine of Equitable Apportionment, and the federal and state environmental laws can all severely diminish the value of any given water right and the synfuels industry should take care to evaluate these factors in acquiring its water.

Jan 1, 1981