Search Documents

By F. Calizaya

A booster fan is an underground fan installed in series with a main surface fan and used to boost the air pressure of the ventilation air passing through it. To accomplish this objective, the fan is installed in a permanent stopping and equipped with airlock doors, a monitoring system, and interlocking devices between main and booster fan controls. The stopping and doors are used to prevent flow recirculation, and the monitors to ensure safe operation of the fan. A booster fan, properly sized and sited, can be used to create safe work conditions and allow the extraction of minerals from areas that would otherwise be uneconomic to mine. In deep and large mines with heavy emissions of air contaminants, the required quantities of air can only be supplied by using high pressure fans. These fans will inevitably induce significant losses of fresh airflow through the stoppings and doors. For well defined ventilation circuits, booster fans can be used to decrease the main fan pressures and reduce the leakage flows. However, this will require a good understanding of the correct ventilation practice, from planning to operation and maintenance of booster fans. The objective of this study is to investigate the conditions under which booster fans can be used safely and efficiently in underground coal mines. Specifically, the study is directed at (1) collecting reliable information on airway resistances and flow requirements from two large U.S coal mines, (2) collecting fan performance data from one or more existing coal mine where booster fans are used regularly, (3) monitoring the performance of booster fans in a laboratory model and an experimental mine, (4) developing a booster fan selection method to assist the ventilation engineer at the planning stage, and (5) training six M.S. or Ph.D. graduate students in advanced mine ventilation.

Jan 1, 2010

By Jock McGregor, Deepak Malhotra, Leonard Harris

After more than 100 years, alkaline cyanide leaching of gold and silver ores, either directly in the case of oxidized ores, or after pretreatment of refractory ores by roasting, pres­sure leaching or bacterial leaching, remains the dominant r leaching method to extract the precious metals f om ores. Leaching with halides (chlorine, bromine and iodine) and with thiourea and thiosulfates is less common but prac­ticed in some cases to dissolve the precious metals both from ores and jewelry and electronic scrap. Cyanide solutions can contain from 1 ppm Au to 30,000 ppm Au. According to the source, i.e., agitated tank leach­ing, heap leaching, eluates from stripping activated carbon or waste electroplating solutions. Similar variations occur with silver which can have a profound influence on the recovery method. The presence of other elements in the leach solu­tions, particularly mercury and copper, likewise play an important role in the procedures required to recover the gold r and silver values f om solution. The same circumstances are found when lixivants other than cyanide are used to dissolve the precious metals. For decades, the preferred method of recovering gold and silver values from alkaline cyanide leach solutions was by zinc dust precipitation according to the Merrill Crowe process developed in the late 19th century. Finely ground gold and silver ores or concentrates were either leached directly or after roasting, in agitated tanks or Pachucas and subjected to solid/liquid separation by filtering or by treat­ment in counter-current-decantation washing thickeners (CCD). This solid/liquid separation step was often very dif­ficult especially when ores containing high quantities of clay were treated which caused filtration or thickening problems. Following testing and development by the U.S. Bureau of Mines (USBM) in the late 60s, the introduction of carbon­in-leach (CIL) or carbon-in-pulp (CIP) plants to recover gold and silver from leach pulps was one of the greatest opera­tional and cost saving improvements made in the industry in South Dakota and quickly spread around the world to be the most common process to recover gold and silver from cyanide solutions.

Jan 1, 2000

By W. W. Roberts

Key elements to the successful excavation and support of the Forest Glen Station and Tunnels for the Washington Area Metropolitan Transit Authority are discussed. Excavations encompassed a twin-vault station; 2339.3 m (7675 feet) of conventional drill and shoot tunnel; and 810.8 m (2660 feet) of mixed faced tunnel. The use of dewatering, boom type continuous miner and shotcrete in the mixed faced tunnel, along with hydraulic drills, bolts, and shotcrete in the rock tunnels and station proved to be effective methods.

Jan 1, 1983

By A. L. Miller, A. J. Chambers, P. R. Griffiths, D. A. Parks

"Diesel engines are one of the primary contributors to the presence of nano and ultrafine aerosols in ambient air and occupational environments. Exposure to diesel emissions has been shown to contribute to various adverse health outcomes of the pulmonary system and cardiovascular system. Currently diesel emissions in the workplace are monitored by way of collecting the aerosol onto filters, which are then sent to a lab for thermal-optical analysis using the NIOSH 5040 method, which measures elemental and organic carbon explicitly. This process can take days or even weeks, and workers can potentially be exposed to excessive levels of diesel particulate matter (DPM) before the problem is identified. To remedy this, researchers from the National Institute for Occupational Safety and Health (NIOSH) are seeking to develop a field-portable method for measuring elemental and organic carbon in DPM aerosols. In the current study, we investigated the use of Fourier transform mid-infrared (FT-IR) spectrometry, which lends itself more readily to implementation in a real-time system than do the thermal-optical analysis methods. We have demonstrated a method for measuring organic and elemental carbon in DPM for a broad range of organic carbon (OC) to elemental carbon (EC) ratios (from 50.3 to 0.8). The ability to handle a wide range of OC to EC ratios is critical given the evolving diesel technology. INTRODUCTION Respiratory illnesses are common in mining industry workers [1] and exposures to toxic aerosols such as DPM can result in serious respiratory illness [2]. Health studies show a correlation between workplace exposure to diesel exhaust and an increased risk of lung cancer [3-8]. The International Agency for Research on Cancer (IARC) has characterized diesel exhaust as a human carcinogen [9], and similar classifications have been made by the World Health Organization and the California Air Resource Board. A recent study [10] suggests that the risk of lung cancer is approximately three times greater for heavily exposed workers. When compared to other aerosols in the mine environment, the settling time of DPM is significantly longer than that of dust due to their small particle size (typically < 1 µm) [11]. Additionally, submicron particles (such as DPM) are deposited in the lungs much more efficiently than their larger counterparts such as dust [12]. Previous studies focusing on particle morphology [13] show that the largest mass contributor to lung disease in mining is elemental carbon, which provides a solid core onto which hydrocarbons are adsorbed. In accord with those findings the Mine Safety and Health Administration (MSHA) decided on submicron total carbon as a surrogate for monitoring diesel particulate matter in the mining environment."

Jan 1, 2018

By D. A. Rice

In pelletizing magnetic iron ore concentrates, about 6 to 18 lb of bentonite binder are added per ton of concentrate during balling to give green and dry strengths to the unfired pellets. The dry bentonite is mixed into the filtercake following the magnetic concentration circuit of the plant. The filtercake contains about 10% moisture, and the water may be of highly variable composition, depending on the particular concentration circuit, its source, and the ore being treated. A knowledge of the parameters that influence the balling operation is essential for optimal efficiency in producing balls strong enough to survive the treatment during transportation from the balling device to the furnace and during the firing operation. Furthermore, very weak unfired pellets probably contribute to high dust losses and poor furnace control. The factors that determine the strength of unfired pellets have received considerable study (1,2,3,4). Tigerschiold and Ilmoni(l) pointed out the significance of the surface area of the particles being pelletized. Merklin and Childs(2) reported on the effect of material size consist, chemical additives such as soda ash, lime, balling time, ball size, and the moisture content of green balls. Iwasaki and Zetterstrom(3) examined the detrimental effects of fatty acids on the pelletizing process. Stone(4) correlated the zeta potential of bentonites with the strength of unfired pellets. He found that, in general, a high negative charge on the bentonite is conducive to good balling. Although studies of pelletizing in the iron ore industry deal with a complex multicomponent system consisting mainly of the iron mineral, bentonite, and water, the last of these has received little attention, particularly with regard to the possible effects of mill water chemistry on the pelletizing process and the strength of unfired pellets. It is widely known that the composition of mill process water is an important variable in unit operations such as flotation, thickening, and filtering and that impure water can lead to poor metallurgical results. The results of the present study indicate that the chemistry of the mill water may be an important variable in the balling operation as well. Knowledge about this variable should contribute to lowering bentonite and oil consumption and to improving furnace performance. Such knowledge can also assist those who use balling in evaluating commercial bentonites for plant use as well as those investigating balling from a more fundamental point of view In this study we have examined 1) the effects of replacing mill process water in the magnetic concentrate filtercake with pure water, and 2) the effects of several chemical impurities that are commonly found in mill process waters upon the strength of unfired pellets. The results are interpreted in terms of the zeta potential of the bentonite and magnetite particles. The data lend support to a suggested mechanism whereby the electrostatic attraction of oppositely charged particle surfaces causes bentonite-bentonite and magnetite-bentonite bonding. This mechanism would also explain why several chemical additives e.g., sodium carbonates and phosphates, have such marked effects on increasing the strength of unfired pellets.

Jan 1, 1971

By Samara Ali-Ahmad, Keith Hanks, Cindy Pham

The City of Los Angeles will rehabilitate approximately 9 miles of its North Outfall Sewer. This sewer was constructed in the 1920s as an unreinforced concrete semi-elliptical sewer. One of the methods for rehabilitation is to approach the sewer as a pre-excavated tunnel and install pre-cast segmental liners to provide a single pass corrosion resistant, structurally self sufficient project. The estimated cost for this project is $46 million. The project has completed the pre-design study, and the design is now underway.

Jan 1, 2003

By P. T. Bissert, L. Yan, M. D. Klein

"Federal regulations require the installation of refuge alternatives (RAs) in underground coal mines. Mobile RAs have a limited ability to dissipate heat, and heat buildup can lead to a life-threatening condition as the RA internal air temperature and relative humidity increase. The National Institute for Occupational Safety and Health Office of Mine Safety and Health Research performed heat testing on a 10-person tent-type training RA and contracted ThermoAnalytics, Inc. to develop a validated thermal simulation model (TSM) of the tested RA. The TSM was used to examine the effects of the constant mine strata temperature assumption, initial mine air temperature (MAT), initial mine strata surface temperature (MSST), initial mine strata temperature at depth (MSTD), and mine strata thermal behavior on RA internal air temperature using 117 W of sensible heat input per simulated miner. For the studied RA, when the mine strata temperature was treated as a constant, the final predicted RA internal air temperature was 12.8°F lower than it was when the mine strata thermal behavior was included in the model. A 10°F increase in the initial MSST resulted in a 7.1°F increase in the final RA internal air temperature, whereas a 10°F increase in the initial MSTD yielded a 2.5°F increase in the final RA internal air temperature. INTRODUCTION Since 2008, the Mine Safety and Health Administration (MSHA) has required the installation of refuge alternatives (RAs) in underground coal mines (1). MSHA requires that RAs provide an environment with breathable air for entrapped miners for a 96-hour period. Heat buildup inside an occupied RA is a serious concern. Without a means to dissipate the heat and humidity generated by the occupants and the carbon dioxide scrubbing system, the temperature and humidity inside RAs could lead to severe discomfort or heat stress depending on the mine ambient temperature before and during occupation of the RA. NIOSH recommended an apparent temperature limit of 95°F in its 2007 report to Congress (2). In 30 CFR 7.504, MSHA has specified a maximum apparent temperature of 95°F inside an occupied RA (3). The apparent temperature is calculated using both air temperature and relative humidity (4). Calculations could be used to determine if the air within an occupied RA will reach the apparent temperature limit. In these calculations, in order to simplify the problem, the mine temperature could be assumed to remain constant. With this assumption, the effects of the mine strata thermal mass and thermal conductivity on the heat buildup in an RA are ignored. OMSHR research has shown that the mine air and strata temperatures surrounding an RA increase when subjected to the heat of an occupied RA (5). Thus, calculations performed with the assumption that the mine temperature is constant would under-predict the resulting dry-bulb temperature and apparent temperature for a given RA occupancy. The mine air temperature has been used as the basis for RA temperature calculations. However, research has not been used to confirm that the mine air temperature is the appropriate basis."

Jan 1, 2016

By Ehsan Alavi, Sanjeer Yogendran, Savreet Singh

The Don River & Central Waterfront Coxwell Sanitary Bypass Tunnel Project in Toronto extends approximately 10.5 km from Ashbridges Bay Treatment Plant west under Lake Shore Boulevard, north under Bayview Avenue and east through the Don River park area to the Coxwell Ravine Park. This project includes the installation of five intake shafts connected by 10.5 km of 6.3 m internal diameter tunnel and eleven drop shafts and vent shafts, connected to the tunnel by a series of adits. During the excavation of one of five intake shafts (20 m in diameter and 52 m deep), significant volumes of free phase oil and hydrocarbons were encountered. Due to the heavy inflows of the contaminants, excavation was stopped at the transition depth. The initial support of excavation needed to be redesigned, shaft had to be backfilled with CDF and installation of deeper secant piles are in progress to cut off contaminants. This paper outlines the initial plan for excavation as well as the design changes to the plan. The current status of the shaft excavation and lessons learned will be discussed.

Jun 13, 2021

By A. R. Laplante

A test to determine the amount of gravity recoverable gold (GRG) in an ore is described. Typical GRG results are given; an error analysis is detailed; possible uses are discussed. Of the 38 samples tested, the lowest GRG content was found to be 25% (most below 25 11m, or 600 mesh), and the highest 94% (most above 300 11m, or 50 mesh). The average GRG content was 63%, with a standard deviation of 19%. Error analysis shows the test to be reproducible within 5 to 10%, depending on the size distribution and grade of GRG, and the sample extraction protocol. When using the same primary sample, reproducibility improves, 2 to 5%, depending on the amount of gold coarser than 850 11m (20 mesh) and sample weight. The test has been applied to greenfield project and retrofit applications, to determine the suitability of gravity recovery. For existing circuits, it has been coupled with a model of gravity recovery for optimization studies.

Jan 1, 1996

By Ora H. Rostad

The sequence of events preceeding the discovery of the Mount Emmons molybdenite include some inadvertent near misses by several groups. The events are given in general chronological order to bring out the essentially contemporaneous, but different activities by several groups in two areas on opposite sides of Mount Emmons. The Mount Emmons molybdenite deposit lies in the Elk Mountain mining district. The west edge of the deposit is near the boundary between the Elk Mountain and Ruby mining districts as shown by the USGS map included (see Fig. 1). Considerable history regarding the Keystone silver-lead-zinc mine is given because of its proximity to the Mount Emmons molybdenite deposit which is on the other side of the mountain from Redwell Basin and where other significant activities took place. It should be noted that there was no documentary evidence available to me that would indicate that molybdenite was recognized to be present on, or under, any part of Mount Emmons, including Redwell Basin, before 1970. Veins containing silver-lead-zinc minerals were discovered in the Elk Mountain and Ruby mining districts about 1872. Some discoveries on the south flank of Mount Emmons about 1880 were developed into the Keystone mine. The Keystone has the largest cumulative production of metal ores of any of the mines in these districts. Most of the 413 Mt (455,473 st) of ore produced from the Keystone mine through August 1967 was produced after 1950. The ore averaged 175.4 gt (5.64 oz per ton) Ag, 2.62% Pb, 5.56% Zn, and 0.72% Cu.

Jan 1, 1991

By T. Negeri, A. O. Orumwense

Microwave pretreatment is one of the emerging technologies which have been reported as having potential economic benefits for the processing of amenable ores. The application of microwave pretreatment to the processing of refractory and finely disseminated ores is of great interest as the technology can potentially reduce high comminution costs and improve mineral liberation. Sized ore samples were subjected to microwave irradiation at power levels varying from 1 to 5 kW over exposure times of between 1 and 6minutes in order to determine the influence of heating rate on mineral transformation, ground product size distribution and mineral liberation. The microwave irradiated samples were ground and subsequently floated. A comparison is made with non-microwave treated samples. Flotation grade and recovery show a strong dependence on the microwave absorption characteristics of the mineral components of the ore, in the following decreasing order -sphalerite, galena, and lastly chalcopyrite.

Jan 1, 2003

By J. E. Murphy, Y. Topkaya, R. E. Johnson, B. R. Palmer, D. K. Dysinger, R. B. Bhappu, A. E. Clark

The U.S. Bureau of Mines utilized a central composite experimental design to investigate leaching kinetics of pure chalcopyrite in the sulfuric acid-oxygen system. The six factors studied were oxygen pressures of 150, 300 and 450 PSI, leach temperatures of 35O, 65O, and 95O C, oxygen-to-chalcopyrite mass ratios of 0.5, 1.0 and 1.5, leach times of 8, 16 and 24 hours, initial acid strengths of 0.6, 1.2 and 1.8 g H,SO,/g chalcopyrite and pyrite to chalcopyrite mass ratios of 0, 1, and 2. Chemical analysis and oxygen consumption measurements indicatedthat leaching occurs through three consecutive reactions. Temperature was the primary determinant of leach rate and solution acidity was the primary determinant of oxygen consumption, sulfur oxidation, and activation energy.

Jan 1, 1993

By Scott G. Britton

This chapter discusses the necessary construction techniques for installing coal mine ventilation devices. Included in the discussion are the major air controlling devices called over- casts, regulators, stoppings, and doors. Under-casts, although a valid device, are used infrequently in coal mining and are not discussed here. Typically, coal mines require a great many ventilation devices to control the air movement. Post-I969 mines have had to design their air systems to comply with the Federal Coal Mine Health and Safety Act (CMHSA) as discussed in Chap. 1. Pre- 1969 mines have had to redesign major portions of their systems to comply with the basic components of the law such as separation of air courses, single unit split ventilation, and minimum air quantities. It is not uncommon, therefore, to find a large mine (2.0 Mt/a) requiring several hundred overcast installations (permanent, as well as repeat construction), plus doors and regulators placed among a thousand or more stoppings. When each of these devices is subject to leakage from installation and weathering defects, the importance of effective construction becomes evident. An historic rule of thumb for average mine ventilation says that about 70% of all the air pressure generated by the mine fan is lost between the portal and the working faces. Of course, this rule is subject to many factors, but the message is clear: there is a tremendous inefficiency in controlling leakage through common air devices. This chapter strives to present a standard approach and design alternatives which can go a long way in reducing this leakage, and hence, ventilation costs. Historically, mine ventilation has progressed from natural, or draft ventilation, to fire-induced ventilation (Fig. l), furnace-fired centrifugal fans and finally, to today&apos;s modem mine fans. Underground controlling devices have been in use in the coal mines since the late 1600s, but the CMHSA of 1969 was the real turning point for mine ventilation. Minimum quantities and velocities of fresh air were required for mining, forcing coal operators and engineers to reevaluate and improve their systems. As a consequence, the cost for ventilating air increased. Today, companies face a variety of choices among design alternatives, materials, labor, and costs of ventilating devices for their mines. The best approach for any individual company or mine is determined by (1) the needs of the mine, and (2) the local design parameters. In my discussions of ventilation construction I shall be fairly general in terms of device installation steps, where specifics are warranted for clarification, I will include this information.

Jan 1, 1983

By D. Raicevic

The presence of residual uranium and other radionuclides in the uranium mill tailings are posing a continuous health concern to the surrounding environment. The slow generation of sulphuric acid from residual sulphide minerals is the cause of persistant dissolution and discharge of many metallic components of the tailings. The most effective long term solution to these problems would seem to be to produce chemically stable tailings. This paper describes two possible answers to the objective: (1) Removal of radionuclides and pyrite from tailings by mineral dressing techniques; some 60 - 68% of the residual uranium, 70 - 75% of the radium, 60 - 65% of the thorium and 95 - 98% of the pyrite have been rejected from the Elliot Lake tailings. The decontaminated tailings contained 0.003% uranium, 50 - 60 pCi/g radium226, 0.01% thorium and less than 0.1% sulphur as pyrite. (2) Preconcentration of radionuclides and pyrite by beneficiation from Elliot Lake ores prior to leaching; applying this approach about 97% of the uranium, 95% of the radium, 92% of the thorium and 98.5% of the sulphides were concentrated in a radionuclide and pyrite concentrates comprising 25% and 8% of the ore, respectively. The preconcentration tailings (waste) produced contained 0.004% uranium, 20 - 25 pCi/g radium226, 0.005% thorium and less than 0.1% sulphur as pyrite. Economic and environmental advantages of both approaches and the leaching of the concentrates are also discussed.

Jan 1, 1980

By Huayang Luo, Hui Li, Wei Zhou, Gang Chen, Scott Huang

The beach and offshore gold resources demonstrated at Nome, Alaska are some of the richest found in Alaska. They contain potentially significant resources that may be exploited in the future. Several companies have contributed to the exploration and reserve estimation in Nome offshore gold deposits. More than 3,000 holes were drilled and over 10,000 offshore samples were analyzed in the Nome offshore areas of approximately 40 km2. Those 3,000 plus drill hole logs were converted into digital formats comparable with ArcGIS software. Considerable amounts of mineral resources data were processed and visualized using ArcGIS 8.3 and its geostatistic, 3D analysis, and spatial analysis components. In this study, based on the data processing and visualization results of ArcGIS, a user-friendly website for mineral resource management and utilization is developed using ArcIMS 4.0.1. ArcIMS is a GIS solution to build and deliver maps, data, and tools over the Internet. The Nome offshore mineral resources website presents the geostatistic and GIS analysis information. This site allows clients to access the information and perform ArcGIS analysis, such as interactive data query, and map layers display of the gold resource distribution, average grade, gold reserve, and relative mineral resource estimation via remote computers. With linkage to other related mining web sites, this web site allows users to search for related publications and more flexibly manage the information. A few other appropriate customized tools are also being developed to assist interactions between the server and clients for data analysis and management.

Jan 1, 2005

By Antonieta Middea, Rupen Adamian, Fernando F. Lins

This work presents the results obtained with aggregation of fine talc (-19 m), a naturally hydrophobic mineral, in the presence of KC1 solutions. The classical DLVO theory describes well the aggregation of talc in dilute KC1 solutions. Beyond 1 M KCI we have found indications that a non-DLVO interparticles force is operative, say an hydration (repulsive) force. This structural force could be responsible for the unexpected re-dispersion of talc suspension. However, no repulsive force (depression) has been observed in salt flotation of talc at higher ionic strength, up to 3 MKCI.

Jan 1, 1995

By R. E. Brewer

Pilot scale flotation tests were conducted with a 1-ft-diam column at the Barrick Resources (USA) Mercur mine, Tooele County, UT, to scavenge unleached (0.01 to 0.018 oz/st) gold values from the tailings of a carbon-in-leach (CIL) circuit. The optimal recovery was 35 pct of the unamenable-to-leaching gold, at a grade of 0.353 ounces of gold per short ton, using a mixture of dithiophosphate, xanthate, and diesel fuel as a collector. This was achieved by floating approximately 1.6 wt pct of the CIL tailings. The gold values are believed to be contained in arsenic-bearing minerals, attrited carbon, and carbonaceous material in the ore. Redox potentials were measured with a gold electrode during the conditioning stage prior to flotation. The correlation between flotation recovery and redox potential values could be used to control reagent additions. Treatment of a previously leached and weathered tailings material, averaging about 0.055 ounces of gold per short ton, was also investigated using the column. The tailings were first water leached at approximately 600 C, and the water-leached tailings, which contained approximately 0.03 ounces of gold per short ton, were then fed to the column flotation unit. The effects of pH and sodium sulfide addition on gold flotation recovery and redox potentials were examined. maximum gold recovery, 36 pct, was achieved at pH 8.5 with a sodium sulfide addition of 0.18 lb/st.

Jan 1, 1989

By W. F. McDermott

One of the major improvements in ore grinding economics in North America has been the introduction of autogenous grinding. The history of this has been well documented in previous AIME presentations and in the literature. Pickands Mather & Co. has been very active in the development of autogenous grinding since 1957. This early work led to the application of autogenous grinding to the Wabush Mines ore in 1965, with the installation of 6-24 ft. diameter by 8 ft. long - 1,750 HP mills. Development work recently completed in 1971 on another ore has led to the decision to install 5-36 ft. diameter by 15 ft. long - 12,000 HP mills when this project goes ahead. Between these two decisions lies a tremendous amount of research, development, and application of autogenous grinding to a variety of ores. The Pickands Mather Metallurgical and Research Laboratory in Hibbing, Minnesota has tested, in its pilot plant facility, ores from 9 different deposits. Some of these deposits have as much difference within their own ore types as there is between the various deposits. Therefore, it is safe to say that over 20 different ore types have been tested and flowsheets developed for commercial applications. Of the 9 projects, 3 are in operation. These are Wabush Mines in Labrador, Canada, (1) Savage River Mines in Tasmania, (2) and The Griffith Mine in Red Lake, Ontario, Canada. (3) Pilot plant work has encompassed over 300 individual tests. These tests were carried out in mills that were 5-1/2, 8, and 12 ft. in diameter. Grinding power requirements for the primary autogenous milling has varied from 2 to 30 KWH/Lt of crude ore.

Jan 1, 1972

By S. Rideout

The United States Department of the Interior&apos;s Office of Surface Mining (OSM) is responsible for regulating active coal mining and reclaiming abandoned coal mines in the United States. In working with the State government agencies that implement these programs, OSM is building a new approach that moves away from traditional "command and control" regulation and towards an approach that focuses on providing long-term environmental and economic sustainability on lands disturbed by coal mining. This initiative called "Reclaim the Future!" looks to enhance opportunities for economic development, wildlife preservation and enhancement, reforestation, and other beneficial and productive uses of lands disturbed by coal mining. The initiative is also focused on ensuring that the landowners and the local public have significant involvement in determining how best to reclaim mine sites and what post-mining land uses are most appropriate for each individual abandoned mine reclamation project or active mine reclamation. Through the use of the best scientific input in an open, participatory process, OSM hopes to further sustainable development principles for coal mining within the framework of existing United States law.

Jan 1, 2007

By M. Poulton, J. A. Botín, C. Gatica

"The Chilean minerals industry faces a shortage of 27.000 new skilled professional by 2023. Enhancing the integration of women into the workforce is a possible solution. This study analyzes the state of women in the mining workforce over the past decade. Several key indicators are presented: percent in the workforce, salaries, career profiles, presence at management level, and participation in academia are studied. The study also analyzes the strategies used by government, industry, and universities to recruit and retain women for the minerals industry. The main results show that women represent 7.4% of the mining workforce in Chile and less than 1% of senior positions with a salary gap of approximately 30%. Systematically, women prefer professional programs in geology, chemistry, and environmental areas. The Chilean statistics are compared to data from the United States mining industry. INTRODUCTION The Chilean mining industry faces a significant shortage of professionals for the next decade which compromises competitiveness and productivity. The demand for human capital in mining depends on several factors. First, the age structure of workforce, which determines future retirement needs. Second, minerals market considerations, determining the amount and size of mining projects entering production in the coming years. Third, the evolution, positive or negative, of productivity, mainly driven by technology and innovation, and negatively affected by the declining ore grades. Finally, negative trends in lead times to production of mining projects, due to social opposition, changing regulations and other project contingencies, negatively affecting the demand for human capital. Regarding the supply of human capital, the fast increase in the technology level of the minerals industry and hence, the increase of technical qualification requirements of the human capital generates a rise in the time required for trade and university education of mining professionals, which may cause imbalances in the labor market. According to (Consejo Minero, 2014) human capital gap in Chile by 2023 will be around 27.000 workers for extractive, processing and maintenance jobs, which represents 14% of the current workforce (Figure 1)."

Jan 1, 2016