Search Documents

By Ernst Langer

INTRODUCTION Morro do Niquel is located near the small town of Pratdáolis in the southwest part of the State of Minas Gerais, Brazil, about 300 km in a straight line north of São Paulo and 300 krn west of Belo Horizonte. The deposit is known since 1935. Systematic exploration started, however, only in 1957 and production with one furnace in 1962. Since 1969, after the installation of a second furnace, the mine produces about 2 500 tons of nickel, contained in ferronickel, per year. This production is now consumed totally by the Brazilian steel industry. The "Morro do Niquel" is a serpentinite stock of 900 by 400 m which rises 200 m high above the surrounding metamorphic rocks of Algokian age (see Figure 1). On top of the hill there is a leached barren zone of about 200 by 400 m, generally 20-30 m deep, which consists practically only of a boxwork of quartz colored brown by limonite. Surrounding this zone on the sides of the hill is weathered, decomposed serpentinite which contains about 213 of the economic nickel mineralization. Roughly 113 of the ore reserves lie below the leached overburden representing ore of a different type. The geological map and cross-section, Figure 2, give a clear picture of the occurrence.

Jan 1, 1979

By J. Pang, S. Chander

The results of an investigation to characterize the chalcopyrite/solution interface are presented. Several techniques were used, including galvanostatic and steady-state polarization, cyclic voltammetry and impedance spectroscopy. The results show that the dissolution of chalcopyrite was incongruent. Initially, at low potentials (< 0.12 V), iron species were released that led to the growth of an iron-deficient sulfide (IDS) layer (referred to as the "reacted layer" in this paper). Depending on the solution&apos;s composition, the dissolved iron might reprecipitate as a hydroxide layer. In the potential range of 0.12 V < E < 0.23 V, the IDS layer was passivating. In comparison, development of a passivating IDS layer under galvanostatic conditions led to a jump in potential to 0.48 V. The IDS layer began to dissolve at potentials greater than 0.24 V. The dissolved species precipitated to form a product layer in alkaline solutions. Continued oxidation involved diffusion of species through the reacted and product layers. At higher potentials (> 0.48 V), further oxidation led to the dissolution of the copper and sulfur species, with a resultant breakdown of the IDS layer. The changes in surface-coating properties, resulting from various electrochemical treatments, are discussed.

Jan 1, 1993

By J. Noll, C. DeGennaro, C. Zhou, J. Srednicki

"The personal dust monitor (PDM) (model PDM3700), as well as other electronic devices, can cause electromagnetic interference (EMI) which can disrupt the operation of some proximity detection systems (PDSs). A 15 cm (6 inch) minimum separation distance between the miner-wearable component (MWC) of the PDS and the electronic device usually avoids these disruptions, but due to the amount of equipment on a miner’s belt and the method of wearing the PDM in some situations, this distance can be difficult to always reliably maintain. Another method of reducing EMI effects is utilizing magnetic field shielding. The shielding capability of several different materials was investigated by surrounding the PDM with the material and quantifying the EMI. A copper mesh pouch reduced the EMI from a PDM3700, allowing a minimum separation distance of 10 cm (4 inches) instead of 15 cm (6 inches) as shown in a previous study for an unshielded PDM. A MU-metal box had a better shielding effectiveness, as it further reduced the minimum separation distance to less than 7 cm (2.8 inches). Shielding reduced the EMI of the PDM with MU-metal providing better results than the copper mesh. These materials may be beneficial for shielding individual components of the PDM or for constructing a shielded pouch. However, before the advantages of a shielded pouch can be determined, the effects of just the shielding material (metal) on the PDS needs to be quantified. INTRODUCTION According to statistics from the Mine Safety and Health Administration (MSHA), 43 miners have been fatally struck or pinned by a continuous mining machine (CMM) since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems (PDSs) have been developed and are required on all operating CMMs in underground coal mines, with the exception of full-face CMMs, by 2018 (MSHA, 2015)."

Jan 1, 2018

By Bok-youn Kim

Presently, mobile diesel equipments contributes a lot in improving the economical feasibility of underground mining and tunneling operations. Even in Korea, quite a large number of diesel equipments is being applied to the underground workings already. This paper introduced the production procedure, characteristics and evaluation technology on diesel particulate matter(DPM) that is known as a carcinogen For easy measurement of DPM using laser dust monitor, the conversion factor(K) to gravimetric concentration was acquired. The field measurement of DPM was conducted to make a comparison between locally manufactured on-road equipments and imported equipments specially designed for underground use. According to the Government regulation revised h 1996, it was learned that the critical pollutants among the diesel exhaust is DPM instead of NOx which have been considered as a critical pollutants.

Jan 1, 1997

By A. Bruynesteyn

Many papers &apos;have been publihed on the role of the bacterium.Thiobacillus ferrooxidans in the oxidation of reduced sulfur compounds, and years of research have established the following environmental factors, which influence biological oxidation. 1. Oxygen is required for the oxidation of reduced sulfur compounds to the sulfate form. Sufficient oxygen. is available from the air, consequently, it is of importance to get the air to the bacteria. 2. The bacteria are active in the pH range 1.4 3.5. Maximum activity occurs at pH 2..0 - 2.8. 3. -In order to allow the bacterial populations to expand, certain essential nutrients must be available. Nitrogen has to be supplied for the production of body protein, and ammonia is the source most readily accepted by the bacteria. Carbon dioxide is the only utilizable source of carbon and the small amounts available in air are the primary source of this element. Small amounts of phosphate, manganese,, potassium,. calcium. and magnesium are also required. These trace minerals are available from the water and host rock in sufficient quantities. 4. Water is required as a carrier for the oxygen carbon dioxide and other nutrients, as-well as a solvent for the metallic sulfates produced. The bacteria are motile and the water allows the bacterial populations to spread:: bacterial activity ceases if the equilibrium relative humidity drops below 100%. 5.-optimum bacterial activity occurs at temperatures of 34 - 35°.C (93 -.95° F). All activity ceases above 45° C. At lower temperatures, activity its dramatically decreased, but there is still a significant amount at 10 - 11° C.- Thiobacillus ferruoxidans has been isolated from a mine with a year round temperature of 3° C. 6. Unpublished results from our laboratory show that biological leach ore oxidation takes place during the rest periods at the same rate as during the wet leaching periods providing there is a film of moisture remaining around the particles. Optimum conditions can be readily achieved in the laboratory, but application of our laboratory knowledge to commercial leaching dumps is riot as simple. Attempts to achieve improved environmental conditions for the bacteria in leaching dumps would require substantial capital investment and careful planning of leaching operations. This paper

Jan 1, 1972

By S. Hicks

This technical note describes an alternative procedure that can be used in linear programming calculations where the compliance limit of lbs SO2/million Btu for the blending coal is subject to change. Dr. Mateer in his technical note titled "Coal blending for sulfur compliance" (ME, September 1994, p. 1103) defined an "excess sulfur" parameter that provides a valid constraint equation for a linear program optimization. The coals used by Dr. Mateer in his examples are shown in Table 1. To create the parameters for the constraint equations to blend to an SO2 content of 1.2 lbs SO2/million Btu, the excess sulfur for Coal A was defined as Sulfur excess% = 0.5 - 0.6*13,000/10,000 = -0.28 This equation was used to create the constraint equation -0.28A + 0.44B + 1.36C[<] 0.0 Another way to create the parameters for the constraint equation is given below. In these equations: •W is the total weight; •A, B and C are the fractional proportions of each potential blend stocks; •Sa, Sb and Sc represent the percent sulfur content of the blend stocks; •Ha, Hb and Hc represent the calorific content of the blend stocks in Btu/lb; and •H and S represent calorific and sulfur contents of the composite blend. The weight of blend to produce one million Btu is [ ]

Jan 1, 1998

By John P. Dunford, Lewis A. Martin

Researchers from the Spokane Research Laboratory, National Institute for Occupational Safety and Health, in cooperation with engineers from the Department of Mining and Geological Engineering, Montana Tech, Butte, MT, conducted tests to evaluate the tensile strength, fiber count, and adhesion of shotcrete applied to panels at the Chief Joseph Mine, a research and training facility operated by Montana Tech. The tests were conducted in the mine ramp 45 m (150 ft) inward from the access portal at a 15.25-m- (50-ft) long test area divided into five 3-m- (10-ft) long sections. The shotcrete was applied with an Aliva 240.5 machine fitted with a predampener. Different amounts of fiber were entrained for each panel. Background data for the tests were obtained from earlier tests in Nevada, where the typical amount of fiber in the shotcrete is 6.54 kg/m3 (11 lb/yd3). All shotcrete was applied to a minimum thickness of 76 mm (3 in). Cylindrical cores were drilled at the wall-rock interface, and adhesion was tested after 28 days of curing. The goal of this research is to reduce the need to install multiple supports at the advancing face by creating a safer mining system that limits the time miners are exposed to unprotected roof.

Jan 1, 2005

Bioleaching of solid wastes lithium ion battery industries was carried out in this investigation. A new method for recovery of cobalt, potentially the basis of an economic and environmentally friendly process was examined. The present study was conducted using chemolithotrophic and acidophilic bacteria Acidithiobacillus ferrooxidans and some mixed thiobacilli collected from abandoned mine drainage. These organisms were able to utilize sulfur and ferrous ion as energy source. Bio-dissolution of cobalt was found to be faster than lithium. The effect of initial Fe(II) concentration, initial pH and solid/liquid (w/v) ratio were studied in detail. With increase of time of leaching the dissolution of cobalt was found to be increased and this must be due to competitiveness of the mixed thiobacilli for utilizing the energy source among them. Since the bacteria are belonging to acidophilic group the higher pH studies revealed a decrease trend in metal dissolution. Higher solid/liquid ratio also found to be detrimental for the bacterial activity. It seems bacteria are not resistant to higher concentration of the metal. The optimized conditions for bio-dissolution were sol-id/liquid (w/v) ratio - 10 g/L, initial Fe(II) concentration - 5 g/L, elemental sulfur - 1% (w/v). In the optimized conditions, cobalt dissolution was observed to be about 75 % whereas that of lithium was 15% after 25 days.

Jan 1, 2006

By A. J. Stewart, R. L. Shufflebotham, D. W. Ferguson, T. L. Page

The Inter-Island Tunnel is a 7.7 kilometer (25,160 foot) long by 3.5 meter (11.5 feet) diameter concrete lined tunnel through the Cambridge formation below Boston Harbor. Constructed as part of the Boston Harbor Project, this tunnel will bring untreated wastewater from the MWRA’s South System headworks facility at Nut Island in Quincy, MA to the new Deer Island treatment plant. A myriad of problems delayed the construction of the tunnel. These problems included salt water inflows of over 22,000 liters (5,812 gallons) per minute, a major fire in the access shaft, weak rock and soil collapsing on the tunnel boring machine, and hand mining operations.

Jan 1, 1997

By S. K. Kawatra, S. J. Ripke

During iron ore pellet production, bentonite clay is used as a binder. Typical pellet plants spend from $3 million to $5 million annually for the clay. If bentonite dosages could be reduced by using it more efficiently, a significant cost savings would result. If the binding mechanisms can be completely understood, procedures can be developed to use bentonite more efficiently. Classical bentonite bonding theory is based on the behavior of bentonite at low percent solids and high mixing shear rates. Under these conditions, bentonite was understood to expand, disperse into platelets, and dry into a bonding "film" or "gel." However, these are not the conditions that exist during pelletization, which is carried out at high percent solids and relatively low shear rates. In this paper SEM imaging was used to identify and explain the bonding mechanisms of bentonite on the surface of magnetite concentrate. It was determined that bentonite would form a fibrous network under the proper conditions and that the formation of these fibers corresponded with an increase in the bonding of particles by the bentonite.

Jan 1, 2000

By Donald Whittaker

Severe climatic conditions in mines are normally associated with working at depth. More precisely, it is a matter of working in regions of high strata temperature, since, for example, some coal mines in the Ruhr have strata temperatures at 1000 m which are matched only at 3 times that depth in the South African gold mines. In Britain we are perhaps fortunate in encountering strata temperatures in our deeper coal mines some 10-15 K lower than at the same depth in the hot mines of the Ruhr. Nevertheless the problems of high temperatures and humidities in UK mining operations, which in the past have been confined to a few specific sites, have in recent years become more widespread, and there is every reason to suppose that the trend will continue. Clearly strata temperature is not the only .causative factor. Long ventilation circuits serving districts remote from the shaft must also play a part, while the heavy use of machinery and the rapid, rates of excavation of modern mining methods are obviously important. It is necessary to understand the mechanisms of all such factors, and to measure their magnitudes and fluctuations, if remedial measures are to be properly designed or predictions made which are accurate enough to be of use in ventilation planning. This paper presents the results of a long-term (and continuing) investigation carried out in several mines to measure the major sources of heat and moisture on longwall districts and trunk conveyor roadways. The variation with time of these sources is reported, and the resultant effect on the climate is considered. In their investigations of the heat exchanges occurring in a whole mine Oakes and Hinsley (1955-56)1 listed and estimated the magnitudes of a large number of heat sources. Some of these, namely autocompression of the air in the shaft, diesel engines and compressed air mains, do not apply to the present investigations, which refer to longwall districts with conveyor transport and no compressed air supply. Others, such as oxidation of coal and, desorption of methane, have not been taken into account in the measurements, but are discussed later. One other source, the importance of which was pointed out by Gracie and Matthews (1975)2, is the coal on the conveyor, a form of strata heat emission, but one which is strongly dependent on the rate of coal production. The heat emissions measured in the present investigations were the energy consumed by electrical machinery, the heat conducted from the strata and the heat lost by the conveyed coal. Most of the emitted heat was removed from the district by the ventilation air, and was measured by continuously recording the enthalpy of the air at fixed stations. The heat removed by service water, supplied for machine cooling and dust suppression, was also measured. Account was of course taken of the relatively minor changes in level around the districts, in terms of the potential energy gained or lost by the coal and by the ventilation air (autocompression).

Jan 1, 1980

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

"The National Institute for Occupational Safety and Health (NIOSH) recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with mediumsized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in the present study: a 15.2-cm (6-in.)-wide shelf; a 7.6-cm (3-in.)-wide shelf; and a 7.6-cm (3-in.)-wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1 and 1:1 were evaluated for the 15.2-cm (6-in.)-wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. IntroductionSurface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1 percent of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples).• 5.8 percent of rotary drillers were overexposed to respirable silica dust (nine out of 155 samples).• 7.3 percent of drill helpers were overexposed to respirable silica dust (three out of 41 samples).• 7.5 percent of blasters/shotfirers were overexposed to respirable silica dust (three out of 40 samples)."

Jan 5, 2018

By Ralph van Rijswick, Erik Vlot

"Anglo American operates 18 Weir GEHO piston diaphragm pumps (PD) in the two pump stations of the 52-km (32-mile) long Minas Rio iron ore concentrate pipeline. The pipeline is designed to transport 26.5 Mt/a (29.2 million stpy) of concentrate from the mine to the export terminal at the coast.During the commissioning of the pipeline in the fall of 2014, high pressure pulsation levels were experienced, with peak-to-peak levels as high as 20 bar. Based on pressure readings it was concluded that hydraulic resonances were present in the system, which were excited by the third and sixth harmonic of the flow pulsation generated by the pumps.Based on this observation, Weir Minerals Netherlands, manufacturer of GEHO PD slurry pumps, recommended installing a phase shift controller that controls the phase shift between the crankshafts of the individual pumps, thereby minimizing the effect of the hydraulic resonances.GEHO piston diaphragm pumps and pressure pulsation analysisPiston diaphragm pumps are used worldwide to transport abrasive and/or aggressive slurries against high discharge pressures in the mining, mineral processing and power industries. The basic operating principle of a piston diaphragm pump is shown in Fig. 1.A crankshaft is driven by an external electric motor via a gearbox. The crank mechanism transfers the rotating motion of the crankshaft into a reciprocating motion of the piston. The piston displaces a hydraulic fluid, called the propeling liquid, which displaces an elastic rubber diaphragm. When the piston moves to the right, the pressure in the pump chamber drops below the suction pressure and the nonreturn valve on the suction side will open, allowing the pumped fluid to flow into the pump chamber. When the piston moves to the left, the fluid is compressed, and when the pump chamber pressure rises above the pipeline pressure, the nonreturn valve on the discharge side will open allowing a displacement of fluid into the discharge line. The main objective of the diaphragm is to isolate the piston and the drive mechanism from the abrasive and/or aggressive fluid and create a hermetic seal between the pumped fluid and the ambient environment. Piston diaphragm pumps as shown in Fig. 1 are among the largest positive displacement pumps in the world and have been produced with stroke volumes of up to 100 L (26 gal) per pump chamber for flow rates up to 800 m3/h, discharge pressures up to 250 bar and hydraulic outputs over 2 MW per unit (van Rijswick et al., 2010)."

Jan 9, 2017

By Paul L. Russell, R. G. K. Morrison

9.1-CLASSIFICATION OF MINERAL DEPOSITS AND ROCK MATERIALS After a mineral deposit has been discovered, delineated and evaluated, the next step is to select a mining method that is physically, economically and environ- mentally adaptable to recovering the mineral from the deposit. The term "mineral deposit" is used to denote a concentration of mineral (including rock and coal). Even where there is considerable past experience available, many of the critical design criteria must be determined utilizing only information obtained from an examination of exploratory drill core specimens. The factors that affect this selection are as follows: (1) the spatial characteristics of the deposit (size, shape, attitude and depth); (2) the physical (or mechanical) properties of the mineral deposit and surrounding rock; (3) ground water and hydraulic conditions; (4) economic factors, including grade of the ore. comparative mining costs and desired production rates; and (5) environmental factors, such as the preservation of the surface overlying the mine, and the prevention of air and water pollutants. Of these factors, the spatial characteristics of the deposit and the physical (or mechanical) properties of the mineral and surrounding rock limit the methods that can be employed to mine it. Six types of mineral deposits are recognized, as follows: 1. Massive-A deposit of considerable lateral and vertical extent in which mineralization (or ore) is relatively uniformly distributed. Disseminated copper ores are typical deposits. Dome salt also is included in this classification. 2. Bedded or Tabular-A mineral deposit that parallels the stratification, most often in sedimentary rock, usually laterally extensive, and of limited thickness. Most coal measures and some evaporite mineral deposits (e.g., potash) fall in this class. 3. Narrow Vein-A zone or belt of mineralization (ore) typically long, narrow (less than 10 ft), often dipping steeply, and usually lying within boundaries separating it from neigh- boring rock. Many gold and other metallic minerals occur in narrow veins. 4. Wide Vein-As defined under narrow vein except that the vein thickness is greater than 10 ft. 5. Lentictclar or Pocket-An isolated ore body, or an enrichment of limited vertical and horizontal extent in a massive, bedded or vein deposit. Lead, zinc and iron ores often occur in this type of deposit. 6. Placer-A surface or near-surface deposit, usually tabular and may be of consider- able areal extent, containing mineral particles (e.g., gold, platinum) in detritus (e.g., sand, gravel). The rock materials associated with mineral deposits are classified as follows: 1. Detritus-Sediments and other accumulations of solid particles produced by the mechanical and/or chemical disintegration of rocks, and usually having a low cohesive strength and very low compressive strength (e.g.. soil, sand, gravel, alluvium, playa). 2. Jointed and Fractured-Unbonded-A rock mass, often occurring on or near the surface or in fault zones, in which the joints or fractures contain alteration or decomposition

Jan 1, 1973

By Tom B. Corry

INTRODUCTION Located approximately 48 km (30 miles) south of Dallas, Texas, use to be the site of the Superconducting Super Collider. For those of you unfamiliar with the project, this was a multi-billion dollar project taken on by the U.S. Government for the further advancement of technology, medicine, and science. Major components of the project consisted of a Linear Accelerator known as the LINAC; three accelerating rings known as the Low Energy Boosters (LEB), Medium Energy Booster (MEB) and the High Energy Booster (HEB); the East and West Campuses where the Inner Reactor Halls would have been located; and the 87 km (54 mile) main collider tunnel. Unfortunately, this all came to an end on December 6, 1993, with the termination of the project due to the Government&apos;s cancellation of funds. This paper will deal with the two of the underground contracts before the termination. These two contracts were the 1122 contract which ran from N25 to N40 and the 1130 contract which ran from N40 to N55. (See figure 1) The 1122 contract was awarded to us in July of 1992 and consisted of the excavation and support of six (6) shaft varying in diameter from 5.5 m (18 feet) to 8 m (26 feet) and ranging from 39.6 m (130 feet) to 61 m (200 feet) deep and the driving of approximately 13,100 m (.43,000 If.) of main collider tunnel. Our second contract, the 1130, was almost identical to our first

Jan 1, 1995

By W. J. Wuest, M. J. DeMarco, J. R. Koehler

Yield-pillar-based gate-road designs often fail to provide mine operators with adequate ground control. This is because of the unknowing m is employment of "critically" sized pillars. A "critical” pillar is one that is too large to either yield nonviolently or to yield before the roof and floor sustain permanent damage and is too small to support full abutment loads. To demonstrate the critical pillar concept, afield study of a tapering gate road was conducted by the US Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m (55.1-ft) wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m (40-ft) wide design more closely approaches proper yield pillar dimensions. A probe hole in several 10.6-m (34.8-ft) wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1997

By D. H. Y. Tang, S. S. Peng

Three-dimensional finite element modeling (3-D FEM) was performed to analyze the safety factors of stump pillars, 5.5 m x 5.5 m, under a cover of 63 m using the Modified Drucker-Prager Theory. The results showed that they were safe. This was substantiated by underground observations. But the safety factors predicted by three commonly used pillar design formulae showed otherwise. This paper discusses the modeling details and analyzes the difference between 3-D FEM method and traditional pillar design formulae.

Jan 1, 1987

By S. Behl

In the selective flocculation process, polymers with specific functional groups can yield highly selective adsorption and, therefore, high separation efficiency. Selectivity in polymer adsorption may also be attained by specific additives that inhibit the adsorption of the flocculant on some solid surfaces but not on others. Generally, these additives have a different chemical nature than the flocculant. In this study, the lower molecular weight fraction of the flocculant was successfully evaluated as a site blocking agent, leading to higher separation efficiency than obtained otherwise.

Jan 1, 1993

By S. Su, S. Natansohn

This report describes a process for tungsten recovery from Searles Lake brines and upgrading its concentration to useful levels. The method consists of a combination of a liquid-solid and liquid-liquid extraction step and results in a product stream containing more than l00g W03/1. This technique is also effective in substantially reducing the concentration of objectionable impurities in the tungsten product. An ion exchange extraction mechanism is postulated.

Jan 1, 1983

By S. O. Yuan, R. L. Grayson

As a followup to a USBM-sponsored research project, the authors utilized the knowledge-base structure and system concepts from a Sun Sparcstation-based worker-scheduling system of the mine-management support system to develop a PC-based application. The new software adopts the nested-window concept to facilitate data collection and modification on personnel, including their availability and work priorities during a shift. The system can optimally allocate manpower on a work shift and can delineate supervisory training responsibilities. The various components of the software, including enhancements made to the original system, are described in detail.

Jan 1, 1998