Search Documents

By K. S. Eric Forssberg, Lennart Ryk

The paper discusses coal utilisation in Sweden. All hard coals have to be imported from other countries. Peat from domestic sources is used as a complement. Environmental legislation and taxation on fuel and emissions are severe. This situation affects the procurement, preparation, handling and use of coal. The paper presents: • R&D projects concerning deep cleaning of thermal coal. • Handling and treatment of coal used in PFBC boilers and for blast furnace injection • Dust prevention for coal and peat briquettes. Procurement of coal emphasising quality and environmental issues.

Jan 1, 1995

By Pradip

It is possible to beneficiate low-grade phosphate ore slimes containing predominantly siliceous gangue by a combined selective flocculation-flotation scheme using commercially available reagents. The presence of clays, in particular, montmorillonite and attapulgite, has a disastrous effect on the efficiency of separation. Suitable remedies to overcome this problem are not yet available. Intensive R&D efforts are required in the areas of the design and synthesis of specific reagents, the effect of particle size, and the design of appropriate process equipment to carry out flocculation and flotation of slimes.

Jan 1, 1989

By Donald S. Clarke

The Umuna epithermal precious metal deposit has provided the target for a simulated rock geochemistry exploration program, directed at bedrock exposed in the drainage system of eastern Misima Island. A geochemical halo to the deposit is readily recognised in the mafic meta-volcanic country rock. This halo is defined by anomalous results for both major (K, Na, Ca, Mg) and minor (Au, As, Sb, Cu, Pb, Zn, Ba, Rb, Sr, Cs, Bi, Ga, S) element geochemistry, extending further than 1km from the deposit. Such halos are sufficiently extensive to provide adequate exploration targets in the search for epithermal mineralisation, complementing mineralogic and secondary media geochemical investigations.

Jan 1, 1989

Energy Developments Ltd. (EDL) has developed power plants at two Australian coal mines that featuring 94 gas-fueled Caterpillar G3516 engine/generator sets. They will convert to electricity 145 kt/a (160,000 stpy) of coal-seam methane gas for sale to a local utility. The $100-million project will cut the sites' methane emissions in half, provide a low-cost energy source and offset mine operating costs. The project began in May 1995. It is located at the Appin and Tower longwall underground mines, 80 km (50 miles) south of Sydney in New South Wales. The installation is one of the first to capture coal-seam gas from mine ventilation air and gas drainage systems. Coal- seam gas contains 40% to 60% methane, which fluctuates constantly. The system is expected to convert 578,000 m3/d (20.4 million cu ft/d) of coal-seam gas to 94 MW. It will also reduce greenhouse gas emissions by 3.5 Mt/a (3.8 million stpy) of CO, equivalent emissions. The Appin and Tower mines each produce 2 Mtla (2.2 million stpy) of clean coking coal. They operate around the clock with about 400 workers per site. The mines are owned by BHP Steel, Collieries Division, which will share the revenues from energy sales. The Appin Power Partnership consists of EDL and Lend Lease Development Corp.

Jan 1, 1997

By W. R. SHAHAN, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation on the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). 

By Rudolf Kvapil

INTRODUCTION Sublevel mining is a mass mining method based upon the utilization of gravity flow of the blasted ore and the caved overlying waste rock mass. As with any other mining method, sublevel caving has advantages and dis¬advantages which must be carefully considered and evaluated. The major advantages of sublevel caving are dis¬cussed as follows: Because all of the mining activities are executed in or from relatively small openings, sublevel caving is one of the safest mining methods. Drifts, which are the pri¬mary working places, are distributed in a uniform pat¬tern on all levels. Normally the maximum dimensions of the sublevel drifts are about 5 m wide and 3.7 m high. The transportation drifts can have the same section, or the height may be increased to about 4.5 m when trucks are loaded in the transport drifts. The stability and safety of such drifts in competent rock can be easily controlled by smooth blasting or by a combination of smooth blasting with shotcreting. In less competent rock masses, stability can be achieved by combined reinforc¬ing, for example, by a combination of smooth blasting, shotcreting, and rockbolting. The major mining activities can be broken down into three groups: drifting and reinforcing; ore fragmenta¬tion, i.e., production drilling and blasting; and ore draw¬ing, loading, and transportation, and all are relatively simple. Because of the repetitive nature of the mining system, one can standardize almost completely all min¬ing activities. This means that a high degree of work efficiency can be achieved. Because the components of mining production in sublevel caving can be standardized, a high degree of mechanization is possible. In modern sublevel caving the sections of drifts and tunnels are sufficiently large to allow the introduction of large trackless mining equip¬ment. The advantages of a trackless system can be then broadly utilized not only for direct mining but also for all services, including the transportation of mining per¬sonnel to the working place. The flexibility of mining is very good. Standardiza¬tion and specialization of mining activities and equip¬ment on separate levels (lower level or levels in de¬velopment, upper level or levels in production mining) together with the trackless system yield a high degree of flexibility. This allows a rapid start-up of mining and good flexibility in making production rate changes. The method lends itself to good work concentration, organization, and working conditions. Normally, on the lower levels, various phases of development are under¬way. Upper levels are in various stages of extraction. Therefore the work can be easily organized into a sys¬tem which excludes interference between mining activi¬ties. Safety of mining (in small dimension openings), good work organization, high mechanization using large modern mining equipment, etc., comprise very good working conditions. Naturally such a system enables a high work concentration and rationalization of separate specialized mining activities and therefore mining by sublevel caving can be effective and relatively in¬expensive. The major disadvantages of sublevel caving, on the other hand, are: There is a relatively high dilution of the ore by caved waste. Various types of ore loss can occur. When the ex¬traction limit (that point yielding the maximum accept¬able amount of dilution) is reached, the remaining highly diluted ore represents an ore loss. Some ore is lost in passive zones located on the level of extraction between the active zones of the gravity flow. Part of the ore from these passive zones can be recovered together with ore extraction on the lower sublevel, but some un¬diluted and often not fragmented ore located in passive zones above the plane of the footwall is lost. In gen¬eral, these losses are larger as the inclination of the ore body and the footwall is reduced. A relatively large amount of development is re¬quired. This includes transport drifts, usually located in the footwall waste rock on each sublevel, and sub¬level drifts, which connect the active mining areas to the transport drifts and as a result are partially in ore and partially in the waste rock of the footwall. The waste rock length increases as the inclination of the ore body and footwall decreases. It also includes orepasses, used for transport of the ore or waste from the separate sublevels downward to the main haulage level, and normally driven in waste; and inclined drifts or tunnels, which provide a connection for the trackless equipment between the main haulage level and the separate sublevels and are driven in waste. Finally there is the de¬struction of the surface through subsidence. To maximize the ore recovery, minimize the dilu¬tion, and achieve a high efficiency of mining by sub¬level caving, good data regarding the gravity flow pa¬rameters for the blasted ore and the caved waste are of utmost importance. The exact type and amount of data required depend upon the purpose and needs of the study. For the first feasibility study, it may be sufficient to utilize the data from other sublevel caving operations with similar conditions and circumstances. For any higher level of mine planning it is clear that more exact data, including analytical and experimental analyses up to full-scale in-situ testing, are necessary. Basic gravity flow principles and design guidelines for the application of the sublevel caving mining method are presented in the following sections. Although some¬what simplified, they should provide a basis for mine planning and operation. The gravity flow principles described can be effectively applied to other mining situations, with some modification. Also, steep dipping coal seams can be effectively mined by modified sub¬level caving.

Jan 1, 1982

By Jerry C. Tien

China?s remarkable levels of economic growth during the past three decades have lifted almost 300 million people out of poverty. This amazing achievement has placed an increasing demand on energy and minerals, especially coal, which supplies 68.7 percent of China?s energy (June 2011). It is estimated that China mined more than 3 Gt (3.3 billion st) of coal in 2010, three times as much when compared to merely 10 years earlier. Such an impressive achievement does not come without major costs ?? including concerns with mine safety and an increasing number of occupational illnesses due to fast growth. This article reports on one of the major safety concerns in China?s coal mining, dust and dust control practices, and known cases of caol worker?s pneumoconiosis affiliated with prolonged exposure to excessive coal dusts. The exact size of China?s mining industry is not known, but it is estimated the coal industry is at least five-million people strong, and the metal and nonmetals industry probably employs another three million people. To meet increasing energy demand, China mined more than 3.1 Gt (3.4 billion st) of coal in 2010 from its 15,000 plus coal operations1, most of which are small- to medium-sized operations with annual coal productions ranging from a few thousand tons to 300 kt (330,000 st). These small coal operations are typically in remote areas, inadequately engineered, poorly ventilated and still using rudimentary drilling and blasting mining methods employing antiquated mining equipment and, presenting safety concerns, i.e., methane and dust explosions.

Jan 1, 2011

By S. Potgieter-Vermaak, T. T. Chiweshe, W. Purcell

The advantage of using ammonium phosphate salt as flux is the selective precipitation of chromium(III) compounds, which are considered nontoxic and environmentally friendly. The technique in this paper is determined to have potential to be applied in the metallurgical industry, where it can be used in the beneficiation of chromite mineral ores. The higher chromium contents of chromite ores often require furnaces to run at higher temperatures of above 1,300 °C, which can cause shutdown of the ore processing plant and accumulation of the sticky chrome compounds — including toxic chromium(VI) waste — which are generated as byproducts. The other advantage of this technique is its low to moderate energy consumption compared to existing techniques.

By M. Yekich, W. R. Reed, G. Ross, M. Shahan

"Canopy air curtains (CAC) on roof bolting machines have been proven, through laboratory and field investigations, to protect miners from respirable dust, preventing dust overexposures. Another desired application is to develop a CAC that is mounted in the compartment of a shuttle car to protect the operator from dust. The challenges faced with this design include mine ventilation rates in tandem with the shuttle car tram speeds, causing cab airspeeds that may exceed 600 fpm, as found in this study of a central Appalachian underground coal mine. Prior research and laboratory testing indicate that successfully protecting a miner in high air velocities is difficult to achieve because the clean air from the CAC is unable to penetrate through the high velocity mine air and make it to the breathing zone of the operator. During this investigation by researchers from the National Institute for Occupational Safety and Health (NIOSH), dust concentrations of the shuttle car operator were measured. Also, air velocities experienced by the operator were measured using a recording vane anemometer. Results from the survey indicate that the highest exposure to respirable dust (2.22 mg/m3) occurred when the shuttle car was loading at the continuous miner, where there was an average airspeed of 157 fpm. While tramming, the operator was exposed to 0.77 mg/m3 of respirable dust with an average airspeed of 203 fpm. This study indicates that a CAC system can be designed to greatly reduce an operator’s exposure to respirable dust by providing clean air to the operator, since the majority of the operator’s dust exposure occurs in air velocities less than 200 fpm. INTRODUCTION NIOSH has issued a contract (#200-2015-63485) with Marshall University and J.H. Fletcher & Co. (Salem et al., 2016) to develop a canopy air curtain (CAC) for coal mine shuttle cars. The proposed design maintains a similar design to the roof bolter CAC by providing filtered air via a blower over the operator. The plenum, which will provide the uniform airflow over the operator, is anticipated to be built into the shuttle car canopy. One of the main interferences with a CAC is ventilation airflow perpendicular to the plenum airflow [Engel et al. 1987]. This ventilation airflow, if the velocity is significantly high, can shear the downward flow from the plenum. The shear caused by the ventilating airflow can reduce the effectiveness of the CAC by either disrupting the downward flow or allowing contaminated mine air into the CAC zone of protection."

Jan 1, 2018

By Jon G. Baird

The suggestion of the use of measurements of trace amounts of mercury as a guide to the location of sulphide ore deposits was first made by the Russian, A. A. Saukov (1), in 1.946. Since Saukov's original work, many others have studied the abundance of mercury in nature, the association of mercury with sulphide ores and methods by which very minute quantities of mercury can be measured in air, soil, rocks, water and plants. The most abundant of the mercury bearing minerals is cinnabar (HgS). Native mercury is also found and sulpha-salts like tetrahedrite are known to have important mercury contents. Other sulphides of base metal deposits contain mercury in amounts ranging from parts per million to as much as one or two percent. (2) The mercury content of sulphide-free rocks is usually less than a few hundred parts per billion (1 ppb - 10-9), Soils usually contain less than 100 ppb and water less than 1 ppb of mercury. Normal atmospheric air contains about 1 nanogram (10-9 grams) of Hg per cubic metre although higher concentrations can be observed near mercury occurrences, sulphide deposits and volcanic exhalations.

Jan 1, 1973

By S.K. SHARMA, ANKUSH GALAV, G.S.P. SINGH

This paper proposes a hydromechanically coupled numerical modeling approach to quantify the influence of various parameters on the mechanical and hydraulic performance of protective water barrier pillars (PWBP). The results are validated for two case studies having pillar widths of 16 and 42 m at cover depths of 136 and 190 m and water heads of 25 and 141 m. The outcome can be significantly helpful in the rational design of these pillars in underground coal mines.

Mar 1, 2023

By Syd Peng, W. B. Guo, F. Du, L. Yang, J. Yw. Cheng

The annual ICGCM China was initiated in 2014. Up to 2023, ICGCM China has been held 9 times. In the 9 conferences during the past 10 years, about 559 papers in 17 topical areas were presented and attendance ranged from 200+ to 400+ each conference. The 42nd ICGCM China was held in Xiangtan, Hunan, China, 10/20–10/22/2023. There were 86 papers presented in 26 topical areas. In addition, an MS and PhD Research Forum was held concurrently with 36 papers presented by MS and PhD candidates in mining engineering from 8 schools. The conference plays an important role in cultivating advanced degree student talents. In this paper, all 559 papers reviewed previously were summarized. In addition, the 42nd ICGCM China is used to illustrate the current and future development trends of coal mine ground control in China. It summarizes the 122 papers (including 36 MS and PhD forum papers) grouping into, and in terms of, 26 topical areas. In addition, its unique and innovative subject areas, short summary of developments as well as conference strengths and shortcomings will also be presented.

Jun 25, 2024

By R. D. Miller, L. Schulte, J. Davenport, D. W. Steeples

Shallow seismic reflection methods were successfully used to delineate the subsurface extent of roof failure associated with the dissolution mining of a 120-m (400 ft) deep and 60-m (200ft) thick salt bed in central Kansas. Surface subsidence at North American Salt's Hutchinson, KS, salt-dissolution well field represents a potential risk to surface structures and transportation facilities. Three intersecting common depth point (CDP) seismic reflection profiles, targeting the subsurface around an actively subsiding sinkhole, possess sufficient resolution to delineate the horizontal and vertical extent of subsurface rock failure associated with the subsidence. The three seismic profiles showed a disturbed subsurface area 90 to 105 m-diam (300 to 350 ft-diam) at a depth of between 60 to 75 m (200 ft and 250 ft). Confirmation drilling verified the interpretation of the seismic data. The seismic reflection method has the potential to resolve disturbed subsurface areas greater than 23 m-diam (75 ft-diam) at this site.

Jan 1, 1994

By D. Hong

The leaching behavior of rhenium in ammonium iodide solutions with iodine as oxidant has been studied. Experiments were carried out in an autoclave. The effect of stirring speed, temperature, pH of the solution, iodine and iodide concentrations on the dissolution of rhenium was investigated. It was found that high temperature and high pH of the solutions were essential for the efficient leaching of rhenium. The dissolution rate was found to be dependent upon the concentration of iodine and iodide. It was concluded that the dissolution of rhenium under the conditions studied was controlled by mass transfer of iodine with an apparent activation energy of 15.77 kJ/mole.

Jan 1, 1997

By M. A. Ouederni, G. C. Chorosz, E. P. Déliac

This paper deals with the heat flow problems in deep workings (depth greater than 1000 m in France). The approach benefitted from experience gathered in France and South Africa. Deep mines are located in the East of France (coal in Lorraine and potash in Alsace), where the geothermal gradient can reach 4 'C per 100 m (Virgin Rock Temperatures, VRT, around 50 'C). This paper is concerned with the following topics: method of studying the heat flow problem on a mine-wide basis, specific models for heat and moisture pick-up, interfacing of heat and ventilation calculations and a case history in the Lorraine collieries. The heat flow problem on a mine-wide basis is studied in a fashion similar to ventilation networks. Each branch is considered as a "black box" where the air picks up heat and moisture (or is cooled, in the case of an air-cooler). Each box is therefore modeled as a heat transfer unit, hence the calculation of outlet temperatures (wet- and dry-bulb) from the intake ones. The whole network can thus be computed as a sequence of boxes from the air intakes towards the outlets. The second section reviews a number of models used for the assessment of heat and moisture pick-up in the "boxes", with emphasis on stopes and development ends, which are particular to the mining method in use. Two types of stopes are considered: longwall (horizontal and inclined) and cut-and-fill (subvertical). Mechanized rock breaking and blasting can be accounted for. A particular attention is given to development ends, especially complex from the heat flow point of view (rock characteristics, wetness factors, etc.) and usually quite hot. These workings, which are critical in order to secure new production areas, are studied on an average basis as well as in extreme conditions. The calculation takes into account the history of rock temperatures. The interaction between ventilation and thermodynamic calculations is still under development. The idea consists of coupling ventilation calculations with the "box" models: the first step determines the direction of air flow, hence the sequence of the boxes; thereafter the calculations yield the effect of temperature and presssures on air flows. The final section reports on the validation of the whole approach against field data. It concerns several heat flow surveys aimed at checking the models for shafts, stopes and development ends. The accuracy of the method is found very satisfactory.

Jan 1, 1987

By J. M. Wood

Green algae have been found to be much more resistant to heavy metals than blue-green algae. Several mechanisms for resistance to toxicity have been recognized in laboratory strains of Cyanidium, Chlorella and Chlamycomonas. Cyanidium and Chlorella both grow at low pH in acid mine water. Cyanidium removes metal ions from solution by precipitation as metal sulfides whereas Chlorella complexes metal ions to the cell surface i.e. cell wall) and therefore functions as an efficient ion exchange vehicle. We have shown that Ca2+, Mg2+, K+ and Na+ are of critical importance in both the resistance and bioaccumulation of toxic heavy metals.

Jan 1, 1986

By Boleslav Taraba, Antonín Taufer

Thermovision monitoring of surface temperature has been examined for the purpose of detection of spontaneous combustion of early stage. Measurements were carried out in bituminous and subbituminous coal mines. It was found that surface temperature heterogenities can be considered as common phenomenon in mine openings. However, the most of the observed temperature heterogenities were not connected with coal spontaneous combustion of early stage. These, so called [non-spontaneous combustion] temperature heterogenities in surface of mine openings were found to be caused by: l. Different conditions of heat transfer between opening surface and air stream; 2. Low temperature (natural) oxidation of coal; 3. Dissipated heat loses of working machine. Sites of early stage spontaneous combustion of coal were characterized by: 1. More significant, local rise in surface temperature comparing with low temperature coal oxidation; 2. Evolution of carbon monoxide with local concentration near the surface of such site more than about 15 ppm (bituminous coals) or 30 ppm (subbituminous coals). INTRODUCTION Mine fires are a serious hazard to life and result in a considerable loss of coal reserves. Thus, great attention is paid to investigation of new methods enabling already early detection of self-heating of coal. The earlier a fire is observed, the easier would it be to deal with. Detection methods used in coal mines are mainly based on: 1. [Mine air analysis]. Changes in composition of mine air are examined. Products of spontaneous heating of coal, not being present in mine air under normal conditions, are considered as indicators of anomalous behaviour of coal (carbon monoxide, unsaturated hydrocarbons) (Mackenzie-Wood and Strang, 1990). 2. [Temperature measurements]. Sites of higher temperature level comparing surroundings are looking for underground using various direct or indirect methods of temperature measurements. This paper summarizes experience from thermovision monitoring, as one of the latest indirect temperature measurement technique, used for the purpose of early detection of self-heating of coal in mine openings. INFRARED THERMOVISION Infrared thermovision device of AGEMA Infrared systems AB (Sweden) was used for the in situ measurements. The constant value of emissivity factor, 0.95, was pre-set as the most probable level of emissivities of coal and rocks in mine conditions.

Jan 1, 1993

By N. G. W. Cook

The conventional cyclic system of deep-level mining by drilling and blasting gives rise to an inadequate degree of stope sorting when mining thin reefs. This results in poor utilization of the capital facilities of a mine in the form of shafts, haulages, airways and associated equipment. Continuous and controlled removal of the thin gold-bearing portion of the reefs would permit better stope sorting and hence greater utilization of capital facilities. Results of experiments to develop hard rock cutting machines for mining are reported and the benefits which could be derived from their use are discussed.

Jan 1, 1969

By R. D. Miller

Application of shallow seismic reflection to problems associated with mineral exploration, mine planning, abandoned-mine detection, and environmental evaluation has been successful in a variety of geologic settings. Increased dynamic range of recording equipment and decreased cost of processing hardware and software have made shallow seismic reflection a cost-effective means of imaging geologic targets significant to mining operations. Seismic data possess sufficient resolution in many areas to detect faulting with displacement of less than 3 m in coal seams as thin as 2 m at depths of 200 m. Subsurface voids associated with abandoned mines at depths of less than 20 m can be detected and mapped. Seismic reflection has been successful mapping disturbed subsurface associated with dissolution mining of salt Complex geologic features associated with deposition of various hydrothermal minerals have been effectively mapped with high resolution seismic reflection at depths from 80 to over 300 m. Faults in sulfur-bearing cap rock over salt domes have been accurately located, allowing improved efficiency of the dissolution mining process. Shallow high-resolution seismic reflection has the potential to significantly enhance the economics and safety of mine operations.

Jan 1, 1993

By Lana Alagha, Fardis Nakhaei, Jose L. Corchado-Albelo

Tellurium (Te), a critical mineral for solar energy technologies, faces supply risk challenges that drive the development of diversified and robust production routes. This research focused on improving Te enrichment from copper tailings (CT) produced from copper porphyry (CP) ores processing, addressing the loss of ~90% of Te minerals to tailings in the flotation process of CP ores. Gravity separation and froth flotation processes were used as possible enrichment routes of Te-bearing minerals (i.e., pyrite) in CT. In the froth flotation process, synergistic combinations of reagents were tested to achieve an acceptable enrichment ratio of Te minerals. Comprehensive characterization analyses showed significant Te enrichment in the flotation concentrates. Tellurium was recovered at 90%, while the grade of Te in the concentrates was 1.4 ppm using a xanthate collector and glycol frother compared to <0.5 ppm in the flotation feed. Findings showed that Te-minerals’ enrichment was also feasible in CT using the proposed combined concentrations routes (i.e., gravity separation followed by froth flotation) by looking at Fe, Cu, and S enrichment. This study also highlighted the importance of understanding the deportment of Te minerals in different process streams to develop and optimize efficient enrichment practices.

Feb 1, 2024