Search Documents

By Mark A. White

Surface mining of multiple seams by mountaintop removal and contour mining is complex in Appalachia. Arch of West Virginia, a division of Apogee Coal, has made its operations state-of-the-art to cope with this challenge. Arch of West Virginia moved into the heart of coal mining in Appalachia when Arch Mineral acquired coal reserves and coal operations in the southern West Virginia counties of Logan and Wyoming. These reserves were initially developed at the turn of the century as underground operations. Today, though, they are mined using mountaintop removal and contour mining. The steep slopes in the mountains of Appalachia generated a method of mining referred to as contour mining. During the late 1960s and early 1970s, contour mining was introduced at these operations using front-end loaders with bucket capacities of more than 7 m3 (10 cu yd) that could load 45-t (50-ton) end-dump trucks.

Jan 1, 1995

By Caelen D. Anderson

An investigation of a hydrometallurgical method for the recovery of tellurium dioxide from cadmium telluride (CdTe) thin-film manufacturing scrap was conducted. Sulfuric acid/ hydrogen peroxide lixiviation was employed to selectively leach cadmium and oxidize tellurium to tellurium dioxide (TeO2). Experimental variables included solution pH, pulp density, oxidant (H2O2) concentration, temperature, agitation rate and residence time. After one hour of lixiviation, no noticeable increase in grade or recovery occurred; thus, all experiments were performed for one hour. Leaching results showed it was possible to recover at least 74% of the tellurium, while producing a 98% pure TeO2 product. Additionally, an apparent activation energy value of 12.1 kJ/mole (2.9 kcal/mole) was determined. This value, along with results from agitation rate experiments, indicated the reaction was primarily controlled by diffusion through the product layer. During lixiviation, partial dissolution of tellurium proved inevitable. Thus, a second step: ammoniacal precipitation was introduced to recover the aqueous tellurium as a precipitate. A statistical experimental design (DOE) was used to identify the significant effects from the residual effects. Experimental variables included precipitation pH, temperature, initial tellurium tenor and agitation rate. Precipitation results showed that it was possible to produce a low-grade (46% Te) precipitate, while recovering 98% of the aqueous tellurium species. The precipitation pH and temperature (°C) were determined as the significant effects for both the grade and recovery of tellurium. Agitation rate and initial tellurium tenor were determined as the residual effects and did not influence the grade or recovery of tellurium. An illustration of tellurium recovery, as a function of the significant effects, is illustrated in Fig. 1.

May 1, 2012

By Kevin Andrews, SETAREH GHAYCHI AFROUZ

Ground control analysis and groundwater inflow assessments for underground coal mines require in-depth field investigations including, but not limited to, geological and geotechnical core logging, downhole geophysical logging, laboratory rock strength testing, and packer (Lugeon) testing. Field and laboratory data collection are time consuming and expensive, and an initial understanding of the expected trends among various geotechnical and hydrogeological parameters can assist with the planning and optimization of geotechnical characterization studies and grouting plans. In this study, a comprehensive database is analyzed, comprised of important rock mass characteristics (hydraulic conductivity, rock quality designation (RQD), and lithology) for coal-bearing rocks in the Central Appalachian Basin. Statistical analysis of the data is completed to establish an enhanced understanding of geotechnical and hydrogeological conditions expected to be encountered as underground coal mining passes near and beneath streams and rivers. The results of the study provide valuable reference material for the coal mining industry for completion of shaft installations, mine stream crossings, environmental assessments, and grouting and mine dewatering designs.

Jul 1, 2023

By Gregory W. Gustina, Terry P. Boyle

Analysis of the structure of the benthic macroinvertebrate community, consisting of the number of taxa and the relative distribution of total numbers, is a routine method of assessing the ecological quality of streams. Various multivariate statistical techniques, which assess the structural variability of the benthic macroinvertebrate community and the relationship of that variability with natural and anthropogenic environmental variables, have utility in separation of the various physical and chemical factors associated with impact. Multivariate methodology, while computationally complex is statistically rigorous and better integrates physical, chemical, and biological data for more synthetic interpretation. Using the multivariate analysis technique, canonical correspondence analysis, we have analyzed a number of sites in the upper Boulder River Basin, Montana to determine which are the important environmental variables associated with variation in community structure. The results of this analysis an integrated with more traditional analysis of community structure and incorporated in a risk analysis for the mediation of abandoned mines and mill sites within the watershed.

Jan 1, 2000

By Steve Kral

The former mayor of Los Angeles, CA is a believer in public transportation but thinks neither his city nor the entire country is spending enough on basic infrastructure. In fact, the United States has fallen behind most other developed nations in improving public transportation, the former mayor said. Antonio R. Villaraigosa was the keynote speaker at the North American Tunneling (NAT) conference, held June 22-25 in Los Angeles, CA. The event, held every two years, is sponsored by the Underground Construction Association of SME (UCA). This years? conference attracted 1,091 underground construction professionals from around the world. The accompanying exhibition continues to grow, attracting 142 exhibiting companies occupying 162 booths. As always at NAT, registered attendees received the proceedings volume of the conference, which contains 132 papers. The proceedings volume, including a CD of the papers, is available from SME for $149 member, $139 student member and $189 nonmember. The book can be ordered from SME, NAT item #400-4, phone 303-948-4225, 1-800-763-3132, or online at www.smenet.org/store.

By Michael E. Salovich

The U. S. Department of Interior, Bureau of Mines (Bureau) has developed a prototype version of a computer application that combines hydrologic analysis with object-oriented graphics. This software is unique in that it presents analytic element analysis within an object-oriented CAD environment. Its user interface employs mouse handling, scrolling windows, dialog boxes, palettes, and pulldown menus. It can import scanned images of maps and overlay these images within the same window. This application was developed using object-oriented programming techniques. Several programming issues concerning graphics had to be resolved during development of this system. These include (1) how to represent hydrologic elements as graphical objects, (2) how to translate screen coordinates to map coordinates, (3) how to implement ?zooming? (changing the magnification level of a window), (4) how to overlay layers of images, and (5) how to import scanned images of maps. An object library was used to implement graphical user interface features such as scrolling windows and pull-down menus. Algorithms for CAD features such as map coordinate translation, zooming, and the layering of images were developed by Bureau researchers. The application has a modular source code structure and can be modified for use in other research applications.

Jan 1, 1992

By Y. Luo, S. S. Peng, C. T. Holland

Introduction A well-designed mining plan is one that minimizes cost and mining induced problems and maximizes recovery of the coal reserve. To minimize the negative effects on surface structures caused by ground subsidence due to underground mining activities, two kinds of practices are commonly employed by mine operators. One is the support technique, which leaves an area of coal unmined or partially mined beneath the structure to be supported. The other is the protection technique, which protects the structure when it is subsiding with the ground by taking advantage of the ground subsidence process (Luo et al., 1992). In designing the supporting technique, the only currently available method in the US is the one stated in the Pennsylvania Underground Coal Mining Rules (1985). However, the size of the support area designed by this method will be excessively large and result in a wasteful use of coal reserves when the overburden depth is more than 350 ft. A more scientific method is proposed in this paper for designing the support area. This method is based on a large amount of subsidence data collected throughout a number of major US coal fields and the authors' experience with monitoring and protecting surface structures that have been undermined by longwall panels. It considers the critical deformation indices that a structure can tolerate, and depth and height of underground extraction. A support area designed by this new method will not only assure the safety of the structure to be supported but will also maximize the extraction of the coal reserve. Design of support area using the Pennsylvania rules The Pennsylvania Underground Coal Mining Rules (1985) state that no underground mining activity should be permitted beneath structures where the overburden depth is less than 100 ft. An exception to these rules is provided for mine related openings that provide access to the surface for such as entries, shafts, boreholes and site-specific variances for entry development. If the overburden depth is greater than 100 ft, the mine operators should utilize either of the following: •Extraction techniques that provide for planned subsidence in a predictable and controlled manner, or •Support techniques designed to prevent subsidence damages to features identified as: •Public buildings and non-commercial structures [ ] customarily used by the public, including churches, schools and hospitals • Dwellings, cemeteries, municipal public service operations and municipal utilities in place on April 27,1966 •Impoundments and other water bodies with a storage capacity of 20 acre-ft or more • Aquifers, perennial streams and water bodies that serve as a significant source for a public water supply system, and •Coal refuse disposal areas. The support techniques require that a support area be left beneath the surface structure or feature to be protected (Fig.1). The support area should consist of coal pillars, with their size and pattern being such that their bearing strength is maximized. The total coal extraction within the support area should be limited to a maximum of 50%. The support area should be rectangular in shape and determined by projecting a line at a 15° angle from the surface to the coal seam with an offset distance of 15 ft from all sides of the structure. For a

Jan 1, 1994

By Tso-Min Shih, Ching-Hua Liu, Chung-Jen Lin, Hsi-Chiang Fang

This paper presented herein, describe the special design of an open type coal dust explosion apparatus and the laboratory works for investigating the effectiveness of the parameters on coal dust explosion and the prevention of the propagation of the coal dust explosion flame. Coal sample which were taken from the San-Ying collieries, were passed through the process of crushing ,grinding and screening to get the required particle size, ranged from 40 mesh to 200 mesh under size for testing purpose, the rock dust spreaded on the surface of coal dust and water mixed with coal dusts were employed for preventing the coal dust explosion and the propagation of the explosion flame.

Jan 1, 1991

Introduction The US mineral industry in 1983 participated in the recovery from the recent recession. Compared with 1982, the value of raw nonfuel mineral output rose 8% to $21.2 billion. The $218 billion worth of goods processed from this crude mineral output represented a 9% increase over 1982. Even in real terms, these figures reflect growth. Demand for nonfuel mineral materials, of course, depends on the overall state of the economy, which steadily improved each quarter in 1983. Of particular importance to the mineral industry were surges in key mineral-consuming sectors such as construction and automobile manufacturing. New housing starts rose one-third, to 1.7 million units, while automakers turned out about 35% more cars (6.8 million) and 25% more trucks (2.4 million) than in 1982. These are significant increases, even considering recent trends toward smaller, lighter vehicles, and multiple-unit housing. A comeback for the mineral industry, however, is bound to proceed unevenly, particularly at the beginning. Traditionally, the industry lags behind the rest of the economy during a recovery, and some mineral products respond to overall economic improvement more quickly than others. This pattern has been repeated many times and the industry is used to it. Mineral executives know it is best to be patient and cautious during the first stages of an economic upturn. Many experts say that it may take extraordinary toughness, patience, and caution this time around. Steel Improves Raw steel production - a major indicator of both material use and mineral production - rose 14% to 77 Mt (85 million st), stimulating a 7% rise in domestic iron ore production to 39 Mt (38 million It). Still, the iron ore industry operated at less than half capacity, with most major mines remaining closed for part of the year. Iron ore imports dropped 24% to 10 Mt (11 million st), so demand was partly met by withdrawals from stocks. Despite the increase in steel production for 1983, output remained far below levels of just a few years ago. For example, 1983 production was still 29% less than in 1981. Raw steelmaking capacity actually declined about 10% during the year to 122 Mt (135 million st). The industry continued to cite steel imports, especially those from developing nations, as a major cause of domestic capacity loss. As long as steel production remains weak, steelmaking metals suffer. Domestic producers of bulk ferroalloys of chromium, manganese, and silicon operated at about one-third capacity in 1983, with six of the 19 companies involved being closed all year. The US mined no manganese or chromium, and very little nickel, although the country's only nickel mine did resume production in November. Molybdenum production, at 13.6 t (15 st), was only about one-third as much as in 1982. The major molybdenum mines, Climax and Henderson in Colorado, remained closed all year. To meet demand, molybdenum stocks were halved to 19 t (21 st). Mine shipments of tungsten, another mineral tied to steel production, dropped 30% to 1.1 kt (1,200 st) of contained metal. One of the most positive responses to the general economic recovery came from the aluminum smelting industry. By the end of the year, it was operating at about 79% capacity, compared to 59% in January. Nevertheless, the 3.3 Mt (3.64 million st) of primary aluminum produced represented only a slight increase over 1982. Total bauxite imports were about 27% below 1982 levels. Production of magnesium metal rose 11% to 100 kt (110,000 st). But titanium was more typical of other

Jan 5, 1984

By H. C. Juvkam-Weld

R. Michael Craig Mr. Juvkam-Wold's article is a timely and much needed presentation of the method of depressurization to reduce ground-water inflow into mine shafts. The article is very informative and discusses the effects of depressurization upon shaft inflows adequately. However, the article omits a discussion of another important benefit of depressurization: the reduction of potential for artesian burst or, as it is also called, floor heave. Confined aquifer systems (artesian aquifers) can contain water under several hunder pounds per square inch (psi) of pressure. For example, water levels at elevations of 455 m (1500 ft) or more above the top of the Westwater Canyon member of Reply by H.C. Juvkam-Wold In general, Mr. Craig's comments are useful and accurate regarding the potential benefits of aquifer depressurization. However, two of his points require further explanation since they may lead to a misunderstanding of my paper and its predictions. These refer to his comments regarding failure to account for storativity and to non-artesian conditions. Equation 5 is indeed Darcy's steady state equation. However, as a careful review of the appendix in this paper will reveal, I have used this equation to represent semi-steady state conditions. In other words, steady state conditions are assumed at any instant of time, but conditions may change gradually from

Jan 2, 1983

By K. Cothern, S. Novack, D. A. Johnson, R. Borden, S. Pavlou

A procedure is presented for ranking hazardous waste sites for remedial decisions, and an example with application to mining waste sites is discussed. Typical contaminant concentrations are calculated from field data. Exposure indices that compare these measured concentrations with allowable limits are then computed. The limits are selected to protect both the health of humans (for both carcinogen and noncarcinogen effects) and the health of key organisms in the ecological food web. The additive exposure index for a site, defined as the sum of all contaminant-specific exposure indices, is then used in ranking the sites and assigning each a priority for remedial action. One key source of uncertainty in the process is the estimation of a typical site concentration from data that include values reported as "below certified reporting limit" (BCRL). This uncertainty is compounded in the additive exposure index and therefore may have a substantial effect on the assignment of remediation priority. A general approach is presented for incorporating consideration of BCRL data into uncertainty evaluation when assigning remediation priority designators to hazardous waste sites.

Jan 1, 1992

By E. Z. Casassa

There has been a recent revival of interest in concentrated coal/water slurries as a substi¬tute for fuel oil or for coal/oil mixtures, particularly in electric power generation. The idea is not a new one. Coal/water slurries were transported by pipeline in the U.S. in the early nineteen-sixties, and the Black Mesa coal pipeline has been in operation for several years, while in Germany, coal/water slurries were being burnt for power generation in the early nineteen-seventies, as described by Merten and Höner (1972). Since coal is not a pure substance but a carbonaceous mixture, the different chemical and physical behavior of coal/water dispersions from different deposits must be understood in order to optimize the properties of the result¬ing slurry fuels. Since minerals which are minor constituents of coal may also strongly affect slurry properties, coal chemistry may vary considerably even within a single deposit. Thus it is unlikely that there will be a single formula for optimizing the slurry properties of all coals, and even the answer for coal from a single source may change with time.

Jan 1, 1983

Ferric (Fe3+) ions are omnipresent in flotation circuits. Depending on pH and the nature of the ore body, Fe3+ ions may play a role in the adsorption of thiol collectors on sulfide minerals. To investigate this possibility, a two-compartment galvanic coupling cell was designed. This cell was used to monitor changes in contact angle of a sulfide mineral in one compartment, while varying concentrations of the Fe3+ ions in the other. The results showed that Fe3+ ions promote xanthate adsorption as indicated by the increase in contact angle. Implications of this finding in sulfide mineral flotation in general will be discussed.

Jan 1, 1998

By G. F. Revey

All underground operations have limiting factors that influence overall profitability. Hoisting, hauling, available headings, labor, milling capacity and other factors limit how much material can be removed from an underground mine. Consequently, when mines use limited labor to handle the additional rock from overbreak and to perform extra ground support tasks, productive activity is replaced by non-productive work. Mining economics are further penalized when overbreak causes dilution of ore grades. This paper reviews organizational systems that mines have used to create environments which foster the creation of successful overbreak control programs. Actual case histories document the various quality improvement techniques, worker incentives, and practical project management systems used by these mines. A brief review of controlled blasting technology sources and overbreak measurement tools is also included.

Jan 1, 1997

By H. M. Woodrooffe

In the U.S.S.R. three of the world's major-known phosphate deposits are located. These have an estimated reserve of 2,600 million short tons of contained phosphorus. The best known lies in the "Khibiny Massif', an alkalaic rock formation some 600 square miles in area with mountain peaks rising to an altitude of 3300 ft above the surrounding terrain. Location and Climate The Khibiny Massif lies north of the Arctic Circle in the Kola Penin-sula, 100 miles south southeast of Murmansk, at a latitude of 67° 30' north and a longitude of 35° 30' east. It is serviced by rail from Murmansk and Leningrad (900 rail miles south). Figure 1. The phosphate operations are centered about the two cities of Apatity and Kirovsk. The former has a population of 35,000 and is on the Leningrad¬Murmansk railway. Kirovsk, 15 miles to the east, is now a city of 85,000. The region is at the limit of the tree line with most of the ground cover typical tundra. The mean annual temperature is -4°C and, in a normal year, precipitation occurs on 240 days. Because the temperature does not exceed freezing for 300 days each year, virtually all of the precipitation is snow. The two towns are nestled between mountains and, because of the weather, extensive avalanche control systems incorporating major engineering construction have been introduced to divert snow slides away from the populated areas. General Kirovsk was first settled in 1923 and the apatite occurrences were recognized shortly after. In 1933, the first concentrator for the recovery of the mineral was completed, producing in its first year of operation 170,000 tons of concentrate. With the growth and demand for phosphate in the U.S.S.R., a second concentrator was erected at Apatity. It calve on stream in 1963. Because of the severe climate, in the early days mining was limited to 85 days per year. With the introduction of new techniques and improved mining methods, the season has been extended to 115 days.

Jan 1, 1972

By R. E. Gertsch

A mobile-modular carbon adsorption mill design and operation for small to medium sized heap leach precious metal mines is presented. In the mobile-modular strategy, charcoal columns with adsorbed metal move from small strategically located carbon adsorption loading stations to a central stripping facility and back. The design has many advantages: 1) It scales-up from pilot plant to full production. 2) It has low capital requirements. 3) Operational costs are competitive with other systems. 4) Mill production can react quickly to changes in ore grade or property area. 5) The solution circuits are simple and easy to maintain. 6) Charcoal damage is reduced.

Jan 1, 1993

By G. P. Hand

The purpose of this paper is to bring to your attention the various kinds of high performance graphites available today, their characteristics and possible applications. These materials are products of a proprietary high temperature technology developed by Superior Graphite Company. We feel we have only begun to tap the potential of this technology and the utilization of the resulting products. During the course of the paper, we shall investigate high purity, high performance graphites made from raw materials such as mined natural graphites, synthetic graphites and petroleum derivatives. We shall define their characteristics and resulting benefits to current applications, along with applications currently under development. It is our desire to stimulate speculation and development of current high performance graphites and their applications as well as ideas for new high performance products and applications. First, a little background about the process. The technology was developed through a concentrated R&D effort which culminated in 1976 in the construction of a unique furnace capable of continuously processing tonnage quantities of granular carbons at temperatures in excess of 2,500 degrees C. This process is capable of refining various carbonaceous raw materials, including natural graphites, to levels of purity and consistency that were previously unattainable in commercial quantities. Carbon contents in excess of 99.9% are currently being produced on a continuous flow-through basis. Since beginning operation in 1977, this plant, located in Hopkinsville, KY, has been expanded in stages to its present capacity of producing over 45,000 tons of purified graphites and graphitic carbons per year. In addition to the purification process, the technology used allows the introduction of selected elements into the carbon/graphite structure to provide additional benefits. Elements of interest include boron, silicon, copper, iron and rare earths. The characteristics of and applications for some of these products will be discussed later.

Jan 1, 1990

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Chloride ions and their interactions with two organic smoothing additives – Cyquest® N-900 and HydroStar® 4208 – during copper electrodeposition were explored using cyclic voltammetry and electrochemical impedance spectroscopy. The results revealed that chloride ions, up to a concentration of 40 mg/L, depolarized the copper deposition reaction. A combination of chloride ions and Cyquest N-900 inhibited the depolarization reaction during copper electrodeposition. It is proposed that the chloride ions acted as bridging ligands between copper and Cyquest N-900. Addition of HydroStar at a concentration of 2.5 mg/L depolarized the copper deposition reaction when no chloride ions were present. This behavior did not change with the addition of chloride ions at the concentrations tested, indicating that chloride ions and the polysaccharide do not interact.IntroductionElectrowinning is a major production method used to obtain high-purity copper. In modern tankhouses, copper is electrodeposited onto stainless steel blanks and then stripped, washed and bundled for delivery. Significant improvements in the quality of electrowon copper have been made over the last few decades. Additives, temperature, current density, electrolyte concentrations and agitation are known to influence the quality of copper electrodeposits (Jenkins and Eamon, 1990).The influence of chloride and organic additives on copper electrodeposition has been the subject of considerable research. The addition of small quantities of chloride and organic additives has been recognized to significantly improve the properties of copper electrodeposits. These additives are critical in the prevention of dendrite growth and the production of smooth, dense cathode deposits.Chloride ions have been reported to catalyze the copper reduction reaction and assist in the production of uniform deposits (Lakshmanan et al., 1977; Sun and O’Keefe, 1992). Moreover, it is generally agreed that chloride ions depolarize the copper deposition process at low (several millimolar) chloride concentrations. This is because chloride ions catalyze the reduction of copper (II) ions to copper (I) ions (Cu2+ ? Cu+ + e-) in the rate-limiting step of this process (O’Keefe and Hurst, 1978; Ilgar and O’Keefe, 1997; Hebert, 2005; Shao, Pattanaik and Zangari, 2007)."

Jan 1, 2016

By R. V. Ramani, J. Qin

During the mining process, the in-situ material is broken into different size ranges, from very large pieces to very fine particles. Some of the fine particles become airborne. In underground coal mining, airborne respirable dust is associated with health and safety of the miners. The amount and size distributions of airborne dust are important parameters to effective dust control measures. The design of underground mine experiments, including sampling procedures and sample analyses methods to determine these parameters are presented in this paper. A total of fifteen continuous miner cuts were sampled. The amount of dust generated during the cutting process and the relationship between total and respirable airborne dust concentrations and amounts are examined. The amount of respirable dust airborne is on the average only 0.016% of the respirable dust generated. On the average, 61% of the total airborne dust measured is in the respirable size range. The amount of respirable airborne is on the average 36% of the respirable size fraction in the total airborne dust. For equal proportion of rock and coal material cut, rock contributes about twice as much fines (=0.22 mm) as coal. Additional fundamental research is necessary to further the understanding of the airborne propensity of respirable dusts in mine atmospheres.

Jan 1, 1989

By S. Siewierski, L. Wojno

INTRODUCTION Bumps are among the most dangerous hazards in the Polish copper ore mines. Their occurrence is the result of the dynamic processes in the rock mass caused by natural factors connected with the deposition of strata and, to some extent, by technological factors resulting from the process of exploitation. In this connection, in order to ensure worker safety and choose such a technology that allows an achievement of high technological and economical parameters, a detailed knowledge of the phenomena occurring in the rock mass is required. In copper mines the basis for forecasting and control of bumps is obtained by continuous measurements and observations of the symptoms of rock mass pressure, the analysis of which ensures the accuracy of forecasting and points toward preventive means that must be applied to prevent bumps. The methods most often used for preventing bumps in copper mining are discussed in this paper.

Jan 1, 1982