Search Documents

By Richard R. Klimpel

In this paper, the old and the new commercially available reagent chemistries for the improved flotation of sulfide minerals will be summarized. The reagent classes discussed are those that meet three criteria: 1) they are being commercially used and/or large scale plant tested in North America in the last few years; 2) they are clearly different in chemical structure than commonly used commercial reagents of the last few decades and are not simply mixtures of existing reagents and/or simple changes in cation, alkyl group size, etc. and 3) the structural formulae are clearly specified in the public literature.

Jan 1, 1994

By Mustafa Akser

The Pipestone Lake anorthosite complex in Manitoba, Canada, was recently been re-identified as a potential source for titanium, iron, and vanadium. The present study utilized a 350 kg hard rock sample, which originated from the "Main Central" zone of the deposit. Commercial pilot-size equipment, such as dry low intensity roll magnets, wet high intensity magnets (WHIMS), and high tension electro-dynamic roll separators, was employed. As products, ilmenite up to 48.5% TiO2, and magnetite concentrates up to 87.9% Fe3O4 with 5.25% TiO2 were obtained. The majority of the vanadium reported to the magnetite concentrate. Subsequent characterization of various separation products shed light on the potential grade and recovery of the minerals from this deposit.

Jan 1, 1996

By T. I. Probert, B. W. Burdett, L. B. Hales

Selecting a mineral processing control system from the multitude of offerings can be a formidable task. To assist the plant designer, the material in this chapter includes the advantages and disadvantages of different equipment types, configurations, and control strategies. Selection procedures are detailed, and the importance of each step in the design and selection process is explained.

Jan 1, 1986

By F. M. Doyle, Jun Li, Milton E. Wadsworth, Ximeng Zhu, E. Peters

The electrochemical behavior of pyrite in borate/sulfate solutions was investigated using cyclic voltammetry. Three anodic peaks at approximately -0.8 V, -0.1 V and +0.5 V (SCE) were detected along with their corresponding reduction peaks. The first two peaks correspond to the oxidation of surface products. The third peak corresponds to the direct oxidation of pyrite with reaction products FeO oxides. sulfate ion and partially oxidized sulfur intermediates present as a surface film of polysulfides and So. The Few oxides and sulfur intermediates were reduced to ferrous hydroxide and HS during the negative-going scan. The HS interacted preferentially with Fe(OH), on the surface to form FeS. Excess fenous hydroxide continued to reduce to metallic iron. During the return positive-going scan, metallic iron was oxidized to ferrous hydroxide and FeS was oxidized to pyrite. These reactions are characterized by a unique double peak observed in the region -0.8 to -0.65 V. The growth kinetics of the surface sulfur film formed during anodic oxidation were studied using chronoarnperomeay. Potentiostatic measurements were well correlated by a paralinear rate equation, suggesting the formation of an intermediate passive film, associated with the simultaneous dissolution of the outer layer of the film. The reaction rates were affected by applied potential, solution pH and temperature, but were independent of electrode rotation speed. A reaction kinetics model which fitted well with experimental results, was developed.

Jan 1, 1993

By Iain M. Mason

Linear meridional zones of bad roof conditions have been frequently encountered in producing collieries working the Permian age Lithgow seam in the western coalfield of New South Wales. The prediction of such zones ahead of mining is desirable for reasons of both safety and economics. In March, 1981, we carried out an experimental, three-component in-seam seismic survey at Invincible Colliery to discover whether such zones have any unambiguous seismic effect. The underground survey was the first of its kind to be attempted in an Australian mine. The data quality was excellent with the spectra broadband and clear. Polarisation analysis disclosed two modes: one compressional; the other shear horizontal. The SH model was clearly dispersive and well gound to the plane of the seam. Modal velocities decreased by up to 15% at the fracture-swarm site. There is a strong suggestion on the RLS maps obtained here that the distributed fault zone is acting as a composite scatterer of channel waves. The P-SV and SH wave tomograms obtained show, in a general way, the distribution of stress in the coal panel.

Jan 1, 1982

By J. O. Marsden

The 1980s saw a revolution in gold extraction technology, paralleled only by the implementation of the cyanide leaching process in the late 1800s. This revolution was led by the widespread adoption of carbon adsorption processes for gold recovery, heap leaching of low-grade ores and development of a variety of oxidation processes to treat refractory ores. In the late 1980s, gold production in almost all regions of the world increased, with the notable exception of South Africa. This geographical variety is creating a greater diversity of challenges for gold metallurgists. This is due to a wider range of ore types, new and varied environmental regulations and legislation, and a requirement to select the most appropriate technology to suit local needs. North America has led this technological revolution in the gold industry and is responsible for commercialization of most of the major innovations: carbon-in-pulp, heap leaching, whole ore pressure oxidation and whole ore roasting. Process selection trends A general trend in precious metals extraction technology has been the treatment of ores with progressively lower grades. The lowest cost treatment, dump leaching of material at run-of-mine size, has been increasingly applied. ZortmanLandusky, in Montana, is successfully leaching material above a cutoff grade of 0.2 g/t (0.006 oz/st) at an average rate of about 28 kt/d (31,000 stpd). At this scale of operation and in the absence of any cyanide-consuming species in the ore, process operating costs for a ge¬neric run-of-mine leaching operation are estimated to be between 60 and 75 cents/ t (66 and 77 cents/st). One of the largest heap leach opera¬tions treating crushed ore is the Round Mountain Mine in Nevada. It processes about 45 kt/d (49,000 stpd) at an average grade of 1.1 g/t (0.032 oz/st) at a nomi¬nal crush size of 80% -19 mm (-0.7 in.). Round Mountain also treats lower grade ore above a 0.2 g/t (0.006 oz/st) cutoff by dump leaching at run-of-mine size.

Jan 1, 1993

By William G. Pariseau

The purpose of this paper is to present a design procedure for the quantitative estimation of support load requirements in underground mines. Emphasis is upon the basic features of support behavior common to a large variety of support systems-bolts, timber sets, stope fill, steel arches, concrete liners and so forth. A strong reliance is placed upon fundamental principles and modern computing techniques for their quantitative implementation. Example problems illustrate the approach. Where artificial support is required, the ground in the vicinity of the face usually stands unsupported long enough for the support to be installed. At the time of installation, the load transferred to the support from the adjacent rock is essentially zero, although in some cases there may be an initial set load, for example, from timber blocking. With the passage of time and advance of the face, ground motion loads the supports. If the support system is properly designed, then the additional loading poses no threat to the safety and productivity of operations. If not, then difficulties may arise including high maintenance costs, hazardous work conditions and reduced productivity. Of course, over-design can be equally wasteful. Quantitative estimation of support loads is therefore essential to overall efficiency in mining.

Jan 1, 1975

By Ronald C. Severson

Crystals of native gold occur in placer-type deposits. Gold, as a pure metal, is the most malleable metal known; therefore, delicate gold crystal forms should not survive mechanical transport and concentration processes involved in placer formation. To test the hypothesis that the crystalline gold is currently forming in place, two active gold-placer operations and an unmineralized background area in Alaska were examined. At these sites, rock outcrops, soil profiles, and native vegetation were sampled. At one sampling site, the soil was panned and yielded crystalline gold, as well as the more common rounded nuggets. The plants and soils were analyzed for their major, minor, and trace-element contents, especially gold. Two procedures, one a simple demineralized water leach and the other a partial digestion with acetic acid and hydrogen peroxide, were also used to extract gold and various anions from soils. The water-extractable gold ranged from <0.02 to 15.0 ppb Au in the extracting solution. This represents as much as a 104 enrichment in gold over average river water. This extractable gold is probably available to the native vegetation. Gold concentrations in the unashed dry plants from the two placer sites ranged between 0.4 and 106 ppb compared to a background range of <1 to <4 ppb Au. The presence of dissolved organic matter in the soils is thought to be responsible for the dissolution, transportation, and precipitation of gold in these placer soils, and this process is presently active in these soil profiles.

Jan 1, 2013

By R. E. Pennington

My subject this morning is coal liquefaction technology. Actually, coal liquefaction involves a number of technologies in a very complex system. The first slide shows the major components of such a system with arrows to indicate appropriate flows. The components are the facilities for coal feed preparation and handling; the coal hydrogenation or base liquefaction section; facilities for product separation and recovery, and in addition, facilities for the production of hydrogen from coal-based sources. A very rough break- out of the investments involved in these areas is given at the bottom of the slide. Investment is spread about equally among the three areas of operations Another way of looking at it is that the investments in what might be called support facilities are of the same magnitude as the base investment in the hydrogen facilities. Therefore, it is appropriate in a discussion of coal liquefaction technology to treat it as a system composed of a number of technologies. The next slide lists the various functions in the feed preparation section along with an indication of technology status. Storage, crushing, grinding, drying of coal all have been in commercial practice for a number of years. The slurrying and pumping of coal at least in water slurries, is practiced commercially also. The heating of coal slurries in oil to high temperatures under pressure is not in commercial practice and development and testing is going on by a number of people in this area. Some rather complex phenomena occur when coal oil slurries are heated to high temperatures.

Jan 1, 1975

By James P. Cooney

The global mining industry is in the process of redefining its activity and purpose in terms of sustainable development. This process is impelling a growing number of companies to engage their stakeholders on environmental and social issues. Nongovernmental organizations (NGOs) have customarily acted as critics of the mining industry&apos;s performance. A new relationship between mining companies and NGOs is emerging in the context of sustainable development, ranging from dialogue to joint action. If positive interaction among mining companies and NGOs is to succeed, clear terms of engagement must be articulated, and measurable progress toward achieving both corporate and NW objectives must be demonstrated. The experience of Placer Dome is illustrative of the rewards and challenges of engaging with NGOs.

Jan 1, 2001

By Wedam Nyaaba, Samuel Frimpong, Bruno Ayaga Kansake, Irene Akalanyaba Ateng

Haul truck capacities have increased due to their economies of scale in large-scale surface mines. These high-capacity trucks impose dynamic loads on haul roads. A previous study estimated the dynamic forces imposed by ultra-large trucks on haul roads to be more than three times the static load. These dynamic forces exacerbate haul road stresses and deformation. Current haul road response models are 2D and use static truckloads for low-capacity trucks. No models capture the ultra-large truck dynamic effects on haul road structural response. This study uses 3D finite element (FE) modeling to compute the haul road response to ultra-large truck dynamic loading. The dynamic forces were modeled using multibody dynamics (MBD) in MSC.ADAMS. These forces were used in an FE model developed, verified, and validated in ABAQUS, to simulate the response of the haul road to the dynamic truck forces. The road was modeled using an elastoplastic Mohr-Coulomb model. The results showed that road deformation decreases with increasing layer modulus and increases with increasing payload. Increasing the base modulus from 100 MPa to 450 MPa reduced the maximum deformation from 258 mm to 62 mm. When the subbase elastic modulus increased from 100 MPa to 500 MPa, the maximum deformation decreased from 160 mm to 84 mm. Increasing the payload from 0 to 120% of the rated load increased the maximum wearing surface deformation from 131 mm to 216 mm. This study forms a basis for designing structurally competent haul roads for improving haulage efficiency and truck and operator health.

Jan 7, 2023

By Kenneth K. Landes

So far my consulting in industrial minerals has been confined principally to carbonate rocks,-salt, coking coal, and glass sand. Much of this work has been for companies either too small for a full-time geological staff or unaware of the value of employing one or more qualified geologists permanently. It gave me considerable personal satisfaction to see several of the latter companies employ one or two full-time geologists after the completion of a consulting contract with them. One possible reason why some companies lack the wisdom to hire geologists is that they are dominated by engineers who still subscribe to the old idea that engineers are self-sufficient in all fields. They could have learned this from their professors. I once knew a Dean of Engineering who got purple in the face when a faculty committee was discussing the financing of a broad gauged engineering project and suggestions were made that assistance be obtained from the Schools of Business and Law and from some of the science departments tie pounded the table and shouted "Engineers are trained to handle all this!" In teaching engineering geology some years ago I used to tell the class repeatedly that the course would not make them geologists, that the purpose was to teach them

Jan 1, 1972

By Howard L. Hartman

In 1969, the OECD conducted a survey internationally to determine the status and needs for research and development in the field of tunneling. The findings also have some validity for underground excavation in general and for underground mining per se. Of the 17 countries responding to the survey, the U.S. leads in the level of support: $21.8 million and 720 man-years of effort over the last ten-year period. The total volume of R/D for the 17 countries was estimated to be $86 million and 5800 man-years. Performance of research was primarily by government agencies and public utilities (70%); the balance was conducted by private organizations and universities (15% each). In the categories of R/D subjects surveyed, three--Wk mechanics, soil mechanics, and geological exploration--outstripped all the rest in priority of effort to date. Ground support, equipment development, excavation, and environmental control received intermediate attention. The subject areas in which the least R/D effort has been expended are materials handling and systems evaluation. For the future, those R/D areas rated the most crucial to achieve technological progress in tunneling were excavation, ground support, and materials handling. The survey findings of tunneling activity indicated (1) a disturbingly low level of R/D activity in the private sector, (2) the necessity for a reordering of priorities in directing research efforts in the future, and (3) a lack of recognition to date of the importance of systems evaluation in R/D activities.

Jan 1, 1970

By T. Petrov

This study was performed to analyze the behavior of the blowing curtain face ventilation system modified with a specially designed regulator, called Wing Regulator. The purpose of the regulator is to extend the airflow penetration depth toward the face and allow effective face ventilation at curtain setback up to 13.7m (45ft) from the face. A small scale model of the Wing Regulator was successfully tested in the Mine Ventilation Laboratory at the University of Kentucky. Then a prototype of the proposed regulator was tested in full-scale in mine environment. Series of three dimensional simulations were performed to support this research using validated CFD code. This paper presents results of the performed studies and discuses the advantages of using the Wing Regulator. Presented information relates to the US Provisional Patent Application No 61/818,112.

Feb 23, 2014

By M. S. Klima

Proper analysis of washability data can lead to the development of a maximum yield coal preparation plant flow sheet. Simulations, as simple as spreadsheet mass and water balancing, are important in examining yield maximization and middlings liberation. Key to such attribute tracking flow sheet simulations is the distribution model, expressing the probability of a species reporting to the product stream. There are many such models in the literature. This paper examines a functional form that can represent or fit most of the proposed distribution functions.

Jan 1, 1997

By M. Spangler

FirstMiss Gold installed a supervisory control system based on Pavilion Technology&apos;s Process Insights neural network software and Oil System&apos;s PI data historian. The primary goal of the system was to control the acid preconditioning circuit. However, our first successful control loop was on the limestone feed rate to the neutralization circuit. The information gained by modeling these circuits and the better control provided by the system has resulted in reagent savings of over $80,000 per month.

Jan 1, 1995

By C. Patrick, D. Puckett

The feasibility of monitoring the locations and vital statistics of equipment and personnel in surface and underground mining operations has increased with advancements in radio frequency identification (RFID) technology. This paper addresses the use of RFID technology, which is relatively new to the mining industry, to track surface equipment in mine pits, loading points and processing facilities. Specific applications are discussed, including both simplified and complex truck tracking systems and an automatic pit ticket system. This paper concludes with a discussion of the future possibilities of using RFID technology in mining, including monitoring heart and respiration rates, body temperatures and exertion levels; monitoring repetitious movements for the study of work habits; and logging air quality via personnel sensors.

Jan 1, 1999

By N. Sheikh

In galena flotation, lead ethyl xanthate, Pb(EtX)2, is precipitated and is physically adsorbed in the form of multilayers on the chemically adsorbed first layer of Pb(EtX). 1,2) The solid particles are coated with layers of Pb(EtX)2 in heterogeneous manner over surface areas possessing both anodic and cathodic character (3,4) It is anticipated that the mode of formation of Pb(EtX)2 and the number of ions present, together with stable or unstable by-product species, have great influence on the surface characteristics of galena. The information obtained from a study of these parameters may have important practical applications in flotation. Lead ethyl xanthate is sparingly soluble in water. The metal and xanthate ions released to the aqueous solution during its dissolution undergo various types of reactions depending upon the pH values of the system. Extensive work (5,6) has been carried out to elucidate the mechanism involved in acid decomposition of xanthate ions. Different decomposition paths (7,8) have been proposed for the hydrolytic decomposition of xanthate in neutral and alkaline solutions, The concentrations of lead ions vary due to a number of chemical reactions, regulated by the pH and the temperature of the bulk phase. The hydrophobic character of Pb(EtX)2 may change with the nature of chemical reactions. Some of the numerous by-product species in solution may adsorb on the solid and change the properties of surface film either favourably or adversely. The flotation performance of galena, therefore, may depend to a considerable extent on the physical and chemical stabil¬ity of Pb(EtX)2 layers. Since little work has been reported in literature dealing with the stability of Pb(EtX)2 and its correlation with the flotation of galena, attempts have been made In this study to evaluate the behaviour of freshly formed Pb(EtX)2 in aqueous systems at various pH values.

Jan 1, 1971

By Marline J. Veesaert

Urban quarries offer one of the greatest opportunities for profit in non-metallic mining with limited financial risk IF properly evaluated, planned and developed to meet market needs. Location, with respect to market, is the prime consideration. Geologic considerations and quality of rock are nearly as important. Cost factors and return on investment (ROI) are the principal financial considerations. Risk of capital is determined by weighing all factors that should be considered and how well judgements are based on information acquired. It is a simple, true axiom of business that an investment must be founded on amount of capital required with its expected return plus profit, expertise required to operate and time involved. Urban quarries generally offer excellent stone product market opportunities. Costs of land with mineral containment and processing operations are much greater than in rural areas. Environmental problems have become increasingly severe. Competition from other quarries in the market area is usually directly proportional to the profit attractiveness. Risk of capital (initial, developmental and operational) can be evaluated and reduced only by thorough analysis of the entire situation. Time and money expended on planning and preliminary investigations probably represent the most productive investment of available company resources.

Jan 1, 1977

By K. L. Wiley

In-situ leaching, initiated in 1986 at San manual, was economically developed in 1989. The primary reason for this lag time between startup and viable production was the time required for technical development. The technical development pursued comprised detailed design, development, and implementation of in-situ well construction methods, formulation of suitable well pattern arrays, and the development of extensive hydrogeologic and geochemical knowledge of the mineral deposit. Since 1989, the in-situ leaching program has become a viable and cost effective method to extract copper from the supergene mineralized zone of the San Manuel deposit. The in-situ leaching methods that are currently utilized have been progressively expanded and continually developed and will became the cornerstone of copper production from the San Manuel oxide mineral deposit. This paper presents an overview of the supergene hydrogeology, current design techniques, drilling methods and well completion, pump determination and setting, solution management, and future plans for the increased extraction of copper by in-situ leaching methods at the San Manuel mine.

Jan 1, 1993