Search Documents

By Vikram P. Mehrotra

A laboratory investigation was carried out to study the influence of asphalt, bentonite and corn starch binders on the pelletization kinetics of coal fines and on the quality of the resulting pellets. Pellet quality was evaluated in terns of the compression strength, impact resistance (drop test), abrasion resistance and resistance to severe weather conditions. The amount of binder addition did not significantly influence the pellet growth kinetics. However, the pellet quality varied markedly depending upon the type and the amount of binder used. Experimental results are explained on the basis of the mechanism of interaction between the coal particles and the binders. Of the three binders tested, corn starch proved to be the best in all respects but for the resistance to water penetration. Finally, a combination of corn starch (imparting strength) and asphalt emulsion (imparting resistance to water penetration) was found to yield the best quality coal pellets.

Jan 1, 1981

By I. Demers, A. Blier, M. Mbonimpa, M. Benzaazoua, B. Bussière

The Doyon Mine in Quebec, Canada, evaluates the possibility of desulfurizing its tailings to produce material to be used as cover for the acid-generating tailings disposal site. Laboratory tests showed that a single-layer cover made of desulfurized tailings placed over reactive tailings can prevent the generation of acid mine drainage. Modeling with the software Vadose/W was used to optimize the design parameters, namely, cover thickness, water table position and residual sulfide content of desulfurized tailings following laboratory work. It was found that the optimal configuration includes a 1-m (3.3-ft) desulfurized tailings cover containing 0.8% S, with the water table kept at the interface between the reactive tailings and the cover. To maintain the cover performance to reduce oxygen flux toward acid-generating tailings even in the event of a long dry period, a sand layer is suggested to protect the cover from excessive evaporation. It is possible to reach the environmental objective for oxygen flux chosen for the Doyon Mine (10 mol/ m2/year) with the protective sand layer, even in extremely dry conditions.

Jan 1, 2009

By Jr. Matthews

The Candelaria copper-gold deposit is located in Region m of Chile, 805 kilometers north of the capital, Santiago. Candelaria was discovered in 1987, following a six month exploration program. In late 1986, induced polarization (IP) surveys outlined an anomalously high response within the area of interest. The first test hole bad three intersections totaling 49 meters, with an average grade of 1.97% copper. Drilling eventually outlined approximately 390 million tonnes, grading 1.09010 copper and 0.26 grams/tonne gold. Production began in early 1995 and is estimated at 120,000 tonnes copper and 80,000 ounces gold annually.

Jan 1, 1996

By Paul Eimon

The 1981 Fall field trip of the Denver Region Exploration Geologists' Society focuses on Creede. That is appropriate - because significant mining history has been made and is being made in this off-the-beaten track, high-country mining district. Creede is one of the few Colorado bonanza towns which was big in the 19th Century, had its ups and downs, and produced almost continuously since its discovery. Creede is important to geologists for its: precious and base metal production, current exploration activity, and research into near-surface hydrothermal systems. United States Geological Survey research and field geologists zeroed in on Creede some 25 years ago and their steady, consistent work is now being spotlighted and appreciated.

Jan 1, 1981

By W. K. Dressel

Over 2 million tons of steel furnace dusts are produced each year in the United States. Recycling of these dusts rather than disposal would conserve mineral resources, reduce land requirements for disposal, and decrease pollution. In addition to the iron content, the dusts contain appreciable amounts of zinc and lead. Removal of lead and zinc with simultaneous reduction of Iron oxide has been achieved by inert atmosphere roasting of carbon-containing pellets prepared from steel furnace wastes. High- and low-carbon wastes were blended to obtain mixtures with sufficient carbon to serve as a reductant during subsequent roasting. The mixtures were pelletized with the addition of bentonite and water, and the dried pellets were roasted in a stream of nitrogen at temperatures ranging from 900" to 1,150° C. Zinc and lead contents were reduced to the 0.1 percent level or less by roasting mixtures containing as little as 7 percent carbon for 1 hour at 1,100° C. ton metallization increases with available carbon content; 50 percent metallization is achieved with 7 percent carbon, 85 percent metallization with 12.5 percent carbon, and over 95 percent metallization when the pelletized mixtures contained in excess of 20 percent carbon.

Jan 1, 1973

By T. C. Page

The Yarnell gold depoSit, located in the Weaver mining district of Yavapai County, Arizona is found within a structurally controlled, hydrothermally altered zone that occurs within a 1700 Ma granodioritic intrusive. Both potassic and sericitically altered rock that occur around and above the low-angle northeast striking Yarnell fault are known to host economic gold mineralization; a wider envelope of weakly-propylitic alterred rock also occurs in this area. During mineralization, strong sericitization accompanied several stages of quartz ± adularia veining, stockwork formation, and localized silicification and potassic replacement, in association with deposition of specularite, pyrite (now oxidized), and gold. The footwall of the fault is also sericitically altered but poorly mineralized. Mineralization along the Yarnell fault continues both northeast and southwest from the main deposit although the thickness of the zone and associated alteration envelope diminish away from the orebody. A sample of undeformed illite taken from the Yarnell fault zone was K/Ar dated at 69 ± 1.6 Ma; this date reflects a minimum age for both mineralization and latest movement on the fault. Gold mineralization is accompanied by modest increases in Ag, As, Cu, and Mo content. Both CO2-and H20-rich fluid inclusions were studied and suggest mesothermal pressures and temperatures of formation for the deposit.

Jan 1, 1992

By A. M. Abouzeid, R. Hogg

Materials transport is involved in all phases of mineral processing. Bulk transport is necessary for moving materials between unit operations and through processing devices such as grinding mills. Differential transport is a primary mechanism for most separation processes. The basic mechanisms of transport and flow in particulate materials are reviewed and their role in materials handling and storage and in the performance of processing operations such as grinding and separation are discussed. Specific examples are used to illustrate current understanding of these transport phenomena and to indicate important research needs and opportunities.

Jan 1, 1989

By Bernd Friedrich, Elif Emil‑Kaya, Merve Papakci

In the production of SmCo permanent magnets with excellent temperature stability, corrosion resistance, and oxidation resistance, samarium (Sm), one of the rare earth elements (REEs), and cobalt (Co) are employed. Cobalt (Co) is a crucial component in tool materials, nickel-based alloys, tablet and smartphone batteries, and electric car batteries. REEs and Co have been listed as critical raw materials by the European Union Commission for many years. Due to the ever-growing demand for Co and REEs in technological applications, the recovery of these elements from secondary sources has garnered significant interest. There are two types of SmCo magnets, one of which contains a high amount of iron, approximately 15.2%. This paper focuses on the recycling of Fe-bearing SmCo. In this study, an oxidative leaching process with nitric acid was developed to eliminate iron through in situ hydrolysis and to dissolve REEs and Co. The influence of experimental conditions on the formation of an amorphous iron compound through the hydrolysis of Fe3+ in a nitric acid environment was thoroughly examined based on a Taguchi orthogonal array. The optimal parameters for oxidative leaching were determined to be an acid concentration of 3 mol/L, a solid-to-liquid ratio of 1/10, and a process temperature of 60 °C.

Feb 15, 2024

By John D. Abbatt, H. B. Newcombe

The Eldorado Epidemiology Project formally began in late 1978. It consists of a retrospective cohort study, to be followed by and to leave in place the mechanism for a prospective cohort monitoring program. These present and future activities are intended to merge into one another. The current study includes all Eldorado employees past and present for whom records are available. The objectives of the undertaking are - 1) to obtain cause-and-effect, dose-response data with which to evaluate the risks to workers in radon and radon daughter containing atmospheres, and to provide additional quantitative information on which to base possible improvements in working conditions; 2) to identify any dead employees of E.N.L. whose cause of death suggests that a potential compensation claim right exists for their survivors, and to similarly identify living ex-employees of E.N.L. whose work histories and states of health suggest potential compensation claim rights. The nature of the study has been determined by the history of Eldorado, which will be described briefly. Eldorado began (as Eldorado Gold Mines) in the late 1920's, operating relatively unsuccessfully in Manitoba. In 1930-31 the emphasis shifted from gold to uranium, and what became the Port Radium mine was first staked. From the very early 1930's until 1942 the company's purpose was almost entirely devoted to the mining of pitchblende - uranium ore - from the Port Radium site, and the extraction of radium from this ore at the Port Hope refinery in Ontario, a process from which the uranium was a largely stockpiled byproduct. In 1942 the company was requested by the Canadian government to accelerate the production of ore, and of uranium. At the same time, all its stockpile of uranium (then being stored in silos as a "waste" product which might later "come in") was acquired for the Manhattan Project. In 1944 the company shares were bought by the Canadian government and the company itself became Eldorado Mining and Refining (1944) Limited; it has operated as a Crown corporation ever since. The name was changed to Eldorado Nuclear Limited in 1968. The Port Radium mine was closed in 1960, and since 1953 the Beaverlodge uranium mine complex has operated on the northern shores of Lake Athabasca. Radium production was discontinued in 1954 when the radium circuit was taken out of the refinery, and since that time the refinery's products have been various types of refined uranium (uranium dioxide, uranium trioxide and uranium hexafluoride) plus metallic uranium. The refinery, of course, processes the company's own yellowcake but as it is one of only five refineries in the western world, most of its work consists of custom refining for a large variety of customers. In addition to the mining and the refining operations, there have been three other divisions involved, and these are, respectively, Aviation, R. & D., and Exploration, in addition to the financial, corporate, administrative and support activities. MATERIAL AND METHODS The human study population (Abbatt, J.D. et al., 1980) consists of all Eldorado employees who have ever worked for E.N.L. and for whom records are available. The total nominal roll to December 31, 1980 is approximately 21,000 and consists of employees of the Mining, Refining, R. & D., Aviation and Exploration Divisions, as well as a relatively small number of other employees (Head Office, etc.). The basic epidemiologic design, as has been mentioned, is for a retrospective cohort study merging into a prospective cohort study, and depending very heavily upon automated record linkage and file matching. The original design called for an initial assembly of the bulk of the nominal roll, prior to the first of two matches with the National Mortality File. The first of these two matches is now complete and the second is to be separated from it in time by 18 months to two years. The second match will be the definitive match prior to the analysis, the interpretation of the data, and the publication of the results. The period between the two matches was designed to permit completion of the nominal roll, including: - addition of previously missing individuals and groups, elimination of duplicates, and amplification of identifying information, - assembly of work histories and exposure information for each individual, - digestion and application of lessons and modifications resulting from the first match with the National Mortality File at Statistics Canada, - preparation of files for the definitive second match. The analysis of data will be carried out by the National Cancer Institute of Canada Epidemiology Unit based at the University of Toronto. This group, with whom Eldorado Nuclear has a memorandum of understanding, have for a variety of reasons, including their familiarity with record linkage and their expertise, been members of the Project Team since

Jan 1, 1981

By R. D. Willette

The Hector Mine deposit in the California Mojave Desert has a magnesium-rich clay that formed when lithium and fluorine were introduced into isolated fine lacustrine volcanic sediment during the Pliocene. The intensely deformed deposit has been supplying the highest grade thixotropic clay to the coatings industry for over half a century. A thixotropic clay displays the property of changing from a gel to a sol when shaken, and increases in strength upon standing.

Jan 1, 1995

By Hitch M.

Many mining wastes, especially those from the metal mining industry, have traditionally been treated as a matter of little or no value and in practice a cost burden. Some wastes, due to their reactivity characteristics, have emergent values that go beyond purely economic and into the environmentally beneficial realm. This paper discusses the changing paradigm of mine waste management. Such fundamental parameters such as cut off grade, and strip ratio, are positively impacted by the revaluation of waste rock material. Mine rock waste can now be seen as a commodity of value, similar to the underlying ore being mined and influences the economic performance of suitable projects. This valuable material can be used for industrial purposes including acid neutralization as well as the capture and long-term disposal of anthropogenic carbon dioxide. The Turnagain Nickel project, located in northern British Columbia serves as an example of how waste rock material can become an important matrix for carbon capture and sequestration and can benefit economically from it. By producing material that has emergent economic value as well as carbon capture and sequestration capabilities, the sequestration matrix producer is a beneficiary of new carbon credits that have a market value and is looked upon favourably by regulatory authorities and affected stakeholders.

Jan 1, 2010

By R. E. Le Messurier

GENERAL DESCRIPTION The mines are located at Broken Hill in the western part of New South Wales, Australia, 930 km west¬northwest of Sydney. Mining Methods Where pillars must be left between stopes, extraction of a block of ore between two or more levels is carried out in stages: 1) Stopes are mined overhand by horizontal cut¬and-fill stoping, or by long-hole stoping. The various methods of horizontal cut-and-fill stoping used are desig¬nated as: -Loader cut-and-fill stoping with horizontal blast¬holes and diesel load-haul-dump (LHD) units. -Open stoping with horizontal blastholes and com¬pressed air or electric scrapers, or with diesel or electric LHD units. Square-set timber stoping, where ground condition precludes open stoping. The backs are sup¬ported with timber square sets. Pattern rockbolting of the backs may be used as an intermediate stage between open stoping and square-set stoping. 2) Vertical pillars are mined by undercut-and-fill stoping or by vertical crater retreat stoping. 3) Where a horizontal pillar has been formed below the level above the primary stope, this level pillar, usually 6.1 to 8.2 m in depth, may be mined by over¬hand square-set stoping or by undercut-and-fill. Long-hole stoping is used at the Zinc Corp. (ZC) and New Broken Hill Consolidated (NBHC) to mine parts of the zinc-rich A and B lodes. Drilling is carried out from drill drives and, in some cases, sills. Hole sizes used are 165 mm (61/2 in.), 110 mm (4'h in.), and 65 mm (21/2 in.) nominal diam with hole lengths being limited to 50, 30, and 20 m respectively. Ammonium nitrate-fuel oil (ANFO) and water gel explosives are used. Broken ore is loaded from drawpoints at the bottom of the stope using rubber-tired diesel-driven LHD units which deliver ore to an orepass. Annual production at Zinc Corp. and NBHC accord¬ing to mining method is given in Table 1. At Zinc Corp. mining is being carried out at depths varying between 200 and 832 m. At NBHC it ranges from 528 to 915 m below the surface. The average travel time to the stope is 30 to 45 min. GENERAL ORE BODY REQUIREMENTS Size, Shape, and Dip There are six separate lodes which carry minable ore in the mines of Zinc Corp. and New Broken Hill Consolidated. The lowest of these and the main ore bodies presently being mined at Zinc Corp. are the lead lodes, consisting of a siliceous fluoritic ore body (No. 3 lens) and overlying it a calcite rhodonitic ore body (No. 2 lens). Each possesses characteristic ratios of lead, silver, and zinc, although the grade within each lens is variable, in places being as high as 30% Pb. There are also low¬grade portions which consist chiefly of poorly mineral¬ized rhodonitic material. No. 3 lens terminates within the Zinc Corp. leases, while No. 2 lens continues into the NBHC leases where it continues to provide a significant proportion of pro¬duction from the mine. Overlying the No. 2 lens are the various zinc-rich ore bodies. In ascending sequence these are lower No. 1 lens, upper No. 1 lens, A lode, and B lode. A typical assay for the small No. 1 lens group ore bodies is 8% lead, 50 g/t silver, and 20% zinc. The `A' lode is a large low-grade ore body in which the higher grade sections assay 4% lead, 30 g/t silver, and 10% zinc; larger quantities of lower grade ma¬terial also occur. B lode, the main zinc lode, typically assays 5% lead, 30 g/t silver, and 17% zinc. B lode increases in size as it extends south, and in NBHC is a major ore body, contributing about 52% of the production. All the lodes pitch south, the average pitch being 0.52 rad (30°) in the Zinc Corp. leases and rather flatter than this in the NBHC leases (see Figs. 1-3). The ground is all competent rock. Production requirements at Zinc Corp. are 900 000 t and 1 200 000 at NBHC.

Jan 1, 1982

By B. Stewart, R. Li

Coal waste materials inhibit the direct establishment of vegetation due to adverse physical and chemical properties, particularly low water retention and high potential acidity. The Moss #1 coal refuse pile is located in Dickenson County, Virginia, and was idled in the late 1980s with little topsoil resources available for final closure. The refuse was acidic (Total S = 0.38%; pH = 3.6), black in color and high (70%) in coarse fragments. The refuse also had a low water-holding capacity (4.5% in < 2.0-mm fraction). A small plot experiment was established on the refuse pile to evaluate the effects of liming rates (50% and 100% of lime requirements) and topsoil thickness (15, 30 and 60 cm) on vegetative growth and leachate quality. Liming and topsoil amendment increased the surface soil pH from <4.0 to >6.0 over a two-year period, which resulted in greater vegetative cover and biomass than the control plots. All topsoil treatments resulted in greater vegetative cover and biomass than plots treated with lime only. This was due to improved surface soil physical and chemical properties. A topsoil treatment of 60 cm gave the thickest vegetative cover and biomass yield. Such a treatment, however, would be cost-prohibitive at this location. Applica¬tion of 27Mg ha`1 of lime to the refuse surface along with 15 cm of topsoil produced acceptable two-year vegetative cover and biomass, and this appeared to be the optimal treatment for this particular situation. Both liming and topsoil had no affect on leachate pH and the electrical conductivity of leachates collected below the plots. This suggests that surface revegetation will have little effect on the quality of water draining through the pile. Therefore, long-term water-treatment requirements may not be reduced by successfully revegetating the pile surface.

Jan 1, 2000

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

There are several methods (empirical, statistical, and machine learning tools) to calculate blast-induced ground vibration. Still, due to complications in the blasting procedure, under varying blasting loads and strata conditions, it is not easy to predict and simulate blast vibration precisely. Therefore, a study was conducted to simulate the field blast data in Ansys software using explicit dynamics. For this study, monitoring of ground vibration for 20 single hole blasts was carried out. The density of emulsion explosives was in the range of 0.9 to 1.15 g/cc. In the laboratory, rock properties were determined from the rock sample collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and the density of the emulsion explosive were also determined. These parameters were used for numerical analysis to know the ground vibrations at specified points. The results of ground vibration predicted by the model are validated using field data.

By V. Rajaram

The oil shales located in the Appalachian Basin cover an eight-state area of the eastern U. S., and are referred to as Devonian (black) shales. These shales have been exploited for their gas potential for several years. The Institute of Gas Technology (IGT) has conducted research since 1972 on the production of shale oil from the Devonian shales, and this resulted in the development of the HYTORT process. This process demonstrated that the yield from the Eastern oil shales can be greater than the value indicated by the Fischer assay method. IGT estimates that 423 billion barrels (67.3 x 109 m3) of oil could be recoverd by HYTORT processing of surface-minable eastern U. S. shales. Recently American Syncrude Corporation and Southern Pacific Petroleum N. L. have proposed oil shale projects in Kentucky. This paper will describe the surface mining and retorting techniques that have been studied for exploitation of the Devonian shales, and enumerate the problems that have to be overcome before commercial production can be realized from these shales.

Jan 1, 1983

L.R. Bower In regard to the paper by J.B. Gwiazda, it makes a highly technical approach to show that the µ factor used by designers of lemniscate-guided roof supports has never really been confirmed as a maximum and assumes that convergence is vertical. Also, the paper does not appear to take into account deflection of structures, which occurs when the lemniscate and base members are fully loaded to their maximum stress level, nor the front to back line of the support in relation to differential roof to floor movements caused by strata movements under pressure. It is not unusual for differential movements to be slightly diagonal to the line of the support, particularly in faulted areas and on gradient faces. The paper also does not take into account consolidation of fines immediately above and below the support. Generally speaking, any differential movement is from face to waste and under these conditions the µ of 0.3, which appears to be an international standard, has worked in practice. However, if the face end of the support is lower than the waste end, then the µ of 0.3 can be considerably increased, giving rise to the damage mentioned in the paper. The ideal design should aim for a slightly forward bias in the lemniscate guide so that the last increment of setting is toward the face, tending to close any fissures that may have developed during the support advance cycle. The support should also be fitted with positive set valves to ensure that a high setting load density is attained to minimize bed separation. As far as powered supports are concerned, convergence is irresistible and all powered supports converge at their rated yield load. A similar principle can be applied to the differential roof to floor movements to drastically reduce the very high forces that would otherwise be applied to the lemniscate structures and pins and that, in turn, are transferred to the base arrangement and floor loading. Any differential movements are usually catered for by the 0.3 µ factor or deflection of structures in the lemniscate guide arrangement and consolidation of the floor. The floor loading, due to differential movement, is in addition to the support convergence load and requires additional bearing area to avoid possible floor penetration. Some seven years ago, Fletcher Sutcliffe Wild Ltd. (FSW) introduced a lemniscate-guided shield support where the lemniscate linkage is connected to the roof bar through two horizontally converging rams to allow differential movement to take place above a given rated figure. This is a known force and can be guarded against, whereas with rigid connections the forces, as yet, are unconfirmed. By careful design, a horizontal force in excess of 6 MN (60 tons) opposes differential movements for a total ram loading of only 2.5 MN (25 tons), or 1.25 MN (12% tons) each. This principle can considerably reduce the length and weight of the support in comparison with a rigid pin-type structure ; also, the yield load rating can be increased without affecting the lemniscate forces. The graph shows the tensile and compressive forces in a lemniscate linkage of a support with and without hydrostore. These forces react into both the roof beam and base members and, as can be seen from the support height to linkage load graph, a considerable reduction in these reactions is gained by the use of the FSW patented hydrostore system. Floor loading is considerably reduced under maximum µ conditions, and by allowing the roof bar to move with the strata, some degree of improvement to strata control is achieved in line with the assumptions in the paper. In practice, these movements have only been in the region of a few millimeters, which, in turn, reflects on the improvements to strata control by the addition of positive set valves. Supports to this design of both 450- and 280-t (496-and 309-st) rating have been successfully used in the United Kingdom for several years, negotiating many faulted areas without one single reported need for repair or maintenance. This includes supports left unattended during the year-long strike, proving the reliability of the system.

Jan 8, 1986

By H. Walqui, S. K. Kawatra, C. H. N. Jeltema, T. C. Eisele

"The literature contains many cases where the shape of hydrocyclone efficiency curves vary from the ideal “S” shape. These often appear as changes in slope, or inflections. These inflections can be divided into two categories: “coarse” inflections, which are caused by differences in the density of the minerals being separated, and “fine” inflections, for which there are a number of competing hypotheses concerning their cause. The existing literature addresses either the fine inflection or the coarse inflection, but no studies have reported both types of inflection occurring at once in a single hydrocyclone test. This paper presents hydrocyclone results from both in-plant studies and laboratory experiments that show both coarse and fine inflections. The industrial significance of both types of inflections is discussed. Hydrocyclone efficiency curves show the probability of any given particle reporting to the hydrocyclone underflow as a function of its size. Selectivity functions, S(d), are used to represent the fraction of the feed material in size fraction “d” that reports to the hydrocyclone underflow. Plotting this selectivity function against particle size leads to the standard S-shaped efficiency curve shown in Fig. 1. In the “uncorrected” curve, the tail of the curve does not go through 0%, because a portion of the solids are bypassing classification. This happens as a result of their being carried along by the water, and is most important for the finest particles. The curve can be “corrected” based on the fraction of the feed water that reports to the underflow, represented by the bypass fraction, Rf. The corrected curve then normally passes through 0%, as shown in Fig. 1.The act of correcting the curve shifts the value of the d50 size, which is the size that has an equal probability of reporting to either the overflow or to the underflow. Correcting the curve to account for the bypass fraction makes it easier to compare cyclone performance under conditions that cause the quantity of water in the underflow to change, but that do not alter the actual corrected cut size (d50c).The corrected efficiency curve can be expressed closely by equations such as Plitt (1976):"

Jan 1, 2015

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

Many modern industries rely on rare earth elements (REEs) to produce products that are essential to both civil and defense applications. In a prior study (Vass et al., 2019), the authors showed that REE grades in acid mine drainage (AMD) and associated byproduct precipitates from AMD treatment (AMDp) warrant evaluation as a feedstock for REE production. The current work extends that effort through a broad survey of 141 AMD treatment sites in Northern and Central Appalachia. In this study, 185 raw AMD and 623 AMDp field samples were obtained and analyzed to assess the REE and major metal concentrations. Results show that an average of 282 μg/L and 724 g/tonne of REEs occur in AMD and AMDp respectively. Additionally, both basins contained similar distributions of REEs, and these distributions tended to favor heavy and critical REEs when compared with traditional REE ore deposits. Geospatial analysis identified a total resource of 340 tonnes stored at the 141 sites sampled in this study. While this analysis did not quantify the basin-wide REE inventory, it does indicate the impact that processing cut-off grades will have on the overall AMDp resource base.

By Todd L. Hollingsworth, Jeremy K. Hobbs

In 2001, the Radomiro Tomic Mine located near Calamq Chile, added a tertiary crushing facility. An 84" wide mobile tripper is used to fill their tertiary crushing storage facility. This paper is a we study to demonstrate the drive and control systems in use on the tripper. Of special note is the design concept used to allow the system to operate multiple motors in both demand and regenerative modes through a single VFD. Also noted is the use of touch screen local controls, handheld radio controls, starting/stopping/ braking philosophies, safety device interfaces, and the local to remote control interface.

Jan 1, 2004

By B. F. Westfall

Throughout the 1960&apos;s and 1970&apos;s world trade grew rapidly, reaching a peak of USS1.8 trillion in 1980. Since then the world recession of the early 1980&apos;s shrunk trade to about US$1.6 trillion. The reduced cash flow to developing economies made it difficult to service their huge international debts, Nowadays lenders are reluctant to grant Third World countries additional credit. The shortage of export financing, plus trade barriers set up by developed countries, is further inhibiting international trade. Therefore, countries are turning to new and creative alternatives to financing imports of consumer as well as of investment goods. Non-cash transactions, including different forms of countertrade, are rapidly growing alternatives to traditional trade financing patterns. In 1983 about 30% of international trade, or close to US$600 bill ion, were presumably done by non-cash transactions, up from barely 2% in 1976. By year 2000, half the world trade is likely to be conducted on basis of barter. As of mid-1984 some 88 nations used countertrade regularly and Governments of at least 15 Latin American countries had arranged or mandated commercial countertrade.

Jan 1, 1986